Gel-casted porous Al<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics by use of natural fibres as pore developers

An approach using ceramic shaping by gel-casting and addition of natural tropical fibres as burnable pore developers has been explored for development of porous alumina materials with predetermined pore structures. The fibres used have been characterized in terms of size, shape, water uptake and surface charge. The degree of fibres loading in slurry has been varied. It has been shown that the amount of added fibres correlates well with the measured porosity, the shape of the developed pores however deviating slightly with that of the introduced fibres. The ceramic bodies have been characterised in terms of porosity, shrinkage and flexural strength. It could be assumed that at fibres amount in slurry above 30% V, an open porosity appears which is accompanied by a sharp drop in strength. In order to explore the benefits of the gel-casting method for complex bodies development, two key issues need to be addressed: air evacuation prior to casting and lowering slurry viscosity at fibre loadings higher than the tested ones. For reaching the latter objective, surface modification of fibres has been undertaken.     

叔丁醇基凝胶注模成型制备氧化铝多孔陶瓷

以微米级Al2O3粉料为原料,叔丁醇为溶剂,采用凝胶注模成型工艺制备了氧化铝多孔陶瓷,并研究了Al2O3浆料的固相体积分数(分别为8%、10%、13%和15%)对1 500℃保温2 h烧后氧化铝多孔陶瓷的气孔率、气孔孔径分布、耐压强度、热导率和显微结构的影响.结果表明:当Al2O3浆料的固相体积分数从8%增加到15%时,氧化铝多孔陶瓷烧结体的总气孔率从71.2%逐渐降低至61.2%,气孔平均孔径从1.0 μm逐渐减小至0.78 μm,耐压强度从16.0 MPa逐渐增大至45.6 MPa,而热导率从1.03 W·(m·K)-1逐渐增大至1.83W·(m·K)-1.     

Properties of porous zirconia ceramics fabricated by using various pore-forming agents

The present work proposes a new method for fabrication partially stabilized porous zirconia ceramics using monoclinic zirconia as raw material, yttrium nitrate and magnesium compounds as pore-forming agents and stabilizers. Effects of different pore-forming agents, firing temperatures and firing time on properties of samples were investigated. Thermal decomposition of yttrium nitrate and magnesium compounds creates a large number of pores, and thus porous zirconia ceramics were fabricated. ZrO₂ can be partially stabilized by Y₂O₃ and MgO derived from the precursors. The porous ZrO₂ ceramics obtained by using Y(NO₃)₃·6H₂O and 4MgCO₃·Mg(OH)₂·6H₂O as pore-forming agents had relatively high stabilization ratio, uniform pores and high strength. The optimum firing temperature and firing time are 1400 °C and 3 h, and the samples have the stabilization ratio of 45.7%, high cold crushing strength (26 MPa), uniform pores, and apparent porosity is about 40%.     

Structure and properties of Al2O3-bonded porous fibrous YSZ ceramics fabricated by aqueous gel-casting

To meet requirements for high porosity and high strength, novel aqueous gel-casting process has been successfully developed to fabricate Al₂O₃-bonded porous fibrous YSZ ceramics with ρ-Al₂O₃ and YSZ fibers as raw materials. Microstructure, phase composition, apparent porosity, bulk density, thermal conductivity, and compressive strength of fabricated porous ceramics were investigated, and effects of fiber content on properties were discussed. According to results, bird nest 3D mesh with interlaced YSZ fibers and Al₂O₃ binder was formed, ensuring the ability to obtain high performance, lightweight ceramics. An increase in the number of YSZ fibers led to more complex interlaced arrangement of fibers and denser network structure of porous ceramics at retaining their stability. Furthermore, their apparent porosity and bulk density increased, whereas thermal conductivity and compressive strength decreased with increasing the fiber content. In particular, comparatively high porosity (71.1–72.7%), low thermal conductivity (0.209–0.503 W/mK), and relatively high compressive strength (3.45–4.24 MPa) were obtained for as-prepared porous ceramics, making them promising for applications in filters, thermal insulation materials, and separation membranes.     

