Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO_x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Investigation on combustion and emission characteristics of hydrogen-enriched dual-fuel engine operated under waste frying oil biodiesel

Using nonedible waste frying oil (WFO) as biodiesel and hydrogen in the mix composition may partly replace significant quantities of diesel fuel and help reduce fossil fuel reliance. The combination of diesel fuel, waste-fired biodiesel, and hydrogen gas can improve the performance, combustion, and emissions of single-fuel and dual-fuel diesel engines. This may lead to a novel alternative fuel mix pattern and modification for diesel engines, which is the research gap. Although there has been some research on waste-fired biodiesel and hydrogen gas-powered dual-fuel engines with the goal of partly replacing fossil fuels to a larger degree, there has been very little progress in this area. As a result, the current research effort focuses on using diesel fuel (100%, 30%, and 60%), waste-fired biodiesel (at 100%, 70%, and 40%), and hydrogen gas as fuel sources (5 and 10 liters per minute [LPM]). According to the current experiment, it was perceived in both dual-fuel and single-fuel modes. Under duel-fuel mode, the engine results for WFOB70D30 + H10 fuel blend had higher 4.2% (brake thermal efficiency [BTE]), 19.72% (oxides of nitrogen [NO_x]), and 9.09% (ignition delay [ID]) with a minimal range of (in-cylinder pressure, MFB, volumetric efficiency and heat release rate [HRR]) and a dropped rate of 4.34% (brake-specific energy consumption [BSEC]), 33.33% (carbon monoxide [CO]), 39.28% (hydrocarbons [HC]), 9.43% (smoke), and 6.97% (combustion duration [CD]) related to diesel fuel at peak load. However, single-fuel powered diesel engines provide minimal performance for the WFOB40D60 fuel blend with (11.32% lower BTE and 2.04% higher BSEC) and minimal rate of combustion (lower cylinder pressure, 2.12% minimal CD, 14.72% higher ID, minimal HRR combustion, volumetric efficiency, and MFB). Emitted fewer emissions (9.09% less CO, 4.87% less HC, 0.92% higher NO_x, and 1.69% more smoke) than diesel fuel at peak load. Therefore, it was concluded that adding 10 LPM of hydrogen gas to the biodiesel under a dual-fuel condition leads to better combustion, better performance, and less pollution than the single-fuel mode of operation.     

Determination of ecological efficiency in internal combustion engines: The use of biodiesel

This paper evaluates and quantifies the environmental impact from the use of some renewable fuels and fossils fuels in internal combustion engines. The following fuels are evaluated: gasoline blended with anhydrous ethyl alcohol (anhydrous ethanol), conventional diesel fuel, biodiesel in pure form and blended with diesel fuel, and natural gas. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. The ecological efficiency concept depends on the environmental impact caused by CO₂, SO₂, NO_x and particulate material (PM) emissions. The exhaust gases from internal combustion engines, in the case of the gasoline (blended with alcohol), biodiesel and biodiesel blended with conventional diesel, are the less polluting; on the other hand, the most polluting are those related to conventional diesel. They can cause serious problems to the environment because of their dangerous components for the human, animal and vegetable life. The resultant pollution of each one of the mentioned fuels are analyzed, considering separately CO₂, SO₂, NO_x and particulate material (PM) emissions. As conclusion, it is possible to calculate an environmental factor that represents, qualitatively and quantitative, the emissions in internal combustion engines that are mostly used in urban transport. Biodiesel in pure form (B100) and blended with conventional diesel as fuel for engines pollute less than conventional diesel fuel. The ecological efficiency for pure biodiesel (B100) is 86.75%; for biodiesel blended with conventional diesel fuel (B20, 20% biodiesel and 80% diesel), it is 78.79%. Finally, the ecological efficiency for conventional diesel, when used in engines, is 77.34%; for gasoline, it is 82.52%, and for natural gas, it is 91.95%. All these figures considered a thermal efficiency of 30% for the internal combustion engine.     

