Strain-promoted azide-alkyne cycloaddition “click” as a conjugation tool for building topological polymers

Strain-promoted azide-alkyne cycloaddition “click” reaction (SPAAC) was successfully used as a tool in synthesis of star polymers by grafting onto approach. The application of SPAAC method in star polymer synthesis was investigated for coupling reaction of the dibenzocyclooctyne (DIBO) end group of polystyrene (PS) and poly(ethylene glycol) (PEG) with coupling agents bearing 2, 3, or 4 azido groups. Firstly, well-defined linear DIBO-terminated PS was obtained by atom transfer radical polymerization (ATRP) of styrene using a DIBO containing ATRP initiator and linear DIBO-terminated PEG was obtained by terminal functionalization of PEG monomethyl ether (PEG-OH). Then a series of star PS and PEG bearing two, three and four arms were prepared respectively by subjecting SPAAC coupling reaction between the linear polymer-DIBO and the azido tethered core molecules at 30 °C without catalyst. The obtained star PS showed a well-defined structure after fractional precipitation to remove slightly excess linear polymers, and all the star polymers were characterized via Fourier transform infrared spectroscopy (FTIR), ¹H nuclear magnetic resonance spectroscopy (¹H NMR), size exclusion chromatography (SEC) and matrix-assisted laser desorption ionization-time-of-flight mass spectrometry (MALDI-TOF MS).     

Synthesis and thermally responsive characteristics of dendritic poly(ether-amide) grafting with PNIPAAm and PEG

A series of thermally responsive dendritic core-shell polymers were prepared based upon dendritic poly(ether-amide) (DPEA), modified with carboxyl end-capped linear poly(N-isopropylacrylamide) (PNIPAAm-COOH) or both PNIPAAm-COOH and carboxyl end-capped methoxy polyethylene glycol (PEG-COOH) in different ratios via an esterification process to obtain DPEA-PNIPAAm or DPEA-PNIPAAm-PEG. Their molecular structures were verified by gel permeation chromatography, and ¹H NMR and FTIR spectroscopy. The temperature-dependent characteristics study has revealed that DPEA-PNIPAAm exhibits a lower critical solution temperature (LCST) of about 34 °C, whereas DPEA-PNIPAAm-PEG polymers with the PNIPAAm/PEG ratio of about 1.0 and 0.4 possess about 36 °C and 39 °C, respectively, compared with 32 °C for homopolymer PNIPAAm. The critical aggregation temperature was investigated using fluorescence excitation spectrum of pyrene as a sequestered guest molecule based upon the sharp increase of the I₃₃₈/I₃₃₃ value.     

Controlled synthesis and characterizations of amphiphilic poly[(R,S)-3-hydroxybutyrate]-poly(ethylene glycol)-poly[(R,S)-3-hydroxybutyrate] triblock copolymers

Well-defined biodegradable amphiphilic triblock copolymers consisting of atactic poly[(R,S)-3-hydroxybutyrate] (PHB) and poly(ethylene glycol) (PEG) as the side hydrophobic block and middle hydrophilic block were synthesized via ring opening polymerization of (R,S)-β-butyrolactone from PEG macroinitiators and characterized using NMR, GPC, FT-IR, XRD, DSC and TG analyses. The controlled synthesis was made possible by the facile synthesis of pure PEG macroinitiators through a TEMPO-mediated oxidation. Constituting 40-70 wt% of the copolymer content, PHB blocks grown were amorphous while PEG formed crystalline phase when segment was sufficiently long. While hindering PEG crystallization, atactic PHB mixed well with amorphous PEG to give single T_g in all the copolymers. The copolymers exhibited two-step thermal degradation profile starting with PHB degradation from 210 to 300 °C, then PEG from 350 to 450 °C.     

