Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Influence of CO2 and H2O on NOx storage and reduction on a Pt–Ba/γ-Al2O3 catalyst

In this paper, the effect of CO₂ and H₂O on NO_x storage and reduction over a Pt–Ba/γ-Al₂O₃ (1 wt.% Pt and 30 wt.% Ba) catalyst is shown. The experimental results reveal that in the presence of CO₂ and H₂O, NO_x is stored on BaCO₃ sites only. Moreover, H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. Only 16% of the total barium is utilized in NO storage. The rich phase shows 95% selectivity towards N₂ as well as complete regeneration of stored NO. In the presence of CO₂, NO is oxidized into NO₂ and more NO_x is stored as in the presence of H₂O, resulting in 30% barium utilization. Bulk barium sites are inactive in NO_x trapping in the presence of CO₂·NH₃ formation is seen in the rich phase and the selectivity towards N₂ is 83%. Ba(NO₃)₂ is always completely regenerated during the subsequent rich phase. In the absence of CO₂ and H₂O, both surface and bulk barium sites are active in NO_x storage. As lean/rich cycling proceeds, the selectivity towards N₂ in the rich phase decreases from 82% to 47% and the N balance for successive lean/rich cycles shows incomplete regeneration of the catalyst. This incomplete regeneration along with a 40% decrease in the Pt dispersion and BET surface area, explains the observed decrease in NO_x storage.     

Quantification of the in situ DRIFT spectra of Pt/K/γ-A12O3 NOx adsorber catalysts

A method to quantify DRIFT spectral features associated with the in situ adsorption of gases on a NO_x adsorber catalyst, Pt/K/Al₂O₃, is described. To implement this method, the multicomponent catalyst is analysed with DRIFT and chemisorption to determine that under operating conditions the surface comprised a Pt phase, a pure γ-Al₂O₃ phase with associated hydroxyl groups at the surface, and an alkalized-Al₂O₃ phase where the surface –OH groups are replaced by –OK groups. Both DRIFTS and chemisorption experiments show that 93–97% of the potassium exists in this form. The phases have a fractional surface area of 1.1% for the 1.7 nm-sized Pt, 34% for pure Al₂O₃ and 65% for the alkalized-Al₂O₃. NO₂ and CO₂ chemisorption at 250 °C is implemented to determine the saturation uptake value, which is observed with DRIFTS at 250 °C. Pt/Al₂O₃ adsorbs 0.087 μmol CO₂/m²and 2.0 μmol NO₂/m², and Pt/K/Al₂O₃ adsorbs 2.0 μmol CO₂/m²and 6.4 μmol NO₂/m². This method can be implemented to quantitatively monitor the formation of carboxylates and nitrates on Pt/K/Al₂O₃ during both lean and rich periods of the NO_x adsorber catalyst cycle.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Mean field modelling of NOx storage on Pt/BaO/Al2O3

A mean field model, for storage and desorption of NO_x in a Pt/BaO/Al₂O₃ catalyst is developed using data from flow reactor experiments. This relatively complex system is divided into five smaller sub-systems and the model is divided into the following steps: (i) NO oxidation on Pt/Al₂O₃; (ii) NO oxidation on Pt/BaO/Al₂O₃; (iii) NO_x storage on BaO/Al₂O₃; (iv) NO_x storage on Pt/BaO/Al₂O₃ with thermal regeneration and (v) NO_x storage on Pt/BaO/Al₂O₃ with regeneration using C₃H₆. In this paper, we focus on the last sub-system. The kinetic model for NO_x storage on Pt/BaO/Al₂O₃ was constructed with kinetic parameters obtained from the NO oxidation model together with a NO_x storage model on BaO/Al₂O₃. This model was not sufficient to describe the NO_x storage experiments for the Pt/BaO/Al₂O₃, because the NO_x desorption in TPD experiments was larger for Pt/BaO/Al₂O₃, compared to BaO/Al₂O₃. The model was therefore modified by adding a reversible spill-over step. Further, the model was validated with additional experiments, which showed that NO significantly promoted desorption of NO_x from Pt/BaO/Al₂O₃. To this NO_x storage model, additional steps were added to describe the reduction by hydrocarbon in experiments with NO₂ and C₃H₆. The main reactions for continuous reduction of NO_x occurs on Pt by reactions between hydrocarbon species and NO in the model. The model is also able to describe the reduction phase, the storage and NO breakthrough peaks, observed in experiments.     

