共查询到19条相似文献,搜索用时 218 毫秒
1.
一、不完全齿轮机构的应用范围 图1所示的不完全齿轮机构是由渐开线齿轮机构演变而成的一种间歇传动机构。即在主动齿轮上做出一个或几个齿,并根据运动时间与停歇时间的要求,在从动轮上做出与主动轮相啮合的齿间,同时在从动轮停歇期内,两轮轮缘还需配置锁止弧,其作用在于停歇期内定位,以防止从动轮的游动。由于该机构具有结构简单的优点,所以常用于轻载、低速和具有特殊运动要求的专用机器中。如机械压力机的送料进给运动,半自动车床中四工位工作台的间歇转位运动、铣削乒乓球拍周缘的专用靠模铣床、蜂窝煤饼压机工作台的间歇转位运动等。然… 相似文献
2.
不完全摩擦轮间歇运动机构及设计武汉水利电力大学章琴心某些机械在工作过程中,常常需要执行机构按一定规律运动和停歇.如送进运动、进料运动、成品输送运动等等.间歇运动机构的作用正是在机械设备中将连续运动转化为周期性的运动和停歇,所以间联运动机构是自动线、半... 相似文献
3.
《现代制造技术与装备》2015,(4)
不完全齿轮机构是将主动轮的等速连续转动转换为从动轮的规律间歇转动。从动轮的动停比不受机构结构的限制,制造方便,但是每次间歇运动的开始和结束都会产生冲击,故不完全齿轮机构一般只用于低速,轻载及机构冲击不影响正常工作的场合[1]。为了改善不完全齿轮的传动性能,使其能适用于较高速的场合,在不完全齿轮的基础上装配缓冲凸轮机构。通过对应用于常见分度机构的不完全齿轮及其缓冲凸轮的设计,利用Pro/E参数化建模和ADAMS仿真,验证了其作为间歇机构的运动特性,并且对比了不完全齿轮机构在有无缓冲装置前后传动特性的变化。 相似文献
4.
在实现间歇运动的不完全齿齿轮机构中,主动齿轮是个不完全齿齿轮,从动齿轮是个正常齿轮。由主动齿轮连续转动来实现间歇运动。主动齿轮的第一个齿和最后一个齿与从动齿轮的啮合情况不同于其它齿相啮合的情况,其实际啮合线更长一些,这就导致了不完全齿齿轮机构设计中的一些新问题。本文对实现间歇运动的不完全齿齿轮传动进行了分析,提供了可行的设计方法。 相似文献
5.
通过对间歇机构——不完全齿轮机构的研究,解决了运输机械的货物准确定位、垂直上升运动和水平运动的连续供货问题,其结果具有新颖性和实用性。 相似文献
6.
介绍一种简易的不完全齿轮机构 总被引:1,自引:0,他引:1
介绍一种简易的不完全齿轮机构陈安岳(华东船舶工业学院工厂镇江212003)不完全渐开线齿轮机构能将主动轮的等速连续运动转换成从动轮的间歇运动。其动与停的时间比不受机构结构的限制,制造也较方便,用于某种特定的场合,能充分体现它的优越性。我们研制的一台端... 相似文献
7.
8.
笔者在设计“管道冷压合口安装机”时,设计了一套不完全齿轮间歇差动机构(以下简称“间歇差动机构”)。此机构是不完全齿轮间歇运动机构和齿轮差动机构的混合机构,结构简单紧凑,工作可靠。间歇差动机构的结构简图如图1所示。其结构主要由输入轴1、齿轮2、3、4,扇齿轮5及棘爪6所组成。其动作原理如下: 经减速后的旋转运动输入轴1,带动齿轮2和4低速旋转,齿轮2与大齿轮3常啮合,齿轮4与扇齿轮5间歇性啮合。扇齿轮5的轮廓空套在大齿轮3的内腔中,其接合面上设置棘爪机构6。当齿轮4与扇齿轮5啮合脱开后,由棘爪机构带动扇齿轮5随齿轮3同步旋转到下次啮合,当齿轮4与扇齿轮5啮合时, 相似文献
9.
