Differential expression of human ferritin H chain gene in immortal human breast epithelial MCF-10F cells

This study investigated fractures of the cement layer between a crown and a die. Model crowns were luted on dies with zinc phosphate cement and various magnitudes of load were applied. Surface strain on the crown was measured using strain gauges. Seal was evaluated using dye penetration and tensile tests. Results showed that cement fracture affected surface strain behavior on the crown and was detected using the surface strain measurement. The dye penetration test and the tensile test could not be used to detect the cement fracture. It is suggested that the three-dimensional relative positioning between the crown and the die affected the development of the cement fracture.     

Effect of tooth surface roughness on marginal seating and retention of complete metal crowns

STATEMENT OF PROBLEM: Retention and marginal adaptation factors have major influence on the failure of cemented complete veneer crowns. PURPOSE: This study investigated the effect of axial surface roughness on the marginal seating and retention of silver-palladium crowns luted with zinc phosphate, glass ionomer, and resin cements. MATERIAL AND METHODS: Coarse and fine diamond stones were used to create various surface roughnesses of premolars. A milling machine was used to control the height and angle of the axial walls of tooth preparations. Ten cast metal crowns in 6 subgroups were luted with 3 cements (Phosphacap, Fuji Cap I, and Panavia 21). Marginal seating was recorded with a Digimatic indicator. Retention was determined by measuring the tensile force required to remove a metal crown with a Lloyd testing machine. RESULTS: Two-way analysis of variance revealed statistically significant differences (P <.001) in retention for both luting cements and surface roughness. No significant difference was recorded for marginal seating relative to roughness (P =.860) and interaction effects (P =.204). Tukey-HSD tests revealed substantial differences in retention among Phosphacap, Fuji Cap I, and Panavia 21 cements. Significant differences were not confirmed in marginal seating between Fuji Cap I and Phosphacap cements with coarse diamonds, and Phosphacap and Panavia 21 cements with fine diamonds. CONCLUSIONS: The best retention for complete metal crown was demonstrated for tooth preparations ground with coarse diamonds and cemented with Panavia 21 cement. Differences in axial surface roughness had no effect on the marginal seating of the complete metal crowns.     

Precision of fit: the Procera AllCeram crown

STATEMENT OF PROBLEM: Strength, color stability, and precision of fit are requirements for all-ceramic restorations. The Procera AllCeram crown system, composed of a densely sintered high-purity alumina core combined with a low fusing surface porcelain, appears to satisfy most of these requirements. However, evaluation of marginal fit has not been reported. PURPOSE: This study measured the precision of fit of the Procera AllCeram crown fabricated with Procera CAD/CAM technology for the premolar and molar teeth fit to a die. MATERIAL AND METHODS: Five ivorine maxillary first premolars and first molars were prepared for full-coverage crowns. Preparations were standardized with a convergence angle of 10 degrees, chamfer margins of 1.3 to 1.5 mm circumferentially, and occlusal reduction of 2.0 mm. AllCeram crowns were fabricated for the dies, and the fit of the crown to the die was determined by using a standardized procedure with a silicone impression material that served a dual role: (1) as a retrievable luting agent, and (2) to replicate the internal aspects of the crown. Laser videography was used to measure the gap dimension between the crowns and the dies at the marginal opening, the axial wall, the cusp tip, and the occlusal adaptation measurement locations. Mean gap dimensions and standard deviations (SDs) were calculated for marginal opening, internal adaptation, and precision of fit. RESULTS: Mean gap dimensions and standard deviations at the marginal opening for the premolar and molar crowns were 56.0 microns SD +/- 21 and 63.0 microns SD +/- 13 microns, respectively. The mean gap dimensions and SDs of the internal adaptation were 69.0 microns SD +/- 17 microns for axial wall, 48.0 microns SD +/- 12 microns for cusp tip, and 36.0 microns SD +/- 7 microns for occlusal adaptation for the premolar crowns; and 49.0 microns SD +/- 3 microns axial wall, 67.0 microns SD +/- 21 microns cusp tip, and 74.0 microns SD +/- 29 microns occlusal adaptation for molar crowns. Precision of fit and SDs for premolar and molar crowns were 52.0 microns SD +/- 19 microns and 63.0 microns SD +/- 20 microns, respectively. Mean marginal openings and precision of fit gap dimensions for the crown groups were not significantly different at the .05 level. However, gap dimensions that defined the internal adaptation at the measurement locations were different (P < or = .05). CONCLUSION: Mean gap dimensions for marginal openings, internal adaptation, and precision of fit for the crown groups were below 70 microns. These findings show that the crowns studied can be prescribed with confidence knowing that the precision of fit will consistently be less than 70 microns.     