Lean NOx reduction with CO + H2 mixtures over Pt/Al2O3 and Pd/Al2O3 catalysts

The reduction of NO_x by hydrogen under lean burn conditions over Pt/Al₂O₃ is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO_x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al₂O₃. In this case, although pure H₂ and pure CO are ineffective for NO_x reduction under lean burn conditions, H₂/CO mixtures are very effective. With a realistic (1:3) H₂:CO ratio, typical of actual exhaust gas, Pd/Al₂O₃ is significantly more active than Pt/Al₂O₃, delivering 45% NO_x conversion at 160 °C, compared to >15% for Pt/Al₂O₃ under identical conditions. The nature of the support is also critically important, with Pd/Al₂O₃ being much more active than Pd/SiO₂. Possible mechanisms for the improved performance of Pd/Al₂O₃ in the presence of H₂+CO are discussed.     

A comparison study on non-thermal plasma-assisted catalytic reduction of NO by C3H6 at low temperatures between Ag/USY and Ag/Al2O3 catalysts

A comparison study was carried out on non-thermal plasma (NTP)-assisted selective catalytic reduction (SCR) of NO_x by propene over Ag/USY and Ag/Al₂O₃ catalysts. Ag/USY was almost inactive in thermal SCR while it showed obvious activities in NTP-assisted SCR at 100 °C–200 °C. Although the NO_x conversion over Ag/Al₂O₃ was also enhanced at 300 °C–400 °C by the assistance of NTP, it was ineffective below 250 °C. The intermediates over Ag/USY and Ag/Al₂O₃ were investigated using in situ DRIFTS method. It was found that key intermediates in HC-SCR, such as NCO, CN, oxygenates and some N-containing organic species were enriched after the assistance of NTP. The differences in the behaviors of above intermediates were not found between these two kinds of catalysts. However, some evidences suggested that different properties of the absorbed NO_x species resulted in the distinction of SCR reactions over Ag/USY and Ag/Al₂O₃. TPD profiles of Ag/Al₂O₃ showed that nitrates formed over the catalyst were quite stable at low temperatures, which might occupy the active sites and were unfavorable to SCR reactions. The nitrates over Ag/USY were unstable, among which the unidentate nitrate species is probably contributed to the SCR reactions at low temperatures.     

Kinetic modelling of sulfur deactivation of Pt/BaO/Al2O3 and BaO/Al2O3 NOx storage catalysts

In this work, a kinetic model is constructed to simulate sulfur deactivation of the NO_x storage performance of BaO/Al₂O₃ and Pt/BaO/Al₂O₃ catalysts. The model is based on a previous model for NO_x storage under sulfur-free conditions. In the present model the storage of NO_x is allowed on two storage sites, one for complete NO_x uptake and one for a slower NO_x sorption. The adsorption of SO_x is allowed on both of these NO_x storage sites and on one additional site which represent bulk storage. The present model is built-up of six sub-models: (i) NO_x storage under sulfur-free conditions; (ii) SO₂ storage on NO_x storage sites; (iii) SO₂ oxidation; (iv) SO₃ storage on bulk sites; (v) SO₂ interaction with platinum in the presence of H₂; (vi) oxidation of accumulated sulfur compounds on platinum by NO₂. Data from flow reactor experiments are used in the implementation of the model. The model is tested for simulation of experiments for NO_x storage before exposure to sulfur and after pre-treatments either with SO₂ + O₂ or SO₂ + H₂. The simulations show that the model is able to describe the main features observed experimentally.     

Comparative study of structural properties and NOx storage-reduction behavior of Pt/Ba/CeO2 and Pt/Ba/Al2O3

Differences in the NO_x storage-reduction (NSR) behavior of Pt/Ba/CeO₂ and Pt/Ba/Al₂O₃ have been identified and traced to their different chemical and structural properties. The results show that Pt/Ba/CeO₂ exhibits inferior NO_x storage and, particularly, reduction (regeneration) activity compared to the Al₂O₃ supported catalyst. The incomplete reduction of the stored NO_x-species in Pt/Ba/CeO₂ seems to be caused by a faster and more profound reoxidation of Pt particles during the lean period as evidenced by in situ X-ray absorption spectroscopy. Interestingly, the reduction activity could be significantly improved by a pre-reduction step at mild conditions. Exposure of the Pt/Ba/CeO₂ catalyst to reducing H₂ atmosphere in the temperature range 300–500 °C lead to a moderate increase of Pt particle size which beneficially influenced the regeneration activity. In contrast, pre-reduction at temperatures above 500 °C was unfavorable and resulted in a severe decrease of the regeneration activity, probably due to migration of the partially reduced CeO₂ onto the surface of Pt particles.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

Reactor and in situ FTIR studies of Pt/BaO/Al2O3 and Pd/BaO/Al2O3 NOx storage and reduction (NSR) catalysts

