Effect of exhaust gas recirculation on a nanoparticle-doped biodiesel- and diesel-blends-fuelled diesel engine

ABSTRACT

This work investigates the effect of adding Cerium oxide nanoparticles at different proportions (30, 60 and 90?ppm) to Calophyllum inophyllum methyl ester and diesel blends (20% CI methyl ester and 80% diesel) in a four-stroke single-cylinder diesel engine. Addition of nanoparticles is a strategy to reduce emission and to improve the performance of the biodiesel. Modified fuels are introduced into the engine by admitting exhaust gas recirculation (EGR) at a rate of 10% and 20% so as to reduce nitrogen oxide (NO_X) emissions from biodiesel and diesel blends. Results revealed a significant reduction in emissions (CO, NO_X, HC and Smoke) at a 10% EGR rate. However, brake thermal efficiency is reduced with an increase in brake-specific fuel consumption at higher EGR rates. Hence, it is observed that 10% EGR rate is an effective method to control the emission of biodiesel and diesel blends without compromising much on engine efficiency.     

Experimental investigation of performance,combustion and emission characteristics of CI engine fuelled with chicha oil biodiesel

As the decreasing availability of the fossil fuel is rising day by day, the search of alternate fuel that can be used as a substitute to the conventional fuels is rising rapidly. A new type of biofuel, chicha oil biodiesel, is introduced in this work for the purpose of fuelling diesel engine. Chicha oil was transesterified with methanol using potassium hydroxide as catalyst to obtain chicha oil methyl ester (COME). The calorific value of this biodiesel is lower, when compared to that of diesel. The COME and their blends of 20%, 40%, 60% and 80% with diesel were tested in a single cylinder, four stroke, direct injection diesel engine and the performance, combustion and emission results were compared with diesel. The test result indicates that there is a slight increase in brake thermal efficiency and decrease in brake-specific fuel consumption for all blended fuels when compared to that of diesel fuel. The use of biodiesel resulted in lower emissions of CO and HC and increased emissions of CO₂ and NO_x. The experimental results proved that the use of biodiesel (produced from chicha oil) in compression ignition engine is a viable alternative to diesel.     

Performance and emission characteristics of direct injection diesel engine using linseed oil as biodiesel by varying injection timing

The depletion of fossil fuels and increasing demand leads to research in alternate fuels. The alternate fuels are bio-degradable, renewable and non-toxic. Many types of oils are re-used in biodiesel production, considering their availability, among which linseed oil is the most significant one. Injection timing plays a major role among various injection parameters which affects its performance and emission characteristics. This paper focuses on experimental investigation on a single cylinder, four-stroke direct injection diesel engine with output of 5.2?kW at 1500?rpm at various injection timings, 20, 23, 26 degree BTDC for observing the performance and emission characteristics of direct injection diesel engine using methyl esters of linseed oil and its blends. The blends are B10, B20, and fuel characteristics are observed. The results show that when compared with diesel it gives an increase in BTHE and reduction in SFC. Both the biodiesel blends give lesser NOx. Slightly higher CO and HC emission were found. The performance and emissions were increased in when injection increased.     

Bio-ethanol additive effect on direct injection diesel engine performance,emission and combustion characteristics – an experimental examination

ABSTRACT

The present investigation explores the effect of dairy scum oil methyl ester (DSOME) blends and ethanol additive on TV1 Kirloskar diesel engine performance, combustion and emission characteristics. From the experimental study, it is concluded that DSOME-B20 (20% dairy scum biodiesel?+?80% diesel) has shown appreciable performance and lower HC and CO emissions among all other blends. Hence DSOME-B20 is optimised as best fuel blend and it is carried for further investigations to study the effect of bio-ethanol additive on diesel engine performance. From the study it apparent that diesel engine operated with ethanol additive and 20% dairy scum biodiesel blended fuels shown the satisfactorily improved emission characteristics when compared to petroleum diesel fuel operation. Finally, from the experimental investigation, it concludes that addition of ethanol shown the slightly higher HC, CO emission and improved BTE, BSFC, NOx and CO₂ than sole B20 biodiesel blend. Among all three (3%, 6% and 9%) ethanol additive ratios, E6% (6%-ethanol with B20) ethanol additive exhibits slightly better BTE, BSFC, cylinder pressure and heat release rate hence 6% ethanol additive with B20 biodiesel blend would furnish beneficial effects in the diesel engine.     