Thermo-sensitive sol-gel transition of poly(depsipeptide-co-lactide)-g-PEG copolymers in aqueous solution

A series of biodegradable graft copolymers composed of poly(ethylene glycol) side-chains and a poly(depsipeptide-co-dl-lactide) backbone (PDG-dl-LA-g-PEG) were prepared as a novel thermo-gelling system. An aqueous solution of PDG-dl-LA-g-PEG (20 wt%) with a certain PEG length and composition showed instantaneous temperature-sensitive gelation at 33 °C. The sol-gel transition temperature (T_gel) could be controlled from 33 to 51 °C by varying the PEG length and compositions without a decrease in mechanical strength of the hydrogels. The 20 wt% hydrogel was eroded gradually in PBS at 37 °C for 60 days. This research provides a molecular design approach to create biodegradable thermo-gelling polymers with controllable T_gel and mechanical toughness.     

Dynamics of unentangled cyclic and linear poly(oxyethylene) melts

Monodisperse low-molecular-weight (400-1500 g/mol) cyclic poly(oxyethylene)s (CPOE)s were synthesized from linear dihydroxy-terminated poly(oxyethylene)s (LPOE)s. The self-diffusion, NMR spin-spin relaxation, and zero-shear viscosity of CPOE and LPOE, as well as linear dimethoxy-terminated poly(oxyethylene) (LPOEDE), were measured in the melt state. The self-diffusion coefficients measured at 56 °C were ordered in the following sequence: LPOEDE > CPOE > LPOE, which is in excellent agreement with NMR spin-spin relaxation and viscosity data. The slower motion of LPOE compared to LPOEDE was attributed to chain-end hydrogen bonding. Scaling relations with molecular weight and activation energies were reconciled with chain-end and topological effects.     

Preparation of star copolymers with three arms of poly(ethylene oxide-co-glycidol)-graft-polystyrene and investigation of their aggregation in water

The star graft copolymers with three arms composed of poly(ethylene oxide) (PEO) as main chain and polystyrene (PS) as side chains were prepared by sequential anionic ring-opening copolymerization of ethylene oxide and ethoxyethyl glycidyl ether (EEGE), and then atom transfer radical polymerization (ATRP) of styrene. The anionic ring-opening copolymerization of EO and EEGE was carried out using 2-ethyl-2-hydroxymethyl-1,3-propanediol as trifunctional initiator and diphenylmethyl potassium (DPMK) as deprotonating agent. The resulting three-arm star copolymer [poly(EO-co-EEGE)]₃ could be easily hydrolyzed to unmask the pendant hydroxyl groups without affecting the PEO chains. The switch from the first to the second mechanism was completed by the reaction of the multi-pendant hydroxyl groups of three-arm PEO chain with 2-bromoisobutyryl bromide. The obtained poly(ethylene oxide-co-2-bromoisobutyryloxyglycidyl ether), [poly(EO-co-BiBGE)]₃, was used as macroinitiators to initiate the polymerization of styrene in bulk at 90 °C by ATRP. The final products and intermediates were characterized by NMR, SEC and IR in detail. The amphiphilic star graft copolymers synthesized can form micelles in water. The critical micelle concentration (cmc) determined by fluorescence spectra was about 5 × 10⁻⁷ g/mL. Sphere micelles were observed by transmission electron microscopy (TEM) at low copolymer concentration (6 × 10⁻⁵ g/mL), but the micelle shape became irregular when the copolymer concentration increased to 6 × 10⁻⁴ g/mL.     

Synthesis,characterization and surface properties of star‐shaped polymeric surfactants with polyhedral oligomeric silsesquioxane core

Star‐shaped amphiphilic polymeric surfactants comprising a hydrophobic polyhedral oligomeric silsesquioxane (POSS) core and hydrophilic poly(ethylene glycol) (PEG) arms with various chain lengths are successfully synthesized using copper(I)‐catalysed azide–alkyne cycloaddition (CuAAC) click reaction. Their chemical structures and molecular characteristics are clearly confirmed using Fourier transform infrared and ¹H NMR spectroscopies and gel permeation chromatography, and no homopolymer is found after CuAAC click reaction. Aqueous solutions of these star‐shaped polymers have been investigated using atomic force and transmission electron microscopies and dynamic light scattering studies and it is found that they can self‐assemble into micelles. The sizes of the micelles can be adjusted by the length of the PEG arms, where longer chains not only lead to increased micelle sizes, but also reduce the contact angle values. Moreover, the melting points and root mean square roughness of the obtained star‐shaped polymers are slightly increased on increasing the chain length of the PEG arms. © 2017 Society of Chemical Industry     

