Optical properties and structure of R2O–Ga2O3–SiO2 and RO–Ga2O3–SiO2 glasses

Refractive index and molar refraction of Li₂O–, Na₂O–, CaO–, and BaO–Ga₂O₃–SiO₂ glasses have been used to test the validity of a structural model of silicate glasses containing Ga₂O₃ glasses. Ga₂O₃ enters these types of glass in a similar manner as Al₂O₃. It is assumed that, for (SiO₂/Ga₂O₃) >1 and (Ga₂O₃/R₂O) ≤1, Ga₂O₃ associates primarily with modifier oxides to form GaO₄ units. The rest of modifier oxide forms silicate units with non-bridging oxygen ions. Silicate structural units have the same factors as found for binary alkali- and alkaline earth silicate glasses. Differences between experimental and model values suggest another structure for (Ga₂O₃/SiO₂) ≥1.     

Densification and dielectric properties of SrO–Al2O3–B2O3 ceramic bodies

The influence of SrO (0·0–5·0 wt%) on partial substitution of alpha alumina (corundum) in ceramic composition (95 Al₂O₃–5B₂O₃) have been studied by co-precipitated process and their phase composition, microstructure, microchemistry and microwave dielectric properties were studied. Phase composition was revealed by XRD, while microstructure and microchemistry were investigated by electron-probe microanalysis (EPMA). The dielectric properties by means of dielectric constant (ε _r ), quality factor (Q × f) and temperature coefficient of resonant frequency (τ _f ) were measured in the microwave frequency region using a network analyser by the resonance method. The addition of B₂O₃ and SrO significantly reduced the sintering temperature of alumina ceramic bodies to 1600 °C with optimum density (∼ 4g/cm³) as compared with pure alumina powders recycled from Al dross (3·55g/cm³ sintered at 1700 °C).     

Synthesis and properties of magnetic solid superacid: SO4/ZrO2–B2O3–Fe3O4

A magnetic SO₄²⁻/ZrO₂–B₂O₃–Fe₃O₄ solid superacid catalyst is prepared via a simple chemical co-precipitation approach. The obtained materials were characterized in detailed by X-ray powder diffraction, thermogravimetric analysis–different scanning calorimetry, Fourier transform infrared spectroscopy (FTIR), electron microscopy (SEM and TEM), and Mossbauer spectra. Powder X-ray diffraction patterns show that in this composite oxide the transformation temperature of ZrO₂ from tetragonal to monoclinic phase is higher compared to the pristine SO₄²⁻/ZrO₂ material. The introduction of Fe₃O₄ endows the superacid with a super-paramagnetic property while in a ferromagnetic state after calcination. The superacid exhibits high catalytic activity in forming ethyl acetate by esterification.     

Crystallization and magnetic properties of a 10Li2O–9MnO2–16Fe2O3–25CaO–5P2O5–35SiO2 glass

The crystallization behavior and magnetic properties of 10Li₂O–9MnO₂–16Fe₂O₃–25CaO–5P₂O₅–35SiO₂ (10LFS) glass have been studied using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), transmission electron microscopy (TEM) and selected area electron diffraction (SAED) to observe the crystallization behavior and a superconducting quantum interference device (SQUID) for measurements of the magnetic properties. The DTA shows that the 10LFS glass has one broad exothermic peak at approximately 674 °C and one sharp (the highest) exothermic peak at 764 °C. When the 10LFS glass crystallized at 850 °C for 4 h, the crystalline phases identified by XRD were lithium silicate (Li₂SiO₃), β-wollastonite (β-CaSiO₃), lithium orthophosphate (Li₃PO₄), magnetite (FeFe₂O₄) and triphylite (Li(Mn_0.5Fe_0.5)PO₄). The SEM surface analysis revealed that the β-wollastonite and lithium silicate have a lath morphology. The TEM microstructure examination showed that the largest FeFe₂O₃ particles have a size of approximately 0.3 μm. When the 10LFS glass was heat treated at 850 °C for 16 h and a magnetic field of 1000 Oe was applied, a very small remnant magnetic induction of 0.01 emu g⁻¹ and a coercive force of 50 Oe were obtained, which revealed an inverse spinel structure.     