The reduction of NO under cyclic “lean”/“rich” conditions was examined over two model 1 wt.% Pt/20 wt.% BaO/Al₂O₃ and 1 wt.% Pd/20 wt.% BaO/Al₂O₃ NO_x storage reduction (NSR) catalysts. At temperatures between 250 and 350 °C, the Pd/BaO/Al₂O₃ catalyst exhibits higher overall NO_x reduction activity. Limited amounts of N₂O were formed over both catalysts. Identical cyclic studies conducted with non-BaO-containing 1 wt.% Pt/Al₂O₃ and Pd/Al₂O₃ catalysts demonstrate that under these conditions Pd exhibits a higher activity for the oxidation of both propylene and NO. Furthermore, in situ FTIR studies conducted under identical conditions suggest the formation of higher amounts of surface nitrite species on Pd/BaO/Al₂O₃. The IR results indicate that this species is substantially more active towards reaction with propylene. Moreover, its formation and reduction appear to represent the main pathway for the storage and reduction of NO under the conditions examined. Consequently, the higher activity of Pd can be attributed to its higher oxidation activity, leading both to a higher storage capacity (i.e., higher concentration of surface nitrites under “lean” conditions) and a higher reduction activity (i.e., higher concentration of partially oxidized active propylene species under “rich” conditions). The performance of Pt and Pd is nearly identical at temperatures above 375 °C.     

Impact of redox conditions on thermal deactivation of NOx traps for diesel

Performance of NO_x traps after high-temperature treatments in different redox environments was studied. Two types of treatments were considered: aging and pretreatment. Lean and rich agings were examined for a model NO_x trap, Pt–Ba/Al₂O₃. These were done at 950 °C for 3 h, in air and in 1% H₂/N₂, respectively. Lean aging had a severe impact on NO_x trap performance, including HC and CO oxidation, and NH₃ and N₂O formation. Rich aging had minimal impact on performance, compared to fresh/degreened performance. Deactivation from lean aging was essentially irreversible due to Pt sintering, but Pt remained dispersed with the rich aging. Pretreatments were examined for a commercially feasible fully formulated NO_x trap and two model NO_x traps, Pt–Ba/Al₂O₃ and Pt–Ba–Ce/Al₂O₃. Pretreatments were done at 600 °C for 10 min, and used feed gas that simulated diesel exhaust under several conditions. Lean pretreatment severely suppressed NO_x, HC, CO, NH₃ and N₂O activities for the ceria-containing NO_x traps, but had no impact on Pt–Ba/Al₂O₃. Subsequently, a relatively mild rich pretreatment reversed this deactivation, which appears to be due to a form of Pt–ceria interaction, an effect that is well known from early work on three-way catalysts. Practical applications of results of this work are discussed with respect to NO_x traps for light-duty diesel vehicles.     

Insight into the key aspects of the regeneration process in the NOx storage reduction (NSR) reaction probed using fast transient kinetics coupled with isotopically labelled NO over Pt and Rh-containing Ba/Al2O3 catalysts

For the first time, the coupling of fast transient kinetic switching and the use of an isotopically labelled reactant (¹⁵NO) has allowed detailed analysis of the evolution of all the products and reactants involved in the regeneration of a NO_x storage reduction (NSR) material. Using realistic regeneration times (ca. 1 s) for Pt, Rh and Pt/Rh-containing Ba/Al₂O₃ catalysts we have revealed an unexpected double peak in the evolution of nitrogen. The first peak occurred immediately on switching from lean to rich conditions, while the second peak started at the point at which the gases switched from rich to lean. The first evolution of nitrogen occurs as a result of the fast reaction between H₂ and/or CO and NO on reduced Rh and/or Pt sites. The second N₂ peak which occurs upon removal of the rich phase can be explained by reaction of stored ammonia with stored NO_x, gas phase NO_x or O₂. The ammonia can be formed either by hydrolysis of isocyanates or by direct reaction of NO and H₂.

The study highlights the importance of the relative rates of regeneration and storage in determining the overall performance of the catalysts. The performance of the monometallic 1.1%Rh/Ba/Al₂O₃ catalyst at 250 and 350 °C was found to be dependent on the rate of NO_x storage, since the rate of regeneration was sufficient to remove the NO_x stored in the lean phase. In contrast, for the monometallic 1.6%Pt/Ba/Al₂O₃ catalyst at 250 °C, the rate of regeneration was the determining factor with the result that the amount of NO_x stored on the catalyst deteriorated from cycle to cycle until the amount of NO_x stored in the lean phase matched the NO_x reduced in the rich phase. On the basis of the ratio of exposed metal surface atoms to total Ba content, the monometallic 1.6%Pt/Ba/Al₂O₃ catalyst outperformed the Rh-containing catalysts at 250 and 350 °C even when CO was used as a reductant.     

