太阳能光伏光热一体化系统的实验研究

为提高太阳能的利用率同时得到可资利用的热水和电力，将小型贮能式光伏系统与家用平板型太阳能热水器结合起来，把光优电池组件层压在热水器的扁盒式铝合金集热板上，构成一套光优光热(PV／T)一体化系统，并在合肥地区进行了自然循环模式下的光电光热性能测试。实验结果表明，在晴朗或多云的天气条件下实验系统日平均热效率可达40％，日平均发电效率约9．5％，系统综合性能效率多在60％以上，比单独的光伏或热水系统效率有显著提高。     

Empirical study on thermal performance through separating impacts from a hybrid PV/TE system design integrating heat sink

A hybrid system design integrating a thermoelectric (TE) module has recently represented the advanced photovoltaic (PV) prototype with promoted efficiency for utilizing solar energy from the surroundings. Our present work during development of such a hybrid PV/TE system evaluates the thermal behaviors and the cooling performance associated with when integrating TE and heat sink modules. It has been noticed that a more effective structure through combining a heat sink with a TE module profits heat dissipation by cooling down the whole cell by ~ 8 °C, wherein the TE module itself demonstrates the cooling performance by ~ 27% enhancement in addition to its conventional role for electricity generation. Therefore, the PV/TE with a proper design can be used as a passive method for improving the cell efficiency as well as alleviating hot spot, which is typically occurring when the cell is unevenly heated during its operation. These results could be useful for further advancement on stability of power generation of a hybrid PV/TE system and may also be important for developing high-powered light emit diode.     

Evaluation of solar aided thermal power generation with various power plants

Solar aided power generation (SAPG) is an efficient way to make use of low or medium temperature solar heat for power generation purposes. The so‐called SAPG is actually ‘piggy back’ solar energy on the conventional fuel fired power plant. Therefore, its solar‐to‐electricity efficiency depends on the power plant it is associated with. In the paper, the developed SAPG model has been used to study the energy and economic benefits of the SAPG with 200 and 300 MW typical, 600 MW subcritical, 600 MW supercritical, and 600 and 1000 MW ultra‐supercritical fuel power units separately. The solar heat in the temperature range from 260 to 90°C is integrated with above‐mentioned power units to replace the extraction steam (to preheat the feedwater) in power boosting and fuel‐saving operating modes. The results indicate that the benefits of SAPG are different for different steam extracted positions and different power plants. Generally, the larger the power plant, the higher the solar benefit if the same level solar is integrated. Copyright © 2010 John Wiley & Sons, Ltd.     

Exergetic analysis of solar concentrator aided natural gas fired combined cycle power plant

This article deals with comparative energy and exergetic analysis for evaluation of natural gas fired combined cycle power plant and solar concentrator aided (feed water heating and low pressure steam generation options) natural gas fired combined cycle power plant. Heat Transfer analysis of Linear Fresnel reflecting solar concentrator (LFRSC) is used to predict the effect of focal distance and width of reflector upon the reflecting surface area. Performance analysis of LFRSC with energetic and exergetic methods and the effect, of concentration ratio and inlet temperature of the fluid is carried out to determine, overall heat loss coefficient of the circular evacuated tube absorber at different receiver temperatures. An instantaneous increase in power generation capacity of about 10% is observed by substituting solar thermal energy for feed water heater and low pressure steam generation. It is observed that the utilization of solar energy for feed water heating and low pressure steam generation is more effective based on exergetic analysis rather than energetic analysis. Furthermore, for a solar aided feed water heating and low pressure steam generation, it is found that the land area requirement is 7 ha/MW for large scale solar thermal storage system to run the plant for 24 h.     

Life cycle assessment study of solar PV systems: An example of a 2.7 kWp distributed solar PV system in Singapore

In life cycle assessment (LCA) of solar PV systems, energy pay back time (EPBT) is the commonly used indicator to justify its primary energy use. However, EPBT is a function of competing energy sources with which electricity from solar PV is compared, and amount of electricity generated from the solar PV system which varies with local irradiation and ambient conditions. Therefore, it is more appropriate to use site-specific EPBT for major decision-making in power generation planning. LCA and life cycle cost analysis are performed for a distributed 2.7 kW_p grid-connected mono-crystalline solar PV system operating in Singapore. This paper presents various EPBT analyses of the solar PV system with reference to a fuel oil-fired steam turbine and their greenhouse gas (GHG) emissions and costs are also compared. The study reveals that GHG emission from electricity generation from the solar PV system is less than one-fourth that from an oil-fired steam turbine plant and one-half that from a gas-fired combined cycle plant. However, the cost of electricity is about five to seven times higher than that from the oil or gas fired power plant. The environmental uncertainties of the solar PV system are also critically reviewed and presented.     

