木瓜蛋白酶在[Cnmim]BF4-NaH2PO4双水相体系中的分配行为

为了研究木瓜蛋白酶在[Cnmim]BF4-NaH2PO4双水相体系中的分配行为,在298.15 K条件下利用浊点法测定了[Cnmim]BF4-NaH2PO4双水相体系的双节线和液液相平衡数据,建立了木瓜蛋白酶在该体系中的三维分配模型。利用Merchuk方程、Othmer-Tobias方程和Bancroft方程分别关联了双节线数据、液液相平衡数据,拟合度分别在0.975、0.994以上,结果满意。木瓜蛋白酶分配系数的对数与该体系上相的离子液体浓度和下相的盐浓度相关度都较高,故通过Matlab建立了三者之间的分配模型,实验值和预测值之间的相对偏差均在5%以内,表明该模型能有效地预测木瓜蛋白酶在[Cnmim]BF4-NaH2PO4双水相体系中的分配行为。     

木瓜蛋白酶在离子液体双水相中的分配行为

采用离子液体双水相提取木瓜蛋白酶。首先考察不同浓度、pH、温度的离子液体对木瓜蛋白酶活性的影响, 其次考察不同离子液体双水相体系、离子液体侧烷基链长度及浓度、酶添加量、pH、温度对木瓜蛋白酶分配行为的影响。结果表明:[C₄mim]Cl和[C₄mim]Br体系萃取木瓜蛋白酶的效果比[C₄mim]BF₄体系好;高温(≥60℃)对离子液体双水相体系萃取木瓜蛋白酶不利。离子液体双水相萃取木瓜蛋白酶的最佳工艺条件:0.25 g·ml^-1的[C₄mim]Cl, 0.35 g·ml^-1的K₂HPO₄, pH 8.0, 酶添加量2.0 mg·ml^-1, 30℃。此条件下木瓜蛋白酶的酶活性回收率达到95.16%, 纯化因子达到1.5。为今后进一步研究该体系的放大实验或规模化生产奠定了基础。     

吡啶基离子液体+有机盐双水相体系相图的测定及盐析性能研究

测定了离子液体N-乙基吡啶四氟硼酸盐([EPy]BF₄)+有机盐[丁二酸钠(CH₂COONa)₂/柠檬酸铵C₆H₅O₇(NH₄)₃/柠檬酸钠C₆H₅O₇Na₃]+水双水相体系在303.15、308.15和313.15 K下的双节线及系线数据。基于相图中的杠杆定律通过质量法研究双水相体系的系线,并用Othmer-Tobias方程、Bancroft方程等经验方程以及NRTL活度系数模型对数据进行关联。采用有效排除体积和Setschenow-type的拟合参数深入研究三种有机盐的盐析能力。结果表明,双节线的三个经验式拟合效果良好,但较多参数的经验式会导致部分参数失去意义;双水相体系的系线满足经验方程,数据可靠性较好,且均方根偏差表明系线数据很好地符合NRTL模型;低温更有利于该双水相体系的形成;三种盐都能和[EPy]BF4离子液体形...     

[Epy]BF_4-(NH_4)_3C_6H_5O_7-H_2O双水相体系液液相平衡测定及其关联

实验测定了298.15K,离子液体N-乙基吡啶四氟硼酸盐([Epy]BF4)与(NH4)3C6H5O7形成的双水相体系的液液相平衡数据。采用三个经验方程对得到的双节线数据关联,实验得到的双水相体系的系线数据,利用Setschenow-type方程进行关联,关联结果较为满意。利用双节线模型,计算了该体系的有效排除体积(EEV)。结果表明,双水相体系上相富含[Epy]BF4,下相则富含(NH4)3C6H5O7,该体系既能用于萃取分离,也可以用于从水溶液中分离回收离子液体。     

