Advanced spinning disk‐TIRF microscopy for faster imaging of the cell interior and the plasma membrane

Understanding the cellular processes that occur between the cytosol and the plasma membrane is an important task for biological research. Till now, however, it was not possible to combine fast and high‐resolution imaging of both the isolated plasma membrane and the surrounding intracellular volume. Here, we demonstrate the combination of fast high‐resolution spinning disk (SD) and total internal reflection fluorescence (TIRF) microscopy for specific imaging of the plasma membrane. A customised SD‐TIRF microscope was used with specific design of the light paths that allowed, for the first time, live SD‐TIRF experiments at high acquisition rates. A series of experiments is shown to demonstrate the feasibility and performance of our setup.     

A review of high-pressure freezing preparation techniques for correlative light and electron microscopy of the same cells and tissues

In this paper, we review some published studies using correlative light and electron microscopy methods. We further refined our criteria to include only those studies using live cells for light microscope and where high-pressure freezing was the method of specimen preparation for electron microscopy. High-pressure freezing is especially important for some difficult-to-fix samples, and for optimal preservation of ultrastructure in samples larger than a few micrometres. How the light microscope observations are done is completely sample dependent, but the choice of high-pressure freezer depends on the speed required to capture (freeze) the biological event of interest. For events requiring high time resolution (in the 4–5 s range) the Leica EM PACT2 with rapid transfer system works well. For correlative work on structures of interest that are either non-motile or moving slowly (minutes rather than seconds), any make of high-pressure freezer will work. We also report on some efforts to improve the capabilities of the Leica EM PACT2 rapid transfer system.     

Correlative microscopy: a potent tool for the study of rare or unique cellular and tissue events

Biological studies have relied on two complementary microscope technologies – light (fluorescence) microscopy and electron microscopy. Light microscopy is used to study phenomena at a global scale to look for unique or rare events, and it also provides an opportunity for live imaging, whereas the forte of electron microscopy is the high resolution. Traditionally light and electron microscopy observations are carried out in different populations of cells/tissues and a 'correlative' inference is drawn. The advent of true correlative light-electron microscopy has allowed high-resolution imaging by electron microscopy of the same structure observed by light microscopy, and in advanced cases by video microscopy. Thus a rare event captured by low-resolution imaging of a population or transient events captured by live imaging can now also be studied at high resolution by electron microscopy. Here, the potential and difficulties of this approach, along with the most impressive breakthroughs obtained by these methods, are discussed.     

Pros and cons: cryo-electron microscopic evaluation of block faces versus cryo-sections from frozen-hydrated skin specimens prepared by different techniques

Over the last two decades, several different preparative techniques have been developed to investigate frozen‐hydrated biological samples by electron microscopy. In this article, we describe an alternative approach that allows either ultrastructural investigations of frozen human skin at a resolution better than 15 nm or sample throughput that is sufficiently high enough for quantitative morphological analysis. The specimen preparation method we describe is fast, reproducible, does not require much user experience or elaborate equipment. We compare high‐pressure freezing with plunge freezing, and block faces with frozen‐hydrated slices (sections), to study variations in cell thickness upon hydration changes. Plunge freezing is optimal for morphological and stereological investigations of structures with low water content. By contrast, high‐pressure freezing proved optimal for high‐resolution studies and provided the best ultrastructural preservation. A combination of these fast‐freezing techniques with cryo‐ultramicrotomy yielded well‐preserved block faces of the original biological material. Here we show that these block faces did not exhibit any of the artefacts normally associated with cryo‐sections, and – after evaporating a heavy metal and carbon onto the surface – are stable enough in the electron beam to provide high‐resolution images of large surface areas for statistical analysis in a cryo‐SEM (scanning electron microscope). Because the individual preparation steps use only standard equipment and do not require much experience from the experimenter, they are generally more usable, making this approach an interesting alternative to other methods for the ultrastructural investigation of frozen‐hydrated material.     