A novel hybrid photovoltaics/thermoelectric cooler distillation system

In this paper, a novel hybrid photovoltaics/thermoelectric cooler (PV/TEC) distillation system has been introduced. The limitation for distillation system working under hot arid climate is the heat removal required for the condensation process. The novelty of the proposed system is that it utilizes TEC to improve the condensation process. The proposed system composed of two porous layers separated by an air gap. The upper porous layer is installed at the back of a PV module; the lower porous layer is installed at the top of a TEC modules layer. This system can provide the demand of electricity and potable water for those people who live in rural areas (using one unit or more). The proposed system prevents PV module from overheating and actively enhancing the condensation process of the evaporated water. A steady‐state mathematical model has been proposed. This model was solved and simulated by equation solver software. Wind speed, solar radiation, and ambient temperature effect on the system performance were simulated and discussed. Results showed that the maximum productivity of the system reached an ambient temperature of 298 K, solar radiation of 1000 W/m² and wind speed of 5.5 m/s. The maximum yield of the system was 4.2 kg of distilled water per day with a net electrical output power of 73 W with an overall efficiency of 57.9% and PV cell efficiency of 12.32%.     

集成太阳能辅助供热的600 MW高背压热电联产机组的运行及优化

为了解决太阳能辅助燃煤发电系统与太阳能辅助抽汽供热系统的余热损失增多问题,提出一种太阳能辅助高背压热电联产系统的优化改造方案。利用EBSILON软件采用数值模拟的方法,对改造前后机组的整体性能和改造后机组在不同发电功率、背压、热网供回水温度工况下的收益变化进行了分析,对比了改造前后机组的(火用)效率与经济性差异。结果表明：改造后的太阳能辅助高背压热电联产系统节煤更多,机组回收了集成太阳能产生的余热后供热能力增强;改造后的机组在低发电功率、较高背压和较低热网供回水温度时节煤更多;在低发电功率、较低背压及较高热网供回水温度时机组的供热能力更强;改造后的太阳能辅助高背压热电联产系统(火用)效率更高、系统的经济效益更佳。     

Performance evaluation of solar photovoltaic/thermal systems

The major purpose of the present study is to understand the performance of an integrated photovoltaic and thermal solar system (IPVTS) as compared to a conventional solar water heater and to demonstrate the idea of an IPVTS design. A commercial polycrystalline PV module is used for making a PV/T collector. The PV/T collector is used to build an IPVTS. The test results show that the solar PV/T collector made from a corrugated polycarbonate panel can obtain a good thermal efficiency. The present study introduces the concept of primary-energy saving efficiency for the evaluation of a PV/T system. The primary-energy saving efficiency of the present IPVTS exceeds 0.60. This is higher than for a pure solar hot water heater or a pure PV system. The characteristic daily efficiency η_s* reaches 0.38 which is about 76% of the value for a conventional solar hot water heater using glazed collectors (η_s*=0.50). The performance of a PV/T collector can be improved if the heat-collecting plate, the PV cells and the glass cover are directly packed together to form a glazed collector. The manufacturing cost of the PV/T collector and the system cost of the IPVTS can also be reduced. The present study shows that the idea of IPVTS is economically feasible too.     

