Ultrasonic assessment of textural changes in vacuum packaged sliced Iberian ham induced by high pressure treatment or cold storage

Ultrasonic measurements were used to characterize the effect of high pressure treatment (HPT) (600 MPa/6 min) or cold storage (6 °C/120 days) on the textural properties of vacuum packaged dry-cured ham. The ultrasonic velocity, textural properties and fat content were determined in the ham packages. The ultrasonic velocity was related to the ham hardness, which depends on the sample composition. HPT induced molecular alterations which resulted in an average increase in the hardness of lean tissue of 0.2 N and one of 0.3 N in that of fatty tissue. These textural changes give rise to a velocity increase (8 m/s for lean and 17 m/s for fatty tissue). The cold storage of the Iberian ham also led to an increase in hardness (average 1.10 N) and ultrasonic velocity (average 70 m/s). Therefore, the non-destructive ultrasonic technique could be a reliable method with which to assess the textural changes induced by HPT or cold storage on packaged dry-cured ham.     

Ultrasonic assessment of fresh cheese composition

Fresh cheese composition was assessed by measuring ultrasonic velocity in cheese and cheese blends at different temperatures. Twenty types of commercial, fresh cheeses with fat contents ranging from 0.2% to 17.6% w.b. were analyzed. Ultrasonic velocity was not only heavily dependent on the composition of the cheese but also on its structure. Based on the different effect temperature has on velocity in water and fat, a semi-empirical model was used to estimate the cheese composition from velocity measurements at six temperatures ranging from 3 to 29 °C. The model provided good results for the assessment of the fat (R² = 0.984/0.996; RMSE = 4.6/1.1 for whole and blended cheese, respectively) and water (R² = 0.964/0.995; RMSE = 6.5/0.7 for whole and blended cheese, respectively) content. The ultrasonic measurements could be carried out during the cooling process that takes place after curdling and used as a quality control tool to detect process anomalies in-line.     

Ultrasonic and sensory characterization of dry-cured ham fat from Iberian pigs with different genetics and feeding backgrounds

The textural and ultrasonic properties of the subcutaneous fat from five batches of dry-cured hams from animals with different genetics (Iberian, Iberian×Duroc) and type of feeding ("montanera", concentrate feeds with different oleic acid content) were studied and related to the sensory traits (oiliness and brightness) of their biceps femoris muscle. The different genetics and feeding backgrounds found in the batches brought about differences in their ultrasonic velocities (average velocity from 4 to 20°C ranged from 1608 to 1650m/s) and textural parameters (maximum force at 8°C ranged from 11 to 21N). On average, batches with lower textural parameters had lower velocities and higher sensory scores. Ultrasonic measurements were used to carry out a discriminant analysis which allowed 78.3% of the samples to be correctly classified in the batches considered. Therefore, ultrasonic and sensory techniques could be useful in the characterization and differentiation of dry-cured hams from Iberian pigs.     

Advances in the ultrasound characterization of dry-cured meat products

In this work, the feasibility of using non-contact ultrasonic techniques (air-coupled and scanning acoustic microscopy, SAM) for characterizing different dry-cured meat products was assessed. Air-coupled ultrasonic measurements were performed on vacuum packaged sliced dry-cured ham, and compared with contact measurements. The average ultrasonic velocity in dry-cured ham was 1846 ± 49 m/s and 1842 ± 42 m/s for air-coupled and contact measurements, respectively. The deviation (1% relative error) between both techniques was related to the influence of the heterogeneous structure and composition of dry-cured ham and the transducer focusing. The SAM was used to characterize dry-cured ham and chorizo samples. B-scan images for dry-cured ham and chorizo showed two dominant reflections from the sample, linked to reflections in the lean and fatty tissues. The results indicate that contact ultrasonic measurements could be replaced by the air-coupled technique, reducing the measuring time and the material handling. On the other hand, SAM technique allows the microscopic characterization of dry-cured meat products.     

Ultrasonic monitoring of lard crystallization during storage

This work addresses the use of ultrasonics as a non-destructive technique with which to monitor lard crystallization during cooling and storage. The ultrasonic velocity was measured during both the isothermal crystallization of lard (at 0, 3, 5, 7, 10 and 20 °C) and during the non-isothermal crystallization. In addition, lard crystallization was also studied through Differential Scanning Calorimetry (DSC) and instrumental texture analysis (penetration tests). The measurement of the ultrasonic velocity allowed the bulk crystallization to be detected. The evolution of the ultrasonic velocity and the textural measurements during isothermal crystallization showed two steep increases, which may be explained by the two fractions of triglycerides found in DSC thermograms. At 7, 10 and 20 °C the second fraction did not crystallize within the first 11 days of storage. A two-step crystallization model based on the Avrami model was used to properly describe (% var > 99.9 and RMSE < 1.99 m s^− 1) the relationship between the ultrasonic velocity and the isothermal crystallization time. In addition, a model was developed to estimate the percentage of solid fat content during isothermal crystallization. Therefore, it may be pointed out that ultrasonic techniques could be useful to monitor the crystallization pattern of complex fats during long periods of storage.     

