共查询到20条相似文献,搜索用时 125 毫秒
1.
在论述气动凿岩机振动原理及振动频谱理论计算的基础上,对国内外的手持式和气腿式凿岩机的手柄振动加速度进行了测量分析。在空载和凿岩条件下,对这两类气动凿岩机的振动特性作了研究。 相似文献
2.
3.
国内在气动凿岩机具的设计与研制方面,多年一直采用经验设计方法,研制周期长,费用高,且难以达到产品性能优化的要求。近年来我们结合气动冲击器和凿岩机等产品设计,利用计算机辅助设计方法,根据设计的要求,由计算机提出不同的设计方案,从而优选出最佳的结构参数。YGZM-40型凿岩机是我国新型的导轨式 相似文献
4.
5.
众所周知,城市道路的交通噪声影响到了居民的工作、学习和生活的方方面面,在噪声敏感区的影响尤为严重。文章指出了我国城市噪声污染的现状,分析了道路交通污染给人们带来的危害,对噪声的产生原因进行分析并从噪声源、噪声传播途径和完善法律法规等方面介绍了如何降低道路交通噪声污染。 相似文献
6.
《Planning》2014,(28)
随着城市人口增加、车辆的迅速增加以及工业、建筑业的快速发展,城市噪声污染越来越严重,并与大气污染和水污染共同构成了城市的三大污染。噪声污染对城市居民的健康特别是听力健康产生了巨大的危害,同时严重影响了居民的生活质量,因此必须及时采取相应的措施控制噪声污染。然而由于噪声无形的特性导致城市噪声污染的治理难度巨大,面对复杂的噪声污染问题只有通过污染部门、治理部门以及市民的积极合作才能将其危害降到最低。本文首先分析了城市噪声的源头,其次指出了噪声污染的危害,最后提出了针对城市噪声污染的控制策略。本文以城市噪声污染的危害及控制技术的应用为题,是具有一定的社会价值和显示意义的。 相似文献
7.
对比了我国《实用供热空调设计手册》所用噪声计算方法与美国ASHRAE,英国CIBSE guide以及日本《空气调节·卫生工学便览》中所列方法。通过算例计算重点比较了中美两国手册在直管段气动噪声,弯头气动噪声,三通气动噪声和末端风口处气动噪声及各部件处噪声衰减计算上的异同。最终,除直管和弯头处噪声衰减以及声学指向性系数的计算略有出入外,主要差异集中于三通处气动噪声的计算。 相似文献
8.
气动凿岩机是一种自由活塞式的冲击机器。通常,气动凿岩机在冲程时,活塞冲击钎柄使钎头破碎矿石,在回程时,活塞转动一个角度,传给钎柄和钎头,使钎头的刃部在下一次冲击时破碎另一部分矿石。这样冲击——迴转的动作每分钟进行2000次左右,于是在矿床或者岩石钻出一个圆形的炮眼。近代出现了个别的气动幽岩机,它们有的在冲程转动钎子,有的使用了独立的迴转机构,但仍然是冲击——迴转作用机器。这 相似文献
9.
前言从我们收集到国内外的气动凿岩机性能参数计算公式来看,都基本相似,甚至修正系数的取值范围也都非常接近。我们认为这套公式可作为设计气动凿岩机时,进行性能参数计算的重要公式来应用。但这套公式经一系列的数学推导、变换得比较简单,应用的关键是如何正确选择公式中修正系数的具体问题。为了能合理地选取修正系数值,以便能较精确地计算气动凿岩机的性能参数,本人以多年来收集的 相似文献
10.
液压凿岩机械是在气动凿岩机的基础上发展起来的,早在20世纪初英国就作过研制液压凿岩机的尝试,但真正投入市场是在70年代初法国蒙特贝特(Montabert)公司推出第一台液压凿岩机及其配套台车以后,相继瑞典Atlas Copco,芬兰Tamrock,日本Frukawa,美国Ingersoll-Rand等公司也推出了 相似文献
11.