Research on the influence of PV cell to thermal characteristics of photovoltaic/thermal solar system

In the paper, we analyzed internal thermal transmission characteristics of water‐heating photovoltaic/thermal (PV/T) solar collector covered by photovoltaic (PV) cell, established photothermal conversion model of PV/T solar system, and analyzed the influence of PV cell coverage to photothermal characteristics of PV/T solar system. Results show that the thermal efficiency of PV/T solar system by optimizing PV cells coverage can reach 68%. In addition, by designing four water‐heating PV/T solar system prototypes with PV cell coverage of 0.4, 0.56, 0.7, and 0.82, respectively, we conducted experimental researches for the four prototypes and found that the four prototypes can achieve thermal efficiencies of 58%, 51%, 64%, and 67%, respectively, in heating 250 L of water to 50°C. The experiment results are consistent with theoretical analysis results, indicating that it is feasible to improve thermal characteristics of PV/T solar system by optimizing PV cell coverage. Copyright © 2017 John Wiley & Sons, Ltd.     

Thermodynamic performance analysis of the coal‐fired power plant with solar thermal utilizations

A new way of energy saving for existing coal‐fired power plant that uses low‐or medium‐temperature solar energy as assistant heat source was proposed to generate ‘green’ electricity. This paper has built the mathematical models of the solar‐aided power generation system focusing on the NZK600‐16.7/538/538 units. Based on the combination of the first and second law of thermodynamics, the thermodynamic performance of different components of the integrated system was evaluated under the changing operating condition aiming at different substitution options for turbine bleed streams. It has been found that the efficiency of the solar heat to electricity enhances with the increase of the load and the replaced extraction level. Additionally, when the second extraction is replaced, the effect is the best, which makes the power output increase around 6.13% or the coal consumption rate decrease 13.14 g/(kW · h) under 100%THA load and CO₂ emission reduce about 32.76 g/(kW · h), while the energy and exergy efficiencies of the integrated system are 39.35% and 39.12%, respectively. The results provide not only theory basis and scientific support for the design of solar‐aided coal‐fired power plants, but also a new way of energy saving and optimization for the units. Copyright © 2014 John Wiley & Sons, Ltd.     

Performance of solar cells using thermoelectric module in hot sites

The ambient temperature at Madinah site is between 40 °C and 50 °C during the summer months and sometimes is over 50 °C. The cell temperature reaches the value of 83 °C. This affects the behaviors of solar cells (SC) and decreases their efficiency. The performance of solar cells is presented in this work using thermoelectric module (TEM) as cooling system. In fact, we have found experimentally that the efficiency of solar cells decreases with increase in its temperature. The efficiency of solar cells drops by 0.5% per °C rise in temperature. So, it's necessary to operate them at lower temperature in order to increase their efficiency. Cooling the solar cells would enhance its performance. The hybrid PV/TEM system is proposed for PV applications in hot sites.     

Integrated solar combined cycle system with steam methane reforming: Thermodynamic analysis

The present paper considers an integrated solar combined cycle system (ISCCS) with an utilization of solar energy for steam methane reforming. The overall efficiency was compared with the efficiency of an integrated solar combined cycle system with the utilization of solar energy for steam generation for a steam turbine cycle. Utilization of solar energy for steam methane reforming gives the increase in an overall efficiency up to 3.5%. If water that used for steam methane reforming will be condensed from the exhaust gases, the overall efficiency of ISCCS with steam methane reforming will increase up to 6.2% and 8.9% for β = 1.0 and β = 2.0, respectively, in comparison with ISCCS where solar energy is utilized for generation of steam in steam turbine cycle. The Sankey diagrams were compiled based on the energy balance. Utilization of solar energy for steam methane reforming increases the share of power of a gas turbine cycle: two-thirds are in a gas turbine cycle, and one-third is in a steam turbine cycle. In parallel, if solar energy is used for steam generation for a steam turbine cycle, than the shares of power from a gas and steam turbine are almost equal.     

Thermal analysis of PV/T evaporator of a solar-assisted heat pump

The performance of photovoltaic/thermal (PV/T) solar collector had been studied theoretically and experimentally for some years. Air and water streams were used as the heat carriers for space heating or services hot water systems. The cooling effect allows the PV module to work at lower temperature and its PV efficiency is therefore improved. However, such an advantage diminishes when the solar irradiance is high. To improve the situation a new type of PV/T collector is proposed. It works as the evaporator of a heat pump, in that refrigerant evaporates in the tubing at the back of the flat-plate collector and the PV module is adhered to the front surface. Mathematical models were developed to simulate the complex energy conversion processes. Numerical analysis was then performed based on the distributed parameters approach. An experimental rig was also built to test its real performance. Our results showed that the PV/T evaporator had an overall efficiency in the range of 0.64–0.87, thermal efficiency 0.53–0.64 and PV efficiency 0.124–0.135. The simulation results were found in good agreement with the experiment measurements. Copyright © 2006 John Wiley & Sons, Ltd.     