Trans-free plastic shortenings from coconut stearin and palm stearin blends

Coconut oil was fractionated to get 40% and 60% stearins (CSt1 and CSt2), blended with a hard fraction (PSt) from palm oil (10–90%) and its suitability as a plastic fat was studied. Slip melting point increased with increase in the level of PSt and ranged from 25.9 to 49.6 °C. CSt2 did not contain any solids above 20 °C but increased on incorporating PSt and showed the wider melting range required for plastic fats. Melting profiles of the blends containing 30% and 40% PSt were comparable with that of a commercial bakery shortening. Triglyceride composition showed that the blends contained lower and higher molecular weight triglycerides desirable for plastic fats. FTIR spectra showed a distinct peak at 966 cm⁻¹ characteristic of trans fatty acids in commercial shortening while the peak was absent in blends. This study showed that the blends containing 60–70% CSt with PSt are suitable as trans-free plastic fats.     

Electron spin resonance (ESR) spectroscopy study of dry-cured ham treated with electron-beam

The generation, accumulation and decay of free radicals in muscle and fat fractions from three varieties of Spanish dry-cured ham treated (0–4 kGy) in an electron accelerator have been studied by electron spin resonance (ESR) spectroscopy. In the ESR spectra from fat fractions, a well-resolved triplet signal corresponding to an alkyl radical was found only in treated samples. Linear regression models (P < 0.05) were obtained for ESR signal intensity estimation using the absorbed dose and storage time at 4 °C (from 0 to 28 days). Several ESR signals were observed in the spectra from muscle fractions related to the presence of metalloprotein complexes. However, no significant (P > 0.05) differences were found between ESR spectra from untreated (0 kGy) and treated (0–4 kGy) samples. Results suggest that the analysis of ESR spectrum in fat samples can be used to evaluate the E-beam treatment of dry-cured ham.     

Ultrasonic characterisation of B. femoris from Iberian pigs of different genetics and feeding systems

Ultrasonic velocity was used to characterise the differences in composition and texture of Biceps Femoris muscles from four batches of pigs of different genetics (Iberian and Iberian × Duroc) and feeding systems ("montanera" and concentrate). Significant differences (p<0.05) were found for the ultrasonic velocity in samples with different genetics and feeding systems. These differences were dependent on the temperature of the measurements and were related to the intramuscular fat content (IMF) of the samples and, therefore, to the meat quality. The ultrasonic velocities at 0 and 20 °C were related to the IMF (R=0.77 and 0.65, respectively). A discriminant analysis, including ultrasonic velocity at temperatures from 0 to 20 °C, allowed 87.0% of the samples to be correctly classified in the batches. Therefore, ultrasonics could be useful in the characterisation and differentiation of B. femoris muscles of Iberian pigs with different genetics and from different feeding systems.     

Improvement in melting and baking properties of low-fat Mozzarella cheese

Low-fat cheeses dehydrate too quickly when baked in a forced air convection oven, preventing proper melting on a pizza. To overcome this problem, low-fat Mozzarella cheese was developed in which fat is released onto the cheese surface during baking to prevent excessive dehydration. Low-fat Mozzarella cheese curd was made with target fat contents of 15, 30, 45, and 60 g/kg using direct acidification of the milk to pH 5.9 before renneting. The 4 portions of cheese curd were comminuted and then mixed with sufficient glucono-δ-lactone and melted butter (45, 30, 15, or 0 g/kg, respectively), then pressed into blocks to produce low-fat Mozzarella cheese with about 6% fat and pH 5.2. The cheeses were analyzed after 15, 30, 60, and 120 d of storage at 5°C for melting characteristics, texture, free oil content, dehydration performance, and stretch when baked on a pizza at 250°C for 6 min in a convection oven. Cheeses made with added butter had higher stretchability compared with the control cheese. Melting characteristics also improved in contrast to the control cheese, which remained in the form of shreds during baking and lacked proper melting. The cheeses made with added butter had higher free oil content, which correlated (R² ≥ 0.92) to the amount of butterfat added, and less hardness and gumminess compared with the control low fat cheese.     

