Water, vegetation and sediment gradients in submerged aquatic vegetation mesocosms used for low-level phosphorus removal

Gradients in phosphorus (P) removal and storage were investigated over 6 years using mesocosms (each consisting of three tanks in series) containing submerged aquatic vegetation (SAV) grown on muck and limerock (LR) substrates. Mean inflow total P concentrations (TP) of 32 μg L⁻¹ were reduced to 15 and 17 μg L⁻¹ in the muck and LR mesocosms, respectively. Mesocosm P loading rates (mean = 1.75 g m⁻² year⁻¹) varied widely during the study and were not correlated with outflow TP, which instead varied seasonally with lowest monthly mean values in December and January.The mesocosms initially were stocked with Najas guadalupensis, Ceratophyllum demersum, and Chara zeylanica, but became dominated by C. zeylanica. At the end of the study, highest vegetative biomass (1.1 and 1.4 kg m⁻² for muck and LR substrates) and tissue P content (1775 and 1160 mg kg⁻¹) occurred in the first tank in series, and lowest biomass (1.0 and 0.2 kg m⁻²) and tissue P (147 and 120 mg kg⁻¹) in the third tank. Sediment accretion rates (2.5, 1.9 and 0.9 cm yr⁻¹ on muck substrates), accrued sediment TP (378, 309 and 272 mg kg⁻¹), and porewater soluble reactive P (SRP) concentrations (40, 6 and 4 μg L⁻¹) in the first, second and third tanks, respectively, exhibited a similar decreasing spatial trend. Plant tissue calcium (Ca) near mesocosm inflow (19-30% dry weight) and outflow (23-26%) were not significantly different, and sediment Ca was also similar (range of 24 to 28%) among sequential tanks.Well-defined vegetation and sediment enrichment gradients developed in SAV wetlands operated under low TP conditions. While the mesocosm data did not reflect deterioration in treatment performance over 6 years, accumulation of P-enriched sediments near the inflow could eventually compromise hydraulic storage and P removal effectiveness of these shallow systems.     

Degradation of diclofenac by TiO2 photocatalysis: UV absorbance kinetics and process evaluation through a set of toxicity bioassays

In the present study the degradation kinetics and mineralization of diclofenac (DCF) by the TiO₂ photocatalysis were investigated in terms of UV absorbance and COD measurements for a wide range of initial DCF concentrations (5-80 mg L⁻¹) and photocatalyst loadings (0.2-1.6 g TiO₂ L⁻¹) in a batch reactor system. A set of bioassays (Daphnia magna, Pseudokirchneriella subcapitata and Artemia salina) was performed to evaluate the potential detoxification of DCF. A pseudo-first-order kinetic model was found to fit well most of the experimental data, while at high initial DCF concentrations (40 and 80 mg L⁻¹) and at 1.6 g TiO₂ L⁻¹ photocatalyst loading a second-order kinetic model was found to fit the data better. The toxicity of the treated DCF samples on D. magna and P. subcapitata varied during the oxidation, probably due to the formation of some intermediate products more toxic than DCF. Unicellular freshwater algae was found to be very sensitive to the treated samples as well as the results from D. magna test were consistent to those of algae tests. A. salina was not found to be sensitive under the investigated conditions. Finally, UV absorbance analysis were found to be an useful tool for a fast and easy to perform measurement to get preliminary information on the organic intermediates that are formed during oxidation and also on their disappearance rate.     

Temporal variations in arsenic uptake by rice plants in Bangladesh: The role of iron plaque in paddy fields irrigated with groundwater

The transfer of arsenic to rice grains is a human health issue of growing relevance in regions of southern Asia where shallow groundwater used for irrigation of paddy fields is elevated in As. In the present study, As and Fe concentrations in soil water and in the roots of rice plants, primarily the Fe plaque surrounding the roots, were monitored during the 4-month growing season at two sites irrigated with groundwater containing ∼ 130 μg l^− 1 As and two control sites irrigated with water containing < 15 μg l^− 1 As. At both sites irrigated with contaminated water, As concentrations in soil water increased from < 10 μg l^− 1 to > 1000 μg l^− 1 during the first five weeks of the growth season and then gradually declined to < 10 μg l^− 1 during the last five weeks. At the two control sites, concentrations of As in soil water never exceeded 40 µg l^− 1. At both contaminated sites, the As content of roots and Fe plaque rose to 1000-1500 mg kg^− 1 towards the middle of the growth season. It then declined to ∼ 300 mg kg^− 1 towards the end, a level still well above As concentration of ∼ 100 mg kg^− 1 in roots and plaque measured throughout the growing season at the two control sites. These time series, combined with simple mass balance considerations, demonstrate that the formation of Fe plaque on the roots of rice plants by micro-aeration significantly limits the uptake of As by rice plants grown in paddy fields. Large variations in the As and Fe content of plant stems at two of the sites irrigated with contaminated water and one of the control sites were also recorded. The origin of these variations, particularly during the last month of the growth season, needs to be better understood because they are likely to influence the uptake of As in rice grains.     