Preparation of calcium hexaluminate porous ceramics by gel-casting method with polymethyl methacrylate as pore-forming agent

Calcium hexaluminate (CA₆) porous ceramics were prepared by gel-casting method, with α-Al₂O₃ and CaCO₃ as raw materials and polymethyl methacrylate (PMMA) microspheres as pore-forming agent. The effects of the amount of pore-forming agent PMMA microspheres on the phase composition, bulk density, apparent porosity, flexural strength, microstructure, thermal shock stability and thermal conductivity of CA₆ porous ceramics were systematically studied. The pores of CA₆ porous ceramics are mainly formed by the burning loss of PMMA microspheres and the decomposition of organic matter. Adding an appropriate amount of PMMA microspheres as pore-forming agent has a positive effect on the thermal shock stability of CA₆ porous ceramics. When the amount of pore-forming agent is 15 wt%, the volume density of CA₆ porous ceramics is 1.33 g/cm³, the porosity is 63%, the flexural strength is 13.9 MPa, the thermal shock times can reach 9 times, and the thermal conductivity is 0.293 W/(m·K), which can meet the application in refractory, ceramics or high temperature cement industries.     

Low pressure dependent elasticity of porous ceramics

The primary goal of this study was to characterize the influence of the pore-saturated gas media and their physical properties on the elasticity of porous ceramic materials. Resonant ultrasound spectroscopic measurements were performed on test specimens of alumina with ~40% porosity, zirconia with ~48% porosity, and sintered fully dense zirconia to determine the hydrostatic pressure-dependent macroscopic elasticity. Here, we report the variation of elasticity of porous and full dense samples over approximately five orders of magnitude (800-0.02 psi) in absolute pressure. The time evolution of mechanical equilibrium of the porous materials at low pressure and high-temperature conditions will also be discussed.     

Fabrication and properties of SiC porous ceramics using a polyurethane preparation process

SiC porous ceramics can be prepared by introducing the polyurethane preparation method into the production process of ceramic biscuits, followed by sintering at 1300?°C for 2?h under N₂ flux after the cross-linking of polycarbosilane at 220?°C for 4?h in air. The microstructures, mechanical properties and infiltrations of the SiC porous ceramics are investigated in detail. The best dispersal effect comes from the SiC slurry with xylene as the solvent and a mixture of Silok®7096 (1?wt%) and Anjeka®6041 (4?wt%) as the dispersant. The compressive strength of SiC porous ceramics with high porosity (69.53%) reaches 16.9?MPa. The heat treatment can increase infiltration, the rate of which (4.296?×?10^?7 mm²) after the heat treatment at 750?°C in air is approximately two times faster than that before the heat treatment. The SiC porous ceramics fabricated in this study will have potential application in active thermal protection systems.     

Novel design of elongated mullite reinforced highly porous alumina ceramics using carbonized rice husk as pore-forming agent

A facile strategy for the fabrication of elongated mullite reinforced porous alumina ceramics (PACs) using carbonized rice husk (CRH) as pore-forming agent and silica source is reported for the first time. A large amount of elongated mullite is synthesized in pores due to the reaction of amorphous silica in CRH skeleton and alumina ceramic powder. Elongated mullite acts as the bridges between pore walls, enhancing the compressive strength of PACs. Furthermore, secondary pores from the intersection of elongated mullite is favor of decreasing of the thermal conductivity. High performance PAC with porosity of 74.3% has been fabricated by employing 25 wt% CRH, which possesses relatively low thermal conductivity of 0.189 W/(m•K) and ultra-high compressive strength of 45 MPa. Its comprehensive performance is much better than that of existing ceramic materials. Our findings present a facile, eco-friendly and effective approach to fabricate high performance PACs as the high-temperature thermal insulation materials.     