Biodiesel fuel in diesel micro-turbine engines: Modelling and experimental evaluation

Many performance and emission tests have been carried out in reciprocating diesel engines that use biodiesel fuel over the past years and very few in gas turbine engines. This work aims at assessing the thermal performance and emissions at full and partial loads of a 30 kW diesel micro-turbine engine fed with diesel, biodiesel and their blends as fuel. A cycle simulation was performed using the Gate Cycle GE Enter software to evaluate the thermal performance of the 30 kW micro-turbine engine. Performance and emission tests were carried out on a 30 kW diesel micro-turbine engine installed in the NEST laboratories of the Federal University of Itajubá, and the performance results were compared with those of the simulation. There was a good agreement between the simulations and the experimental results from the full load down to about 50% of the load for diesel, biodiesel and their blends. The biodiesel and its blends used as fuel in micro-turbines led to no significant changes in the engine performance and behaviour compared to diesel fuel. The exhaust emissions were evaluated for pure biodiesel and its blends and conventional diesel. The results revealed that the use of biodiesel resulted in a slightly higher CO, lower NO_x and no SO₂ emissions.     

The influence of hydrogen-enriched gas on the performance of lean NOx trap catalyst for a light-duty diesel engine

Modern diesel engines have improved engine fuel economy and significantly reduced nitrogen oxides (NO_x) and particulate matter (PM) emissions achieved by advances in both combustion and exhaust aftertreatment technologies. Recently, it has been shown that the vehicle emissions can be further improved by several catalytic systems including fuel reformers and aftertreatment systems, such as the Lean NO_x Trap (LNT). This NO_x removal system, called LNT, absorbs NO_x under lean exhaust gas conditions and releases NO_x under rich conditions. This technology can provide high NO_x conversion efficiency, but the right amount of reducing agent should be supplied into the catalytic converter under appropriate conditions.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Evolution,challenges and path forward for low temperature combustion engines

Universal concerns about degradation in ambient environment, stringent emission legislations, depletion of petroleum reserves, security of fuel supply and global warming have motivated research and development of engines operating on alternative combustion concepts, which also have capability of using renewable as well as conventional fuels. Low temperature combustion (LTC) is an advanced combustion concept for internal combustion (IC) engines, which has attracted global attention in recent years. LTC concept is different from the conventional spark ignition (SI) combustion as well as compression ignition (CI) diffusion combustion concepts. LTC technology offers prominent benefits in terms of simultaneous reduction of both oxides of nitrogen (NO_x) and particulate matter (PM), in addition to reduction in specific fuel consumption (SFC). However, controlling ignition timing and combustion rate are primary challenges to be tackled before LTC technology can be implemented in automotive engines commercially. This review covers fundamental aspects of development of LTC engines and its evolution, historical background and origin of LTC concept, encompassing LTC principle, its advantages, challenges and prospects. Detailed insights into preparation of homogeneous charge by external and internal measures for mineral diesel and gasoline like fuels are covered. Fuel requirements and fuel induction system design aspect for LTC engines are also discussed. Combustion characteristics of LTC engines including combustion chemistry, heat release rate (HRR), combustion duration, knock characteristics, high load limit, fuel conversion efficiencies and combustion instability are summarized. Emission characteristics are reviewed along with insights into PM and NO_x emissions from LTC engines. Finally, different strategies for controlling combustion rate and combustion timings for gasoline and mineral diesel like fuels are discussed, showing the way forward for this technology in future towards its commercialization.     

Potential and challenges for large-scale application of biodiesel in automotive sector