Effect of dynamic loading methods on cement film thickness in vitro

PURPOSE: Reduced cement flm thicknesses can improve crown seating and decrease marginal discrepancies. Improved marginal adaptation has the potential to reduce plaque accumulation, periodontal disease, and cement dissolution. Studies have indicated that dynamic seating methods can reduce seating discrepancies associated with zinc phosphate and resin cements. However, other types of cements and other dynamic techniques have not yet been studied or compared, nor has the mechanism for improved seating been fully explained. Therefore, the purpose of this study was to investigate the effect of a variety of loading methods on the film thicknesses of current types of crown and fixed partial denture cements compressed between glass plates. MATERIALS AND METHODS: This study investigated the effect of three dynamic loading methods on film thickness of six representative fixed prosthodontic cements. These included zinc phosphate, resin-modified glass ionomer, encapsulated glass ionomer, adhesive composite resin, composite resin, and polycarboxylate. The method was derived from American Dental Association specifications for cement film thickness. In control groups, the cements were placed between two glass glass plates and statically loaded with a 15-kg weight. The test groups were initially similarly loaded, and then for 30 seconds further subjected to simulated repeated patient opening and closing, vibrations from an electromallet, or an ultrasonic device. RESULTS: Mean film thicknesses ranged from 7.4 micrometers for polycarboxylate / ultrasound up to 40.3 micrometers for composite resin / static. Two-way analysis of variance revealed that the effects of material type and cementation method and their interaction all significantly affected film thickness (P < .0001). Multiple range analysis showed that dynamic methods were generally superior to static loading and that the ultrasonic method was the best overall. CONCLUSIONS: The different dynamic loading methods all significantly decreased cement film thicknesses between glass plates. The ultrasonic method was the most effective. The type of cement used also influenced film thickness. Composite resins were more affected than other materials.     

The effect of adhesive luting agent-dentinal surface interactions on compressive strength of two types of all-ceramic crowns

This research compared the compressive strength of two types of all-ceramic crown (Hi-Ceram and Duceram) as affected by selected luting cements (Zn phosphate, glass ionomer and composite resin cement). Thirty crowns of similar size and shape were constructed (15 crowns of each tested material) to fit a standard posterior tooth preparation. Five crowns from each material were cemented by one of the tested cements. The cemented crowns were loaded until catastrophic failure. A two-way analysis of variance was performed and showed that the type of utilized cement had a significant effect on the compressive strength being that Panevia Ex. resin cement the most effective one followed by glass ionomer and then finally zn phosphate cement. Statistical analysis also showed that Hi-Ceram crowns were more resistant to occlusal load than Duceram.     

The fracture resistance of all-ceramic crowns on supporting structures with different elastic moduli

This in vitro study evaluated the fracture resistance of all-ceramic crowns as a function of the elastic modulus of the supporting die. All-ceramic crowns were made for dies with three different elastic moduli and two different crown lengths. The occlusal surface was loaded in compression with a 12.7-mm steel ball. The fracture load increased markedly with the increase in elastic modulus. The largest increase was seen when only the occlusal surface of the crown was covered. The characteristic fracture load of the complete-crown restorations was more than double that of the occlusal-cover restorations in the dies with the lowest modulus of elasticity, while for the dies with the highest modulus of elasticity the difference in the characteristic fracture load for the two configurations was not significant.     