Optimisation of lipase-catalysed interesterification reaction for modulating rheological and heat transfer properties of frying oil

The present work reports the optimisation of enzyme interesterification reaction of rice bran oil (RBO) and refined, bleached, deodorized, palm olein (RBDPO) blend using immobilized 1,3-specific lipase, to improve the kinematic viscosity and heat transfer coefficient of oil, important for characterising heat transfer during the frying process. Four variables, namely RBO (20–80%) in RBO–RBDPO blend, reaction temperature (25–65 °C), enzyme concentration (1–13%, w/w) and reaction time (1–13 h) were selected and optimised using response surface methodology (RSM) coupled with central composite rotatable design (CCRD). The optimisation results predicted that optimum reaction conditions for preparing enzyme interesterified oil, having minimum kinematic viscosity (2.63 × 10⁻⁶ m² s⁻¹) and maximum heat transfer coefficient (262.0 Wm⁻² °C⁻¹) were at 62% RBO, temperature 65 °C, enzyme concentration 10% (w/w) and time 6.4 h. The predicted values were validated experimentally and corroborated with DSC melting profile and triacylglycerol molecular species data. This investigation could help snack food industries to develop suitable oils for frying operations.     

Migration of α-tocopherol and resveratrol from poly(L-lactic acid)/starch blends films into ethanol

Poly(L-lactic acid) (PLLA)/starch blends with various concentrations of two natural antioxidants, α-tocopherol (α-TOC) and resveratrol, were fabricated by a melt blending and compression molding processes. The effects of the two antioxidants on the optical (color), thermal and mechanical properties of PLLA/starch blends with antioxidants were assessed. PLLA/starch blend films with α-TOC and resveratrol showed a yellowish color influenced by the combined effect of white starch and the brown color of the antioxidants. The glass transition and melting temperatures were significantly reduced with the addition of antioxidants while enhanced thermal stability was observed, which could be a benefit and important for processing and production. The enhanced mechanical properties could be attributed to not only a compatibilization effect based on the chemical linkage between PLLA and starch chains, but also restriction of the chain mobility by antioxidants. The release of resveratrol from PLLA and PLLA/starch blend films into ethanol followed Fickian behavior. The D values of α-TOC were in the range of 0.47–3.95 × 10⁻¹¹ cm² s⁻¹ for PLLA films and 0.70–6.83 × 10⁻¹¹ cm² s⁻¹ for PLLA/starch blend films at 13 °C, 5.67–13.0 × 10⁻¹¹ cm² s⁻¹ for PLLA films and 4.10–24.2 × 10⁻¹¹ cm² s⁻¹ for PLLA/starch blend films at 23 °C, and 89.0–118.0 × 10⁻¹¹ cm² s⁻¹ for PLLA films and 123–282 × 10⁻¹¹ cm² s⁻¹ for PLLA/starch blend films at 43 °C. The D values of resveratrol were in the range of 0.073–0.54 × 10⁻¹⁰ cm² s⁻¹ for PLLA films and 1.42–6.93 × 10⁻¹⁰ cm² s⁻¹ for PLLA/starch blend films at 13 °C, 0.90–3.44 × 10⁻¹⁰ cm² s⁻¹ for PLLA films and 4.16–22.3 × 10⁻¹⁰ cm² s⁻¹ for PLLA/starch blend films at 23 °C, and 24.8–74.1 × 10⁻¹⁰ cm² s⁻¹ for PLLA films and 40.1–309 × 10⁻¹⁰ cm² s⁻¹ for PLLA/starch blend films at 43 °C.     

The Influence of Debaryomyces hansenii, Candida deformans and Candida zeylanoides on the aroma formation of dry-cured “lacón”

The volatile profile of dry-cured “lacón” that has been inoculated with three different yeasts were determined and compared with a non-inoculated dry-cured “lacón”. Yeasts (Debaryomyces hansenii, Candida deformans and Candida zeylanoides) that were used as starter cultures in the present study were selected among yeasts that were isolated from native dry-cured “lacón” at different stages of ripening process. These starters were spread on dry-cured “lacón” surface in order to test their capacity to contribute on the generation of volatile compounds. A total of forty two volatile compounds were detected by dynamic headspace sampling followed by gas chromatography–mass spectrometry analysis. Significant differences (P < 0.001) on the volatile profiles of different batches were found in comparison with non-inoculated samples, showing the highest total area values for the inoculated ones. Esters were the most abundant chemical family in all batches studied except for C. zeylanoides batch, which showed greater amount of hydrocarbons than esters. The second more abundant family was hydrocarbons for control and C. deformans batches (147.6 and 445.24 × 10⁶ area units, respectively), alcohols for D. hansenii (363.77 × 10⁶ area units) and esters for C. zeylanoides (248.33 × 10⁶ area units). However, the aldehyde compound group in control batch samples was found to be significantly higher than in the inoculated ones (P < 0.001). Among inoculated batches, D. hansenii batch showed the lowest hexanal content (14.42 × 10⁶ area units) in comparison with non-inoculated batch (105.99 × 10⁶ area units). Among all batches studied, D. hansenii batch presented the highest area values for esters, alcohols, linear hydrocarbons, ketones, acids and furans; control batch for aldehydes and C. zeylanoides batch for branched hydrocarbons. Therefore, the study showed that every yeast strain produced a specific volatile profile which was also different from that of the control dry-cured “lacón”.     