Comparison of toxicity and release rates of Cu and Zn from anti-fouling paints leached in natural and artificial brackish seawater

Biocide-containing anti-fouling paints are regulated and approved according to the added active ingredients, such as Cu. Biocide-free paints are considered to be less environmentally damaging and do not need an approval. Zn, a common ingredient in paints with the potential of causing adverse effects has received only minor attention. Laboratory experiments were conducted in artificial brackish seawater (ASW) and natural brackish seawater (NSW) to quantify release rates of Cu and Zn from biocide-containing and biocide-free labeled eroding anti-fouling paints used on commercial vessels as well as leisure boats. In addition, organisms from three trophic levels, the crustacean Nitocra spinipes, the macroalga Ceramium tenuicorne and the bacteria Vibrio fischeri, were exposed to Cu and Zn to determine the toxicity of these metals. The release rate of Cu in NSW was higher from the paints for professional use (3.2-3.6 µg cm⁻² d^− 1) than from the biocide leaching leisure boat paint (1.1 µg cm⁻² d^− 1). Biocide-free paints did leach considerably more Zn (4.4-8.2 µg cm⁻² d^− 1) than biocide-containing leisure boat paint (3.0 µg cm⁻² d^− 1) and ship paints (0.7-2.0 µg cm⁻² d^− 1). In ASW the release rates of both metals were notably higher than in NSW for most tested paints. The macroalga was the most sensitive species to both Cu (EC₅₀ = 6.4 µg l^− 1) and Zn (EC₅₀ = 25 µg l^− 1) compared to the crustacean (Cu, LC₅₀ = 2000 µg l^− 1 Zn, LC₅₀ = 890 µg l^− 1), and the bacteria (Cu, EC₅₀ = 800 µg l^− 1 and Zn, EC₅₀ = 2000 µg l^− 1). The results suggest that the amounts of Zn and Cu leached from anti-fouling paints may attain toxic concentrations in areas with high boat density. To fully account for potential ecological risk associated with anti-fouling paints, Zn as well as active ingredients should be considered in the regulatory process.     

Enhanced removal of polychlorinated biphenyls from alfalfa rhizosphere soil in a field study: The impact of a rhizobial inoculum

Polychlorinated biphenyls (PCB) are persistent pollutants in soil environments where they continue to present considerable human health risks. Successful strategies to remediate contaminated soils are needed that are effective and of low cost. Bioremediation approaches that include the use of plants and microbial communities to promote degradation of PCB have significant potential but need further assessment under field conditions. The effects of growth of alfalfa (Medicago sativa L.) and inoculation with a symbiotic nitrogen fixing bacterium (Rhizobium meliloti) on the removal of polychlorinated biphenyls (PCB) from rhizosphere soil were evaluated in a field experiment. The initial PCB content of the soil ranged from 414 to 498 µg kg⁻¹. PCB removal for the rhizosphere soil was enhanced in the planted treatments, an average of 36% decrease in PCB levels compared to a 5.4% decrease in the unplanted soil, and further enhanced when plants were inoculated with the symbiotic Rhizobium (an average of 43% decrease) when evaluated at 90 days after planting. Plant biomass production was higher in the inoculated treatment. The total PCB content was increased from 3.30 µg kg⁻¹ to 26.72 µg kg⁻¹ in plant shoots, and from 115.07 µg kg⁻¹ to 142.23 µg kg⁻¹ in roots in the inoculated treatment compared to the planted treatment. Increased colony forming units (cfu) of total heterotrophic bacteria, biphenyl-degrading bacteria and fungi were observed in the rhizosphere of inoculated plants. PCB removal from the rhizosphere soil was not significantly correlated with the direct PCB uptake by the plants in any of the treatments but was significantly correlated with the stimulation of rhizosphere microflora. Changes in the soil microbial community structure in the planted and inoculated treatment were observed by profiling of bacterial ribosomal sequences. Some bacteria, such as Flavobacterium sp., may have contributed to the effective degradation of PCB and deserve further investigation.     