由三个齿轮和四连杆组成的简单机构,可以为像分度工作台之类的自动化生产设备产生间歇运动。辅助传动齿轮安装在本机构的输入轴和驱动电机之间。可把工作台调到要求的速度。同样,齿轮机构安装在本机构输出轴和分度工作台之间,可以确定工作台每旋转一次要求停留的次数。因为机构所有的齿轮。总是处于啮合状态,机构输入轴以匀速旋转时,输出轴却产生均匀的加速运动和均匀的减速运动。 相似文献
10.
胡秉辰 《机械工人(冷加工)》1994,(9):2-3
分度凸轮机构概述 自动机和自动生产线上大量应用间歇机构(分度机构)。传统的间歇机构有槽轮、棘轮和不完全齿轮机构。这些机构分度精度不高,性能差,只能用于低速,每分钟分度几次至几十次。随着生产节拍的加快和高精度分度的需要,国外生产线上大量采用凸轮式 相似文献
11.
12.
13.
14.
《机械工程学报(英文版)》2010,(5)
An intermittent connection is one of the major problems that affect the network reliability and communication quality.However,little attention has been paid to the detection,analysis and localization of the intermittent connections.Partially due to the limitations of the DeviceNet protocol,there is no effective online diagnostic tool available to identify the location of intermittent connection.On the basis of different DeviceNet fault scenarios induced by intermittent connections,a new graph-based diagnostic method is developed to analyze DeviceNet fault patterns,identify the corresponding fault scenarios,and infer the location of the intermittent connection problem by using passively captured network faults.A novel error source analysis tool,which integrates network data-link layer analysis and feature based network physical layer information,is developed to restore the snapshots of the network communication at each intermittent connection induced error.A graph based location identification method is developed to infer the location of the intermittent connections based on the restored error patterns.A 3-node laboratory test-bed,using master-slave polling communication method,is constructed to emulate the intermittent connection induced faults on the network drop cable by using digital switches,whose on/off states are controlled by a computer.During experiments,the network fault diagnosis is conducted by using information collected on trunk cable(backbone).Experimental study shows that the proposed method is effective to restore the snapshots of the network errors and locate the drop cable that experiences the intermittent connection problem. 相似文献
15.
A method is proposed for calculating tool-setup parameters in intermittent thread cutting such that tool life is extended. 相似文献
16.
分析了影响传动链系统间歇运动的动力学因素,讨论了传动链系统的动力学建模方法,建立了传动链系统动力学方程,然后采用模态叠加法求解方程。为了验证建模的准确性,以模切机间歇传动链系统为例,建立了动态实验装置,对链条间歇运动的动态特性进行了测试和分析。实验结果表明,提出的建模方法精度较高,为深入研究间歇传动链系统特性提供了依据。 相似文献
17.
18.
《机械制造与自动化》2016,(1)
介绍了间歇分度凸轮机构的分类及其基本工作原理与优缺点。针对PCB自动化检测设备,对间歇分度凸轮机构的选型设计进行阐述。选型采用经验设计法,主要考虑凸轮分割器在实际工作中转矩的大小。经设计计算所选择的凸轮分割器在实际工作中运转稳定,能实现所需的效率和精度要求,可为工程实际中间歇分度凸轮机构的选型提供指导。 相似文献
19.
《Flow Measurement and Instrumentation》2003,14(4-5):161-168
Two-phase horizontal intermittent flow in straight pipes is experimentally investigated. A new procedure is proposed to characterize the flow through the statistical analysis of the instantaneous cross-sectional averaged void fraction obtained by means of ring impedance probes. The algorithm, based on the statistical analysis of the void fraction records, allows the main intermittent flow parameters, such as slug frequency and length, time average void fraction, minimum and average liquid film height to be evaluated. The procedure is validated through flow visualizations, as obtained from a fast digital video camera.Experiments on air-water horizontal flows in 40 and 60 mm inner diameter pipes are performed. The operating conditions cover the 0.3–4.0 and 0.6-3.0 m/s gas and liquid superficial velocity ranges, respectively.An extensive comparison with literature data shows a general agreement with present measurement. The reliability of both the instrumentation and the signal analysis procedures allows new correlations for minimum and average liquid film height in stratified regions to be proposed. Finally proper dimensionless numbers were applied to correlate frequency data in a wide range of superficial velocity values. 相似文献