Thermal characteristics,chemical composition and polyphenol contents of date-pits powder

Polyphenol contents in date-pits varied from 21–62 mg gallic acid equivalents (GAE)/g date-pits when acetone–water, ethanol–water, methanol–water and water alone were used as solvents for extraction at temperatures 22, 45, and 60 °C. The BET and GAB monolayer values of date-pits were estimated as 4.3 and 4.1 g/100 g dry-solids. The DSC thermogram of freeze-dried date-pits showed an endothermic peak due to the melting of oil, and a second endothermic peak for solids-melting (i.e. non-fat). The first shift indicated the glass transition (i.e. T_g) while the second exothermic shift after solids-melting indicated the interactions of the components in melted solids. The melting peak temperature was decreased due to the plasticization of solids with water and the melting enthalpy was increased with the increasing water content due to the formation of more order in the amorphous, semi-crystallites and crystallites parts. The Flory–Huggins modelling of peak temperature estimated the water–solids interaction parameter as 0.0068. The melting peak temperature increased exponentially with increasing heating rate and the data was fitted with Mehl–Johnson–Avrami and Kissinger models. Annealing close to the onset of melting indicated that melting peak temperature increased exponentially with increasing annealing time, while melting enthalpy decreased with the increasing annealing time.     

Reduction of NaCl content in restructured dry-cured hams: Post-resting temperature and drying level effects on physicochemical and sensory parameters

The effects of post-resting temperature (5 °C, 15 °C and 25 °C) and drying level (low and high, corresponding to final water contents (w/w) of 57% and 50%, respectively) were evaluated in restructured dry-cured hams. The reduction of NaCl content, with and without the addition of K-lactate as NaCl substitute was also evaluated. Physicochemical and instrumental colour and texture (Stress Relaxation test) parameters and sensory attributes were measured. The main effects of reducing the NaCl addition from 30 g/kg to 15 g/kg in restructured dry-cured hams were the reduction of saltiness and the increase of a_w, proteolysis and softness. The addition of K-lactate (19.7 g/kg) contributed to reduce these effects. Hams from high drying level had a longer processing time and a higher proteolysis index, but lower water content and harder texture. The increase of post-resting temperature to above 5 °C reduced the processing time and the metallic flavour, but at 25 °C restructured hams were spoiled. Therefore, the problems due to the reduction of NaCl to 15 g/kg in restructured dry-cured hams can be reduced by adding K-lactate and drying at 15 °C (after 3.5 months of resting at 5 °C) until a final weight loss of around 45% is reached.     

Near infrared reflectance spectroscopy predicts the content of polyunsaturated fatty acids and biohydrogenation products in the subcutaneous fat of beef cows fed flaxseed

This study examined the ability of near infrared reflectance spectroscopy (NIRS) to estimate the concentration of polyunsaturated fatty acids and their biohydrogenation products in the subcutaneous fat of beef cows fed flaxseed. Subcutaneous fat samples at the 12th rib of 62 cows were stored at − 80 °C, thawed, scanned over a NIR spectral range from 400 to 2498 nm at 31 °C and 2 °C, and subsequently analysed for fatty acid composition. Best NIRS calibrations were with samples at 31 °C, showing high predictability for most of the n−3 (R²: 0.81-0.86; RMSECV: 0.11-1.56 mg g^− 1 fat) and linolenic acid biohydrogenation products such as conjugated linolenic acids, conjugated linoleic acids (CLA), non-CLA dienes and trans-monounsaturated fatty acids with R² (RMSECV_, mg g^− 1 fat) of 0.85-0.85 (0.16-0.37), 0.84-0.90 (0.21-2.58), 0.90 (5.49) and 0.84-0.90 (4.24-8.83), respectively. NIRS could discriminate 100% of subcutaneous fat samples from beef cows fed diets with and without flaxseed.     

