Effect of Intense Self-Irradiation on the Phase Composition of Metallic Plutonium

The crystal structure of film samples of "high-level" (based on ²³⁸Pu) and low-level (based on ²³⁹Pu) metallic plutonium during their prolonged (up to 343 days) storage (self-irradiation) at room temperature was studied by X-ray diffraction. In the samples of high-level plutonium, the -Pu and -Pu lattices coexist. In the period of 40-60 days, the other known crystal modifications of plutonium (-Pu, -Pu, -Pu, and -Pu) are also present. Low-level plutonium had only the -Pu lattice. A possible origin of this phenomenon is discussed.     

Microstructural study of two LAS-type glass-ceramics and their parent glass

The two glass-ceramics studied here derive from the complex system (MgO,ZnO,Li₂O)-Al₂O₃-SiO₂ and are obtained by controlled devitrification of the same parent glass. Although they have the same chemical composition, one is a -quartz (or -eucryptite) type while the other one is a -spodumene glass-ceramic. A detailed microstructural analysis of these materials has been performed at different scales by several complementary characterization methods (SEM, TEM, DTA, XRD and FTIR). This extensive study has shown the great microstructure difference (grain distribution, grain size, nature of vitreous and crystalline phases) between these two glass-ceramics obtained from the same parent glass.     

One Method of Determination of the Effective Absorption Coefficient in Pulsed Laser Irradiation of Metals

An experimentaltheoretical method of determination of the absorption coefficients in laser treatment of metals has been proposed based on the solution of the boundaryvalue axisymmetric problem of heat conduction for a halfspace and metallographic measurements of the dimensions of the thermalhardening zone.     

Temperature effects on the properties of Ge thin films

The effects of substrate temperature (T_s) on the properties of vacuum evaporated p-type Ge thin films have been investigated for 25s<400°C. Increase in the substrate temperature improves the crystallinity and increases the grain size resulting a gradual change from amorphous to polycrystalline structure which was attained above a substrate temperature of 225°C. Low resistive (1×10^–2 ohm-cm) and high mobility (280 cm²/V·s) films were obtained at T_s=400°C. It has been observed that the conduction mechanism in polycrystalline films was dominated successively by hopping, tunneling and thermionic emission as the sample temperature was increased from 40 to 400 K. In amorphous samples, conduction was described in terms of different hopping mechanisms.     

Differential-flow-induced instability in a cubic autocatalator system

The formation of spatio-temporal stable patterns is considered for a reaction-diffusion-convection system based upon the cubic autocatalator, A + 2B 3B, B C, with the reactant A being replenished by the slow decay of some precursor P via the simple step P A. The reaction is considered in a differential-flow reactor in the form of a ring. It is assumed that the reactant A is immobilised within the reactor and the autocatalyst B is allowed to flow through the reactor with a constant velocity as well as being able to diffuse. The linear stability of the spatially uniform steady state (a, b) = (µ^–1, µ), where a and b are the dimensionless concentrations of the reactant A and autocatalyst B, and µ is a parameter reflecting the initial concentration of the precursor P, is discussed first. It is shown that a necessary condition for the bifurcation of this steady state to stable, spatially non-uniform, flow-generated patterns is that the flow parameter > _c(µ, ) where _c(µ,) is a (strictly positive) critical value of and is the dimensionless diffusion coefficient of the species B and also reflects the size of the system. Values of _c at which these bifurcations occur are derived in terms of µ and . Further information about the nature of the bifurcating branches (close to their bifurcation points) is obtained from a weakly nonlinear analysis. This reveals that both supercritical and subcritical Hopf bifurcations are possible. The bifurcating branches are then followed numerically by means of a path-following method, with the parameter as a bifurcation parameter, for representatives values of µ and . It is found that multiple stable patterns can exist and that it is also possible that any of these can lose stability through secondary Hopf bifurcations. This typically gives rise to spatio-temporal quasiperiodic transients through which the system is ultimately attracted to one of the remaining available stable patterns.     

γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

p-Version hierarchical three dimensional curved shell element for heat conduction

This paper presents a finite element formulation for a three dimensional nine node p-version hierarchical curved shell element for heat conduction where the element temperature approximation can be of arbitrary order p , p , and p in the , and directions. This is accomplished by first, constructing one dimensional hierarchical approximation functions and the corresponding nodal variable operators for each of the three directions , and using Lagrange interpolating polynomials and then taking their products (sometimes also called tensor products). The element approximation functions as well as the nodal variables are hierarchical and therefore the element matrices and the equivalent heat vectors are hierarchical also i.e. the element properties corresponding to polynomial orders p , p , and p are a subset of those corresponding to (p +1), (p +1), and (p +1). The element formulation ensures C ⁰ continuity. The curved shell geometry is constructed in the usual way by taking the coordinates of the nodes lying on the middle surface of the element (=0) and the nodal thickness vectors. The element properties i.e. element matrices and the equivalent heat vectors are derived using weak formulation (or quadratic functional) of the three dimensional F ourier heat conduction equation and the hierarchical element temperature approximation. The element formulation is equally effective for very thin as well as extremely thick shells. Numerical examples are presented to demonstrate the accuracy, efficiency, modeling convenience, faster rate of convergence and over all superiority of the present formulation. The h-approximation results are presented for comparison purposes.     

Nonlinear asymptotic theory of hypersonic flow past a circular cone

Summary The hypersonic small-disturbance theory is reexamined in this study. A systematic and rigorous approach is proposed to obtain the nonlinear asymptotic equation from the Taylor-Maccoll equation for hypersonic flow past a circular cone. Using this approach, consideration is made of a general asymptotic expansion of the unified supersonic-hypersonic similarity parameter together with the stretched coordinate. Moreover, the successive approximate solutions of the nonlinear hypersonic smalldisturbance equation are solved by iteration. Both of these approximations provide a closed-form solution, which is suitable for the analysis of various related flow problems. Besides the velocity components, the shock location and other thermodynamic properties are presented. Comparisons are also made of the zeroth-order with first-order approximations for shock location and pressure coefficient on the cone surface, respectively. The latter (including the nonlinear effects) demonstrates better correlation with exact solution than the zeroth-order approximation. This approach offers further insight into the fundamental features of hypersonic small-disturbance theory.Notation a speed of sound - H unified supersonic-hypersonic similarity parameter, - K hypersonic similarity parameter, M - M freestream Mach number - P pressure - T temperature - S entropy - u, v radial, polar velocities - V freestream velocity - shock angle - cone angle - density - density ratio, /() - ratio of specific heats - polar angle - stretched polar angle, / - (), (), () gage functions     

Thermal diffusivity of inhomogeneous systems

The possibility of analyzing the nonsteady temperature fields of inhomogeneous systems using the quasi-homogeneous-body model is investigated.Notation t, t_I, t_i temperature of quasi-homogeneous body inhomogeneous system, and i-th component of system - a, , c thermal diffusivity and conductivity and volume specific heat of quasi-homogeneous body - a_{i i}, c_i same quantities for the i-th component - q heat flux - S, V system surface and volume - x, y coordinates - macrodimension of system - dimensionless temperature Fo=a/² - Bi=/ Fourier and Biot numbers - N number of plates - =h/ ratio of micro- and macrodimensions - _V, volumeaveraged and mean-square error of dimensionless-temperature determination - time - m_i i-th component concentration Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 126–133, July, 1980.     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Deformation in spinel

