Biosorption of Astrazone Blue basic dye from an aqueous solution using dried biomass of Baker's yeast

In this study dried biomass of Baker's yeast, Saccharomyces cerevisiae, is used as a sorbent for Astrazone Blue basic dye aqueous solution. Factors affecting the adsorption process: dye concentration, contact time, temperature and pH were investigated. The equilibrium concentration and the adsorption capacity at equilibrium were determined using three different sorption models namely: Langmuir, Freundlich and Temkin isotherms. It was found that increasing temperature and pH result in higher dye loadings per unit weight of the sorbent. The results gained from this study were described by Langmuir isotherm model better than Freundlich and Temkin isotherm models. The calculated heat of adsorption of the dye-yeast system indicates that the bio-sorption process is taking place by chemical adsorption and has an endothermic nature. The maximum adsorption capacity at 30 degrees C and pH 7 was calculated as 70 mg/g for dried biomass of Baker's yeast compared to 18.5mg/g for commercial granular activated carbon, indicating that dried biomass of Baker's yeast can be considered as a good sorbent material for Astrazone Blue solution.     

Adsorption of basic dyes from single and binary component systems onto bentonite: simultaneous analysis of Basic Red 46 and Basic Yellow 28 by first order derivative spectrophotometric analysis method

The present study deals with the simultaneous analysis and adsorption of Basic Yellow 28 and Basic Red 46 dyes in binary mixture onto bentonite. First order derivative spectrophotometric method was used for simultaneous analysis of BY28 and BR46 in binary mixtures. The adsorption experiments were carried out in a batch system. The mono- and multi-component Langmuir and Freundlich isotherm models were applied to experimental data and the isotherm constants were calculated for BY28 and BR46 dyes. The monolayer coverage capacities of bentonite for BY28 and BR46 dyes in single solution system were found as 256.4 mg/g and 333.3mg/g, respectively. It was observed that the equilibrium uptake amounts of BY28 and BR46 dyes in binary mixture onto bentonite decreased considerably with increasing concentrations of the other dye resulting in their antagonistic effect. The adsorption equilibrium data fitted more adequately to mono-component Langmuir isotherm model than mono-component Freundlich isotherm model, while the extended Freundlich isotherm model adequately predicted the multi-component adsorption equilibrium data at moderate ranges of concentration. Thermodynamic parameters showed that adsorption of BR46 and BY28 was endothermic and spontaneous in nature.     

Dye removal from wastewater using activated carbon developed from sawdust: adsorption equilibrium and kinetics

Mahogany sawdust was used to develop an effective carbon adsorbent. This adsorbent was employed for the removal of direct dyes from spent textile dyeing wastewater. The experimental data were analysed by the Langmuir and Freundlich models of adsorption. Equilibrium data fitted well with the Langmuir model. The rates of adsorption were found to conform to the pseudo-second-order kinetics with good correlation. The equilibrium adsorption capacity of the sawdust carbon was determined with the Langmuir equation as well as the pseudo-second-order rate equation and found to be >300 mg dye per gram of the adsorbent. The most ideal pH for adsorption of direct dyes onto sawdust carbon was found to be 3 and below. The results indicate that the Mahogany sawdust carbon could be employed as a low cost alternative to commercial activated carbon in the removal of dyes from wastewater.     

Kinetic and equilibrium studies on the removal of acid dyes from aqueous solutions by adsorption onto activated carbon cloth

Removal of acid dyes Acid Blue 45, Acid Blue 92, Acid Blue 120 and Acid Blue 129 from aqueous solutions by adsorption onto high area activated carbon cloth (ACC) was investigated. Kinetics of adsorption was followed by in situ UV-spectroscopy and the data were treated according to pseudo-first-order, pseudo-second-order and intraparticle diffusion models. It was found that the adsorption process of these dyes onto ACC follows the pseudo-second-order model. Adsorption isotherms were derived at 25 degrees C on the basis of batch analysis. Isotherm data were treated according to Langmuir and Freundlich models. The fits of experimental data to these equations were examined.     