Synthesis and characterization of four‐arm star‐shaped polymers and copolymers

Four‐arm star‐shaped polymers and copolymers were obtained by transition metal‐catalyzed atom‐transfer radical polymerization (ATRP). The polymers were characterized by FTIR and ¹H‐NMR spectroscopy. Gel permeation chromatography results indicated the formation of polystyrene and polystyrene‐block‐poly(methyl methacrylate) (PS‐b‐PMMA) arms with controlled molecular weights. In dilute solution, the linear polymers had higher inherent viscosities than star‐shaped ones. Thermogravimetric analysis showed a similar degradation mechanism for linear and star‐shaped polymers. Differential scanning calorimetry indicated the successful formation of diblock star‐shaped copolymers. Copyright © 2006 Society of Chemical Industry     

Colloidal gel from amphiphilic heteroarm polyelectrolyte stars in aqueous media

We report on the gelation capability of polystyrene/poly(2-vinyl pyridine) amphiphilic heteroarm polyelectrolyte stars in acidic salt-free aqueous media. The star polymers associate through hydrophobic interactions, by retraction of the stretched arms under no interdigitation conditions, in the dilute regime forming colloidal soft nanoparticles comprising about 6 stars, At concentrations significantly higher than the hydrodynamic overlap concentration (c > 40c^∗), the crowding of the colloidal nanoparticles drives a jamming transition, leading to a colloidal gel. The intermediate overlap regime (c^∗ < c < 40c^∗) is characterized by a significant compaction of the polyelectrolyte entities prior interdigitation and jamming.     

Studies on Permeation,Rejection, and Transport of Aqueous Poly(ethylene Glycol) Solutions using Ultrafiltration Membranes

Abstract

The permeate flux and retention of aqueous solutions of poly(ethylene glycols) (PEG) with different molecular weights ranging from 4000 to 35,000 Da have been investigated using various compositions such as 100/0, 90/10, 80/20, and 70/30 wt% of cellulose acetate (CA)/sulfonated poly(etheretherketone) (SPEEK) ultrafiltration blend membranes. The factors affecting the rejection rate and permeate flux such as molecular weight of PEGs, concentration of the solute, composition of the membranes, and transmembrane pressures have been studied. It is seen that the increase in the concentration of PEG results in the decreased permeate flux and increased rejection for increasing CA content in the membranes. A similar observation in the flux and rejection was made for increasing the molecular weight of PEGs. Further, the mass transfer, diffusion, and true retention coefficients of the solute have been studied with different operating variables like molecular weight and concentration of PEGs. An increase in the molecular weight of PEGs results in the decrease of mass transfer and diffusion coefficients and increase of the true retention coefficient. A reverse trend is observed with increasing concentrations of PEG.     

Synthesis, characterization and thermal properties of soluble aromatic poly(amide imide)s

Novel diamines such as N,N′-bis(aminoaryl)terephthalamido-2-carboxylic acids (BATCA), which contain primary amine, amide and carboxylic acid groups and are soluble in dilute aqueous NaOH solution, were synthesized by reacting aromatic diamines with trimellitic anhydride chloride in dimethylformamide. Poly(amide imide)s containing 3:1 ratio of amide:imide groups in the polymer chain were prepared by low temperature solution polymerization of BATCAs with isophthaloyl chloride or terephthaloyl chloride in dimethylformamide at 5-10 °C to form poly(amide amic acid)s, and followed by treating with a mixture of triethylamine and acetic anhydride. The PAIs were soluble in polar aprotic solvents like dimethylformamide, dimethylacetamide, dimethylsulphoxide and N-methylpyrrolidone, and have inherent viscosities in the range of 0.30-0.66 dL/g. The PAIs were characterized by IR, ¹H NMR and ¹³C NMR techniques. Thermogravimetric analysis (TGA) has shown that the initial decomposition temperatures of the polymers are in the range of 250-440 °C, depending upon the structures of diamine and diacid chloride. The glass transition temperatures of the PAIs are in the range of 128-320 °C. The IDT and T_g values of the polymers containing terephthaloyl unit are higher by about 20-40 °C than those of the polymers with isophthaloyl unit. BATCA could be utilized for the preparation of thin film composite membranes having PAA/PAI barrier layer on PES by in situ interfacial polymerization with IPC/TPC/TMC.     