Precipitation of arsenic sulphide from acidic water in a fixed-film bioreactor

Arsenic (As) is a toxic element frequently present in acid mine waters and effluents. Precipitation of trivalent arsenic sulphide in sulphate-reducing conditions at low pH has been studied with the aim of removing this hazardous element in a waste product with high As content. To achieve this, a 400 mL fixed-film column bioreactor was fed continuously with a synthetic solution containing 100 mg L⁻¹ As(V), glycerol and/or hydrogen, at pH values between 2.7 and 5. The highest global As removal rate obtained during these experiments was close to 2.5 mg L⁻¹ h⁻¹. A switch from glycerol to hydrogen when the biofilm was mature induced an abrupt increase in the sulphate-reducing activity, resulting in a dramatic mobilisation of arsenic due to the formation of soluble thioarsenic complexes. A new analytical method, based on ionic chromatography, was used to evaluate the proportion of As present as thioarsenic complexes in the bioreactor. Profiles of pH, total As and sulphate concentrations suggest that As removal efficiency was linked to solubility of orpiment (As₂S₃) depending on pH conditions. Molecular fingerprints revealed fairly homogeneous bacterial colonisation throughout the reactor. The bacterial community was diverse and included fermenting bacteria and Desulfosporosinus-like sulphate-reducing bacteria. arrA genes, involved in dissimilatory reduction of As(V), were found and the retrieved sequences suggested that As(V) was reduced by a Desulfosporosinus-like organism. This study was the first to show that As can be removed by bioprecipitation of orpiment from acidic solution containing up to 100 mg L⁻¹ As(V) in a bioreactor.     

Application of the Nernst-Planck approach to lead ion exchange in Ca-loaded Pelvetia canaliculata

Ca-loaded Pelvetia canaliculata biomass was used to remove Pb²⁺ in aqueous solution from batch and continuous systems. The physicochemical characterization of algae Pelvetia particles by potentiometric titration and FTIR analysis has shown a gel structure with two major binding groups - carboxylic (2.8 mmol g⁻¹) and hydroxyl (0.8 mmol g⁻¹), with an affinity constant distribution for hydrogen ions well described by a Quasi-Gaussian distribution. Equilibrium adsorption (pH 3 and 5) and desorption (eluents: HNO₃ and CaCl₂) experiments were performed, showing that the biosorption mechanism was attributed to ion exchange among calcium, lead and hydrogen ions with stoichiometry 1:1 (Ca:Pb) and 1:2 (Ca:H and Pb:H). The uptake capacity of lead ions decreased with pH, suggesting that there is a competition between H⁺ and Pb²⁺ for the same binding sites. A mass action law for the ternary mixture was able to predict the equilibrium data, with the selectivity constants α_Ca^H = 9 ± 1 and α_Ca^Pb = 44 ± 5, revealing a higher affinity of the biomass towards lead ions. Adsorption (initial solution pH 4.5 and 2.5) and desorption (0.3 M HNO₃) kinetics were performed in batch and continuous systems. A mass transfer model using the Nernst-Planck approximation for the ionic flux of each counter-ion was used for the prediction of the ions profiles in batch systems and packed bed columns. The intraparticle effective diffusion constants were determined as 3.73 × 10⁻⁷ cm² s⁻¹ for H⁺, 7.56 × 10⁻⁸ cm² s⁻¹ for Pb²⁺ and 6.37 × 10⁻⁸ cm² s⁻¹ for Ca²⁺.     

Performance of a passive treatment system for net-acidic coal mine drainage over five years of operation

A full-scale passive treatment system (PTS) was commissioned in 2003 to treat two net-acidic coal mine water discharges in the Durham coalfield, UK. The principal aim of the PTS was to decrease concentrations of iron (< 177 mg L⁻¹) and aluminium (< 85 mg L⁻¹) and to increase pH (> 3.2) and alkalinity (≥ 0 mg L⁻¹ CaCO₃ eq). Secondary objectives were to decrease zinc (< 2.8 mg L⁻¹), manganese (< 20.5 mg L⁻¹) and sulfate (< 2120 mg L⁻¹). Upon treatment, water qualities were improved by 84% in the case of Fe, 87% Al, 83% acidity, 51% Zn, 23% Mn and 29% SO₄²⁻. Alkalinity (74%) and pH (95% as H⁺) were increased. Area adjusted removal rates (Fe = 1.49 ± 0.66 g d⁻¹ m⁻²; acidity = 6.7 ± 4.9 g d⁻¹ m⁻²) were low compared to design criteria, mainly due to load limitation. Disregarding seasonality effects, acidity removal and effluent pH were stable over time. A substantial temporal decrease in calcium and alkalinity generation suggests that limestone is increasingly armoured. Once pH is no longer buffered by the carbonate system, metals could be remobilized, putting treatment efficiency at risk.     

