共查询到20条相似文献,搜索用时 93 毫秒
1.
提出了一种前置级采用两级串联固定阻尼孔的双喷嘴挡板水压伺服桥路模型,并对其进行了参量敏感性分析。探讨了喷嘴挡板位移、阀芯运动速度与阀芯两端压力的关系;运用正交设计方法研究了喷嘴直径、串联固定阻尼孔直径、阀芯直径及其运动速度、喷嘴挡板与喷嘴之间初始距离等参量对水压桥路特性的影响。结果表明,喷嘴直径以及喷嘴与挡板之间中位距离越小,阀芯与阀套之间配合间隙越大,阀芯直径越大,阀芯与阀套之间叠合长度越短,压力源压力越高,桥路控制的线性度越好;对于采用二级节流的水压伺服桥路,第一级固定阻尼孔直径越小,第二级固定阻尼孔直径越大,喷嘴前端流道直径越小,阀芯与阀套之间配合间隙以及阀芯直径越大,桥路响应就越快。这些研究结果为水压伺服阀样机的研制奠定了理论基础。 相似文献
2.
3.
双喷嘴挡板放大器是一种广泛应用的液压放大器,主要用作两级电液伺服阀的前置级,也用来制成单级伺服阀。目前电液伺服阀中的双喷嘴挡板放大器,一般都有回油节流孔。带回油节流孔的双喷嘴挡板放大器及其等效电路如图1所示。 相似文献
4.
5.
6.
两级电液伺服阀双喷嘴挡板阀内流场计算与分析 总被引:1,自引:0,他引:1
双喷嘴挡板阀是两级电液伺服阀的前置级,其结构参数对电液伺服阀的性能有着重要的影响。利用流场计算软件,对双喷嘴挡板阀的喷嘴在不同结构参数组合下的流场进行了计算,并分析了其液流特性,如速度特性、压力特性、流量特性等。研究表明:通过喷嘴挡板阀的流量随喷嘴直径、喷嘴端面直径和喷嘴外夹角的增大而增加,喷嘴挡板阀的压差却相应地减小;而喷嘴长度、喷嘴内夹角和腔内径对喷嘴各项性能影响不大。通过比较分析找到最佳结构参数组合,为双喷嘴挡板电液伺服阀喷嘴的工程设计提供理论依据和参考。 相似文献
7.
8.
9.
10.
喷嘴挡板伺服阀性能参数的研究 总被引:3,自引:0,他引:3
该文系统地研究了双喷嘴挡板电液伺服阀的工作原理和影响其性能的结构参数,建立了伺服阀结构参数数据库,并基于双喷嘴挡板伺服阀的数学模型开发了伺服阀面向结构参数的仿真平台.将应用软件MATLAB/Simulink进行动态仿真的结果与试验结果进行比较,验证了仿真平台的可行性.利用实验和仿真平台分析了影响伺服阀性能的主要参数. 相似文献
11.
12.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
13.
三爪自定心卡盘作为机床的主要附件,已有一百多年的发展历史,尽管目前随着数控技术的不断发展,越来越多地需求高速动力卡盘,但三爪自定心卡盘目前仍有一定的市场。 要保证卡盘可靠地夹紧工件,必须使其有可靠的夹持精度;要保持卡盘的精度,必须要严格控制各零部件公差及误差,如盘丝的极心偏。 极心偏是形成圆的渐开线的基圆圆心 (极心 )与盘丝内孔中心不同心所造成的偏差值。它对卡盘精度的影响分两种情况,一是卡爪夹持弧采用配磨,二是卡爪夹持弧采用单磨。本文主要探讨配磨时的影响。 卡爪夹持弧采用配磨,即每台卡盘整体… 相似文献
14.
15.
详细分析了圆柱面素线的直线度公差带在新旧标准中定义和解释的区别,并从对圆柱面素线实际要素检测的角度,提出了推行新标准的实际意义。 相似文献
16.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
17.
根据广州市珠江新城旅客自动运输系统(APM)列车的运行特点,介绍APM列车制动系统的制动方式及其特点,分析APM列车动态制动和摩擦制动的工作机理及其区别和联系,阐明APM列车制动系统的电控制过程和气控制过程,从而为APM列车制动系统的维护和管理提供一定的依据. 相似文献
18.
我公司于80年代末引进Aspera公司年产80万台冰箱(冷柜)压缩机生产线及软件技术,在压缩机加工中,活塞销孔(如图1所示)的加工是难点之一。用镗床加工,质量一直难以达到要求,废品率很高。后来我们将Aspera公司的加工工艺即精镗后滚光改为精镗后用金刚石铰刀粗、精铰孔,由此解决了这个技术难题。(1)原意大利Aspera公司工艺简述其工艺流程为:钻6.5通孔→扩孔至7+0.1→粗镗7.473+0.036、圆柱度0.01→精镗至7.935+0.006、圆柱度0.002→滚光7.938+0.006、圆柱度0… 相似文献
19.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
20.
The article presents a brief review of the wear models based on the kinetic thermofluctuation approach. The materials were developed using SamGTU sclerometric programming software and a set of instruments developed at Samara Engineering University for assessing the parameters of kinetic thermoactivation for surface fracture deformed by friction. The first obtained results of assessments and the estimated prediction of wear resistance exemplified by tribocouple of the aircraft chassis are presented. 相似文献