Z-RAFT star polymerization of styrene: Comprehensive characterization using size-exclusion chromatography

Reversible addition-fragmentation chain transfer (RAFT) polymerizations of styrene in bulk at 80 °C using tri-, tetra-, and hexafunctional trithiocarbonates, in which the active RAFT groups are linked to the core via the stabilizing Z-group, were studied in detail. These Z-RAFT star polymerizations of styrene showed excellent molecular weight control up to very high monomer conversions and star sizes of more than 200 kDa. The application of high pressure up to 2600 bar was found to significantly increase the relative amount of living star polymer. Not even at very high monomer conversions and for large star molecules, a shielding effect of growing arms hampering the RAFT process could be identified. Absolute molecular weights of star polymers using a conventionally calibrated SEC setup were determined with high precision by using a mixture of linear and star-shaped RAFT agents. When using phenylethyl as the leaving R-group, well-defined star polymers that perfectly match the theoretical predictions were formed. However, when using benzyl as the leaving group, a pronounced impact of monomer conversion on the star polymer topology was observed and pure star polymers with the expected number of arms could not be obtained.     

Star-shaped condensation polymers: Synthesis,characterization, and blend properties

A series of ?-caprolactone linear and star polymers were prepared and characterized in order to determine the effect of the star architecture (i.e., star number and arm length) on the morphology of these semicrystalline polymers. A spherulitic morphology was found in all the polymers investigated. However, for six arm stars containing low degrees of polymerization, it appears that the star core dominates its morphological behavior (presumably due to its relatively high volume fraction). The star core effects, however, are markedly reduced in star polymers were the arms contain higher degrees of polymerization. The impact of the star core was further explored by investigating several poly(?-caprolactone) (PCL):styrene–acrylontrile copolymers (SAN) blends. In all instances, miscible blends were the result because a single compositionally dependent glass-transition temperature (T_g) was observed. A moderate elevation in the T_g of the star-shaped polymers does occur, however, compared to their linear analogs. This effect is presumably due to the inability of the SAN chains to completely mix with all segments of star structure. © 1993 John Wiley & Sons, Inc.     

Synthesis, characterization and ring-opening polymerization of a novel six-membered cyclic carbonate bearing pendent allyl ether group

A novel six-membered cyclic carbonate with pendent allyl ether group, 5-allyloxy-1,3-dioxan-2-one (ATMC), was synthesized from glycerol, and the corresponding polycarbonate, poly(5-allyloxy-1,3-dioxan-2-one) (PATMC) was further synthesized by ring-opening polymerization in bulk at 120 °C. Two kinds of catalyst, tin(II) 2-ethylhexanoate (Sn(Oct)₂) and immobilized porcine pancreas lipase on silica particles (IPPL), were employed to perform the polymerization. The structures of the novel monomer and the resulting functional polymers were confirmed by FTIR, ¹H NMR, ¹³C NMR, GPC and DSC. The molecular weight (M_n) of PATMC decreased rapidly with the increase of IPPL or Sn(Oct)₂ concentration. The highest molecular weight (M_n = 48,700 g/mol) of PATMC with the polydispersity of 1.31 was obtained at 0.1 wt% concentration of IPPL for 48 h. Postpolymerization oxidation reactions to epoxidize the unsaturated bonds of the PATMC were also achieved. The epoxide-containing polymers could afford facilities for further modification.     