Atmospheric NH3 and NO2 concentration and nitrogen deposition in an agricultural catchment of Eastern China

To assess the atmospheric environmental impacts of anthropogenic reactive nitrogen in the fast-developing Eastern China region, we measured atmospheric concentrations of nitrogen dioxide (NO₂) and ammonia (NH₃) as well as the wet deposition of inorganic nitrogen (NO₃⁻ and NH₄⁺) and dissolved organic nitrogen (DON) levels in a typical agricultural catchment in Jiangsu Province, China, from October 2007 to September 2008_. The annual average gaseous concentrations of NO₂ and NH₃ were 42.2 μg m⁻³ and 4.5 μg m⁻³ (0 °C, 760 mm Hg), respectively, whereas those of NO₃⁻, NH₄⁺, and DON in the rainwater within the study catchment were 1.3, 1.3, and 0.5 mg N L⁻¹, respectively. No clear difference in gaseous NO₂ concentrations and nitrogen concentrations in collected rainwater was found between the crop field and residential sites, but the average NH₃ concentration of 5.4 μg m⁻³ in residential sites was significantly higher than that in field sites (4.1 μg m⁻³). Total depositions were 40 kg N ha⁻¹ yr⁻¹ for crop field sites and 30 kg N ha⁻¹ yr⁻¹ for residential sites, in which dry depositions (NO₂ and NH₃) were 7.6 kg N ha⁻¹ yr⁻¹ for crop field sites and 1.9 kg N ha⁻¹ yr⁻¹ for residential sites. The DON in the rainwater accounted for 16% of the total wet nitrogen deposition. Oxidized N (NO₃⁻ in the precipitation and gaseous NO₂) was the dominant form of nitrogen deposition in the studied region, indicating that reactive forms of nitrogen created from urban areas contribute greatly to N deposition in the rural area evaluated in this study.     

Degradation of the antibiotic oxolinic acid by photocatalysis with TiO2 in suspension

In the work presented here, a photocatalytic system using titanium Degussa P-25 in suspension was used to evaluate the degradation of 20 mg L⁻¹ of antibiotic oxolinic acid (OA). The effects of catalyst load (0.2-1.5 g L⁻¹) and pH (7.5-11) were evaluated and optimized using the surface response methodology and the Pareto diagram. In the range of variables studied, low pH values and 1.0 g L⁻¹ of TiO₂ favoured the efficiency of the process. Under optimal conditions the evolution of the substrate, chemical oxygen demand, dissolved organic carbon, toxicity and antimicrobial activity on Escherichia coli cultures were evaluated. The results indicate that, under optimal conditions, after 30 min, the TiO₂ photocatalytic system is able to eliminate both the substrate and the antimicrobial activity, and to reduce the toxicity of the solution by 60%. However, at the same time, ∼53% of both initial DOC and COD remain in solution. Thus, the photocatalytical system is able to transform the target compound into more oxidized by-products without antimicrobial activity and with a low toxicity. The study of OA by-products using liquid chromatography coupled with mass spectrometry, as well as the evaluation of OA degradation in acetonitrile media as solvent or in the presence of isopropanol and iodide suggest that the reaction is initiated by the photo-Kolbe reaction. Adsorption isotherm experiments in the dark indicated that under pH 7.5, adsorption corresponded to the Langmuir adsorption model, indicating the dependence of the reaction on an initial adsorption step.     