The relationship between abutment taper and resistance of cemented crowns to dynamic loading

This study investigated the relationship between abutment total occlusal convergence angle (taper) and the resistance of cemented crowns subjected to dynamic loading. Crown and abutment analogs were placed using zinc-oxide-eugenol, zinc-phosphate, glass-ionomer, or resin composite cement. Total occlusal convergence angles of 2.5, 5, 10, 15, 20, 30, and 40 degrees were used. Dynamic stresses were applied to the luted components until the bond failed or the components reached 10(6) load cycles. The data were analyzed using the staircase technique. The relationship between convergence and resistance was approximately linear for all the cements tested. Crowns luted with resin composite cement were more resistant to dynamic lateral loading than those placed using glass-ionomer or zinc-phosphate cements. Crowns luted with zinc-oxide-eugenol cement presented the least resistance to cyclic lateral stresses.     

Marginal discrepancy of all-ceramic crowns cemented on implant abutments

PURPOSE: The purpose of this investigation was to determine the mean marginal discrepancy of all-ceramic crowns cemented on implant abutments. MATERIALS AND METHODS: Five Br?nemark CeraOne abutments were connected to implant fixtures embedded in acrylic resin blocks. The marginal discrepancy was measured using a video camera connected to a digitizing board at four locations on each abutment for five samples in each of the following groups: all-ceramic caps (caps), all-ceramic crowns (crowns), and all-ceramic crowns cemented with zinc phosphate cement (cemented crowns). RESULTS: The mean marginal discrepancies were as follows: caps, 99.0 micrometers (SD, 16); crowns, 117.8 micrometers (SD, 20); and cemented crowns, 168.8 micrometers (SD, 23). Statistically significant differences were found between all three groups at the 99% level of confidence. In addition there were two significant differences between abutments. CONCLUSIONS: Subgingival marginal discrepancies of the magnitude measured in this study have been shown to cause periodontal problems. It is probable that the marginal discrepancy of CeraOne restorations, as tested, can be improved. Efforts should be made to enhance the marginal accuracy of these restorations.     

Retention of paraposts cemented with dentin-bonded resin cements

The main purpose of this study was to assess the retention of Paraposts cemented with dentin-bonded resin cements in single-rooted teeth with elliptical canals. Forty-two mandibular premolars and canines were used in this study. The crowns of these teeth were removed 1 mm above the cementoenamel junction and the root canals instrumented to a depth of 8 mm to receive size 5 Paraposts. Prepared teeth were divided into six equal groups. Each group was assigned to a different cementation system at random. The six cementation systems used were: Fleck's Cement, Universal Post Cementation Kit, Prisma Universal Bond 3/Biomer, Scotchbond 2/Resiment, All-Bond 2/All-Bond C & B Cement, and Scotchbond Multi-Purpose/Resiment. Following post cementation, the teeth were stored in water at 37 degrees C for 24 hours, after which the posts were subjected to uniaxial tensile force on a testing machine until post separation occurred. Paraposts cemented with Prisma Universal Bone 3/Biomer or with Scotchbond Multi-Purpose/Resiment had significantly greater separation forces than posts cemented with any of the other cementation systems. Adhesive failure of the posts occurred in all of the specimens of the resin cement groups, whereas cohesive failure of the cement occurred in the majority of the specimens of the zinc phosphate cement group. The effects of thermocycling and post length (5 mm versus 8 mm) on the retention of Paraposts cemented with dentin-bonded resin cements were also investigated. Neither thermocycling nor post length had a significant effect on post separation force.     