Energy consumption and exhaust emissions in mechanized timber harvesting operations in Sweden

The study presents an estimation of the energy input and the amount of emissions to air due to fuel, chainsaw and hydraulic oil consumption by heavy duty diesel engine vehicles operating in forest logging operations in Sweden. Exhaust concentrations are given for carbon dioxide, carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter. Three fuel types (rapeseed methyl ester, environmental class 1 and environmental class 3 diesel fuels) and two types of lubricating base oil (mineral- and vegetable-based) were examined. Energy input per unit of timber production (m3ub) was 82 MJ, 11% of which was due to energy consumption during the production phase of the fuel. Emissions during the whole life cycle of the fuels and the base oils are included in the study. The highest CO2 and NOx emissions occurred when rapeseed methyl ester was used as fuel together with rapeseed as base oil for chainsaw and hydraulic oil. The highest HC and CO emissions occurred when environmental class 3 diesel fuel was used.     

A comparative study of performance and combustion characteristics of a CI diesel engine fuelled with B20 biodiesel blends

This paper aims to study the diesel engine performance and combustion characteristics fuelled with Banalities aegyptiaca oil methyl ester, palm oil methyl ester, sesame methyl ester oil, rapeseed methyl ester oil, soybean oil methyl ester and diesel fuel. In this present work, only 20% of each biodiesel blends was tested in diesel engine; stated that the possible use of biodiesel of up to 20% in a diesel engine without modification in literature. A single-cylinder, auxiliary water-cooled and computer-based variable compression ratio diesel engine was used to evaluate their performance at constant speed and at measured load conditions. The performance and combustion tests are conducted using each of the above test fuels, at a constant speed of 5000?rpm. Thus, the varying physical and chemical properties of test fuels against pure diesel are optimised for better engine performance.

Abbreviations: BP: brake power; BSFC: brake-specific fuel consumption; BTE: brake thermal efficiency; CO: carbon monoxide; CP: cylinder pressure; DP: diesel pressure; EGT: exhaust gas temperature; HC: hydrocarbon; HRR: heat release rate; NO _x : nitric oxides; PM: particulate matter; TDC: top dead centre; VCR: variable compression ratio     

Evaporation rate and engine performance analysis of coated diesel engine using Raphanus sativus biodiesel and its diesel blends

An experimental investigation to measure the evaporation rates, PSZ-coated engine performance and emissions of radish biodiesel (Methyl Ester of radish oil) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat radish biodiesel, neat diesel and their bends have been measured under slow convective environment of air velocity of 0.2?m/s with a constant temperature of 200°C. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilised in a test engine with different load conditions to evaluate the performance and emission characteristics of the fuels. From the observed evaporation, performance and emissions characteristics, it can be suggested that a blend of B25–B75 could be optimally used in coated diesel engine settings without any modifications on it.     

Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Performance and emission characteristics of cashew nut shell oil on the CI engine

This article is an effort to address the need for a non-cooking oil-based biodiesel. Here, the experimental work is done on a single cylinder, direct injection CI engine using cashew nut shell oil biodiesel blends under constant speed. The cashew nut shell liquid (CNSL) biodiesel is blended with the diesel fuel and used as biodiesel blend. Blends used for testing are B20, B40 and B60. The effect of the fuels on engine power, brake thermal efficiency (BTE) and exhaust gas temperature was determined by performance tests. The influences of blends on CO, CO₂, HC and NO_x emissions were investigated by emission tests. The BTE values of biodiesel are closer to diesel. Compared to diesel, all the biodiesel blends gave lesser unburnt hydrocarbon (HC), carbon monoxide (CO) and smoke emissions. Slightly higher NO_x emissions were found in CNSL biodiesel blends, which is typical of the other biodiesels.     

Impact of partially stabilised zirconia on a single-cylinder diesel engine’s performance,using orange oil methyl ester biodiesel

Exhaustion of crude oil resources, rise in fuel prices and necessity to find less-carbon fuel have encouraged to find an alternative fuel. Biodiesel is characterised by its fuel properties, which may have an adverse effect on performance and emission characteristics of the engine. Thus, it is necessary to trans-esterify the extracted orange oil and make it viable for diesel engine. In the present work, partially stabilised zirconia was used as a thermal barrier coating (TBC) for the combustion chamber components using plasma spray technique. The present study focused on the impact of TBC on performance and emission characteristics of a diesel engine with B1 (20% orange oil methyl ester with 80% diesel) sample and diesel. Increased brake thermal efficiency and reduced brake-specific fuel consumption are observed for B1 in the TBC engine. On comparing with the uncoated engine, the B1 in coated engine exhibited lower carbon monoxide, hydrocarbon, oxides of nitrogen and smoke emissions than diesel.     