Electron microscopy of the early Caenorhabditis elegans embryo

The early Caenorhabditis elegans embryo is currently a popular model system to study centrosome assembly, kinetochore organization, spindle formation, and cellular polarization. Here, we present and review methods for routine electron microscopy and 3D analysis of the early C. elegans embryo. The first method uses laser‐induced chemical fixation to preserve the fine structure of isolated embryos. This approach takes advantage of time‐resolved fixation to arrest development at specific stages. The second method uses high‐pressure freezing of whole worms followed by freeze‐substitution (HPF‐FS) for ultrastructural analysis. This technique allows staging of developing early embryos within the worm uterus, and has the advantage of superior sample preservation required for high‐resolution 3D reconstruction. The third method uses a correlative approach to stage isolated, single embryos by light microscopy followed by HPF‐FS and electron tomography. This procedure combines the advantages of time‐resolved fixation and superior ultrastructural preservation by high‐pressure freezing and allows a higher throughput electron microscopic analysis. The advantages and disadvantages of these methods for different applications are discussed.     

Micro‐CT scouting for transmission electron microscopy of human tissue specimens

Transmission electron microscopy (TEM) provides sub‐nanometre‐scale details in volumetric samples. Samples such as pathology tissue specimens are often stained with a metal element to enhance contrast, which makes them opaque to optical microscopes. As a result, it can be a lengthy procedure to find the region of interest inside a sample through sectioning. We describe micro‐CT scouting for TEM that allows noninvasive identification of regions of interest within a block sample to guide the sectioning step. In a tissue pathology study, a bench‐top micro‐CT scanner with 10 μm resolution was used to determine the location of patches of the mucous membrane in osmium‐stained human nasal scraping samples. Once the regions of interest were located, the sample block was sectioned to expose that location, followed by ultra‐thin sectioning and TEM to inspect the internal structure of the cilia of the membrane epithelial cells with nanometre resolution. This method substantially reduced the time and labour of the search process from typically 20 sections for light microscopy to three sections with no added sample preparation.     

The transillumination possibility of imidazole-osmium postfixed muscle tissue and its consequences for the handling of muscle tissue samples

The osmium postfixation of tissue leads to good results for transmission electron microscopy, but also produces completely blackened tissue samples that do not allow the recognition of internal structures. With imidazole-osmium postfixation, one achieves comparable results in high electron microscopic resolution as with routine osmium postfixation. But the tissue samples are not blackened and can, therefore, be transilluminated with point light sources. The new postfixation technique makes it possible to recognize histological details such as vessels, nerve fibers, and the cross-banding pattern in an untrimmed block. This makes it possible to screen-embedded tissue samples for appropriate ultrastructural processing.     

Combining FIB milling and conventional Argon ion milling techniques to prepare high‐quality site‐specific TEM samples for quantitative EELS analysis of oxygen in molten iron

This paper reports a procedure to combine the focused ion beam micro‐sampling method with conventional Ar‐milling to prepare high‐quality site‐specific transmission electron microscopy cross‐section samples. The advantage is to enable chemical and structural evaluations of oxygen dissolved in a molten iron sample to be made after quenching and recovery from high‐pressure experiments in a laser‐heated diamond anvil cell. The evaluations were performed by using electron energy‐loss spectroscopy and high‐resolution transmission electron microscopy. The high signal to noise ratios of electron energy‐loss spectroscopy core‐loss spectra from the transmission electron microscopy thin foil, re‐thinned down to 40 nm in thickness by conventional Argon ion milling, provided us with oxygen quantitative analyses of the quenched molten iron phase. In addition, we could obtain lattice‐fringe images using high‐resolution transmission electron microscopy. The electron energy‐loss spectroscopy analysis of oxygen in Fe_0.94O has been carried out with a relative accuracy of 2%, using an analytical procedure proposed for foils thinner than 80 nm. Oxygen K‐edge energy‐loss near‐edge structure also allows us to identify the specific phase that results from quenching and its electronic structure by the technique of fingerprinting of the spectrum with reference spectra in the Fe‐O system.     