Fabrication of porous fibrous alumina ceramics by direct coagulation casting combined with 3D printing

A novel forming method for preparing porous alumina ceramics using alumina fibers as raw materials by direct coagulation casting (DCC) combined with 3D printing was proposed. Porous fibrous alumina ceramics were fabricated through temperature induced coagulation of aqueous-based DCC process using sodium tripolyphosphate (STPP) as dispersant and adding K₂SO₄ as removable sintering additives. The sacrificial coated sand molds was fabricated by 3D printing technology, followed by the infiltration of silica sol solution for the subsequent suspension casting. Stable alumina suspension of 40 vol% solid loading was obtained by adding 2.0 wt% STPP and 40 wt% K₂SO₄. The controlled coagulation of the suspension could be realized after heating at 90 °C for about 35 min. The ceramic sample sintered at 1450 °C for 2 h showed the highest compressive strength of 24.33 MPa with porosity of 57.38%. All samples sintered at 1300–1450 °C had uniform pore size distributions with average pore size of 7.2 µm, which indicated the good structure stability when sintered at high temperature.     

Fabrication and characterization of porous cordierite ceramics prepared from fly ash and natural minerals

Low cost, single-phase porous cordierite ceramics are successfully synthesized by in-situ solid-state reactions from fly ash, quartz, and magnesite. The effects of sintering temperature and magnesite content on phase transformation, open porosity, bulk density, mechanical properties, and microstructure are carefully investigated. Factsage analyses are carried out to calculate the isopleth diagrams, and the results agree well with the experimental outcomes. Thermal gravimetric and differential scanning calorimeter analyses (TG-DSC) are performed to characterize the weight loss and transient behaviors of the raw materials. Linear thermal expansion properties are also studied. The α-cordierite phase is the only phase observed in S-3 (magnesite content 25%) sintered at 1300 °C for 2 h, and its linear thermal expansion coefficient (2.71 × 10⁻⁶ K⁻¹) is close to that of typical cordierite. Both the compressive strength (72.64 MPa) and flexural strength (23.92 MPa) of the as-synthesized samples are high with an open porosity of 33.16% and a bulk density of 1.61 g/cm³.     

Preparation and performance of lightweight porous ceramics using metallurgical steel slag

In this paper, porous ceramics with high porosity and low bulk density were prepared by using steel slag and kaolin as main raw materials and polyurethane sponge as template. The effects of steel slag particle size, zirconia addition, the solid content of the slurry, and the addition of polycarboxylic acid water-reducing agent on the properties of ceramics were studied. In addition, by adding a surfactant (Sodium dodecyl sulfate) to form fine pores on the original framework of the three-dimensional network porous ceramic, the shortcomings of the single as well as the uncontrollable density and porosity of the porous ceramic, which are produced by the template method, are improved. When the grinding time of steel slag is 90 min, the content of zirconia is 3% wt, the solid content of ceramic slurry is 64% wt, and 0.6% wt polycarboxylic acid water-reducing agent and 0.4% of surfactant are added, the prepared porous ceramic skeleton is clear and good. The porous ceramic has a low bulk density (as low as 157.869 kg/m³), high porosity (about 94.05%) and high compressive strength (0.2 MPa). The crystalline phase of it is mainly composed of anorthite, gehlenite, forsterite and quartz. The addition of zirconia, water-reducing agent and surfactant only changes the macrostructure of porous ceramics, and does not change its crystal phase composition. The preparation of porous ceramics from steel slag not only solves the recycling problem of steel slag, but also provides a good substitute for main raw materials of porous ceramics.     

Electrochemical synthesis of nickel hexacyanoferrate nanoarrays with dots, rods and nanotubes morphology using a porous alumina template

Transition metal hexacyanoferrate (MeHCF) have attracted extensive attention because of their outstanding properties including, electrocatalysis, molecular magnetism, biosensing and ion-exchange. This paper describes an approach for fabrication of ordered nanoarrays of Ni hexacyanoferrate (NiHCF) structures with different morphologies such as dots, rods and tubes in order to advance their properties and applications. The method is based on the conversion of Ni into NiHCF nanostructures by electrochemical oxidation in the presence of hexacyanoferrate ions, using nanoporous anodic alumina oxide (AAO) as a template. The structure and morphology of formed Ni and NiHCF nanoarrays were confirmed by scanning electron microscopy (SEM), showing agreement with the pore structures of the AAO template. The electrocatalytic activity of NiHCF nanorod array electrodes showed high catalytic properties for the detection of hydrogen peroxide and the potential to be used as a platform for direct biosensing applications. The ion-exchange ability of fabricated NiHCF nanostructures (nanorods and nanotubes) toward alkali cations such as Na⁺ has been successfully confirmed.     