Removal of Basic Red 46 dye from aqueous solution by adsorption onto Moroccan clay

In this study, Moroccan crude clay of Safi, which was characterized by X-ray diffraction, is used as adsorbent for the investigation of the adsorption kinetics, isotherms and thermodynamic parameters of the Basic Red 46 (BR46) in aqueous solutions at various dye concentrations, adsorbent masses and pH values. The results showed that the adsorption capacity of the dye increased by initial dye concentration and pH values. Two kinetic models (the pseudo-first-order and the pseudo-second-order) were used to calculate the adsorption rate constants. The adsorption kinetics of the basic dye followed pseudo-second-order model. The experimental data isotherms were analyzed using the Langmuir, Freundlich and Dubinin–Radushkevish equations. The monolayer adsorption capacity for BR46 dye is 54 mg/g of crude clay. Nearly 20 min of contact time was found to be sufficient for the dye adsorption to reach equilibrium. Thermodynamical parameters were also evaluated for the dye–adsorbent system and revealed that the adsorption process is exothermic in nature.     

Removal of rhodamine B from aqueous solution by adsorption onto sodium montmorillonite

The adsorption of rhodamine B dye was carried out using sodium montmorillonite clay. The effect of parameters such as pH, adsorbent dosage and initial dye concentration was studied. The Langmuir and Freundlich isotherm models were applied and the Langmuir model was found to best fit the equilibrium isotherm data. Langmuir adsorption capacity was found to be 42.19 mg/g. Kinetic data followed pseudo-second-order kinetics. Maximum color removal was observed at pH 7.0. The ΔG° value was found to be negative, the adsorption process was feasible. The results indicate that sodium montmorillonite clay can be used for the removal of basic dyes from aqueous solutions.     

The reuse of dried activated sludge for adsorption of reactive dye

Adsorption processes are alternative effective methods for removal of textile dyes from aqueous solutions. The adsorption ability of adsorbent affects by physico-chemical environment for this reason in this paper effect of initial pH, dye concentrations, temperature and dye hydrolyzation were determined in a batch system for removal of reactive dye by dried activated sludge. The Langmuir isotherm model was well described of adsorption reactive dye and maximum monolayer adsorption capacity (at pH 2) of activated sludge was determined as 116, 93 and 71mgg(-1) for 20 degrees , 35 degrees and 50 degrees C, respectively. Initial pH 2, 20 degrees C and 30min contact time are suitable for removal of reactive dyes from aqueous solutions. Activated sludge was characterized by FT-IR analysis and results showed that active sludge has different functional groups and functional groups of activated sludge are able to react with dye molecules in aqueous solution. The pseudo first-order, second-order and intraparticle diffusion kinetics were used to describe the kinetic data. The pseudo second-order kinetic model was fit well over the range of contact times and also an intra particle diffusion kinetic model was fit well but in the first 30min. The dye hydrolyzation was affected adsorption capacity of biomass and adsorption capacity of biomass decreased with dye hydrolyzation from 74 to 38mgg(-1).     

Study of Cu(II) biosorption by dried activated sludge: effect of physico-chemical environment and kinetics study

Biosorption is a recent technology used to remove heavy metal ions from aqueous solutions. The biosorption of copper ions from aqueous solution by dried activated sludge was investigated in batch systems. Effect of solution pH, initial metal concentration and particle size range were determined. The suitable pH and temperature for studied conditions were determined as 4.0 and 20 °C, respectively. The theoretical max biosorption capacity of activated sludge was 294 mg g⁻¹ at 20 °C for <0.063 mm particle size. The equilibrium data fitted very well to both Langmuir and Freundlich isotherm models. The pseudo first and second-order kinetic models were used to describe the kinetic data. The experimental data fitted to second-order kinetic model. The particle size and initial metal concentration were effected the biosorption capacity of dried activated sludge. An increase in the initial metal concentration increases of biosorption capacity, which also increases with decreasing particle size. Dried activated sludge has different functional groups according to the FT-IR results.     