Effects of lanthanum and lanthanum-modified clay on growth, survival and reproduction of Daphnia magna

The novel lanthanum-modified clay water treatment technology (Phoslock^®) seems very promising in remediation of eutrophied waters. Phoslock^® is highly efficient in stripping dissolved phosphorous from the water column and in intercepting phosphorous released from the sediments. The active phosphorous-sorbent in Phoslock^® is the Rare Earth Element lanthanum. A leachate experiment revealed that lanthanum could be released from the clay, but only in minute quantities of 0.13-2.13 μg l⁻¹ for a worst-case Phoslock^® dosage of 250 mg l⁻¹. A life-history experiment with the zooplankton grazer Daphnia magna revealed that lanthanum, up to the 1000 μg l⁻¹ tested, had no toxic effect on the animals, but only in medium without phosphorous. In the presence of phosphorous, rhabdophane (LaPO₄ · nH₂O) formation resulted in significant precipitation of the food algae and consequently affected life-history traits. With increasing amounts of lanthanum, in the presence of phosphate, animals remained smaller, matured later, and reproduced less, resulting in lower population growth rates. Growth rates were not affected at 33 μg La l⁻¹, but were 6% and 7% lower at 100 and 330 μg l⁻¹, respectively, and 20% lower at 1000 μg l⁻¹. A juvenile growth assay with Phoslock^® tested in the range 0-5000 mg l⁻¹, yielded EC₅₀ (NOEC) values of 871 (100) and 1557 (500) mg Phoslock^® l⁻¹ for weight and length based growth rates, respectively. The results of this study show that no major detrimental effects on Daphnia are to be expected from Phoslock^® or its active ingredient lanthanum when applied in eutrophication control.     

Evidences of non-reactive mercury-selenium compounds generated from cultures of Pseudomonas fluorescens

This work was designed to determine chemically inert mercury-selenium (Hg-Se) compounds formed in a culture of Pseudomonas fluorescens exposed to Hg²⁺ and Se^IV (selenite). To isolate these compounds, different digestion methods were studied and sodium dodecyl sulfate (SDS) lysis was selected. The Hg⁰ and non-reactive Hg were determined in two series of cultures containing 0.0-6.00 μg L⁻¹ Se^IV (0.0-76.0 μmol L⁻¹) in combination with low 5.00 μg L⁻¹ (0.025 μmol L⁻¹) or high 100 μg L⁻¹ (0.500 μmol L⁻¹) Hg²⁺. It was found that Hg⁰ formed in the culture decreased with the increase of initial Se^IV, while the non-reactive Hg increased with the Se^IV. In cultures with low initial [Hg²⁺], a median Se^IV (2.0 μg L⁻¹ or 25.3 μmol L⁻¹) resulted in about 70% of the added Hg²⁺ sequestered as non-reactive Hg, and in culture with high initial Hg²⁺, about 40% was sequestered. P. fluorescens was proved to be indispensible for the formation of the non-reactive Hg-Se compounds. The Hg:Se molar ratio in the non-reactive Hg-Se compounds was close to 1, suggesting the existence of mercuric selenide in cells. Mechanisms for the formation of the non-reactive Hg-Se compounds are proposed.     

Sediment reworking rates in deep sediments of the Mediterranean Sea

Different pelagic areas of the Mediterranean Sea have been investigated in order to quantify physical and biological mixing processes in deep sea sediments. Herein, results of eleven sediment cores sampled at different deep areas (> 2000 m) of the Western and Eastern Mediterranean Sea are presented.²¹⁰Pb_xs and ¹³⁷Cs vertical profiles, together with ¹⁴C dating, are used to identify the main processes characterising the different areas and, finally, controlling mixing depths (SML) and bioturbation coefficients (D_b). Radionuclide vertical profiles and inventories indicate that bioturbation processes are the dominant processes responsible for sediment reworking in deep sea environments.Results show significant differences in sediment mixing depths and bioturbation coefficients among areas of the Mediterranean Sea characterised by different trophic regimes. In particular, in the Oran Rise area, where the Almeria-Oran Front induces frequent phytoplankton blooms, we calculate the highest values of sediment mixing layers (13 cm) and bioturbation coefficients (0.187 cm² yr⁻¹), and the highest values of ²¹⁰Pb_xs and ¹³⁷Cs inventories. Intermediate values of SML and D_b (~ 6 cm and ~ 0.040 cm² yr⁻¹, respectively) characterise the mesothrophic Algero-Balearic basin, while in the Southern Tyrrhenian Sea mixing parameters (SML of 3 cm and D_b of 0.011 cm² yr⁻¹) are similar to those calculated for the oligotrophic Eastern Mediterranean (SML of 2 cm and D_b of ~ 0.005 cm² yr⁻¹).     