Stoichiometric MgAl₂O₄ spinel was deformed in compression at temperatures from 1790 to 1895 C and the dislocation structures analysed by transmission electron microscopy. {1 1 1}1 1 0 slip was observed on both the primary and cross-slip systems, and there was much secondary slip as well; all six 1 1 0 Burgers vectors were present in electron micrographs. This secondary slip leads to very high work-hardening rates, approximately/70 at 1790 C, where is the shear modulus. Since it is known that deformation in nonstoichiometric (alumina-rich) spinel crystals occurs by {1 1 0}1 1 0 slip, the electrostatic and geometric aspects of 1/4 110 dislocations moving on {1 1 1} and {1 1 0} planes are considered in some detail. It is porposed that the octahedral cation vacancies present in non-stoichiometric spinel diffuse to dislocations during deformation and thus favour {1 1 0} slip.     

Elevated temperature deformation behaviour of multi-phase Ni-20 at % Al-30 at % Fe and its constituent phases

The mechanical behaviour of the multi-phase ( + /) alloy Ni-20 at % Al-30 at % Fe and alloys similar to its constituent and / phases, Ni-30 at % Al-20 at % Fe and Ni-12 at % Al-40 at % Fe, respectively, were investigated. When tested in tension at 300 K, the alloys exhibited 20%, 2% and 28% elongation, respectively. At elevated test temperatures (700, 900 and 1100 K), the multi-phase alloy exhibited increased ductility, reaching an elongation in excess of 70% at 1100 K without necking or fracture. Similarly, the alloy demonstrated increased ductility with increasing test temperatures. In contrast, the / alloy showed greatly reduced ductility with increasing temperature and was quite brittle both at 900 and 1100 K. Thus, whilst at room temperature the / phase improved the ductility of the + / aggregate, at elevated temperatures the phase alleviated the brittleness of the / phase, thereby preventing any embrittlement of the multi-phase alloy over the temperature range 300–1100 K. Also, whilst the phase improved the room-temperature strength of the multi-phase alloy, at elevated temperatures where the phase is known to be weak, the / phase improved the strength of the multi-phase alloy up to 900 K, beyond which the strength deteriorated due to disordering and lack of anomalous strengthening in the / component.     

Observations on the mechanical properties of nickel oxide scales

The mechanical properties of NiO scales produced by the complete oxidation of high-purity (grade-1) Ni and commercial-purity (grade-A) Ni have been investigated at 700 to 1000 C. The modulus of elasticity of both grades of oxide decreased with increasing temperature, whereas the modulus of rupture for grade-A oxide exhibited a maximum at 850 C and that for grade-1 oxide decreased with increasing temperature. At 700 C, elastic deformation to fracture occurred with both oxides, whereas, at temperatures 850 C, plasticity was also observed. The plasticity of grade-1 oxide was 3 times greater than that of grade-A oxide.Creep behaviour of the oxides was studied at 900 and 1000 C. Primary and secondary creep was observed and, in both oxides, the creep rates increased with increasing temperature and load. The creep rate of grade-1 oxide was 10 to 20 times greater than that for grade-A oxide.     

The influence of ageing on the stability of β-γ/γ′ derived microstructures in Ni-Al-Cr-(Co) alloys

Multiphase Ni-Al-(Fe)-(Cr)-(Co)-based intermetallics with (B2)- (A1)/(L1₂), - or - microstructures can exhibit significant room-temperature tensile ductility. In the case of Ni-Al-Cr-based alloys, microstructural development is complicated by the precipitation of -Cr, which can supplant the -phase during ageing of three-phase -/ microstructures. An investigation of the stability, during ageing, of cast Ni-Al-Cr-(Co) alloys with microstructures derived from -/ is reported. In the as-cast condition, the materials investigated consisted of a dendritic matrix containing L1₀ type martensite and interdendritic /. Extensive intra- and interdendritic -Cr precipitation was also observed. The stability during ageing of the interdendritic / microstructure is also considered and transformation of the L1₀ martensite is examined.     

