智利纪行

智利以铜著称,是中国铜业关注的地方.尽管北京与智利首都圣地亚哥的距离是全球各国首都之间最远的两个点,但还是有一批又一批的考察团远渡重洋来到这个神秘的国度. 2008年4月,我随山东方圆集团组成的考察组从北京启程,经过两次转机与航行到达地球另一面的圣地亚哥.这是一次行程长达两万多公里,历时近36个小时,横跨了欧亚大陆、穿越非洲大陆、掠过大西洋、赤道线和南美洲的漫长旅行,再加上智利境内的考察航程,往返的行程累计起来可以绕地球一周了!     

阿基米得螺线系数选择对模拟钛弯管推扩成形的影响

采用MSC公司的Superform软件对不同阿基米得螺线系数下的热推扩进行了模拟.扩径段采用了3种不同的系数并分析了不同系数下对热推扩成形弯管的影响.结果表明:扩径变形段中心轴线采用曲率半径渐变的阿基米得螺线,有利于管坯凹面金属充分向凸面流动,避免了传统弯曲变形内侧受压增厚,外侧受拉减薄;阿基米得螺线系数a≤0.9时,环向厚度差大;a≥l.3时,容易出现起皱和45°剪切变薄.本试验范围内,a值取1.0最佳.     

国外废金属的主要分布区域

国外废金属主要分布在工业发达国家.按产生分布地区划分,大体可分为北美地区(美国、加拿大),欧洲地区(欧共体),东南亚地区(日本、韩国、台湾),俄罗斯及澳洲几大部分.     

调解的精髓在于双赢——中国国际商会调解中心为再生企业排忧解难

1987年,伴随着国际贸易、国际投资和国际经济合作业务的持续增长,各种商事纠纷和贸易摩擦的不断增加,中国贸促会成立了第一家商事调解机构--北京调解中心2000年北京调解中心正式更名为中国贸促会/中国国际商会调解中心. 中国贸促会/中国国际商会调解中心秉承"以和为贵"、"促进双赢"的调解理念,以调解的方式,独立公正地帮助中外当事人解决了大量的商事争议,成为中国商事调解领域一支最重要的社会力量.其现有中外籍在册调解员300 余名,有41家贸促会系统地方调解中心遍布在全国各地,形成了一个庞大的调解网络.整个调解网络的受案量已达 6 000余件,调解成功率达到80%.调解当事人涉及50多个国家和地区.     

梦醒在开始的地方再生产业从风雨迷茫中一路走来

资源再生、循环经济在今天可谓风光无限:国家大力提倡,企业日益重视,再生产业吸引了全社会的目光.但在从新中国成立到改革开放后二十年的时间里,资源再生还是一个没有独立构成的行业,从业人员也往往因为每天与"破烂"为伍而被人看不起.     

2007年中国机床工具行业十大新闻

1. 中央和地方省市主要领导频繁视察机床行业企业,国家为数控机床产业发展创造了空前良好的发展环境. 胡锦涛、吴邦国、温家宝、贾庆林、李长春等党和国家领导人以及辽宁、黑龙江、山东、江苏、云南、湖北、广东、陕西、浙江、天津、重庆等省市主要领导相继视察了机床工具厂和数控系统厂.各级领导频繁视察,为数控机床产业的发展创造了空前良好的发展环境.     

透析营销失败的10大原因

经验主义,没有创新 　　一些企业或个人成功后,总是喜欢用过去的思路经营新的品种.殊不知任何新品都有差异性,他们的消费对象、产品的核心卖点及表现力均是不同的,经验主义很容易使产品销售走弯路,甚至导致营销失败.作为老产品,包装也要常更新,但要沿袭原有的核心记忆点与要素,才能使市场趋于稳定,甚至增长.……     

亚熔盐法回收赤泥

采用亚熔盐法对赤泥中的Al2O3和Na2O的回收进行研究.实验第一步通过采用亚熔盐和添加适量石灰乳液回收赤泥中的Al2O3,使其中Al2O3的含量降至4.19%,Al2O3单程回收率达88%;实验第二步采用低浓度的NaOH溶液对赤泥进行深度脱钠,使得最终赤泥中Al2O3和Na2O的含量分别降到3.88%和1.39%,Al2O3/SiO2和Na2O/ SiO2相应降到0.17和0.06;经过回收Al2O3和Na2O后的终赤泥呈现出表面疏松多孔的颗粒状形貌.本研究在较低温的条件下综合回收赤泥中的Al2O3和Na2O.     

灰铸铁主要元素变量三角试片白口宽度与抗拉强度数学模型的研究

在进行灰铸铁铸造生产时,通过不断采集同一浇包中铁液所浇注的三角试片白口宽度、主要化学成分及所浇注试棒的抗拉强度,在大量试验数据的基础上,逐渐摸索出三角试片白口的宽度和C、Si、Mn含量与其抗拉强度内在数量关系,用数学归纳法得出一个灰铸铁的主要元素C、Si、Mn三因素变量与三角试片白口宽度和抗拉强度的一次回归方程。借助回归方程能迅速地预测强度,指导配料,最大限度的降低铸件的成本。     

“表面工程行业清洁生产及节能减排新技术、新装备交流会”在北京召开

近日,北京表面工程学会在北航新主楼第八报告厅召开了“表面工程行业清洁生产及节能减排新技术、新装备交流会”,学会邀请了北京中如技术有限公司曹建岭高工和北京蓝丽佳美化工科技中心李家柱研究员作学术报告,交流会由北京表面工程学会理事长朱立群教授主持,学会理事及会员代表近40人出席.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.