2,6-二甲氧基苯酚在1-丁基-3-甲基咪唑四氟硼酸盐水溶液中溶解行为的红外光谱分析

利用衰减全反射红外光谱(ATR-IR)和二维相关红外技术研究2, 6-二甲氧基苯酚(2, 6-DMP)在1-丁基-3-甲基咪唑四氟硼酸盐([C₄mim]BF₄)水溶液(离子液体摩尔分数x_IL=1.0～0.02)中的溶解行为。随着水量增大, 2, 6-DMP溶解度先增大而后急剧减小, 对应的x_IL阈值为0.1。2, 6-DMP与[C₄mim]BF₄之间存在强相互作用, 2, 6-DMP上的甲氧基是重要作用位点之一;当少量的水加入[C₄mim]BF₄(x_IL=0.1～1.0), 致密的离子簇结构被解离, 2, 6-DMP容易与[C₄mim]BF₄作用, 溶解度增大;随着大量水加入(0.02IL<0.1), 离子簇完全解离为大分子水簇包围的离子对, 憎水的2, 6-DMP与[C₄mim]BF₄作用困难, 溶解度减小。这种由于水量改变引起的[C₄mim]BF₄水溶液微观结构变化影响2, 6-DMP溶解行为。     

Electrical conductivities for four ternary electrolyte aqueous solutions with one or two ionic liquid components at ambient temperatures and pressure

Thiswork provides amethod to explore the transport property of the electrolyte aqueous solutionswith one or two ionic liquids, especially focus on their electrical conductivity. The conductivities were measured for the ternary systems NaCl–[C₆mim][Cl] (1-hexyl-3-methylimidazolium chloride)–H₂O, [C₆mim][BF₄]–[C₆mim][Cl]–H₂O, NaNO₃–[C₆mim][BF₄](1-hexyl-3-methylimidazolium tetrafluoroborate)–H₂O, and [C₄mim][BF₄] (1-butyl-3- methylimidazolium tetrafluoroborate)–[C₆mim][BF₄]–H₂O, and their binary subsystems NaNO₃–H₂O, NaCl–H₂O, [C₆mim][BF₄]–H₂O, [C₆mim][Cl]–H₂O, and [C₄mim][BF₄]–H₂O, respectively. The conductivities of the ternary systems were also determined using generalized Young's rule and semi-ideal solution theory in terms of the data of their binary solutions. The comparison showed that the two simple equations provide good predictions for conductivity of mixed electrolyte solutions and the mixed ionic liquid solutions based on the conductivity of their binary subsystems.     

离子液体N-乙基吡啶四氟硼酸盐与碳酸钠在298.15K下相行为的测定与关联

实验测定了离子液体([EPy]BF4)-碳酸钠(Na2CO3)-H2O双水相体系在298.15 K时液液相平衡数据。采用Merchuk方程关联双节线数据,相关系数达到0.995 9;采用Cashmere-Tobias和Bancroft方程关联系线数据,其相关系数分别为0.926 9和0.923 2。实验测定了系统、完整、准确的双水相体系相图数据,并用有效排除体积(EEV)评估了碳酸钠的盐析能力,为设计双水相萃取提供了数据基础。     

咪唑类离子液体对木质纤维预水解液的脱毒

针对燃料乙醇生物炼制过程中抑制物对酵母乙醇发酵的抑制作用,以水洗稀酸蒸汽爆破预处理玉米秸秆得到的预水解液为研究对象,采用新型绿色脱毒技术--离子液体进行萃取脱毒,研究比较了两种咪唑类离子液体[烷基咪唑六氟磷酸盐离子液体[C_nmim][PF₆](n 4,6,8)和烷基咪唑四氟硼酸盐离子液体[C_nmim][BF₄](n 6,8)]对预水解液的萃取性能。结果表明,随着咪唑类离子液体阳离子烷基链长度的增加,离子液体对抑制物的萃取性能下降,具有更强电负性的阴离子为BF₄^-的离子液体比阴离子为PF₆^-的离子液体萃取效率更高。通过比较糖与抑制物的萃取率,最终选择[C₈mim][BF₄]作为预水解液的萃取剂,结果显示其对主要抑制物甲酸、乙酸、5-羟甲基糠醛的萃取率分别为53.22%、47.53%和85.13%,总酚的萃取率为65.05%,而糖的损失率在6%以内。     