Biodiesel is receiving serious attention globally as a potential alternative fuel for replacing mineral diesel, partially or fully. In this review paper, most prominent methods of biodiesel production commercially, life-cycle analysis and economic issues related to biodiesel, engine performance, combustion and emission characteristics including particulate, engine compatibility issues and effect of biodiesel usage on engine component wear and lubricating oil are comprehensively discussed. Majority of biodiesel produced globally is via base-catalyzed transesterification process since this is a low temperature and pressure process, having high conversion rates without intermediate steps, and it uses inexpensive materials of construction for the plant. Catalyst types (alkaline, acidic or enzymatic), catalyst concentration, molar ratio of alcohol/oil, reaction temperature, moisture content of reactants, and free fatty acid (FFA) content of oil are the main factors affecting biodiesel (ester) yield from the transesterification process. Substantial reduction in particulate matter (PM), total hydrocarbons (THC) and carbon monoxide (CO) emissions in comparison to mineral diesel, and increased brake specific fuel consumption (BSFC) and oxides of nitrogen (NO_X) emissions are reported by most researchers using unmodified compression ignition (CI) engines. This review covers several aspects, which are not covered by previous review articles, such as effect of biodiesel on unregulated emissions, effect of biodiesel on carbon deposits, wear of key engine components, and lubricating oil in long-term endurance studies. It emerges from literature review that even minor blends of biodiesel help control emissions and ease pressure on scarce petroleum resources without sacrificing engine power output, engine performance and fuel economy. This review underscores that future studies should focus on optimization of fuel injection equipment and hardware modifications to develop dedicated biodiesel engines, improve low temperature performance of biodiesel fuelled engines, develop new biodiesel compatible lubricating oil formulations and special materials for engine components before implementing large-scale substitution of mineral diesel by biodiesel globally.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Analysis of nitrogen oxide emissions from modern vehicles using hydrogen or other natural and synthetic fuels in combustion chamber

The paper presents a calculated analysis of the equilibrium emission of nitrogen oxides on the exhaust of carburetor and diesel internal combustion engines. The temperature of fuel oxidation is assumed to be 1,400 °C while the pressure for carburetor and diesel engines is assumed to be 60 atm and 80 atm respectively. The studies have been carried out for natural and synthetic fuels such as hydrogen, ethanol, methanol, petroleum, diesel fuel and methane at the excess air coefficient corresponding to the fuel oxidation temperature of 1,400 °C. In the paper, the method for calculating the equilibrium composition based on the equilibrium constant and mass conservation equations has been applied. It is shown that with an increase in pressure from 1 atm to 60 atm for carburetor engines and up to 80 atm for diesel engines, the reaction of nitrogen dioxide formation may shift towards an increase in NO₂. The formation of NO may be not affected by the increase in pressure by virtue of the fact that the reaction proceeds without changes in the amount. It has been determined that NO is the major atmospheric pollutant. However, it would be advisable to use more extensively the fuels characterized by the lowest output of nitrogen dioxide (methane and methanol), since nitrogen dioxide (NO₂) related to the 2nd hazard class is appeared to be the most dangerous to humans. It has been revealed that the reduction in oxidation temperature using hydrogen as a fuel for electrochemical current generators may allow reducing nitrogen oxide emissions by more than an order of magnitude as compared to the best results for ICE.     

Biodiesel from cotton seed oil and its effect on engine performance and exhaust emissions

The use of biodiesel is rapidly expanding around the world, making it imperative to fully understand the impacts of biodiesel on the diesel engine combustion process and pollutant formation. Biodiesel is known as the mono-alkyl-esters of long chain fatty acids derived from renewable feedstocks, such as, vegetable oils or animal fats, for use in compression ignition engines. Different parameters for the optimization of biodiesel production were investigated in the first phase of this study, while in the next phase of the study performance test of a diesel engine with neat diesel fuel and biodiesel mixtures were carried out. Biodiesel was made by the well known transesterification process. Cottonseed oil (CSO) was selected for biodiesel production. Cottonseed is non-edible oil, thus food versus fuel conflict will not arise if this is used for biodiesel production. The transesterification results showed that with the variation of catalyst, methanol or ethanol, variation of biodiesel production was realized. However, the optimum conditions for biodiesel production are suggested in this paper. A maximum of 77% biodiesel was produced with 20% methanol in presence of 0.5% sodium hydroxide. The engine experimental results showed that exhaust emissions including carbon monoxide (CO) particulate matter (PM) and smoke emissions were reduced for all biodiesel mixtures. However, a slight increase in oxides of nitrogen (NO_x) emission was experienced for biodiesel mixtures.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Investigation of a hydrogen-assisted combustion system for a light-duty diesel vehicle