Dielectric properties and microstructure of TiO2 modified (ZnMg)TiO3 microwave ceramics with CaO–B2O3–SiO2

The low-fired (ZnMg)TiO₃–TiO₂ (ZMT–TiO₂) microwave ceramics using low melting point CaO–B₂O₃–SiO₂ as sintering aids have been developed. The influences of Mg substituted fraction on the crystal structure and microwave properties of (Zn_1−x Mg _x )TiO₃ were investigated. The result reveals that the sufficient amount of Mg (x ≥ 0.3) could inhibit the decomposition of ZnTiO₃ effectively, and form the single-phase (ZnMg)TiO₃ at higher sintering temperatures. Due to the compensating effect of rutile TiO₂ (τ_f = 450 ppm/°C), the temperature coefficient of resonant frequency (τ_f) for (Zn_0.65Mg_0.35)TiO₃–0.15TiO₂ with biphasic structure was adjusted to near zero value. Further, CaO–B₂O₃–SiO₂ addition could reduce the sintering temperature from 1150 to 950 °C, and significantly improve the sinterability and microwave properties of ZMT–TiO₂ ceramics, which is attributed to the formation of liquid phases during the sintering process observed by SEM. The (Zn_0.65Mg_0.35)TiO₃–0.15TiO₂ dielectrics with 1 wt% CaO–B₂O₃–SiO₂ sintered at 950 °C exhibited the optimal microwave properties: ε ≈ 25, Q × f ≈ 47,000 GHz, and τ_f ≈ ± 10 ppm/°C.     

Synthesis and properties of glasses in the K2O–SiO2–Bi2O3–TiO2 system and bismuth titanate (Bi4Ti3O12) nano glass–ceramics thereof

Glasses were prepared by the melt-quench technique in the K₂O–SiO₂–Bi₂O₃–TiO₂ (KSBT) system and crystallized bismuth titanate, BiT (Bi₄Ti₃O₁₂) phase in it by controlled heat-treatment at various temperature and duration. Different physical, thermal, optical, and third-order susceptibility (χ³) of the glasses were evaluated and correlated with their composition. Systematic increase in refractive index (n) and χ³ with increase in BiT content is attributed to the combined effects of high polarization and ionic refraction of bismuth and titanium ions. Microstructural evaluation by FESEM shows the formation of polycrystalline spherical particles of 70–90 nm along with nano-rods of average diameter of 85–90 nm after prolonged heat treatment. A minor increase in dielectric constants (ε_r) has been observed with increase in polarizable components of BiT in the glasses, whereas a sharp increase in ε_r in glass–ceramics is found to be caused by the formation of non-centrosymmetric and ferroelectric BiT nanocrystals in the glass matrix.     

Low-Magnetoresistance RuO2–Al2O3 Thin-Film Thermometer and its Application

Thermometers consisting of RuO₂–Al₂O₃ composite thin films were prepared by RF sputtering. It was found that different electrode-patterning techniques have dissimilar effects on the magnetoresistance (MR) and the temperature coefficient of resistance (TCR). In general, the thermometers with electrodes fabricated by photo-resist lithography exhibit superior performance compared to those with electrodes prepared using a metal mask. By adjusting the relative compositions of RuO₂ and Al₂O₃, the thermometers can be applied to a wide temperature range from 60 mK to 500 K. In a pulsed magnetic field up to 55 T, the MR at 4.2 K of a typical thermometer for the temperature range from 1.4 K to 300 K increases linearly with magnetic field to a maximum of ~15 %, corresponding to a temperature deviation of ~−4 %. As frequency increases from dc to 1.9 MHz, the MR decreases from  −13 % to ~ − 0.5 % at T = 1.3 K and H = 55 T. By integrating the thermometer with a heater on a sapphire chip, a micro-calorimeter can be developed and successfully used to measure the heat capacity of small mg-sized sample. The RuO₂–Al₂O₃ composite film can also be employed as an infrared bolometer operated at room temperature.     

Magnetoelectric and electrical properties of WO3-doped (Ni0.8Zn0.1Cu0.1)Fe2O4/[Pb(Ni1/3Nb2/3)O3–Pb(Zn1/3Nb2/3)O3–PbTiO3] composites