Bio-based hyperbranched polyurethanes for surface coating applications

High performance vegetable oil based hyperbranched polymers are not only interesting but also very useful with respect to current scenario of advanced coating materials. So in the present study hyperbranched polyurethanes have been synthesized from the monoglyceride of Mesua ferrea L. seed oil, poly(?-caprolactone)diol, 2,4-toluene diisocyanate and glycerol without using any catalyst by a two-step one pot A₂ + B₃ approach. The linear analog (neglecting little possible branching due to different components of monoglyceride) of the hyperbranched polyurethane has also been prepared by the same method without using glycerol, just to compare with hyperbranched polymer. The formation of polymers was confirmed by FTIR, ¹H NMR, UV and SEM studies and measurements of hydroxyl value, solubility and viscosity. TGA results indicated the high thermal stability of hyperbranched and linear polymers (210–220 °C). The properties like tensile strength, impact strength, hardness, adhesion, flexibility, gloss, elongation at break and chemical resistance were influenced by the hard segment content of the polymers. The hyperbranched polyurethane with 30% hard segment content showed the optimum properties. The values of hydrodynamic diameter of hyperbranched polymers compared to the linear analog support the hyperbranched formation. Thus it confirms the formation of mechanically strong and thermally stable hyperbranched polyurethane coating materials from a vegetable oil.     

Incorporation of different crystallizable amide blocks in segmented poly(ester amide)s

High molecular weight segmented poly(ester amide)s were prepared by melt polycondensation of dimethyl adipate, 1,4-butanediol and a symmetrical bisamide-diol based on ε-caprolactone and 1,2-diaminoethane or 1,4-diaminobutane. FT-IR and WAXD analysis revealed that segmented poly(ester amide)s based on the 1,4-diaminobutane (PEA(4)) give an α-type crystalline phase whereas polymers based on the 1,2-diaminoethane (PEA(2)) give a mixture of α- and γ-type crystalline phases with the latter being similar to γ-crystals present in odd-even nylons. PEA(2) and PEA(4) polymers with a hard segment content of 25 or 50 mol% have a micro-phase separated structure with an amide-rich hard phase and an ester-rich flexible soft phase. All polymers have a glass transition temperature below room temperature and melt transitions are present at 62-70 °C (T_m,1) and at 75-130 °C (T_m,2) with the latter being highest at higher hard segment content. The two melt transitions are ascribed to melting of crystals comprising single ester amide sequences and two or more ester amide sequences, respectively. These polymers have an elastic modulus in the range of 159-359 MPa, a stress at break in the range of 15-25 MPa combined with a high strain at break (590-810%). The thermal and mechanical properties are not influenced by the different crystalline structures of the polymers, only by the amount of crystallizable hard segment present.     

Characterization of star-shaped poly(l-lactide)s by liquid chromatography at critical conditions

A series of linear and star-shaped poly(l-lactide)s (PLA's) have been prepared by living polymerization of l,l-dilactide (LA) and analyzed by liquid chromatography at critical conditions (LC-CC). For the analysis of the PLA's LC-CC conditions have been used corresponding to silica gel as the stationary phase and a mixture of 1,4-dioxane/n-hexane (56.25/43.75 by vol%) at 50 °C as the mobile phase. At the critical point of adsorption, a series of linear C₄H₉-PLA-OH's having molar masses (M_n) in the range from 2.3×10³ to 7.4×10⁴, prepared by ring-opening polymerization of LA initiated with Sn(OC₄H₉)₂ (THF, 80 °C), showed no dependence of the elution volumes on molar mass. In subsequent experiments, star-shaped PLA's bearing various numbers of PLA-OH arms (R-(PLA-OH)_x) have been prepared in a controlled synthesis starting from various polyols (R-(OH)_x) containing exclusively primary hydroxyl groups: diethyleneglycol (x=2), trimethylolpropane (x=3), di(trimethylolpropane) (x=4), dipentaerithritol (x=6), and poly(3-ethyl-3-hydroxymethyloxetane) (〈x〉=13.4) and LA monomer. As coinitiator/catalyst tin(II) octoate (Sn(Oct)₂) has been used (bulk polymerization, 120 °C). ¹H NMR analysis of the resulting star-shaped polymers revealed that all OH-groups in the polyols started growth of the PLA chains. The series of star-shaped PLA's have been analyzed by LC-CC as well as by two-dimensional (2D) chromatography (i.e. LC-CC versus size exclusion chromatography (SEC)) with regard to possible structural imperfections. It has been shown, that the LC-CC elution volumes of the resulting R-(PLA-OH)_x increase with the number of PLA-OH arms, allowing discrimination of the individual R-(PLA-OH)_x's in their mixture. An exponential increase of the retention volume as a function of the number of arms has been found. Eventually, LC-CC measurements of the elution volumes carried out for acetylated star-shaped PLA's (R(PLA-OOCCH₃)_x) have shown that for the interactions of the R-(PLA-OH)_x macromolecules with the column packing the hydroxyl end-groups are mostly responsible.     