Long term clinical evaluation of three luting materials

A last critical step in the completion of a cast restoration is permanent cementation. With the development of new luting agents the practitioner has to be aware of the physical and biological properties as well as the long term clinical performance of these materials. In this study three commonly used luting agents were evaluated over a four year period. The three cements, a zinc phosphate, a glass ionomer and a resin cement were tested for their reaction to periodontal tissues, pulpal response and other clinical parameters. In twenty six patients, 61 crowns, onlays or bridge abutments were cemented. Evaluations were made at 0 hour, after 7 days, 6 and 12 months and 4 years. In general the cements performed satisfactorily. Health of periodontal tissues adjacent to the crowns improved considerably after 7 days. Postcementation hypersensitivity appeared to be a negligible problem, which was attributed to the time span between preparation and cementation, which exceeded in most instances four weeks. The choice of a final luting agent should be based on anticipated postoperative pulpal reactions, rather than exclusive reliance on physical properties.     

Marginal fit consistency of copy-milled all-ceramic crowns during fabrication by light and scanning electron microscopic analysis in vitro

The aim of this study was to evaluate the marginal fit of copy-milled Celay In-Ceram crowns after different fabrication steps and to compare light-microscopic with scanning-electron-microscopic data. A master steel die of an upper middle incisor with a shoulder preparation and a rounded inner line angle was used. Impressions were taken to produce 10 working stone dies. One crown per working die was manufactured. The evaluation of the external marginal gap was performed on the master steel die by using a light microscope and a computerized video image analysis system after copy milling (A), glass infiltration (B), and veneering (C). Approximately 3900 readings were taken. In a final series the veneered crowns were measured by using a scanning electron microscope (Cs), yielding approximately 1000 readings. The results obtained were: A mean, 25.1 microm; s.d., 5.1 microm; range, 2.5-76.8 microm: B mean, 20.6 microm; s.d., 2.3 microm; range, 2.5-76.1 microm: C mean, 18.3 microm; s.d., 4.1 microm; range, 2.5-87.2 microm: Cs mean, 23.0 microm; s.d., 7.6 microm; range, 0.0-94.5 microm. The results were statistically evaluated using the t-test. The differences found between the series did not show practical relevance. Therefore, it is concluded that the manufacturing steps after copy milling have no obvious influence on the external marginal gap width. Scanning electron microscopic data seem to confirm the light-microscopic results. Hence, we expect that the Celay In-Ceram method yields a clinically acceptable marginal fit.     

Fracture resistance of endodontically treated roots after restoration

This study evaluated the shear strength resistance of endodontically treated roots that were restored by two different techniques. Twenty-seven recently extracted single-rooted teeth with similar anatomic characteristics were sectioned to obtain the same length for all specimens. Group I (GI) consisted of 14 roots restored with cast post-core (nickel-chromium alloy) and cemented using zinc phosphate cement; group II (GII) consisted of 13 roots restored with steel prefabricated posts (FKG) cemented with zinc phosphate cement and rotated with caution for anchorage. The crown portion of this group was made using a hybrid composite resin (Prisma APH). Results showed that on all specimens of GI the fracture occurred in the cervical root structure while in GII the composite resin fractured in all specimens. Statistical analysis showed a significantly higher resistance to fracture for GI than GII. The specimens were sectioned longitudinally for stereoscopic microscope analysis (63x) and did not show fracture lines in the dentin anchorage post area for any of the specimens.     

Circadian rhythm of breath hydrogen in young women

PURPOSE: The retention forces of a newly developed compomer cement (Dyract Cem), a glass ionomer cement (Ketac Cem Aplicap), and a resin cement (F21) were examined. MATERIAL AND METHODS: Cemented cast gold crowns were removed along the path of insertion with a Zwick universal testing device. The impact of both a cured and a noncured additional bonding layer that were applied to the inner surface of the crowns was examined across the Dyract Cem group. RESULTS: The mean adhesive strength was measured at 2.36 +/- 0.69 N/mm2 in the Ketac Cem group, at 0.60 +/- 0.28 N/mm2 in the F21 group, and at 1.85 +/- 0.94 N/mm2 in the Dyract Cem group, respectively. The application of an additional bonding layer to the inner surface of the crowns did not significantly improve the retentive strength of Dyract Cem; the respective mean strengths were observed at 1.46 +/-0.33 N/mm2 for the uncured and at 1.70 +/- 0.76 N/mm2 for the cured bonding layers. CONCLUSIONS: Dyract Cem and Ketac Cem showed significantly higher retentive strengths than F21 (p < 0.001, Wilcoxon test, 5% level). No significant difference was found in bond strength between Ketac Cem and Dyract Cem.     