A characteristic evaluation of alumina–zirconia-coated engine fuelled with punnai methyl ester

All these years, several studies have been carried out to find feasible, viable and dominant alternate source to fossil fuels, with the primary interest of enhancing engine performance and reducing exhaust tail pipe emissions. The present work enumerates the performance and emission characteristics of low-heat rejection engine (LHRE) coated with the alumina–zirconia (Al₂O₃–ZrO₂) composite. Experimental results proved improvement in brake thermal efficiency, brake-specific fuel consumption and well-to-wheel reduction of carbon monoxide, hydrocarbon and smoke emission for coated engine (CE) in comparison with uncoated engine (UCE). Neat diesel, new high-potential punnai methyl ester and its diesel blends were used as test fuels. However, in the experimental study, oxides of nitrogen increased for CE than UCE.     

Combustion characteristics of the direct injection diesel engine fuelled with corn oil methyl ester

Petroleum-based fuels is a finite resource that is rapidly depleting. Consequently, petroleum reserves are not sufficient enough to last many years. In this research, an experimental investigation has been performed to give insight into the potential of biodiesel as an alternative fuel for direct injection (DI) diesel engines. The experimental work has been carried out to estimate the combustion characteristics of a single-cylinder, four-stroke, DI diesel engine fuelled with corn oil methyl ester (COME) and diesel blends. The COME was preheated to temperatures namely 50°C, 70°C and 90°C before it was supplied to the engine. The optimised preheated temperature of 70°C was chosen based on the higher brake thermal efficiency and lower specific fuel consumption. The performance, emission and combustion characteristics are evaluated by running the engine with COME and diesel blends at this preheated temperature. In this paper, the combustion characteristics are only discussed. The combustion characteristics such as ignition delay, maximum rate of pressure, heat release rate, cumulative heat release rate, mass fraction burned and combustion duration of COME methyl ester and diesel were evaluated and compared with neat diesel. The rate of pressure rise and maximum combustion pressure inside the cylinder were high for COME blends compared with neat diesel. The heat release rate of diesel is higher compared with COME blends. The ignition delay and combustion duration are decreased for COME blends compared with neat diesel. The cumulative heat release rate and mass fraction burnt of COME blends are higher than neat diesel.     

Combustion characteristics of a DI diesel engine fuelled with blends of methyl ester of cotton seed oil

The combustion characteristics of a single-cylinder, four-stroke, air-cooled and direct injection (DI) diesel engine fuelled with methyl ester of cotton seed oil (MECSO) and its blends with neat diesel fuel were examined. The experiments were conducted at a constant speed under steady-state condition with a Kirloskar TAF 1 engine. Combustion characteristics such as cylinder pressure, heat release rate (HRR), cumulative heat release rate (CHRR), maximum cylinder pressure, rate of pressure rise, ignition delay, duration of injection and combustion duration of MECSO and its blends with diesel were evaluated and compared with those of diesel fuel. From the analysis, it was found that the peak cylinder pressure and HRR of diesel were higher when compared with those of MECSO blends. The ignition delay, duration of injection and combustion duration decreased for MECSO blends compared to those of diesel. However, the CHRR of MECSO and its blends were higher than that of diesel. Finally, the study showed that B25 (25% of MECSO and 75% of diesel) gave optimum combustion characteristics for all loads and could be used as a viable alternative fuel in a DI diesel engine without any engine modifications.     

Impact of nano additive on engine characteristics using blends of thyme oil with diesel

Diesel engines have been the ‘primus motor’ of transportation in the world since a long time now. However, the depletion of fuel supplies, recent concerns over the environment and the ever-increasing fuel prices have made the search for an alternative fuel of paramount importance. A considerable amount of interest has been shown by researchers to evaluate different plant and vegetable oils as a replacement of diesel. Based on this background, an attempt to investigate Thyme oil as a substitute to diesel without any modifications in the engine was made. The experiment was conducted on a 1500?rpm, four-stroke, diesel engine with single cylinder which is water cooled. Cerium Oxide nano additive was added to the blends of thyme oil with diesel and its effects on the brake thermal efficiency, specific fuel consumption (SFC) and exhaust emissions were examined. The experimental results portrayed better values of brake thermal efficiency and low SFC with B10 (10 parts of oil with 90 parts of diesel) and B20 samples of the blends, while the B40 blend showed lower NO_x emissions at all loads. The HC content was found to increase with the increasing quantity of thyme oil in the blends.     

Experimental studies on the performance,emission and combustion characteristics of a biodiesel-fuelled (Pongamia methyl ester) diesel engine with diethyl ether as an oxygenated fuel additive

This paper investigates the combustion, performance and emission characteristics of a single-cylinder diesel engine using neat biodiesel (Pongamia methyl ester) with two different blends (10% and 15% diethyl ether [DEE]) at different load conditions. The measured values of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), exhaust gas temperature (EGT), carbon monoxide (CO), hydrocarbon (HC), nitrogen oxide (NO) and smoke were calculated and analysed and compared with diesel fuel. The results showed that a significant reduction in NO and smoke emissions for neat biodiesel with 15% DEE blend compared with neat biodiesel at full load conditions. The peak pressure and heat release rate were decreased, and maximum rate of pressure rise and ignition delay were also decreased with DEE blends at full load. On the whole, it is concluded that the biodiesel with 15% DEE blend showed better results with respect to efficiency and emissions point of view compared with biodiesel.     