The Possibility of Reproducing the Units of Complex Permittivity at High Frequencies

The results of theoretical investigations of the reproduction of the units of the components of complex permittivity and by a method based on the use of the wave properties of a coaxial line are presented. The errors in reproducing and are analyzed.     

Study of Broadband Long-Focus Optics for Synchrotron Infrared Diagnosis of Low-Energy Electron Beams

A special optical device for measuring the geometry and current parameters in electron rings by synchrotron infrared radiation is designed, fabricated, and studied. The optical elements of the device are made of an optical ceramic and operate at 1–8 m. The study results are presented.     

Thermal shock resistance of miniaturized multilayer ceramic capacitors

The thermal shock resistance of miniaturized multilayer ceramic capacitors (MLCs), of sizes 0402, 0603, 0805 and 1206, was investigated by comparing the leakage currents before and after thermal shock. It was generally found that smaller capacitors have a higher thermal shock resistance than larger ones. The 0402 MLC possesses a thermal shock resistance in excess of 420 C. The linear interdependence of thermal shock resistance and reciprocal of half thickness, as predicted by conventional thermal shock analysis, was not observed. Instead, the thermal shock resistance of an MLC was found to be inversely proportional to the total area of its ceramic surface. This confirms that pre-existing flaws on the ceramic surface dominate the crack initiation process and are therefore primarily responsible for determining the thermal shock resistance of an MLC.     

Flame quenching through endothermic reaction

A laminar premixed flame model is considered in which there is a second-order branching reaction coupled with an endothermic decay of a chemical inhibitor. An analysis, based on high activation energies for the reactions, is performed and two distinct cases are found. These depend on dimensionless parameters representing the loss of heat relative to its production, , and the consumption of inhibitor relative to that of fuel, . With 1, extinction is achieved through a saddle-node bifurcation at a critical value of . For , no extinction is found though considerable reductions in wave speed over the adiabatic limit are seen. The asymptotic results are compared with numerical simulations of an initial-value problem for the model.     

Application of coherent-optical methods in physical studies of evaporation

The application of the methods of laser and holographic interferometry to the problems of measuring evaporation rates is examined. Mass transfer accompanying evaporation in the region of extradiffusion monitoring is studied.Notation j_v specific mass flux of the vapor, kg/(m²·sec) - _c coefficient of condensation - _v coefficient of evaporation - D coefficient of diffusion - m²/sec, wetting angle - R radius of the vessel, m - time, sec - h height of the segment, m - wavelength of the laser radiation, m - N order of the interference fringe or the number of fringes passing through a given point - density of the matter, kg/m³ - length of the cell with the liquid of interest, m - T temperature, K - n refractive index of the medium - m mass - kg, V volume of the spheroidal segment, m³ - _liq and _g molar mass, kg/mole - C₀ and C_p concentration of vapor in the gas, kg/m³ - a and b semiaxes of the spheroid, m - _e ellipsoidal coordinate of a point on the surface, m² - c/n derivative along the normal - r coordinate of a point on the surface of evaporation, m - n change in the refractive index of the medium Indices st standard liquid - liq liquid - g gas - 0 starting state - p equilibrium pressure Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 55, No. 4, pp. 605–611, October, 1988.     

Simulation of the Process of Water Freezing in a Round Pipe

The problem of freezing of pure water in a round pipe is treated with due regard for convection under asymmetric thermal boundary conditions in the absence of motion along the pipe. The problem is solved numerically using the control volume approach, SIMPLER algorithm, and the enthalpy method. Results are obtained for three Grashof (Gr) and six Biot (Bi) numbers: Gr = 1.55 × 10⁶, Bi = 0.305 (0 < ), Bi = 0.044 ( < 2); Gr = 1.24 × 10⁷, Bi = 0.610 (0 < ), Bi = 0.087 ( < 2); Gr = 9.89 × 10⁷, Bi = 1.220 (0 < ), Bi = 0.174 ( < 2). The correctness of calculation of the problem disregarding free-convection flows is analyzed.