Two sets of experiments were conducted to investigate the effects of adding gaseous hydrogen to the intake of compression–ignition (CI) engines fueled with 20% bio-derived/80% petroleum-derived diesel fuel (B20). A 1.3 L, 53 kW CI engine coupled to an eddy-current engine dynamometer was tested first. Data were collected on engine operating parameters, fuel consumption, concentration of total oxides of nitrogen (NO_x) in the exhaust, and exhaust temperature. Eight steady-state operating points were tested with hydrogen flow rates equivalent to 0%, 5%, and 10% of the total fuel energy. In a second set of experiments, the stock gasoline engine of a 2005 Chevrolet Equinox was replaced with a 1.3 L, 66 kW CI engine, and urban drive cycles were run on a chassis dynamometer. The drive cycles were repeated with 0%, 5% and 10% of the fuel energy coming from the fumigated hydrogen. In both experiments, the addition of hydrogen did not result in discernable differences in engine efficiency. In the vehicle testing, there were no noticeable differences in drivability. There were modest reductions in NO_x emissions and increases in exhaust temperature with hydrogen addition. This investigation demonstrates that fumigating relatively small amounts of hydrogen into the intake of a modern diesel engine results in only modest changes in combustion efficiency and emissions with no detrimental effects on vehicle performance or drivability. This strategy can be used to partially offset the use of petroleum-based fuels in light-duty transportation vehicles.     

Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Influence of fuel properties and composition on NOx emissions from biodiesel powered diesel engines: A review

Biodiesel has proved to be an environment friendly alternative fuel for diesel engine because it can alleviate regulated and unregulated exhaust emissions. However, most researchers have observed a significant increase in NO_x emissions with biodiesel when compared to petrodiesel. The exact cause of this increase is still unclear; however, researchers believe that the fuel properties have been shown to effect the emissions of NO_x. The present work reviews the effect of fuel properties and composition on NO_x emissions from biodiesel fuelled engines. The paper is organised in three sections. The first section deals with the NO_x formation mechanisms. In the following section, the reasons for increased NO_x emissions of biodiesel fuel are discussed. After this, the influence of composition and fuel properties on NO_x emissions from biodiesel fuelled engines has been reviewed. Finally, some general conclusions concerning this problem are summarised and further researches are pointed out.     

Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters

The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NO_x. Overall fish biodiesel showed good combustion properties and environmental benefits.     

Study of antioxidant effect on oxidation stability and emissions in a methyl ester of neem oil fuelled DI diesel engine

Biodiesel as an alternative diesel fuel prepared from vegetable oils or animal fats has attracted more and more attention because of its renewable and environmental-friendly nature. But biodiesel undergoes oxidation and degenerate more quickly than mineral diesel. Further several studies report NO_x emissions increases for biodiesel fuel compared with conventional diesel fuel. In this paper, the experimental investigation of the effect of antioxidant additive (Butylated hydroxytoluene) on oxidation stability and NO_x emissions in a methyl ester of neem oil fuelled direct injection diesel engine has been reported. The antioxidant additive is mixed in various proportions (100–400 ppm) with methyl ester of neem oil. The oxidation stability was tested in Rancimat apparatus and emissions, performance in a computerized 4-stroke water-cooled single cylinder diesel engine of 3.5 kW rated power. Results show that the antioxidant additive is effective in increasing the oxidation stability and in controlling the NO_x emissions of methyl ester of neem oil fuelled diesel engines.     

A comparative study of combustion performance and emission of biodiesel blends and diesel in an experimental boiler

Recently, biodiesel has become more attractive since it is made from renewable resources and also for the fact that the resources of fossil fuels are diminishing day by day. This study compares combustion of B5, B10, B20, B50, B80 and B100 with petroleum diesel over wide input air flows at two energy levels in an experimental boiler. The comparison is made in terms of combustion efficiency and flue gas emissions (CO, CO₂, NO_X, and SO₂) and influence of air flow at two energy levels 219 kJ/h and 249 kJ/h is studied. The findings show that at higher level energy diesel efficiency was a little higher than that of biodiesel, but at lower level biodiesels are efficient than diesel. Except B10, Biodiesel and other blends emitted less pollutant CO, SO₂ and CO₂ than diesel. B10 emitted lower CO₂ and NO_X, but emitted higher SO₂ than diesel. Despite studies reporting an increase in the NO_X level resulting from burning of biodiesel over conventional petroleum diesel fuels in engines, our findings indicated at the second energy level a reduction in the NO_X level in the flue gases resulting from burning of biodiesel.