淀粉燃料对多孔Al_2O_3-ZrO_2(Y_2O_3)陶瓷性能的影响

为了提高多孔Al2O3-ZrO2(Y2O3)陶瓷的强度,以尿素和淀粉为燃料,用低温燃烧法合成活性较高的Al2O3-ZrO2(Y2O3)复合粉体,并用此粉体制备了多孔Al2O3-Zr O2(Y2O3)陶瓷,研究燃烧前驱体中淀粉的外加量(质量分数分别为0、15%、25%、35%、45%、55%)对多孔陶瓷显气孔率、抗折强度和显微结构的影响。结果表明:与尿素为燃料相比,以尿素和淀粉为燃料能提高复合粉体的烧结活性,有效改善多孔陶瓷的显微结构,提高多孔陶瓷的抗折强度。     

Estimating thermal conductivities and elastic moduli of porous ceramics using a new microstructural parameter

Porous ceramics are numerically constructed based on the convexity of the void phase: microstructures with convex pores are representative of isolated or randomly overlapping spherical pores, while particulate materials with non-convex pores are composed of randomly overlapping, partial overlapping or partially sintered solid spheres. Finite element simulations show that, given the porosity, thermal conductivities and elastic moduli for convex porosity are larger than the values for non-convex pores. These conditions are not well described by solely porosity. By contrast, this study proposes a new microstructural parameter, <lp2>/(<ls2>+<lp2>), to estimate thermal conductivities and elastic moduli for both convex and non-convex pores. <ls2> and <lp2> are respectively mean-square solid chord length and mean-square pore chord length of cross-sections, which can be conveniently extracted from SEM images combined with chord length distributions of solid and void.     

Dendritic porous alumina with high porosity by directional freeze casting using a binary solution for bacterial removal

High-porosity dendritic porous alumina was fabricated by using tertiary butanol (TBA) hydrate crystals combined with directional freeze casting. The porosity of this porous alumina approximated 80 %, and its high porosity resulted in high water flux. Dendritic pores improved the physical interception capability of porous ceramics due to the intrinsic moving paths and intercepts from the pore structure. Changes in the TBA content (from 70 vol.% to 85 vol.%) caused a change in pore size from 36.58 μm to 11.54 μm and pore structure (change order: snowflake, dendritic, rod-like, and needle-like), which are important factors affecting water flux and interception capability. The interception and removal of Escherichia coli by 7 mm-height porous ceramics with dendritic structure and an average pore size of 27.90 μm reached 100 % at pH 7.2. This study provides a simple and low-cost method for the effective removal of bacteria.     

Low-temperature preparation of porous SiC ceramics using phosphoric acid as a pore-forming agent and a binder

Porous SiC ceramics combine the properties of both SiC ceramics and porous materials. Herein, we design a facile method via pressureless sintering at relatively low temperatures for the synthesis of porous SiC ceramics. In the synthesis process, phosphoric acid was used as the sintering additive that reacted with SiO₂ on the surface of SiC to form phosphates. The formed phosphates acted as a binder to connect the SiC particles. At a fixed temperature, the phosphates were partially decomposed and released a large amount of gas. This changed the pore structure of the ceramics and greatly improved their porosity. Finally, we obtained the porous SiC ceramics with high porosity and high strength. We investigate the effects of H₃PO₄ content on the phase composition, microstructure, porosity, mechanical properties and thermal expansion coefficient of the prepared porous SiC ceramics. It was shown that at the sintering temperature of 1200 °C, the highest porosity of the samples can reach 70.42% when the H₃PO₄ content is 25 wt%, and their bending strength reaches 36.11 MPa at room temperature when the H₃PO₄ content is 15 wt%. In addition, the porous SiC ceramics show good high-temperature stability with a bending strength of 42.05 MPa at 1000 °C and the thermal expansion coefficient of 3.966 × 10⁻⁶/°C.     