Multiple site study of recent atmospheric metal (Pb, Zn and Cu) deposition in the NW Iberian Peninsula using peat cores

In order to estimate atmospheric metal deposition in Southern Europe since the beginning of the Industrial Period (~ 1850 AD), concentration profiles of Pb, Zn and Cu were determined in four ²¹⁰Pb-dated peat cores from ombrotrophic bogs in Serra do Xistral (Galicia, NW Iberian Peninsula). Maximum metal concentrations varied by a factor of 1.8 for Pb and Zn (70 to 128 μg g⁻¹ and 128 to 231 μg g⁻¹, respectively) and 3.5 for Cu (11 to 37 μg g⁻¹). The cumulative metal inventories of each core varied by a factor of 3 for all analysed metals (132 to 329 μg cm⁻² for Pb, 198 to 625 μg cm⁻² for Zn and 22 to 69 μg cm⁻² for Cu), suggesting differences in net accumulation rates among peatlands. Although results suggest that mean deposition rates vary within the studied area, the enhanced ²¹⁰Pb accumulation and the interpretation of the inventory ratios (²¹⁰Pb/Pb, Zn/Pb and Cu/Pb) in two bogs indicated that either a record perturbation or post-depositional redistribution effects must be considered. After correction, Pb, Zn and Cu profiles showed increasing concentrations and atmospheric fluxes since the mid-XX^th century to maximum values in the second half of the XX^th century. For Pb, maximum fluxes were observed in 1955-1962 and ranged from 16 to 22 mg m⁻² yr⁻¹ (mean of 18 ± 1 mg m⁻² yr⁻¹), two orders of magnitude higher than in the pre-industrial period. Peaks in Pb fluxes in Serra do Xistral before the period of maximum consumption of leaded petrol in Europe (1970s-1980s) suggest the dominance of local pollutant sources in the area (i.e. coal mining and burning). More recent peaks were observed for Zn and Cu, with fluxes ranging from 32 to 52 mg m⁻² yr⁻¹ in 1989-1996, and from 4 to 9 mg m⁻² yr⁻¹ in 1994-2001, respectively. Our results underline the importance of multi-core studies to assess both the integrity and reliability of peat records, and the degree of homogeneity in bog accumulation. We show the usefulness of using the excess ²¹⁰Pb inventory to distinguish between differential metal deposition, accumulation or anomalous peat records.     

Nitrogen transformations and greenhouse gas emissions from a riparian wetland soil: an undisturbed soil column study

Riparian wetlands bordering intensively managed agricultural fields can act as biological filters that retain and transform agrochemicals such as nitrate and pesticides. Nitrate removal in wetlands has usually been attributed to denitrification processes which in turn imply the production of greenhouse gases (CO₂ and N₂O). Denitrification processes were studied in the Salburua wetland (northern Spain) by using undisturbed soil columns which were subsequently divided into three sections corresponding to A-, Bg- and B2g-soil horizons. Soil horizons were subjected to leaching with a 200 mg NO₃⁻ L^− 1 solution (rate: 90 mL day^− 1) for 125 days at two different temperatures (10 and 20 °C), using a new experimental design for leaching assays which enabled not only to evaluate leachate composition but also to measure gas emissions during the leaching process. Column leachate samples were analyzed for NO₃⁻ concentration, NH₄⁺ concentration, and dissolved organic carbon. Emissions of greenhouse gases (CO₂ and N₂O) were determined in the undisturbed soil columns. The A horizon at 20 °C showed the highest rates of NO₃⁻ removal (1.56 mg N-NO₃⁻ kg⁻¹ DW soil day^− 1) and CO₂ and N₂O production (5.89 mg CO₂ kg⁻¹ DW soil day^− 1 and 55.71 μg N-N₂O kg⁻¹ DW soil day^− 1). For the Salburua wetland riparian soil, we estimated a potential nitrate removal capacity of 1012 kg N-NO₃⁻ ha^− 1 year^− 1, and potential greenhouse gas emissions of 5620 kg CO₂ ha^− 1 year^− 1 and 240 kg N-N₂O ha^− 1 year^− 1.     