[Bmim][BF4]/MEA混合水溶液吸收CO2的吸收性能与液液分相机理

对液液两相CO₂吸收剂1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim][BF₄]）/乙醇胺（MEA）混合水溶液吸收性能进行了实验测定,研究了离子液体[Bmim][BF₄]的引入对吸收性能和液液分相的影响,并通过定量碳谱核磁共振法对分相机理和各相中的物质分布进行分析。研究结果表明,一定配比的[Bmim][BF₄]/MEA混合水溶液吸收CO₂之后会出现互不相溶的液液两相,这种现象伴随着CO₂产物的富集;导致液液分相的原因是氨基甲酸盐浓度的增大;随着[Bmim][BF₄]质量分数的增大,溶液吸收速率呈现出先增大后减小的趋势;分层后H₂O主要分布在富液相,[Bmim][BF₄]主要分布在贫液相,H₂O的质量分数直接影响分层后富液相的传质性能。     

离子液体对溶菌酶晶体形态和活性的影响

以鸡蛋清溶菌酶为模型蛋白,采用冷却结晶法结晶以及浊度法测定酶活性,研究了分别添加4种亲水性离子液体(1-丁基-3-甲基咪唑四氟硼酸盐([C₄mim]BF₄)、1-丁基-3-甲基咪唑氯盐([C₄mim]Cl)、1-丁基-3-甲基咪唑溴盐([C₄mim]Br)和1,3-二甲基咪唑碘化物([dmim]I))条件下溶菌酶晶体形态和晶体活性的变化。利用光学显微镜对溶菌酶结晶过程的晶体形态进行分析,结果表明添加离子液体会影响溶菌酶的晶体形态和尺寸。离子液体[C₄mim]BF₄介导的溶菌酶形成棒状晶体。与未添加离子液体相比,[C₄mim]Cl和[C₄mim]Br均未改变溶菌酶晶体形态,均呈块状晶体,但[C₄mim]Cl和[C₄mim]Br促进溶菌酶晶体生长,晶体尺度均增加。而添加[dmim]I,溶菌酶呈现针状晶体。采用浊度法测定溶菌酶晶体活性,结果表明不同的离子液体对溶菌酶晶体的活性...     

The effect of temperature on phase equilibria of polyethylene glycol (PEG8000)-K2SO4-H2O at T=(288.15, 298.15, 308.15) K

The phase behavior of potassium sulfate (K₂SO₄) in polyethylene glycol with molecular weight 8000 (PEG8000) and water (H₂O) mixed solvent at 288.15, 298.15, and 308.15 K were determined. According to the results, when the temperature are 288.15 and 298.15 K, there is only a solid-liquid phase equilibrium relationship in the system, and the phase diagrams are both divided into three parts which respectively are the regions of unsaturated homogeneous liquid (L), one liquid and one solid K₂SO₄ (L + S) and one liquid and two solids K₂SO₄ and PEG8000 (L + 2S). The solubility of K₂SO₄ in PEG8000-H₂O mixed solvent decreased with the addition of the PEG8000 in the solution. Comparing the diagrams of 288.15 and 298.15 K, the sizes of regions of (L) and (L + S) increased and that of (L + 2S) decreased with the increase of temperature. While at 308.15 K, solid-liquid and liquid-liquid equilibrium coexist, and there are six parts in the complete phase diagram at 308.15 K, adding the areas of one liquid and one solid K₂SO₄ (L + S), two liquids (2 L), two liquids and one solid K₂SO₄ (2 L + S). The equations developed by Merchuk, Hu, and Jayapal were used to fit the binodal curves data of the system at 308.15 K, meanwhile, the experimental tie-line data of the system at 308.15 K were correlated by Othmer-Tobias equation and Bancroft equation.     

交互四元体系K+,NH4+//Cl-,H2PO4——H2O 在313.15 K时相平衡研究

采用等温溶解平衡法研究了交互四元体系K⁺,NH₄⁺//Cl^-,H₂PO₄^--H₂O以及子体系KCl-NH₄Cl-H₂O在313.15 K时的固-液相平衡关系,并根据实验数据绘制了四元体系及子体系的相关相图和水图,采用湿渣法与X射线衍射相结合的方法对平衡固相进行鉴定。实验结果表明,三元体系KCl-NH₄Cl-H₂O是一个部分互溶体系,相图有一个共结晶点、2条单变量曲线、5个结晶区;交互四元体系K⁺,NH₄⁺//Cl^-,H₂PO₄^--H₂O中形成了（K,NH₄）Cl和（K,NH₄）H₂PO₄两种固溶体,该四元相图包括2个共饱和点、5条单变量曲线及4个结晶区。实验结果可为该体系的共结晶研究、相应的模型拟合计算提供必要基础数据。     