Energy performance of water hybrid PV/T collectors applied to combisystems of Direct Solar Floor type

The integration of photovoltaic (PV) modules in buildings allows one to consider a multifunctional frame and then to reduce the cost by substitution of components. In order to limit the rise of the cell operating temperature, a photovoltaics/thermal (PV/T) collector combines a solar water heating collector and PV cells. The recovered heat energy can be used for heating systems and domestic hot water. A combination with a Direct Solar Floor is studied. Its low operating temperature level is appropriate for the operating conditions of the mono- or poly-crystalline photovoltaic modules which are selected in that study. However, for a system including a glass covered collector and localised in Mâcon area in France, we show that the annual photovoltaic cell efficiency is 6.8% which represents a decrease of 28% in comparison with a conventional non-integrated PV module of 9.4% annual efficiency. This is obviously due to a temperature increase related to the cover. On the other hand, we show that without a glass cover, the efficiency is 10% which is 6% better than a standard module due to the cooling effect.Moreover, in the case of a glazed PV/T collector with a conventional control system for Direct Solar Floor, the maximum temperature reached at the level of the PV modules is higher than 100 °C. This is due to the oversize of the collectors during the summer when the heating needs are null, i.e. without a heated swimming pool for example. This temperature level does not allow the use of EVA resin (ethylene vinyl acetate) in PV modules due to strong risks of degradation. The current solution consists of using amorphous cells or, if we do not enhance the thermal production, uncovered PV/T collector. Further research led to water hybrid PV/T solar collectors as a one-piece component, both reliable and efficient, and including the thermal absorber, the heat exchanger and the photovoltaic functions.     

无盖板型水冷式PV/T模块光电/光热综合性能实验研究

无盖板PV/T组件相比于盖板式PV/T组件有更高的光电转换效率,在电能输出方面的优势明显。基于此,提出一种无盖板型水冷式PV/T模块,并搭建由光伏对比模块、水冷式PV/T模块以及无冷却水循环的PV/T对比模块构成的实验平台开展对比实验,研究温度、流量对无盖板PV/T模块电、热转换效率的影响。结果表明,在水冷作用下,PV/T模块的光伏组件温度显著降低,与PV/T对比模块相比发电效率提升11.54%;环境平均温度为21.7 ℃、平均辐照度650 W/m²的测试条件下,流量0.12 m³/h时模块的电效率为17.44%,热效率为19.80%,综合效率达到65.69%,考虑到循环泵消耗的电能,表面积1.93 m²的水冷式PV/T模块全天可存储有效能3.72 MJ。     

Theoretical and experimental study on the application of diffuse‐reflection concentrators in PV/T solar system

In order to improve the practicability of PV/T solar system, we proposed the theory and method on the application of diffuse‐reflection concentrator in the PV/T solar system and analyzed the concentration characteristics of this proposed application. In addition, we designed experimental prototype of PV/T solar system and conducted test and analysis of the thermal and electrical characteristics of the PV/T solar system with or without a concentrator, respectively. The results showed that for the PV/T solar system with diffuse‐reflection concentrator, the amount of incident irradiance was increased by an average of 26% during test period, and the 200‐L water in the system was heated to 58 °C, which was 12 °C higher than that of PV/T solar system without diffuse‐reflection concentrator; moreover, the max output power was increased by 11%. Therefore, it is a feasible way to improve the practicability of PT/V solar system by integrating a diffuse‐reflection concentrator. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of high irradiation on photovoltaic power and energy