Environmental impact of mining activities in the Lousal area (Portugal): chemical and diatom characterization of metal-contaminated stream sediments and surface water of Corona stream

Lousal mine is a typical “abandoned mine” with all sorts of problems as consequence of the cessation of the mining activity and lack of infrastructure maintenance. The mine is closed at present, but the heavy metal enriched tailings remain at the surface in oxidizing conditions. Surface water and stream sediments revealed much higher concentrations than the local geochemical background values, which the “Contaminated Sediment Standing Team” classifies as very toxic. High concentrations of Cu, Pb, Zn, As, Cd and Hg occurred within the stream sediments downstream of the tailings sites (up to: 817 mg kg⁻¹ As, 6.7 mg kg⁻¹ Cd, 1568 mg kg⁻¹ Cu, 1059 mg kg⁻¹ Pb, 82.4 mg kg⁻¹ Sb, 4373 mg kg⁻¹ Zn). The AMD waters showed values of pH ranging from 1.9 to 2.9 and concentrations of 9249 to 20,700 mg L⁻¹ SO₄⁻², 959 to 4830 mg L⁻¹ Fe and 136 to 624 mg L⁻¹ Al. Meanwhile, the acid effluents and mixed stream waters also carried high contents of SO₄^2−, Fe, Al, Cu, Pb, Zn, Cd, and As, generally exceeding the Fresh Water Aquatic Life Acute Criteria. Negative impacts in the diatom communities growing at different sites along a strong metal pollution gradient were shown through Canonical Correspondence Analysis: in the sites influenced by Acid Mine Drainage (AMD), the dominant taxon was Achnanthidium minutissimum. However, Pinnularia acoricola was the dominant species when the environmental conditions were extremely adverse: very low pH and high metal concentrations (sites 2 and 3). Teratological forms of Achnanthidium minutissimum (Kützing) Czarnecki, Brachysira vitrea (Grunow) Ross in Hartley, Fragilaria rumpens (Kützing) G. W. F. Carlson and Nitzschia hantzschiana Rabenhorst were found. A morphometric study of B. vitrea showed that a decrease in size was evident at the most contaminated sites. These results are evidence of metal and acidic pollution.     

Temporal variation of nitro-polycyclic aromatic hydrocarbons in PM10 and PM2.5 collected in Northern Mexico City

With the aim to determine the presence of individual nitro-PAH contained in particles in the atmosphere of Mexico City, a monitoring campaign for particulate matter (PM₁₀ and PM_2.5) was carried out in Northern Mexico City, from April 2006 to February 2007. The PM₁₀ annual median concentration was 65.2 μg m^− 3 associated to 7.6 μg m^− 3 of solvent-extractable organic matter (SEOM) corresponding to 11.4% of the PM₁₀ concentration and 38.6 μg m^− 3 with 5.9 μg m^− 3 SEOM corresponding to 15.2% for PM_2.5. PM concentration and SEOM varied with the season and the particle size. The quantification of nitro-polycyclic aromatic hydrocarbons (nitro-PAH) was developed through the standards addition method under two schemes: reference standard with and without matrix, the former giving the best results. The recovery percentages varied with the extraction method within the 52 to 97% range depending on each nitro-PAH. The determination of the latter was effected with and without sample purification, also termed fractioning, giving similar results. 8 nitro-PAH were quantified, and their sum ranged from 111 to 819 pg m^− 3 for PM₁₀ and from 58 to 383 pg m^− 3 for PM_2.5, depending on the season. The greatest concentration was for 9-Nitroanthracene in PM₁₀ and PM_2.5, detected during the cold-dry season, with a median (10th-90th percentiles) concentration in 235 pg m^− 3 (66-449 pg m^− 3) for PM₁₀ and 73 pg m^− 3 (18-117 pg m^− 3) for PM_2.5. The correlation among mass concentrations of the nitro-PAH and criteria pollutants was statistically significant for some nitro-PAH with PM₁₀, SEOM in PM₁₀, SEOM in PM_2.5, NO_X, NO₂ and CO, suggesting either sources, primary or secondary origin. The measured concentrations of nitro-PAH were higher than those reported in other countries, but lower than those from Chinese cities. Knowledge of nitro-PAH atmospheric concentrations can aid during the surveillance of diseases (cardiovascular and cancer risk) associated with these exposures.     

Selenium concentrations of common weeds and agricultural crops grown in the seleniferous soils of northwestern India