低黏二氰胺类离子液体乙烯汽液相平衡研究

从工业废气中回收分离乙烯（C₂H₄）具有重要意义,选用了三种低黏度二氰胺类离子液体,分别测定了293.15~333.15 K下其密度、黏度等物化性质,研究了其对乙烯（C₂H₄）吸收性能。采用非随机（局部）双液体模型（NRTL）关联了三种二元体系溶解度数据,实验值与计算值的平均相对偏差均小于3%。结果表明,低黏度二氰胺类离子液体对C₂H₄气体吸收性能良好,其中阳离子侧链长度增加和羟基功能团引入可增强对C₂H₄溶解度。同时,离子液体1-丁基-3-甲基咪唑二氰胺盐（[Bmim][DCN]）经过3次的吸收解吸循环,仍可以保持较好的C₂H₄吸收性能,表明该离子液体循环稳定性好,而1-丁基-3-甲基咪唑二氰胺盐（[Bmim][DCN]）对乙烯吸收量较高,具有作为C₂H₄吸收剂的潜力。     

Binary mixtures of HMIMPF6 ionic liquid and n-butyl acetate cosolvent in the extraction of acetone from aqueous solutions

A remarkable disadvantage of pure ionic liquids, to be used as a solvent in different processes, is their high viscosity and density. Here, n-butyl acetate was used as a cosolvent in the liquid–liquid system of {water?+?acetone?+?1-hexyl-3-methylimidazolium hexafluorophosphate (HMIMPF₆) ionic liquid}. Mixtures of the ionic liquid and the cosolvent were used as the organic phase to extract acetone from aqueous phase. A drastic decrease in viscosity and a significant decrease in density of the ionic liquid were achieved in the presence of cosolvent. Accordingly, the liquid–liquid equilibrium of different provided systems was studied under temperature of 298.2?K and atmospheric pressure of 81.5?kPa. Binary phase regions and corresponding tie-lines and binodal curves were obtained for ternary and quaternary systems. Results show the extension of the binodal solubility region as well as enhancements up to 41.8% in the acetone separation factor. The tie-line data consistency was confirmed by the Othmer–Tobias and the Hand equations. Moreover, the nonrandom two-liquid model of activity coefficient was applied satisfactorily to reproduce the equilibrium data with a root-mean-square deviation of only 1.95%.     

氨基功能型离子液体吸收CO2的性能

氨基功能型离子液体在常温常压下对CO₂具有较强的吸收选择性能,在分离固定CO₂方面具有较好的应用前景。合成了4种氨基功能型离子液体,对产物进行了IR和¹H NMR表征,探究了这些功能型离子液体的CO₂吸收性能及再生性能。结果表明,4种氨基功能型离子液体均具有强于常规型离子液体的CO₂吸收性能,再生性能良好,可循环使用;离子液体的CO₂溶解度受黏度影响显著,随吸收温度的升高而降低,随吸收压力的升高,吸收剂浓度的增加而增大;强化传质能提高再生效率,多次的再生对离子液体的吸收性能没有明显影响。     

基于COSMO-RS模型研究基团修饰[EMIM][OAC]的离子液体对乙腈-水汽液平衡的影响

以1-乙基-3-甲基咪唑醋酸盐([EMIM][OAC])为基准,通过分别在阴阳离子上修饰胺基(-NH₂)、羟基(-OH)、腈基(-CN)、卤素(Br、F)等,虚拟设计了15 种阳离子和21 种阴离子组成的离子液体(IL)。采用基于COSMO-RS 模型的COSMOthermX 软件计算了所设计的离子液体对乙腈-水混合物恒压汽液相平衡的影响,探索了修饰基团的种类、离子液体结构对乙腈相对挥发度的影响规律。研究发现,在阳离子碳链上修饰-NH₂,阴离子(醋酸根和丙酸根)羰基的邻碳上进行单一的-OH 修饰能促进乙腈与水的分离,且阳离子修饰的-NH₂ 数越多,促进分离的效果越明显,其他嫁接方式未取得好的分离效果。虚拟设计的两种阳离子(1-胺乙基-3-甲基咪唑、2,2,2-三胺乙基-3-甲基咪唑)与3 种阴离子(羟基乙酸、2-羟基丙酸、2-羟基-3-胺基丙酸)组合的离子液体分离效果明显比[EMIM][OAC]好。     

