SiO2胶体晶体的自组装结构及其带隙特征

光子晶体是一种具有光子带隙的新型功能材料.利用垂直沉积自组装法制成SiO2胶体晶体,并利用扫描电子显微镜和紫外分光度计对胶体晶体的显微形貌和光学特征进行了研究.结果表明,利用垂直沉积法自组装得到的SiO2胶体晶体具有面心立方结构;在可见光波段,胶体晶体在＜111＞面方向存在光子带隙.     

光子晶体用二氧化硅胶体球的改性制备及其自组装

采用一步法制备了表面接枝甲基丙烯酰氧基三甲氧基硅烷(MPS)的单分散SiO2胶体球,并通过垂直沉积法在40℃、60%相对湿度下组装出有序性较好的密排结构的SiO2光子晶体.傅立叶红外光谱(FT-IR)和X射线光电子能谱(XPS)结果证明SiO2胶体球表面接枝上了MPS;扫描电子显微镜(SEM)结果表明改性后SiO2胶体球平均粒径为284nm,单分散性较高,平均标准偏差＜5%;制备出的光子晶体是面心立方(fcc)紧密堆积结构;吸收光谱表明,所制备的光子晶体在(111)方向具有光子晶体的带隙特性,带隙中心波长为646nm.     

SiO2/CdS光子晶体的制备及其光学性能

用化学浴沉淀法(CBD)在SiO2胶体晶体中生长了CdS半导体材料, 并用UV-VIS-NIR光谱仪和荧光光分度计测试了其光学性能.测试结果表明,在SiO2胶体晶体中随着CdS填充量的增加,光子带隙向长波段方向移动且变宽;当发射出的光与基体材料的光子带隙相匹配时,可控制半导体材料的光致发光,同时,可通过控制SiO2胶体颗粒粒经的大小来调节CdS的光致发光性能.     

单分散SiO2微球的合成及胶体晶体的生长

对传统的"Stober-Fink"合成SiO2微球的工艺进行了改进,运用"籽晶生长法"合成了单分散SiO2微球,该法可以准确地控制微球尺寸,提高微球的球形度.采用垂直沉积法制备了胶体晶体,并对样品的结构和光学性能进行了表征.研究了微球尺寸对垂直沉积SiO2胶体晶体光子带隙的影响,结果表明,通过控制微球粒径,可调节光子晶体的带隙位置.     

Se-SiO2三维光子晶体的制备

报道了一种新的调节二氧化硅光子晶体带隙的方法;通过化学镀向SiO2胶体晶体中填充半导体材料Se,获得了Se-SiO2两种介质复合的三维光子晶体;采用扫描电子显微镜(SEM)、X射线衍射和紫外-可见光谱仪(UV-VIS)等对Se-SiO2三维光子晶体的形貌、结构和光学性能进行了观察测试.研究结果表明,Se以纳米晶粒的形式均匀地包覆在SiO2微球表面,形成了Se壳层,与相同晶格周期的SiO2光子晶体相比,Se-SiO2光子晶体的带隙发生了明显的红移.     

硅槽内自组装二氧化硅光子晶体

采用溶剂蒸发法在硅片上微槽内对不同粒径的SiO2微球进行组装,尝试利用刻有微槽的硅片与平坦衬底间形成的毛细管池限制胶体晶体的生长厚度,获得了具有显著光子带隙特征的光子晶体线形阵列,并在此基础上比较了不同实验条件如微球直径、毛细管池物理限制作用等对微球排列方式及规整度的影响.     

二氧化硅胶体晶体的制备及其光子带隙特性

利用胶体颗粒悬浊液的自组织生长技术制备了两种二氧化硅胶体晶体．透射光谱表明：所制备的胶体晶体的光子带隙位于近红外波段,带隙的位置随胶体晶体中胶粒的尺寸而变化;且放置时间延长,带隙将发生蓝移．     

近红外光学带隙硅三维光子晶体的制备

用溶剂蒸发法将单分散SiO2微球组装成三维有序结构的胶体晶体模板,用低压化学气相沉积法填充高折射率材料硅,酸洗去除SiO2模板,获得了硅反蛋白石三维光子晶体.通过扫描电镜、X射线衍射仪和紫外-可见-近红外光谱仪对硅反蛋白石三维光子晶体的形貌、成分、结构和光学性能进行了表征.研究结果表明:Si在SiO2微球空隙内具有较高的结晶质量,填充致密均匀;通过控制沉积条件,可控制硅的填充率;制备的硅反蛋白三维光子晶体在近红外区(1.4μm左右)具有明显的光学反射峰,表现出光学带隙效应,测试的光学性能与理论计算基本吻合.     

ZnO光子晶体的自组装工艺及带隙特征研究

以Zn（Ac）2和DEG为原料,采用胶体自组装工艺制备了不同胶粒尺寸的ZnO光子晶体,探索了胶体自组装ZnO光子晶体的制备工艺,研究了自组装温度、溶剂、悬浮液浓度、热处理温度等因素对光子晶体排布平整度、周期性和空间紧密度的影响规律,对各种工艺条件下光子晶体的带隙特征进行了研究,试验结果表明,通过自组装工艺条件选择可实现对光子晶体带隙结构的可控性制备。     

单分散SiO2胶体球制备及其胶体晶体组装

运用胶体化学法在乙醇介质中合成SiO2胶体球,将制得的样品在30℃下用双氧水浸泡处理48h.用扫描电子显微镜(SEM)、傅立叶红外光谱(FT-TR)、Zeta电位仪和标准氢氧化钠滴定法对其形貌、结构和表面电学性质进行分析.结果表明样品平均粒径为292nm,平均标准偏差小于5%;经双氧水浸泡处理后,SiO2胶体球表面羟基数目增多,在水溶液中的Zeta电位从-55.72mV提高到-63.26mV,表面电荷密度从0.19μC/cm2提高到0.28μC/cm2.通过垂直沉积法,在40℃和60%相对湿度条件下制备出有序性较好、密排结构的SiO2胶体晶体.在SEM下,观察到这种胶体晶体是面心立方(fcc)密排结构,其(111)晶面平行于基底.透射光谱表明,所制备的胶体晶体在(111)方向具有光子晶体的不完全带隙性质.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from