At line prediction of PUFA and biohydrogenation intermediates in perirenal and subcutaneous fat from cattle fed sunflower or flaxseed by near infrared spectroscopy

NIRS potential to estimate the proportion of PUFA and their biohydrogenation products in adipose tissues from cattle fed sunflower or flaxseed was tested. Immediately after skinning, perirenal and subcutaneous fat samples from 63 steers were collected, scanned intact at 37 °C and 33 °C, respectively, over a NIR spectral range from 400 to 2498 nm using benchtop equipment and then analyzed for fatty acid composition. NIRS calibrations in perirenal fat showed high predictability for total and major omega − 6 and omega − 3, conjugated linolenic acids, t,t-conjugated linoleic acids (CLA), non-CLA dienes and trans-monounsaturated fatty acids, with R² (RMSECV, %) of 0.88–0.89 (0.16–0.20), 0.89–0.91 (0.07–0.08), 0.86–0.89 (0.01–0.09), 0.82 (0.07), 0.89 (0.46) and 0.86–0.88 (0.87–1.29), respectively. NIRS predictions in subcutaneous fat were less reliable, probably due to lower fatty acid variability. The results show NIRS to be a useful technique for the early, fast and relatively inexpensive estimation of proportions of fatty acids with potential human health effects in cattle perirenal fat.     

Segregative interactions and competitive binding of Ca in gelling mixtures of whey protein isolate with Naκ-carrageenan

Gelling mixtures of Na⁺κ-carrageenan with whey protein isolate (WPI) at pH 7.0 have been studied rheologically and by differential scanning calorimetry (DSC), with comparative measurements for the individual constituents of the mixtures. The concentration of WPI was held fixed at 10.0 wt% and carrageenan concentration was varied in the range 0.05–3.0 wt%. Ca²⁺ cations, which have been shown previously to be particularly effective in inducing gelation of κ-carrageenan, were introduced as CaCl₂. The concentration of CaCl₂ used in most of the experiments was 8 mM, but other concentrations were also studied. Mixtures were prepared in the solution state at 45 °C, and showed no evidence of either phase separation or complex formation. Rheological changes were monitored by low-amplitude oscillatory measurements of storage modulus, G′, during (i) cooling (1 °C/min) and holding at 5 °C, to induce gelation of the carrageenan in the presence of non-gelled WPI; (ii) heating and holding at 80 °C to dissociate the carrageenan network and induce gelation of WPI; (iii) cooling and holding again at 5 °C, to give composite networks with both components gelled; and (iv) re-heating to 80 °C to dissociate the carrageenan network. Gel structure was characterised further by creep–recovery measurements at the end of each holding period, and by torsion measurements at 5 °C, before and after thermal gelation of WPI.     

Determination of the degradation kinetics of anthocyanins in a model juice system using isothermal and non-isothermal methods

The effect of temperature on the degradation of blackcurrant anthocyanins in a model juice system was determined over a temperature range of 4–140 °C. The thermal degradation of anthocyanins followed pseudo first-order kinetics. From 4–100 °C an isothermal method was used to determine the kinetic parameters. In order to mimic the temperature profile in retort systems, a non-isothermal method was applied to determine the kinetic parameters in the model juice over the temperature range 110–140 °C. The results from both isothermal and non-isothermal methods fit well together, indicating that the non-isothermal procedure is a reliable mathematical method to determine the kinetics of anthocyanin degradation. The reaction rate constant (k) increased from 0.16 (±0.01) × 10⁻³ to 9.954 (±0.004) h⁻¹ at 4 and 140 °C, respectively. The temperature dependence of the rate of anthocyanin degradation was modelled by an extension of the Arrhenius equation, which showed a linear increase in the activation energy with temperature.     

Electrical conductivity changes of minced beef–fat blends during ohmic cooking

Minced beef–fat blends having different fat level (2%, 9% and 15%) and full meat-fat samples were ohmically cooked by different voltage gradients (20, 30 and 40 V/cm). Main factors affecting the electrical conductivity were the temperature and the composition of the blends. Although the effect of initial fat content on electrical conductivity was statistically significant, voltage gradient did not affect the electrical conductivity changes during cooking treatment (p > 0.05). The electrical conductivity of the samples increased with increasing temperature up to the critical initial cooking temperature (60–70 °C) depending on the fat level, and then decreased due to structural changes and the increase in the bound water during cooking. The results of the nonlinear mathematical model including the effects of initial fat level and the temperature on the electrical conductivity changes had good agreement (r = 0.952; SEM = 0.009) with the experimental data. The determination of electrical conductivity changes being affected by process variables is crucial to characterize the ohmic cooking of meat products and design of ohmic systems.