SEPARATION OF AROMATIC AND ALIPHATIC HYDROCARBONS WITH IONIC LIQUIDS

Naphtha cracker feeds may contain 10-25 wt% aromatic compounds. Removal of these aromatic compounds from the feed to the cracker would offer several advantages: higher capacity, higher thermal efficiency, and less coke formation. In this work, we investigated the separation of toluene from heptane by extraction with ionic liquids.

Several ionic liquids are suitable for extraction of toluene from toluene/heptane mixtures. The selectivities for the aromatic/aliphatic hydrocarbon separation with all ionic liquids tested increase with decreasing aromatic content in the feed. The toluene/heptane selectivities at 10% toluene in the feed at T = 40°C and 75°C with several ionic liquids ([emim]HSO₄, [mmim] methylsulfate, [emim] ethylsulfate, [bmim]BF₄, [emim] tosylate, [mebupy]BF₄, and [mebupy] methylsulfate) are a factor of 1.5-2.5 higher than those obtained with sulfolane, which is a conventional solvent for the extraction of aromatic hydrocarbons from a mixed aromatic/aliphatic hydrocarbon stream. The three most suitable ionic liquids from the ionic liquids tested for the separation of aromatic and aliphatic hydrocarbons are [mebupy]BF₄, [mebupy]CH₃SO₄, and [bmim]BF₄ and at 75°C also [emim] tosylate. The ionic liquid [mebupy]BF₄ is selected for further testing in our extraction pilot plant.

Because ionic liquids have a negligible vapor pressure, evaporating the extracted hydrocarbons from the ionic liquid phase could achieve the recovery of the ionic liquid. A conceptual process scheme for the extraction has been set up. Preliminary calculations show that both the investment costs and the energy costs will be considerably lower with ionic liquids than with sulfolane as the solvent.     

离子液体支撑液膜的CO2/CH4分离性能

由于离子液体对CO₂具有较好的溶解选择性,离子液体支撑液膜分离CO₂越来越受到关注。比较了含3种不同阴离子的常规离子液体([bmim][BF₄]、[bmim][PF₆]、[bmim][Tf₂N])作为支撑液膜的液膜相分离CO₂/CH₄的性能,考察了咪唑环上烷基链长对离子液体支撑液膜性能的影响。考虑向离子液体中引入胺基和羧基等亲CO₂基团,制备了1-丁基-3-甲基咪唑丙氨酸离子液体([bmim][β-Ala]),考察了 [bmim][β-Ala]支撑液膜分离CO₂/CH₄的性能,并对在CO₂渗透测试前后的支撑液膜进行了FT-IR分析,发现氨基酸离子液体中的-NH₂和CO₂的较强作用以及该离子液体的高黏性影响了CO₂的透过性,使[Bmim][β-Ala]支撑液膜的CO₂透过率低。     

液体酸耦合体系催化C4烷基化研究进展

综述了近十年来液体酸耦合体系催化C₄烃烷基化反应的最新进展,包括液体超强酸、有机酸-杂多酸、离子液体-酸耦合体系,对比了不同催化体系催化C₄烃烷基化反应过程中的烯烃转化率、三甲基戊烷的选择性和烷基化汽油的研究法辛烷值,总结了不同催化体系的优缺点。重点论述了离子液体-酸耦合体系催化剂中组成离子液体的阴阳离子以及耦合酸类型对C₄烃烷基化反应的影响：有机胺类离子液体较咪唑类有着更为优异的烷基化效果,阴离子和改性离子液体通过形成特定的结构来维持反应体系的酸强度、减少副反应,从而延长催化剂的使用寿命,耦合酸为反应提供酸性位点并与离子液体协同催化。离子液体-酸耦合催化体系具有酸耗低、稳定性好、不易失活且可循环使用等优点,是C₄烷基化催化剂未来的发展方向之一。