New players and puzzles in the Hedgehog signaling pathway

STATEMENT OF PROBLEM: Esthetic demands of patients and practitioners for an all-ceramic crown in both anterior and posterior regions of the dental arches has prompted the development of the Procera AllCeram crown. Long-term clinical trials that evaluate the strength and naturalness of the Procera AllCeram crown are lacking. PURPOSE: This prospective study was initiated to evaluate the clinical performance of 100 Procera AllCeram crowns after 5 years in service. MATERIAL AND METHODS: One hundred Procera AllCeram crowns were fabricated for 58 patients (20 men and 38 women). Patients were treated by 4 general dental practitioners. Crown placement involved both the anterior and posterior regions of the dental arches. Crowns were examined at baseline and once a year during the 5 years that followed and evaluated at each appointment with the California Dental Association's quality assessment system. RESULTS: Of the 97 crowns remaining in the study after 5 years, only 3 crowns had experienced a fracture through the veneering porcelain and the aluminum oxide coping material. Two additional crowns were replaced as a result of fractures of only the veneering porcelain. One crown was replaced as a result of recurrent caries. All remaining crowns were ranked as either excellent or acceptable for surface/color, anatomic form, and marginal integrity. CONCLUSION: The 5-year clinical observations and ranking with the California Dental Association's quality assessment criteria supported the conclusion that Procera AllCeram crowns may be used in all areas of the mouth.     

Changes in esophageal function after vertical banded gastroplasty as demonstrated by esophageal scintigraphy

STATEMENT OF PROBLEM: Earlier studies on orthodontic brackets have shown a loss of bond strength after a sonic toothbrush was used. PURPOSE: This in vitro study evaluated the difference in bond strength of single complete veneer crowns after being subjected to the equivalent of 2 years of brushing with sonic and counterrotational toothbrushes. MATERIAL AND METHODS: Complete gold crowns were fabricated with a conventional indirect technique for 30 extracted, intact, prepared human premolar teeth. Castings were then luted to the teeth with glass ionomer cement. Teeth were randomly divided into 3 groups of 10 teeth each, 1 group to be brushed with Sonicare sonic toothbrush, 1 group to be brushed with Interplak counterrotational mechanical toothbrush, and 1 group as the control. Groups 1 and 2 were then brushed for the equivalent of 2 years per tooth. A uniform force of 50 g for the sonic toothbrush and 120 g for the counterrotational toothbrush was used. Control specimens were not brushed. Brush heads and sample teeth in contact with the toothbrush were kept moist at all times. Tensile dislodgment force was determined with an Instron universal testing machine. RESULTS: The castings brushed with a sonic toothbrush required a mean of 43.22 kg (+/- 11.16) force to remove the crowns from the teeth, whereas the counterrotational group required a mean of 42.87 kg (+/- 10.42) and the control group a mean of 42.12 kg (+/- 6.61). Analysis of variance on the force data indicated no differences among the 3 groups in the force needed to remove the castings (F[2,24] = 0.031, P = .97). CONCLUSION: This in vitro study demonstrated no significant differences between groups in the amount of tensile dislodgment force required to remove cemented full veneer crowns from prepared teeth after brushing for the equivalent of 2 years time with a sonic toothbrush or a counterrotational toothbrush.     