The plants grown in seleniferous soils constitute a major source of toxic selenium levels in the food chain of animals and human beings. Greenhouse and field experiments were conducted to study selenium concentrations of weeds, forages and cereals grown on seleniferous soils located between 31.0417° to 31.2175° N and 76.1363° to 76.4147° E in northwestern India. Eleven winter season (November-April) weed plants were grown in the greenhouse in a soil treated with different levels of selenate-Se. Selenium concentrations of weed plants increased progressively with the levels of selenate-Se in soil. The highest Se concentration was recorded by Silene gallica (246 mg kg^− 1) and the lowest by Avena ludoviciana (47 mg kg^− 1) at 2.5 mg Se kg^− 1 soil. A.ludoviciana and Spergula arvensis proved highly tolerant to the presence of 1.25 and 2.5 mg selenate-Se kg^− 1 soil and the remaining weeds were sensitive to Se. Dry matter yield of Se-sensitive weed plants was 25 to 62% of the yield in the no-Se control at 1.25 mg selenate-Se kg^− 1 and 6 to 40% at 2.5 mg selenate-Se kg^− 1 soil. Other symptoms like change in leaf colour and size, burning of leaf tips and margins, and delayed flowering were also observed due to Se. Dry matter yield of Se-sensitive weed plants expressed as percentage of yield in the no-Se control at both the Se levels was inversely correlated with their Se content (r = − 0.731, p < 0.01, N = 17). Among the weed plants grown in seleniferous soils under field situations, Mentha longifolia accumulated the highest Se (365 mg kg^− 1) and Phalaris minor the lowest (34 mg kg^− 1). Among agricultural crops grown on a naturally contaminated soil in the greenhouse, Se concentrations were the highest for oilseed crops (19-29 mg kg^− 1), followed by legumes (6-13 mg kg^− 1) and cereals (2-18 mg kg^− 1). Helianthus annuus among the oilseed crops, A.ludoviciana among the winter season weeds, M.longifolia among the summer season (May-October) weeds and Cirsium arvense among the perennial weeds can be used for phytoremediation of seleniferous soils as these accumulate the highest amounts of Se.     

Using magnetic seeds to improve the aggregation and precipitation of nanoparticles from backside grinding wastewater

Backside grinding (BG) wastewater treatment typically requires large quantities of chemicals, i.e. polyaluminum chloride (PAC) coagulant and produces considerable amounts of sludge, increasing the loading and cost of subsequent sludge treatment and disposal processes. This study investigated the effects of the addition of magnetic seeds (FeO*Fe₂O₃) of selected particle sizes and of optimized combinations of magnetic seeds and PAC on the aggregation of silica nanoparticles from BG wastewater and on the sedimentation time at various pH values (5-9). The results show that the turbidity of BG wastewater was significantly reduced by the magnetic aggregation treatment. The dosage of PAC combined with 2.49 g L⁻¹ or 1.24 g L⁻¹ of magnetic seeds was reduced by 83% (from 60 to 10 mg L⁻¹) compared to the conventional process of using only PAC as a coagulant. The turbidity of the BG wastewater, initially 1900-2500 NTU, could also be successfully decreased about to 23 NTU by the addition of 3.74 g L⁻¹ magnetite (FeO*Fe₂O₃) only at pH 5 with an applied magnetic field of 1000 G. Different coagulation conditions using magnetic seeds combined with coagulant resulted in different aggregation performances. The treatment performance was more effective by using two-stage dosing, in which magnetic seeds and PAC were added separately, than that with one-stage dosing, where the magnetic seeds and PAC were added simultaneously during rapid mixing. The two-stage dosing allowed for a reduction in the optimum dosage of magnetic seeds from 3.74 g L⁻¹ to 2.49 g L⁻¹ or 1.24 g L⁻¹ without affecting performance when coupled with 0.01 g L⁻¹ of PAC coagulant. The developed method effectively reduced the production of waste sludge.     

Organochlorine pesticides, polychlorinated biphenyls and trace elements in wild European sea bass (Dicentrarchus labrax) off European estuaries

Polychlorinated biphenyls (PCBs) and organochlorine pesticides like dichloro-diphenyl-trichloroethane (DDTs), hexachlorocyclohexanes (HCHs), aldrin, dieldrin and trace elements (Cd, Cu, Se, Pb, Zn and Hg) were analysed in the muscle of European sea bass (Dicentrarchus labrax) sampled in Atlantic coastal regions near several important European river mouths (Gironde, Charente, Loire, Seine and Scheldt). High contamination levels were measured in the muscles of European sea bass sampled in the coastal regions near those river mouths (e.g. Σ ICES PCB = 133-10,478 μg kg^− 1 lw and Hg = 250-2000 μg kg^− 1 dw).The Scheldt and the Seine are still among the most contaminated estuaries in Europe. Each region presented their specific contamination patterns reflecting different sources due to the input of the respective rivers. As fish and fishery products are the main contributors of the total dietary intake of organochlorinated pollutants, regular consumption of European sea bass with the reported contamination levels may represent a significant exposure route for the general human population.