12.
13.
介绍一种消声器综合性能指标的测量评价方法.利用噪声和压力测量装置对某型全液压挖掘机实际设计消声器的插入损失和压力损失进行测量,检验该消声器的综合性能指标.在额定转速2 200 r/min时,通过对设计消声器的消声性能和空气动力性能进行测量,发现此转速下消声器的插入损失为21.8dB(A).经过对设计消声器内部进行去毛刺,对焊痕及穿孔管穿孔等部位进行光滑处理后,压力损失达到了国家规定的合格限值,消声器的综合性能符合设计要求.该测量方法简单,经济适用,对消声器的研究有一定的指导意义. 相似文献
14.
15.
介绍了噪声的概念及其危害 ,分析了空调系统产生的噪声源 ,从空调系统机械设备的选型和设备布置等方面 ,提出了空调系统消声设计的具体措施 相似文献
16.
为测试分析并设法降低家用电器的噪声,国内外正在开展动态型消声室设计研究.结合两个测试空调器噪声的带工况精密级消声室的工程实例,分析了带工况消声室的设计要求、技术难点,介绍了所采取的主要措施及效果. 相似文献
17.
H. Schunnesson 《International Journal of Rock Mechanics and Mining Sciences》1998,35(6):711-725
Despite considerable advantages such as reliable hardware, no disturbance in production, fast analysis and presentation of results and very low operational cost, the use of percussive drill monitoring to retrieve geological and geomechanical information concerns the drilled rock has not become a standard investigation tool in the underground industry. One major obstacle is the analysis of data. The monitored “raw” data can be affected by a significant influence from the operator, who often adjusts the drill settings in order to achieve the best drilling result. Furthermore, the advanced control system on a modern drill rig adjusts drill parameters independently to avoid drilling problems and damage to the drill string and machine. In order to use percussive drill monitoring in industrial applications, the performed analysis must be able to handle variations among monitored drill parameters, but still separate rock dependent variation from other influences on the monitored drilling data. Once the external influences on the drilling data have been normalised only leaving the rock dependant variation, rock properties can be predicted using theoretical or heuristic relations, or calibrated with observed rock conditions using statistical analysis. The method of analysis suggested in this paper is based on a step-wise normalisation of raw drilling data, where hole length dependent variation initially is removed, followed by a normalisation of the thrust dependent variation, and finally, by removing the influence of penetration rate on torque pressure. The analysis shows that major classification errors can be made if raw data are used instead of normalised data. The technique is applied on modern drill monitoring data from three different drilling sites, in crystalline rock masses in Sweden. The drill data selected were obtained during normal drilling conditions, where no special steps had been taken to promote the analysis or the interpretation. Examples from each site show good potential to predict ore boundaries and fracturing based on normalised drill parameters from percussive drilling. 相似文献
18.
Hydraulic rock drill with no constant-pressurized chamber is widely used now. The performance of the hydraulic impact mechanism directly influences the overall performance of the rock drill. Dynamic simulation and test research of the impact mechanism were carried out. Dynamic simulation is realized by numerical calculation based on the mathematical model. Two types of hydraulic rock drill YYG138 and YYG150 are tested on the horizontal stand. The numerical results are basically consistent with test results. 相似文献
19.
结合具体工程实例,分析了跟管钻进管棚施工与常规钻机管棚施工的区别,详细介绍了跟管钻机管棚施工工艺,成功解决了常规钻机卡钻、塌孔的难题,提高了施工效率及施工质量,对于软弱围岩条件下管棚施工,具有积极的推广意义。 相似文献
20.
本从轨行门架式凿岩台车上的凿岩机及其以承形式,台车机体结构型式及使用台车时的轨道布置形式,阐述了轨行门架式凿岩台车的发展过程;国内外轨行门架式凿岩台车的使用概况;该台车配套使用机械,台车的部分关键部件等。 相似文献