A total of 5 mol% WO₃-doped (1−x)(Ni_0.8Zn_0.1Cu_0.1)Fe₂O₄/xPb(Ni_1/3Nb_2/3)O₃–Pb(Zn_1/3Nb_2/3)O₃–PbTiO₃ ((1−x)NZCF/xPNN-PZN-PT) magnetoelectric particulate ceramic composites were prepared by conventional solid-state reaction method via low-temperature sintering process. X-ray diffraction (XRD) measurement and scanning electron microscopy (SEM) observation indicate that piezoelectric phase and ferrite phase coexist in the sintered particulate ceramic composites. Dielectric property of the (1−x)NZCF/x0.53PNN–0.02PZN–0.05Pb(Ni_1/2W_1/2)O₃–0.40PT ((1−x)NZCF/xPNN-PZN-PNW-PT, nominal composition) composites is improved greatly as compared to that of the undoped (1−x)NZCF/xPNN-PZN-PT composites. The WO₃-doped (1−x)NZCF/xPNN-PZN-PT composites exhibit typical P–E hysteresis loops at room temperature accompanied by the decrease of saturation polarization (P _s) and remnant polarization (P _r). At the same time, piezoelectric property of the composites deteriorates greatly with the increase of ferrite content. The (1−x)NZCF/xPNN-PZN-PNW-PT composites can be electrically and magnetically poled and exhibit apparent magnetoelectric (ME) effect. A maximum ME voltage coefficient of 13.1 mV/(cm Oe) is obtained in the 0.1NZCF/0.9PNN-PZN-PNW-PT composite at 400 Oe d.c. magnetic bias field superimposed 1 kHz a.c. magnetic field with 5 Oe amplitude. The addition of WO₃ in the piezoelectric phase decreases sintering temperature greatly from 1180 °C to 950 °C and decreases dielectric loss sharply of the composites, thus the ME voltage coefficient increases. Such ceramic processing is valuable for the preparation of magnetoelectric particulate ceramic composites with excellent ME effect.     

Relaxation process in PbI2–Ag2O–V2O5–B2O3 system: Dielectric,AC conductivity and modulus studies

Silver ion conducting super-ionic glass system xPbI₂–(100 − x) [Ag₂O–2(V₂O₅–B₂O₃)], where, 5 ≤ x ≤ 25, were prepared via melt quenching route and -characterized by XRD and DSC. Their electrical properties were measured by impedance spectroscopy in the frequency range of 2 MHz to 20 Hz from 30 to 120 °C. The electrical relaxation mechanism has been studied using AC conductivity, dielectric modulus function and frequency dependent dielectric permittivity over a wide range of frequency and temperature. Two different scaling approaches for AC conductivity as well as dielectric permittivity spectra were used to understand the nature of relaxation processes.     

Structure and electrical conductivity relaxation studies of Nb2O5-doped B2O3–Bi2O3–LiF glasses

Glasses with composition (70 − x) B₂O₃·15Bi₂O₃·15LiF·xNb₂O₅ with x = 0–1.0 mol% were prepared by conventional glass-melting technique. The molar volume V _m values decrease and the glass transition temperatures T _g increase with increase of Nb₂O₅ content up to 0.2 mol%, which indicates that Nb⁵⁺ ions act as a glass former. Beyond 0.2 mol% Nb₂O₅ the V _m increases and the T _g decreases, which suggests that Nb⁵⁺ ions act as a glass modifier. The FTIR spectra suggest that Nb⁵⁺ ions are incorporated into the glass network as NbO₆ octahedra, substituting BO₄ groups. The temperature dependence of the dc conductivity follows the Greaves variable range hopping model below 454 K, and follows the small polaron hopping model at temperatures >454 K. σ _dc, σ _ac conductivity and dielectric constant (ε) decrease and activation energy for dc conduction ΔE _dc which increases with increasing Nb₂O₅ content up to 0.2 mol%, whereas σ _dc, σ _ac and (ε) increase and ΔE _dc decreases with increasing Nb₂O₅ content beyond 0.2 mol%. The impedance spectroscopy shows a single semicircle or arcs which indicate only the ionic conduction mechanism. The electric modulus formalism indicates that the conductivity relaxation is occurring at different frequencies exhibit temperature-independent dynamical process. The (FWHM) of the normalized modulus increases with increase in Nb₂O₅ content suggesting that the distribution of relaxation times is associated with the charge carriers Li⁺ or F⁻ ions in the glass network.     

Thermal properties and crystallization of PbO–MoO3–P2O5 glasses

Thermal properties and crystallization of glasses from PbO–MoO₃–P₂O₅ ternary system were studied in three compositional series (100 − x)[0.5PbO–0.5P₂O₅]–xMoO₃ (A), 50PbO–yMoO₃–(50 − y)P₂O₅ (B), and (50 − z)PbO–zMoO₃–50P₂O₅ (C). Glass transition temperature, crystallization temperature, coefficient of thermal expansion, and dilatation softening temperature of the studied glasses were determined by differential thermal analysis and dilatometry. Crystallization products of annealed glass samples were investigated by X-ray diffraction and Raman spectroscopy. X-ray diffraction analysis of crystallized glasses revealed the formation of PbP₂O₆, Pb₃P₄O₁₃, and PbMoO₄ in the samples of the B series. In the series A and C in the samples with a high MoO₃ content, crystalline compounds of Pb(MoO₂)₂(PO₄)₂ and (MoO₂)(PO₃)₂, respectively, were identified. Raman spectra of crystalline samples confirmed the results of X-ray diffraction measurements and provided also information on thermal stability of glasses and formation of glass-crystalline phases in the studied glass series.     