Controlled microaspiration for high-pressure freezing: a new method for ultrastructural preservation of fragile and sparse tissues for TEM and electron tomography

High‐pressure freezing is the preferred method to prepare thick biological specimens for ultrastructural studies. However, the advantages obtained by this method often prove unattainable for samples that are difficult to handle during the freezing and substitution protocols. Delicate and sparse samples are difficult to manipulate and maintain intact throughout the sequence of freezing, infiltration, embedding and final orientation for sectioning and subsequent transmission electron microscopy. An established approach to surmount these difficulties is the use of cellulose microdialysis tubing to transport the sample. With an inner diameter of 200 μm, the tubing protects small and fragile samples within the thickness constraints of high‐pressure freezing, and the tube ends can be sealed to avoid loss of sample. Importantly, the transparency of the tubing allows optical study of the specimen at different steps in the process. Here, we describe the use of a micromanipulator and microinjection apparatus to handle and position delicate specimens within the tubing. We report two biologically significant examples that benefit from this approach, 3D cultures of mammary epithelial cells and cochlear outer hair cells. We illustrate the potential for correlative light and electron microscopy as well as electron tomography.     

Out‐of‐focus background subtraction for fast structured illumination super‐resolution microscopy of optically thick samples

We propose a structured illumination microscopy method to combine super resolution and optical sectioning in three‐dimensional (3D) samples that allows the use of two‐dimensional (2D) data processing. Indeed, obtaining super‐resolution images of thick samples is a difficult task if low spatial frequencies are present in the in‐focus section of the sample, as these frequencies have to be distinguished from the out‐of‐focus background. A rigorous treatment would require a 3D reconstruction of the whole sample using a 3D point spread function and a 3D stack of structured illumination data. The number of raw images required, 15 per optical section in this case, limits the rate at which high‐resolution images can be obtained. We show that by a succession of two different treatments of structured illumination data we can estimate the contrast of the illumination pattern and remove the out‐of‐focus content from the raw images. After this cleaning step, we can obtain super‐resolution images of optical sections in thick samples using a two‐beam harmonic illumination pattern and a limited number of raw images. This two‐step processing makes it possible to obtain super resolved optical sections in thick samples as fast as if the sample was two‐dimensional.     

A novel approach for correlative light electron microscopy analysis

Correlative light and electron microscopy (CLEM) is a multimodal technique of increasing utilization in functional, biochemical, and molecular biology. CLEM attempts to combine multidimensional information from the complementary fluorescence light microscopy (FLM) and electron microscopy (EM) techniques to bridge the various resolution gaps. Within this approach the very same cell/structure/event observed at level can be analyzed as well by FLM and EM. Unfortunately, these studies turned out to be extremely time consuming and are not suitable for statistical relevant data. Here, we describe a new CLEM method based on a robust specimen preparation protocol, optimized for cryosections (Tokuyasu method) and on an innovative image processing toolbox for a novel type of multimodal analysis. Main advantages obtained using the proposed CLEM method are: (1) hundred times more cells/structures/events that can be correlated in each single microscopy session; (2) three‐dimensional correlation between FLM and EM, obtained by means of ribbons of serial cryosections and electron tomography microscopy (ETM); (3) high rate of success for each CLEM experiment, obtained implementing protection of samples from physical damage and from loss of fluorescence; (4) compatibility with the classical immunogold and immunofluorescence labeling techniques. This method has been successfully validated for the correlative analysis of Russel Bodies subcellular compartments. Microsc. Res. Tech., 2010. © 2009 Wiley‐Liss, Inc.     

High-resolution compact X-ray microscopy

We demonstrate compact full‐field soft X‐ray transmission microscopy with sub 60‐nm resolution operating at λ= 2.48 nm. The microscope is based on a 100‐Hz regenerative liquid‐nitrogen‐jet laser‐plasma source in combination with a condenser zone plate and a micro‐zone plate objective for high‐resolution imaging onto a 2048 × 2048 pixel CCD detector. The sample holder is mounted in a helium atmosphere and allows imaging of both dry and wet specimens. The microscope design enables fast sample switching and the sample can be pre‐aligned using a visible‐light microscope. High‐quality images can be acquired with exposure times of less than 5 min. We demonstrate the performance of the microscope using both dry and wet samples.     