Doubly shrink fitted dies: optimisation by analytical and FEM calculations

Abstract

In some powder metallurgy part forming, when high compacting loads would require a too large single shrink fitted die, or the inner die diameter is very large but the compaction area is modest, twice shrink fitted dies, which are relatively expensive and complex to build, should be used. In both cases, at any given compacting load, the design should minimise dimensions and stresses. The design targets are minimum die size, optimum intermediate diameter and optimum interference, with maximum stresses on each die item lower than those allowable for the selected materials. In dual mode, for fixed overall dimension, intermediate diameters and shrink fitting interference should enable to maximise the compacting load without exceeding the allowable maximum stresses. In the first part of this work, for cylindrical shapes (circular profile dies) and axisymmetric plane stress problems, dimensions, interferences and stress–strain states have been analytically calculated to optimise doubly shrink fitted dies in the abovementioned sense. In the second part, the same evaluations for axisymmetric generic problems have been carried out by finite element method (FEM) approach integrated in an optimisation procedure. The minimum overall dimensions of the die are presented as a function of the ratio between applied load and maximum allowable stress. Corresponding interferences and optimum diameters have been calculated. Some approximate equations for a quick and handy optimisation are presented. The differences between analytical and numerical results obviously depend on the consideration of the actually stressed length, or compact height, and total die height. The comparison indicates that FEM analyses are needed since analytical calculations generally give low approximations, especially for some die geometries.     

Use of plastic bar molded casting in the modification of variably expanding investment to compensate for casting shrinkage of nickel-chromium alloy

Trial plastic bar molded castings were compared for accuracy with cast crowns by means of a nickel-chromium alloy, which was used to establish the liquid density of variably expanding investments. The plastic bars were invested to evaluate the change of expansion rate in a wide range of six liquid densities from 0% to 100%, and the distances between the sections were measured before and after casting. Wax crowns were cast to obtain a more detailed relation around 0% expansion at seven liquid densities, and the gaps between the base of the die and the margin of the crown were measured before and after casting. The expansion rates of both castings were calculated and thus were proportional to the liquid density; both regression curves indicated high correlation coefficients. As a result of the statistics of the Student's t-test, the difference between the two methods was not significant. The trial plastic bar was useful in establishing the variably expanding investment for precise casting of artificial crowns.     

Clinical commissioning of Laitinen Stereoadapter for fractionated stereotactic radiotherapy

PURPOSE: The purpose of this study was to investigate the distribution of shades selected for metal ceramic crowns provided at a dental teaching hospital. MATERIALS AND METHODS: Data on the selection of shade for 2,500 metal ceramic crown units, placed over a 5-year period at the University Dental Hospital of Manchester, were collected and analyzed. Only those crowns placed adjacent to minimally restored vital teeth were included in the study. RESULTS: The results indicate that the most frequently chosen shades were in the mid-range of reddish-brown hue. Furthermore, shades in the reddish-grey range of hue were rarely chosen. The selection of more than one shade for a crown ("mixed shades") was generally restricted to the maxillary anterior teeth. CONCLUSION: Knowledge of the distribution of shades selected for permanently luted metal ceramic crowns may be a useful adjunct in shade selection, particularly for the inexperienced operator.     

Impact of Converging Chute Walls for Roller Compacted Concrete Stepped Spillways

A study utilizing a three-dimensional, 1:22 scale, physical model was conducted to evaluate the flow characteristics in the spillway with varying training wall convergence angles. The wall height required to contain the flow for conditions tested varied from critical depth at a 15° convergence angle to three times the critical depth at a 52° convergence angle. The results of the study may be used to estimate minimum training wall height for conditions where bulking due to air entrainment may reasonably be neglected.     

Microleakage of endodontically treated teeth restored with posts

A fluid filtration system using 15 psi of pressure on the penetrating fluid was used to quantify the amount of microleakage of a stainless-steel post and a carbon-fiber post system, each placed with various cements. Statistical analysis showed that there was a significant difference in microleakage between the cements (p < 0.001). Zinc phosphate cement showed the most microleakage, whereas C & B Metabond cement showed the least. There was no significant difference in microleakage between the stainless-steel and carbon-fiber posts. The results of this study showed that both posts, when cemented with dentin-bonding resin cements (C & B Metabond and Panavia-21), exhibited less microleakage than when cemented with non-dentin-bonding cements (glass ionomer and zinc phosphate).