Preparation and properties of porous ceramics from nickel slag by aerogel gelcasting

To further resource industrial solid waste, porous ceramics with high porosity were prepared by a gelcasting method using nickel slag and kaolin as raw materials and hydrophilic nontoxic SiO₂ aerogel as a gelling agent. The effects of nickel slag content, dispersant and solid content on the properties and microstructure of porous ceramics were investigated in detail in terms of density, compressive strength, porosity, phase composition and micromorphology. The results confirmed that a certain amount of nickel slag can effectively improve the porosity of porous ceramics, while the addition of dispersant can promote the flow of the slurry, enhanced the denseness of the raw billet and significantly improved the compressive strength. However, its excessive use had a negative effect on the ceramic density and porosity. At the same time, the solid content played a key role in the performance of porous ceramics prepared by gelcasting, and too much solid content was also not conducive to the generation of pores. When the nickel slag content was 55%, the amount of dispersant was 2%, and the solid content was 60 vol%, the porous ceramic had a better overall performance, the density of the porous ceramic was 510 kg/m³, the compressive strength was 1.3 MPa, and the porosity reached 80.1%. The major crystalline phases of porous ceramics prepared by nickel slag were cordierite and anorthite.     

Investigating the effect of SPRM on mechanical strength and thermal conductivity of highly porous alumina ceramics

For recycling waste refractory materials in metallurgical industry, porous alumina ceramics were prepared via pore forming agent method from α-Al₂O₃ powder and slide plate renewable material. Effects of slide plate renewable material (SPRM) on densification, mechanical strength, thermal conductivity, phase composition and microstructure of the porous alumina ceramics were investigated. The results showed that SPRM effectively affected physical and thermal properties of the porous ceramics. With the increase of SPRM, apparent porosity of the ceramic materials firstly increased and then decreased, which brought an opposite change for the bulk density and thermal conductivity values, whereas the bending strength didn’t decrease obviously. The optimum sample A2 with 50 wt% SPRM introducing sintered at 1500 °C obtained the best properties. The water absorption, apparent porosity, bulk density, bending strength and thermal conductivity of the sample were 31.7%, 62.8%, 1.71 g/cm³, 47.1 ± 3.7 MPa and 1.73 W/m K, respectively. XRD analysis indicated that a small quantity of silicon carbide and graphite in SPRM have been oxidized to SiO₂ during the firing process, resulting in rising the porous microstructures. SEM micrographs illustrated that rod-like mullite grains combined with plate-like corundum grains to endow the samples with high bending strength. This study was intended to confirm the preparation of porous alumina ceramics with high porosity, good mechanical properties and low thermal conductivity by using SPRM as pore forming additive.     

Synthesis and characterization of mullite-ZrO2 porous fibrous ceramic for highly efficient oil-water separation

This work aimed to proposing a new strategy for preparing the mullite-ZrO₂ porous fibrous ceramic used as alternative matrix material for oil-water separation by the aqueous gel-casting method. The properties of the fabricated porous fibrous ceramics in terms of microstructure, phase composition, apparent porosity, bulk density and compressive strength were investigated and the separation behavior was predicted by analyzing the structural changes. It is demonstrated that the phase composition of green bodies consisted of bayerite, boehmite, ZrSiO₄ and YSZ, and the sintered sample contained mullite, ZrO₂ and YSZ. As the YSZ fibers increased, the porosity of the fabricated porous ceramic increased with the maximum value of 70.65% due to the formation of more pores caused by YSZ fibers. Moreover, a significant increase in compressive strength (up to 9.52–21.86 MPa) was observed with the increase of YSZ fibers. Therefore, the fabricated porous ceramics could be appropriative for advanced applications of separation membranes for oil-water separation.