Equilibrium and kinetic adsorption study of Basic Yellow 28 and Basic Red 46 by a boron industry waste

In this study, the adsorption characteristics of Basic Yellow 28 (BY 28) and Basic Red 46 (BR 46) onto boron waste (BW), a waste produced from boron processing plant were investigated. The equilibrium adsorption isotherms and kinetics were investigated. The adsorption equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that adsorption behavior of two dyes could be described reasonably well by a generalized isotherm. Kinetic studies indicated that the kinetics of the adsorption of BY 28 and BR 46 onto BW follows a pseudo-second-order model. The result showed that the BW exhibited high-adsorption capacity for basic dyes and the capacity slightly decreased with increasing temperature. The maximum adsorption capacities of BY 28 and BR 46 are reported at 75.00 and 74.73mgg(-1), respectively. The dye adsorption depended on the initial pH of the solution with maximum uptake occurring at about pH 9 and electrokinetic behavior of BW. Activation energy of 15.23kJ/mol for BY 28 and 18.15kJ/mol for BR 46 were determined confirming the nature of the physisorption onto BW. These results indicate that BW could be employed as low-cost material for the removal of the textile dyes from effluents.     

Kinetics and equilibrium studies for the adsorption of Acid Red 57 from aqueous solutions onto calcined-alunite

The adsorption of Acid Red 57 (AR57) onto calcined-alunite was examined in aqueous solution in a batch system with respect to contact time, pH and temperature. The first-order, pseudo-second-order kinetic and the intraparticle diffusion models were used to describe the kinetic data and the rate constants were evaluated. The experimental data fitted very well the pseudo-second-order kinetic model and also followed the intraparticle diffusion model up to 90 min. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were also determined. The equilibrium data are successfully fitted to the Langmuir adsorption isotherm. The Langmuir isotherm constant, K(L), was used to evaluate the changes of free energy, enthalpy and entropy of adsorption for the adsorption of AR57 onto calcined-alunite. The results indicate that calcined-alunite could be employed as low-cost material for the removal of acid dyes from textile effluents.     

Adsorption of direct dye on palm ash: kinetic and equilibrium modeling

Palm ash, an agriculture waste residue from palm-oil industry in Malaysia, was investigated as a replacement for the current expensive methods of removing direct blue 71 dye from an aqueous solution. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption. Equilibrium data fitted well with Freundlich model in the range of 50-600mg/L. The equilibrium adsorption capacity of the palm ash was determined with the Langmuir equation and found to be 400.01mg dye per gram adsorbent at 30 degrees C. The rates of adsorption were found to conform to the pseudo-second-order kinetics with good correlation. The results indicate that the palm ash could be employed as a low-cost alternative to commercial activated carbon.     

Removal of Acid Violet 17 from aqueous solutions by adsorption onto activated carbon prepared from sunflower seed hull

The adsorption of Acid Violet 17 (AV17) was carried out using various activated carbons prepared from sunflower seed hull (SSH), an agricultural solid waste by-product. The effect of parameters such as agitation time, initial dye concentration, adsorbent dosage, pH and temperature were studied. The Langmuir and Freundlich isotherm models were applied and the Langmuir model was found to best report the equilibrium isotherm data. Langmuir adsorption capacity was found to be 116.27 mg/g. Kinetic data followed pseudo-second-order kinetics. Maximum colour removal was observed at pH 2.0. It was observed that the rate of adsorption improves with increasing temperature and the process is endothermic. The adsorbent surface was analysed with a scanning electron microscope. The results indicate that activated sunflower seed hull could be an attractive option for colour removal from dilute industrial effluents.     