Crisscross addition polymerization of alkyl aldazines and 1,4-phenylene diisocyanate

Crisscross addition polymerization of alkyl aldazines (i.e., acetaldehyde azine, propionaldehyde azine, and butyraldehyde azine (BuAz)) and 1,4-phenylene diisocyanate (Ph(IC)₂) was investigated under various conditions. The crisscross addition polymerizations in pyridine yielded polymers in higher yields. The polymers obtained in the present study exhibited very limited solubilities and contained fractions insoluble in conventional organic solvents. However, since the BuAz/Ph(IC)₂ polymers obtained at 24 and 48 h were soluble in pyridine, the M_w values for these polymers were determined to be 2.2 × 10³ and 4.4 × 10³, respectively, by small angle X-ray scattering. These data indicated that molecular weights of the pyridine-insoluble polymers were as high as or close to 10⁴. IR, ¹H NMR, and MALDI-TOF-MS data confirmed the formation of linear polymers by crisscross addition polymerization. Thermogravimetric analyses indicated that the polymers were considerably decomposed in the region of 300-400 °C, but the polymers exhibited residual weights of 15-25% even at 500 °C. Differential scanning calorimetry data indicated that glass transition temperatures for the polymers were higher than the onset of decomposition presumably because of the rigid backbone.     

pH-Controlled association of PEG-containing terpolymers of N-isopropylacrylamide and 1-vinylimidazole

Temperature- and pH-controlled association of terpolymers of N-isopropylacrylamide (NIPA) with 1-vinylimidazole (VI) and polyethylene glycol (PEG) has been investigated by light scattering and atomic force microscopy (AFM) in situ. The polymers contained 0-15 mol% VI and 0-2 mol% PEG. The phase transition temperatures (T_p) have been in the range of 32-45 °C and exhibited significant dependence on the pH of solution in the pH range between 5 and 8. The T_p of the polymers increased with increasing VI content and with decreasing pH, confirming major effect of VI ionization status on T_p. The presence of PEG grafts in the polymer structure had augmenting effect on the magnitude of pH-responsiveness and on the pH-independent colloidal stability of the polymer particles formed above T_p. Incorporation of VI into the polymer structure had similar, but pH-dependent effect on colloidal stabilization of the polymer particles. The size of the particles formed after the phase transition is driven by the association of the collapsed NIPA segments in the globule conformation and it decreased with decreasing pH. The phase transition temperature of the polymers could be adjusted to increase from temperatures below, to temperatures above body temperature upon decreasing pH from 7 to 6, suggesting that such polymers could provide a material platform for a variety of biomedical applications. AFM analysis in situ showed a fully reversible formation of particles in the solutions of the polymers above their T_p.     

Synthesis and Characterization of Dendritic Star Poly(L-Lactide)s

Summary Dendritic star poly(L-lactide)s (PLLAs) were prepared by ring opening polymerization using a hyperbranched aliphatic polyester as the core. The stars were characterized by gel permeation chromatography (GPC) and nuclear magnetic resonance spectroscopy (NMR). The result shows the star PLLAs have narrow molecular weight distribution and the length of arms can be well controlled in terms of the molar ratios of L-lactide to the initiator. The structure and thermal properties of the star polymers were investigated by means of X-ray diffraction (XRD) and differential scanning calorimetry (DSC). XRD shows that the formation of star structure does not alter the structure of crystal of PLLA. The results of DSC indicate that the glass transition temperature (T_g) and the crystallinity of the star polymers increased with increasing the lengths of arms. It is identified that the crystallization of PLLA was effectively suppressed by the formation of star topology.