Effect of Al2O3 nano-additives on the performance and emission characteristics of jatropha and pongamia methyl esters in compression ignition engine

Nano-additives can be added to biodiesel blends to improve its performance through better fuel properties. The present study investigated the effects of Al₂O₃ nano-additives on B20 blends of pongamia and jatropha biodiesel in a vertical single cylinder direct injection compression ignition engine. The fuel properties have been determined for all fuel samples with and without additives addition. The engine study was conducted to analyse the performance and emission characteristics of the blends with and without the additives at varying loads. The emissions from the biodiesel blends were comparatively lesser than that of normal diesel. B20 blend of pongamia biodiesel with additive has shown better performance. Additive-added biodiesel blends show a significant reduction in NO_x emission.     

Emissions characteristics of a diesel engine operating on biodiesel and biodiesel blended with ethanol and methanol

Euro V diesel fuel, pure biodiesel and biodiesel blended with 5%, 10% and 15% of ethanol or methanol were tested on a 4-cylinder naturally-aspirated direct-injection diesel engine. Experiments were conducted under five engine loads at a steady speed of 1800 r/min. The study aims to investigate the effects of the blended fuels on reducing NO_x and particulate. On the whole, compared with Euro V diesel fuel, the blended fuels could lead to reduction of both NO_x and PM of a diesel engine, with the biodiesel-methanol blends being more effective than the biodiesel-ethanol blends. The effectiveness of NO_x and particulate reductions is more effective with increase of alcohol in the blends. With high percentage of alcohol in the blends, the HC, CO emissions could increase and the brake thermal efficiency might be slightly reduced but the use of 5% blends could reduce the HC and CO emissions as well. With the diesel oxidation catalyst (DOC), the HC, CO and particulate emissions can be further reduced.     

Experimental investigation on mahua methyl ester blended with diesel fuel in a compression ignition diesel engine

In this article, the mahua tree’s high importance in the present-day plantations is described and the preparation of mahua methyl ester (MME) from the raw mahua seed oil by the two methods of the transesterification process is described. The tested physical properties were compared with the requirement of ASTM D-6751. The obtained MME and its blends of B20, B40, B60, and B80 were investigated in an unmodified diesel engine. From the results of the performance, it has been observed that brake-specific fuel consumption and brake thermal efficiency are slightly improved (B20 and B40) at part-load conditions and approach diesel at full-load conditions. From combustion analysis, it was seen that ignition delay was shorter for biodiesel and its blends compared with the diesel fuel. The emission characteristics of carbon monoxide, hydrocarbons, and smoke opacity were reduced for all the fuel blends, but at high temperatures they undergo an endothermic reaction and produced various oxides of nitrogen.     

Investigation of Sapindus seed biodiesel with nano additive on single cylinder diesel engine

ABSTRACT

In the agriculture and transportation sector, many bio-seed based biofuels have exposed to be a better replacement for fuels derivative from fossil fuels. In the Indian context, due to the energy needs, agricultural growth, surrounding degradation and rural development these biofuels have achieved an acknowledgment as an alternative. Biofuels derived from the bio seeds such as rubber seed oil, cottonseed oil, jatropha and rapeseed oil etc. can hold the carbon emissions from vehicles in an efficient and economical method. In this research paper, an attempt has been made with blends from bio-seed based Sapindus seed oil with nano additive as an alternative for diesel. Its performance and emission characteristics were investigated on the constant speed single cylinder CI engine and results were compared.     

Performance,combustion and emission characteristics of a single-cylinder constant speed compression ignition engine using soybean methyl esters

ABSTRACT

The present study was aimed to produce biodiesel from soybean oil and to investigate its characteristics. Soybean oil-based bio diesel properties are observed and tested in the fuel testing laboratory with standard procedures. It is found that soybean oil-based biodiesel has similar properties as that of diesel fuel. An experimental set-up was used in the study to analyse the performance, combustion and emission of soybean oil biodiesel with respect to normal diesel by using different blends (B20, B40, B60, B80 and B100). It is observed that there is no difficulty found in running the engine, but the performance of the biodiesel blends quite deviated from normal diesel. The combustion characteristics of the tested blends were in agreement with normal diesel. The carbon emissions are much lower for soybean oil biodiesel blends than diesel.