Chromium(VI) adsorption from aqueous solution by Hevea Brasilinesis sawdust activated carbon

Adsorption capacity of Cr(VI) onto Hevea Brasilinesis (Rubber wood) sawdust activated carbon was investigated in a batch system by considering the effects of various parameters like contact time, initial concentration, pH and temperature. Cr(VI) removal is pH dependent and found to be maximum at pH 2.0. Increases in adsorption capacity with increase in temperature indicate that the adsorption reaction is endothermic. Based on this study, the thermodynamic parameters like standard Gibb's free energy (DeltaG degrees ), standard enthalpy (DeltaH degrees ) and standard entropy (DeltaS degrees ) were evaluated. Adsorption kinetics of Cr(VI) ions onto rubber wood sawdust activated carbon were analyzed by pseudo first-order and pseudo second-order models. Pseudo second-order model was found to explain the kinetics of Cr(VI) adsorption most effectively. Intraparticle diffusion studies at different temperatures show that the mechanism of adsorption is mainly dependent on diffusion. The rate of intraparticle diffusion, film diffusion coefficient and pore diffusion coefficient at various temperatures were evaluated. The Langmuir, Freundlich and Temkin isotherm were used to describe the adsorption equilibrium studies of rubber wood sawdust activated carbon at different temperatures. Langmuir isotherm shows better fit than Freundlich and Temkin isotherm in the temperature range studied. The result shows that the rubber wood sawdust activated carbon can be efficiently used for the treatment of wastewaters containing chromium as a low cost alternative compared to commercial activated carbon and other adsorbents reported.     

The removal of basic dyes from aqueous solutions using agricultural by-products

The adsorption of two basic dyes, namely, Malachite Green and Methylene Blue onto both agricultural by-products (i.e. rice bran and wheat bran) has been investigated in this study. The adsorption of both basic dyes was solution pH-dependent. The kinetic experimental data were analyzed using four kinetic equations including pseudo-first-order equation, pseudo-second-order equation, external diffusion model and intraparticle diffusion model to examine the mechanism of adsorption and potential rate-controlling step. The best-fit equation was identified using normalized standard deviation. The Langmuir and Freundich isotherms were used to fit the equilibrium data and the results showed that the Langmuir isotherm exhibited a little better fit to the Methylene Blue adsorption data by both adsorbents while the Freundlich isotherm seemed to agree better with the Malachite Green adsorption. The Gibbs free energy changes at 20 degrees C were calculated and the obtained values supported the conclusion that two dyes molecules adsorbed by physical processes. The effects of particle size, adsorbent concentration and solution ionic strength on the adsorption of the two basic dyes were also studied.     

Low cost removal of reactive dyes using wheat bran

In this study, the adsorption of Reactive Blue 19 (RB 19), Reactive Red 195 (RR 195) and Reactive Yellow 145 (RY 145) onto wheat bran, generated as a by-product material from flour factory, was studied with respect to initial pH, temperature, initial dye concentration, adsorbent concentration and adsorbent size. The adsorption of RB 19, RR 195 and RY 145 onto wheat bran increased with increasing temperature and initial dye concentration while the adsorbed RB 19, RR 195 and RY 145 amounts decreased with increasing initial pH and adsorbent concentration. The Langmuir and Freundlich isotherm models were applied to the experimental equilibrium data depending on temperature and the isotherm constants were determined by using linear regression analysis. The monolayer covarage capacities of wheat bran for RB 19, RR 195 and RY 145 dyes were obtained as 117.6, 119.1 and 196.1 mg/g at 60 degrees C, respectively. It was observed that the reactive dye adsorption capacity of wheat bran decreased in the order of RY 145>RB 19>RR 195. The pseudo-second order kinetic and Weber-Morris models were applied to the experimental data and it was found that both the surface adsorption as well as intraparticle diffusion contributed to the actual adsorption processes of RB 19, RR 195 and RY 145. Regression coefficients (R2) for the pseudo-second order kinetic model were higher than 0.99. Thermodynamic studies showed that the adsorption of RB 19, RR 195 and RY 145 dyes onto wheat bran was endothermic in nature.     