Gridded Aclar: preparation methods and use for correlative light and electron microscopy of cell monolayers,by TEM and FIB–SEM

Aclar, a copolymer film with properties very similar to those of tissue culture plastic, is a versatile substrate to grow cells for light (including fluorescence) and electron microscopic applications in combination with both chemical fixation and cryoimmobilization. In this paper, we describe complete procedures to perform correlative light and electron microscopy using Aclar as substrate for the culture of cell monolayers to be finally embedded in plastic. First, we developed straightforward, efficient and flexible ways to mark the surface of the Aclar to create substrates to locate cells first at the light microscopy and then the electron microscopy level. All the methods enable the user to self‐design gridded Aclar pieces, according to the purpose of the experiments, and create a large number of substrates in a short time. Second, we confirmed that marked Aclar supports the normal growth and morphology of cells. Third, we validated the correlative light and electron microscopy procedure using Aclar. This validation was done for the high‐resolution analysis of endothelial cells using transmission electron microscopy and focused ion beam–scanning electron microscopy in combination with the use of fluorescence, phase contrast and/or bright field microscopy to map areas of interest at low resolution. The methods that we present are diverse, easy to implement and highly reproducible, and emphasize the versatility of Aclar as a cell growth substrate for diverse microscopic applications.     

Use of a night vision intensifier for direct visualization by eye of far-red and near-infrared fluorescence through an optical microscope

We describe the design, construction and testing of a prototype device that allows the direct visualization by eye of far‐red and near‐infrared (NIR) fluorescence through an optical microscope. The device incorporates a gallium arsenide (GaAs) image intensifier, typically utilized in low‐light or ‘night vision’ applications. The intensifier converts far‐red and NIR light into electrons and then into green light, which is visible to the human eye. The prototype makes possible the direct, real‐time viewing by eye of normally invisible far‐red and NIR fluorescence from a wide variety of fluorophores, using the full field of view of the microscope to which it is applied. The high sensitivity of the image intensifier facilitates the viewing of a wide variety of photosensitive specimens, including live cells and embryos, at vastly reduced illumination levels in both fluorescence and bright‐field microscopy. Modifications to the microscope are not required in order to use the prototype, which is fully compatible with all current fluorescence techniques. Refined versions of the prototype device will have broad research and clinical applications.     

Correlation of two‐photon in vivo imaging and FIB/SEM microscopy

Advances in the understanding of brain functions are closely linked to the technical developments in microscopy. In this study, we describe a correlative microscopy technique that offers a possibility of combining two‐photon in vivo imaging with focus ion beam/scanning electron microscope (FIB/SEM) techniques. Long‐term two‐photon in vivo imaging allows the visualization of functional interactions within the brain of a living organism over the time, and therefore, is emerging as a new tool for studying the dynamics of neurodegenerative diseases, such as Alzheimer's disease. However, light microscopy has important limitations in revealing alterations occurring at the synaptic level and when this is required, electron microscopy is mandatory. FIB/SEM microscopy is a novel tool for three‐dimensional high‐resolution reconstructions, since it acquires automated serial images at ultrastructural level. Using FIB/SEM imaging, we observed, at 10 nm isotropic resolution, the same dendrites that were imaged in vivo over 9 days. Thus, we analyzed their ultrastructure and monitored the dynamics of the neuropil around them. We found that stable spines (present during the 9 days of imaging) formed typical asymmetric contacts with axons, whereas transient spines (present only during one day of imaging) did not form a synaptic contact. Our data suggest that the morphological classification that was assigned to a dendritic spine according to the in vivo images did not fit with its ultrastructural morphology. The correlative technique described herein is likely to open opportunities for unravelling the earlier unrecognized complexity of the nervous system.     