Investigation on the phase stability,sintering and thermal conductivity of Sc2O3–Y2O3–ZrO2 for thermal barrier coating application

Rare earth oxides co-doped zirconia have been developed for application in thermal barrier coating systems to promote the performance and durability of gas turbines. 8 mol%Sc₂O₃, 0.6 mol%Y₂O₃–stabilized ZrO₂ (ScYSZ) powder was synthesized by chemical co-precipitation method. The phase stability, sintering resistance and thermo-physical properties of ScYSZ and 8 wt%Y₂O₃ stabilized ZrO₂ (8YSZ) were investigated. The results indicated that both ScYSZ and 8YSZ show single tetragonal phase before heat treatment. After heat treating at 1500 °C for 300 h, ScYSZ exhibits excellent phase stability with 100% metastable tetragonal (t′) phase, whereas the content of monoclinic phase in 8YSZ reached 49.4 mol%. ScYSZ also exhibits higher sintering resistance and lower thermal conductivity than 8YSZ. ScYSZ can be considered to be explored as candidate material for TBC application.     

Wetting and interfacial interactions in the CaO–Al2O3–SiO2/silicon carbide system

In this article, the wetting of 23 wt% CaO–15 wt% Al₂O₃–62 wt% SiO₂ molten glass on polycrystalline silicon carbide is studied under air at temperatures between 1,100 and 1,590 °C. Wetting experiments are performed by the sessile drop technique. Good wetting (final contact angle lower than 50°) is observed regardless of the experimental temperature when it is higher than 1,300 °C. Moreover, some specific experiments of wetting of glass on platinum, silica and monocrystalline SiC substrates are also performed. The character of molten glass spreading on silicon carbide (reactive or non-reactive) as well as the role of the atmosphere on interfacial interactions with SiC are identified and discussed.     

Glass formation and third-order optical nonlinear characteristics of bismuthate glasses within Bi2O3–GeO2–TiO2 pseudo-ternary system

Glass-forming region of Bi₂O₃–GeO₂–TiO₂ (BGT) pseudo-ternary system was determined by using melt-quench method. A series of high transparent glass samples were selected and their structural characteristics were investigated by FT-IR and Raman spectra. By employing Z-scan and optical Kerr shutter techniques with femtosecond laser pulses as excitation source, third-order optical nonlinearities (TON) of the BGT glasses as well as the TON response time were investigated at wavelength of 800 nm. The ultrafast nonlinear response and high figure of merit suggest great potentials of BGT glasses in applications of all-optical switching or related optical devices.     

Preparation and characterization of Y2O3–Sm2O3 co-doped ceria electrolyte for IT-SOFCs

Y₂O₃–Sm₂O₃ co-doped ceria (YSDC) powder was synthesized by a gel-casting method using Ce(NO₃)₃·6H₂O, Sm₂O₃ and Y₂O₃ as raw materials. Phase structure of the synthesized powders was characterized by X-Ray diffraction analysis. Sinterability of the powders was investigated by testing the relative density and observing the microstructure of the sintered YSDC samples. Electrical conductivity of the sintered YSDC samples was measured using impedance spectra method. Single solid oxide fuel cells based on the YSDC electrolyte were also assembled and tested. The results showed that YSDC powders with single-phase fluorite structure can be obtained by calcining the dried gelcasts at temperature above 800 °C. Average particle size of the YSDC powder is 50–100 nm. Relative density of more than 95% of the theoretical can be achieved by sintering the YSDC compacts at temperature above 1400 °C. The sintered YSDC sample has an ionic conductivity of 4.74 × 10⁻² S cm⁻¹ at 800 °C in air. Single fuel cells based on the YSDC electrolyte with 50 μm in thickness were tested using humidified hydrogen as fuel and air as oxidant, and maximum power densities of about 190 and 112 mW cm⁻² were achieved at 700 and 600 °C, respectively.     