Solar photovoltaics (PV) is a promising solution to combat against energy crisis and environmental pollution. However, the high manufacturing cost of solar cells along with the huge area required for well‐sized PV power plants are the two major issues for the sustainable expansion of this technology. Concentrator technology is one of the solutions of the abovementioned problem. As concentrating the solar radiation over a single cell is now a proven technology, so attempt has been made in this article to extend this concept over PV module. High irradiation intensity from 1000 to 3000 W/m² has been investigated to measure the power and energy of PV cell. The numerical simulation has been conducted using finite element technique. At 3000 W/m² irradiation, the electrical power increases by about 190 W compared with 63 W at irradiation level of 1000 W/m². At the same time, at 3000 W/m² irradiation, the thermal energy increases by about 996 W compared with 362 W at 1000 W/m² irradiation. Electrical power and thermal energy are enhanced by about 6.4 and 31.3 W, respectively, for each 100‐W/m² increase of solar radiation. The overall energy is increased by about 179.06% with increasing irradiation level from 1000 to 3000 W/m². It is concluded that the effect of high solar radiation using concentrator can significantly improve the overall output of the PV module.     

Thermal management of solar photovoltaics modules for enhanced power generation

Industry and government interest in solar energy has increased in recent years in the Middle East. However, despite high levels of solar irradiance in the Arabian Gulf, harsh climatic conditions adversely affect the electrical performance of solar photovoltaics (PV). The objective of this study is to compare the annual performance characteristics of solar PV modules that utilize either sun-tracking or water cooling to increase electrical power generation relative to that of stationary, passively cooled modules in the Middle East climatic conditions. This is achieved using an electro-thermal model developed and validated against experimental data acquired in this study. The model is used to predict the annual electrical power output of a 140 W PV module in Abu Dhabi (24.43°N, 54.45°E) under four operating conditions: (i) stationary geographical south facing orientation with passive air cooling, (ii) sun-tracked orientation with passive air cooling, (iii) stationary geographical south facing orientation with water cooling at ambient air temperature, and (iv) stationary geographical south facing orientation with water refrigerated at either 10 °C or 20 °C below ambient air temperature. For water cooled modules, annual electrical power output increases by 22% for water at ambient air temperature, and by 28% and 31% for water refrigerated at 10 °C and 20 °C below ambient air temperature, respectively. 80% of the annual output enhancement obtained using water cooling occurs between the months of May and October. Finally, whereas the annual yield enhancement obtained with water cooling at ambient air temperature from May to October is of 18% relative to stationary passive cooling conditions, sun-tracking over the complete year produces an enhancement of only 15% relative to stationary passive cooling conditions.     

光伏光热一体化组件性能实验探究与分析

通过搭建PV/T一体化组件性能测试实验台,测试在不同进口水温、不同一体化组件倾角和不同流量时PV/T一体化组件的热、电效率。结果表明,在进口水温30℃工况下一体化组件拥有最优的热效率值和输出电功率值,其日总热效率为35.97%,对应的输出电功率范围为29.40~30.51 W;45°倾角放置的一体化组件可接收到较多的太阳辐照度,且具有最优的光热性能,对应的日总热效率为32.65%;流量85 L/h工况下一体化组件拥有最优的热效率值,对应的日总热效率值为25.89%,串联50Ω电阻时组件的输出电功率随流量的增大而增大,但变化较小,流量120 L/h工况下一体化组件拥有最优的输出电功率值,对应的输出电功率值范围为24.02~29.19 W。     

Highly integrated post‐combustion carbon capture process in a coal‐fired power plant with solar repowering

While post‐combustion carbon capture (PCC) technology has been considered as the ready‐to‐retrofit carbon capture solution, the implementation of the technology remains hampered by high costs associated with the large energy penalty incurred by solvent regeneration. This paper presents a highly integrated PCC process for a coal‐fired power plant with solar repowering that features significantly enhanced energy efficiency. Validated process models are developed for the power, capture, and solar thermal plants and simulated in a model superstructure to evaluate the possible improvements in power plant energy efficiency and power output penalty reductions. A 660‐MW power plant is taken as the case study. Three cases are used in this simulation analysis: (a) base case consisting of 660‐MW power plant integrated with a PCC plant, (b) the base case extended to incorporate solar repowering, and (c) a highly integrated case that extends on the previous case to include CO₂ gas compression unit heat integration. This study also highlights and discusses the role and interaction of various PCC and solar plant variables (e.g., solar field size, steam extraction flow rate, and twin LP turbine pressures) in the integration with power plant parameters. In particular, the power plant deaerator conditions play an important role in determining the total solar thermal energy required from the solar plant, thus dictating the solar field size. Copyright © 2015 John Wiley & Sons, Ltd.