A comparative study of the water-gas shift activity of Pt catalysts supported on single (MOx) and composite (MOx/Al2O3, MOx/TiO2) metal oxide carriers

The water-gas shift (WGS) activity of platinum catalysts dispersed on a variety of single metal oxides as well as on composite MO_x/Al₂O₃ and MO_x/TiO₂ supports (M = Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Y, Zr, La, Ce, Nd, Sm, Eu, Gd, Ho, Er, Tm) has been investigated in the temperature range of 150–500 °C, using a feed composition consisting of 3% CO an 10% H₂O. For Pt catalysts supported on single metal oxides, it has been found that both the apparent activation energy of the reaction and the intrinsic rate depend strongly on the nature of the support. In particular, specific activity of Pt at 250 °C is 1–2 orders of magnitude higher when supported on “reducible” compared to “irreducible” metal oxides. For composite Pt/MO_x/Al₂O₃ and Pt/MO_x/TiO₂ catalysts, it is shown that the presence of MO_x results in a shift of the CO conversion curve toward lower reaction temperatures, compared to that obtained for Pt/Al₂O₃ or Pt/TiO₂, respectively. The specific reaction rate is in most cases higher for composite catalysts and varies in a manner which depends on the nature, loading, and primary crystallite size of dispersed MO_x. Results are explained by considering that reducibility of small oxide particles increases with decreasing crystallite size, thereby resulting in enhanced WGS activity. Therefore, evidence is provided that the metal oxide support is directly involved in the WGS reaction mechanism and determines to a significant extent the catalytic performance of supported noble metal catalysts. Results of catalytic performance tests obtained under realistic feed composition, consisting of 3% CO, 10% H₂O, 20% H₂ and 6% CO₂, showed that certain composite Pt/MO_x/Al₂O₃ and Pt/MO_x/TiO₂ catalysts are promising candidates for the development of active WGS catalysts suitable for fuel cell applications.     

TAP study of NOx storage and reduction on Pt/Al2O3 and Pt/Ba/Al2O3

A systematic mechanistic study of NO storage and reduction over Pt/Al₂O₃ and Pt/BaO/Al₂O₃ is carried out using Temporal Analysis of Products (TAP). NO pulse and NO/H₂ pump-probe experiments at 350 °C on pre-reduced, pre-oxidized, and pre-nitrated catalysts reveal the complex interplay between storage and reduction chemistries and the importance of the Pt/Ba coupling. NO pulsing experiments on both catalysts show that NO decomposes to major product N₂ on clean Pt but the rate declines as oxygen accumulates on the Pt. The storage of NO over Pt/BaO/Al₂O₃ is an order of magnitude higher than on Pt/Al₂O₃ showing participation of Ba in the storage even in the absence of gas phase O₂. Either oxygen spillover or transient NO oxidation to NO₂ is postulated as the first steps for NO storage on Pt/BaO/Al₂O₃. The storage on Pt/Ba/Al₂O₃ commences as soon as Pt–O species are formed. Post-storage H₂ reduction provides evidence that a fraction of NO is not stored in close proximity to Pt and is more difficult to reduce. A closely coupled Pt/Ba interfacial process is corroborated by NO/H₂ pump-probe experiments. NO conversion to N₂ by decomposition is sustained on clean Pt using excess H₂ pump-probe feeds. With excess NO pump-probe feeds NO is converted to N₂ and N₂O via the sequence of barium nitrate and NO decomposition. Pump-probe experiments with pre-oxidized or pre-nitrated catalyst show that N₂ production occurs by the decomposition of NO supplied in a NO pulse or from the decomposition of NOx stored on the Ba. The transient evolution of the two pathways depends on the extent of pre-nitration and the NO/H₂ feed ratio.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

The removal of NOx from a lean exhaust gas using storage and reduction on H3PW12O40·6H2O

NO_x sorption and reduction capacities of 12-tungstophosphoric acid hexahydrate (H₃PW₁₂O₄₀·6H₂O, HPW) were measured under representative alternating conditions of lean and rich exhaust-type gas mixture. Under lean conditions, the sorption of NO_x is large and is equivalent to 37 mg of NO_x/g_HPW. Although a part of these NO_x remains unreduced, HPW is able to reduce some of the NO_x to produce N₂ by a reaction between the sorbed NO₂ and hydrocarbon (HC), but this process is slow. The addition of 1% Pt affects strongly the chemical behaviour occurring during the course of a rich operation. The NO desorption observed at the beginning of the rich phase is strongly accelerated. The direct correlation between NO₂ consumption and CO₂ production shows that the principal pathway is the reaction CO+NO₂→CO₂+NO. In a mixture of reducing gas (CO, HC, H₂), the competition is strongly in favour of CO though in its absence the reaction observed was the hydrogenation of propene to propane.