Giant electrical conductivity enhancement in BaO–V2O5–Bi2O3 glass by nanocrystallization

The effects of the annealing of 20BaO–30V₂O₅–50Bi₂O₃ glass on the structural and electrical properties were studied by scanning electron micrographs (SEM), X-ray diffraction (XRD), differential scanning calorimeter (DSC) density (d) and dc conductivity (σ). The XRD and SEM observations have shown that the sample under study undergoes structural changes: from amorphous at the beginning, to partly crystalline after nanocrystallization at crystallization temperature (T_c) for 1 h and to colossal crystallization after the annealing at the same temperature for 24 h. The average size of these grains after nanocrystallization at T_c for 1 h was estimated to be about 25–35 nm. However, the glass heat treated at T_c = 580 °C for 24 h the microstructure changes considerably. The nanomaterials obtained by nanocrystallization at T_c for 1 h exhibit giant improvement of electrical conductivity up to four order of magnitude and better thermal stability than the as-received glass. The major role in the conductivity enhancement of this nanomaterial is played by the developed interfacial regions “conduction tissue” between crystalline and amorphous phases, in which the concentration of V⁴⁺–V⁵⁺ pairs responsible for electron hopping is higher than inside the glassy matrix. The annealing at T_c for 24 h leads to decrease of the electronic conductivity. This phenomena lead to disappearance of the abovementioned “conduction tissue” for electrons and substantial reduction of electronic conductivity. The high temperature (above θ/2) dependence of conductivity could be qualitatively explained by the small polaron hopping (SPH) model. The physical parameters obtained from the best fits of this model are found reasonable and consistent with the glass compositions.     

Microstructures formed during devitrification of Na2O·Al2O3·B2O3·SiO2·Fe2O3 glasses

Soda alumina borosilicate glasses of composition (24-y)Na₂O·yAl₂O₃·14B₂O₃·37SiO₂·25Fe₂O₃, y = 8, 12, 14, 16 mol%, were melted using Fe₂O₃ as raw material. Besides, samples with y = 12 and Fe₂O₃ concentrations of 14.32, 17.8, and 25.0 mol% were prepared from FeC₂O₄·2H₂O as raw material. The X-ray diffraction analyses showed the presence of magnetite for the samples from all the investigated compositions. Transmission electron microscopy (TEM) evidenced that all the samples are phase separated and droplets in the diameter range 100–1000 nm, enriched in iron, are formed. Inside these droplets, numerous small magnetite particles, with size in the 25–40 nm interval, are crystallized.     

Highlighting of structural units of B2O3–Li2O–P2O5 system under heat treatment

As technology evolves towards the design of small size – high efficiency devices there is a necessity for the development of solid, stable electrolytes that can be fabricated in various shapes. Accordingly, a glass system of xB₂O₃·0.4Li₂O·(0.6 − x)P₂O₅ with 0 ≤ x ≤ 0.6 mol%, was prepared by melting the raw materials at 1200 °C and rapidly cooling the melts at room temperature. The samples were afterwards heat treated to develop crystalline structures, for better identification of the units that build up the network.     

Bi2O3助熔剂对CaO-B2O3-SiO2/Al2O3玻璃陶瓷复合材料性能的影响

以CaO-B₂O₃-SiO₂(CBS)玻璃粉体和Al₂O₃陶瓷粉体为原料,通过在CBS与Al₂O₃的质量比固定为50:50的玻璃-陶瓷复合材料中添加适量的Bi₂O₃作为烧结助熔剂,探讨了Bi₂O₃助熔剂对CBS/Al₂O₃复合材料的烧结性能、介电性能、抗弯强度和热膨胀系数的影响规律.研究表明:Bi₂O₃助熔剂能通过降低CBS玻璃的转变温度和黏度促进CBS/Al₂O₃复合材料的致密化进程,于880 ℃下烧结即能获得结构较致密、气孔较少的CBS/Al₂O₃复合材料.然而,过量添加Bi₂O₃将使玻璃的黏度过低,从而恶化CBS/Al₂O₃复合材料的烧结性能、介电性能及抗弯强度.当Bi₂O₃的添加量为CBS/Al₂O₃复合材料的1.5wt%时,于880 ℃下烧结即能获得最为致密的CBS/Al₂O₃复合材料,密度为2.82 g·cm^-3,这一材料具有良好的介电性能(介电常数为7.21,介电损耗为1.06×10^-3),抗弯强度为190.34 MPa,0~300 ℃的热膨胀系数为3.52×10^-6 K^-1.