Preservation of protein fluorescence in embedded human dendritic cells for targeted 3D light and electron microscopy

In this study, we present a correlative microscopy workflow to combine detailed 3D fluorescence light microscopy data with ultrastructural information gained by 3D focused ion beam assisted scanning electron microscopy. The workflow is based on an optimized high pressure freezing/freeze substitution protocol that preserves good ultrastructural detail along with retaining the fluorescence signal in the resin embedded specimens. Consequently, cellular structures of interest can readily be identified and imaged by state of the art 3D confocal fluorescence microscopy and are precisely referenced with respect to an imprinted coordinate system on the surface of the resin block. This allows precise guidance of the focused ion beam assisted scanning electron microscopy and limits the volume to be imaged to the structure of interest. This, in turn, minimizes the total acquisition time necessary to conduct the time consuming ultrastructural scanning electron microscope imaging while eliminating the risk to miss parts of the target structure. We illustrate the value of this workflow for targeting virus compartments, which are formed in HIV‐pulsed mature human dendritic cells.     

A simple,straightforward correlative live‐cell‐imaging‐structured‐illumination‐microscopy approach for studying organelle dynamics

Most cellular organelles are highly dynamic and continuously undergo membrane fission and fusion to mediate their function. Documenting organelle dynamics under physiological conditions, therefore, requires high temporal resolution of the recording system. Concurrently, these structures are relatively small and determining their substructural organization is often impossible using conventional microscopy. Structured Illumination Microscopy (SIM) is a super resolution technique providing a two‐fold increase in resolution. Importantly, SIM is versatile because it allows the use of any fluorescent dye or protein and, hence, is highly applicable for cell biology. However, similar to other SR techniques, the applicability of SIM to high‐speed live cell imaging is limited. Here we present an easy, straightforward methodology for coupling of high‐speed live cell recordings, using spinning disk (SD) microscopy, with SIM. Using this simple methodology, we are able to track individual mitochondrial membrane fission and fusion events in real time and to determine the network connectivity and substructural organization of the membrane at high resolution. Applying this methodology to other cellular organelles such as, ER, golgi, and cilia will no doubt contribute to our understanding of membrane dynamics in cells. Microsc. Res. Tech. 78:777–783, 2015. © 2015 Wiley Periodicals, Inc.     

Ultrafast photon counting applied to resonant scanning STED microscopy

To take full advantage of fast resonant scanning in super‐resolution stimulated emission depletion (STED) microscopy, we have developed an ultrafast photon counting system based on a multigiga sample per second analogue‐to‐digital conversion chip that delivers an unprecedented 450 MHz pixel clock (2.2 ns pixel dwell time in each scan). The system achieves a large field of view (～50 × 50 μm) with fast scanning that reduces photobleaching, and advances the time‐gated continuous wave STED technology to the usage of resonant scanning with hardware‐based time‐gating. The assembled system provides superb signal‐to‐noise ratio and highly linear quantification of light that result in superior image quality. Also, the system design allows great flexibility in processing photon signals to further improve the dynamic range. In conclusion, we have constructed a frontier photon counting image acquisition system with ultrafast readout rate, excellent counting linearity, and with the capacity of realizing resonant‐scanning continuous wave STED microscopy with online time‐gated detection.     

Light sources and cameras for standard in vitro membrane potential and high‐speed ion imaging

Membrane potential and fast ion imaging are now standard optical techniques routinely used to record dynamic physiological signals in several preparations in vitro. Although detailed resolution of optical signals can be improved by confocal or two‐photon microscopy, high spatial and temporal resolution can be obtained using conventional microscopy and affordable light sources and cameras. Thus, standard wide‐field imaging methods are still the most common in research laboratories and can often produce measurements with a signal‐to‐noise ratio that is superior to other optical approaches. This paper seeks to review the most important instrumentation used in these experiments, with particular reference to recent technological advances. We analyse in detail the optical constraints dictating the type of signals that are obtained with voltage and ion imaging and we discuss how to use this information to choose the optimal apparatus. Then, we discuss the available light sources with specific attention to light emitting diodes and solid state lasers. We then address the current state‐of‐the‐art of available charge coupled device, electron multiplying charge coupled device and complementary metal oxide semiconductor cameras and we analyse the characteristics that need to be taken into account for the choice of optimal detector. Finally, we conclude by discussing prospective future developments that are likely to further improve the quality of the signals expanding the capability of the techniques and opening the gate to novel applications.