生物膜吸附反应动力学模型与平衡模型的试验研究

采用复合式活性污泥-生物膜反应器,从动力学角度研究生物膜吸附反应动力学模型和吸附平衡模型,以掌握反应控制条件.结果表明,在t≤30min时生物膜的表面吸附阶段,且生物膜附着满足可逆动力学模型;准二级反应模型更能描述生物膜的吸附反应过程;Lang-muir吸附等温线比Freundlich能够更好地说明生物膜良好的吸附性能.     

Equilibrium and kinetic adsorption study of a cationic dye by a natural adsorbent--silkworm pupa

In this work the use of silkworm pupa, which is the waste of silk spinning industries has been investigated as an adsorbent for the removal of C.I. Basic Blue 41. The amino acid nature of the pupa provided a reasonable capability for dye removal. Equilibrium adsorption isotherms and kinetics were investigated. The adsorption equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that adsorption behavior of the dye could be described reasonably well by either Langmuir or Freundlich models. The characteristic parameters for each isotherm have been determined. The monolayer adsorption capacity was determined to be 555 mg/g. Kinetic studies indicated that the adsorption follows pseudo-second-order kinetics with a rate constant of 0.0434 and 0.0572 g/min mg for initial dye concentration of 200 mg/l at 20 and 40 degrees C, respectively. Kinetic studies showed that film diffusion and intra-particle diffusion were simultaneously operating during the adsorption process. The rate constant for intra-particle diffusion was estimated to be 1.985 mg/g min(0.5).     

Waste metal hydroxide sludge as adsorbent for a reactive dye

An industrial waste sludge mainly composed by metal hydroxides was used as a low-cost adsorbent for removing a reactive textile dye (Remazol Brilliant Blue) in solution. Characterization of this waste material included chemical composition, pH(ZPC) determination, particle size distribution, physical textural properties and metals mobility under different pH conditions. Dye adsorption equilibrium isotherms were determined at 25 and 35 degrees C and pH of 4, 7 and 10 revealing reasonably fits to Langmuir and Freundlich models. At 25 degrees C and pH 7, Langmuir fit indicates a maximum adsorption capacity of 91.0mg/g. An adsorptive ion-exchange mechanism was identified from desorption studies. Batch kinetic experiments were also conducted at different initial dye concentration, temperature, adsorbent dosage and pH. A pseudo-second-order model showed good agreement with experimental data. LDF approximation model was used to estimate homogeneous solid diffusion coefficients and the effective pore diffusivities. Additionally, a simulated real effluent containing the selected dye, salts and dyeing auxiliary chemicals, was also used in equilibrium and kinetic experiments and the adsorption performance was compared with aqueous dye solutions.     

Removal of anionic dyes from aqueous solutions by adsorption of chitosan-based semi-IPN hydrogel composites

Semi-IPN hydrogel composites for dye adsorption studies were prepared via photopolymerization of poly(ethylene glycol) (PEG) macromer and acrylamide (AAm) monomer in the presence of chitosan (CS). Swelling properties and kinetics of the hydrogel composites were investigated in aqueous solution and Acid Red 18 (AR 18) solution. The adsorption studies showed that the adsorption capacity for AR 18 increased with the increase of initial dye concentration and chitosan content in the hydrogels, but decreased with the increase of pH and ionic strength of dye solutions. Absorption kinetics of AR 18 followed pseudo second-order kinetic model at pH 2.0. The adsorption capacities for Acid Orange 7 (AO 7), Methyl Orange (MO) and Basic Violet 14 (BV 14) were also examined at pH 2.0, and the equilibrium adsorption data of AR 18, AO 7 and MO well fitted the Langmuir isotherm. The hydrogel composites could be potentially used as absorbents for anionic dye removal in wastewater treatment process.