Nanoclay distribution and its influence on the mechanical properties of rubber blends

The distribution of modified and unmodified nanoclays inside the rubber phases of immiscible rubber–rubber blends composed of nonpolar–polar natural rubber (NR)/epoxidized natural rubber (ENR) and nonpolar–nonpolar NR/polybutadiene rubber (BR) was investigated for the first time. The distribution of clays at various loadings in the blends was calculated from the viscoelastic properties of the blends. For example, in the 50 : 50 NR/ENR blend, 42% Cloisite 30B migrated to the NR phase, and 58% went to the ENR phase. However, in the same blend, only 7% Cloisite Na⁺ was found in the NR phase, and 93% was found in the ENR phase. Again, in the 50 : 50 NR/BR blends, the NR phase contained 85% Cloisite 30B, whereas 55% Cloisite Na⁺ migrated to the NR phase. All these observations were explained with the help of viscosity, X‐ray diffraction, and morphology analyses. The effect of the distribution of the clay on the mechanical properties was also discussed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal stability,aging properties,and flame resistance of NR‐based nanocomposite

Polymer/clay nanocomposites have some unique properties due to combination of flame resistance and improved mechanical and thermal stability properties which are important to enhance the material quality and performance. The objective of this work was to investigate the effect of organically modified montmorillonite (org‐MMT) on the thermal and flame retardant as well as hardness and mechanical properties of the nanocomposites based on the natural rubber (NR). It was shown that by the addition of 3 wt % of org‐MMT to NR, its aging hardness rise was decreased more than 55% and the ignition time was delayed about 150%. The reduction in heat release rate peak value was equal to 54% compared to the pristine NR. Addition of org‐MMT improved the thermal stability of the NR. Furthermore, nanocomposites which were calendared before curing showed much more thermal stability and fire resistance than those which contained similar amount of organoclay. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of polyimide nanocomposites with different organo‐montmorillonites

Poly(amic acid) nanocomposites were synthesized from a dimethylacetamide (DMAc) solution with two organophilic montmorillonites (organo‐MMTs). It was then heated at various temperatures under vacuum, yielding 15–20 um thick films of polyimide/organo‐MMT hybrid with different clay contents (1–8 wt%). Dodecy‐lamine (C₁₂‐) and hexadecylamine (C₁₆‐) were used as aliphatic alkylamines in organo‐MMT. The ultimate strength monotonically increased with increasing clay content in the polymer matrix. Maximum enhancement in the initial modulus was observed for the blends containing 2 wt% clay with two kinds of organo‐clays, and values did not alter significantly with further increases in clay content. Additions of only 2 wt% C₁₂‐ and C₁₆‐MMT to the polyimide were shown to cause 94%‐95% reduction in oxygen gas permeability. This is caused by the barrier properties of the clay layers dispersed in the composite. In general, C₁₆‐MMT is more effective than C₁₂‐MMT in increasing both the tensile property and the gas barrier in a polyimide matrix. Intercalations of the polymer chains in clay were examined through wide‐angle X‐ray diffraction (XRD) and electron microscopies (SEM and TEM).     

Flame retardancy and mechanical properties of polyamide 6 with melamine polyphosphate and ionic liquid surfactant‐treated montmorillonite

The mechanical properties and inflammability of polyamide 6 (PA6) nanocomposites incorporated with Montmorillonite organoclay (MMT) modified with thermal stable ionic liquid surfactants were investigated. The compatibility between ionic liquid‐treated MMT and PA6 matrix was improved and the intercalation morphology was achieved, which resulted in the increaseof tensile modulus. However, the addition of organo‐MMTs alone did not improve the inflammability of the PA6 nanocomposite, because of strong melt‐dripping behavior of PA6 matrix. Addition of auxiliary melamine polyphosphate (MPP) intumescent flame retardant to the nanocomposite prevented the melt dripping and enhanced inflammability performance. The enhanced inflammability of PA6/organoclay/MPP nanocomposites was attributed to the synergistic effect between imidazolium or phosphonium organo‐MMTs and intumescent flame retardant MPP. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40648.     

Ethylene vinyl acetate/ethylene propylene diene terpolymer‐blend‐layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA‐45)/ethylene propylene diene terpolymer (EPDM) blend‐layered double hydroxide (LDH) nanocomposites have been prepared by solution blending of 1:1 weight ratio of EVA and EPDM with varying amounts of organo LDH (DS‐LDH). X‐ray diffraction and transmission electron microscopy analysis suggest the formation of partially exfoliated EVA/EPDM/DS‐LDH nanocomposites. Measurement of mechanical properties of the nanocomposites (3 wt% DS‐LDH content) show that the improvement in tensile strength and elongation at break are 35 and 12% higher than neat EVA/EPDM blends. Dynamic mechanical thermal analysis also shows that the storage modulus of the nanocomposites at glass transition temperature is higher compared to the pure blend. Such improvements in mechanical properties have been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscopy analysis. Thermal stability of the prepared nanocomposites is substantially higher compared to neat EVA/EPDM blend, confirming the formation of high‐performance polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Development of polybutadiene (BR)–polyethylene (LDPE) blend based microcellular soles for low‐temperature applications

Microcellular (MC) soles based on polybutadiene (BR) and low‐density polyethylene (LDPE) blends for low‐temperature applications were developed. A part of BR in BR–LDPE blend was replaced by natural rubber (NR) for property improvement. The BR–NR–LDPE blend‐based MC sole shows good technical properties. Sulphur curing and DCP curing were tried in BR–LDPE and NR–BR–LDPE blends. Study shows that sulphur‐cured MC sheets possess better technical properties than DCP‐cured MC sheets. 90/10 BR–LDPE and 60/30/10 BR–NR–LDPE blend combinations are found to be suitable for low‐temperature applications. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 277–281, 2000     

Biodegradable polyester layered silicate nanocomposites based on poly(ϵ‐caprolactone)

Nanocomposites based on biodegradable poly(?‐caprolactone) (PCL) and layered silicates (montmorillonite, MMT) were prepared either by melt interaction with PCL or by in situ ring‐opening polymerization of ?‐caprolactone as promoted by the so‐called coordination‐insertion mechanism. Both non‐modified clays (Na⁺ ‐MMT) and silicates modified by various alkylammonium cations were studied. Mechanical and thermal properties were examined by tensile testing and thermogravimetric analysis. Even at a filler content as low as 3 wt% of inorganic layered silicate, the PCL‐layered silicate nanocomposites exhibited improved mechanical properties (higher Young's modulus) and increased thermal stability as well as enhanced flame retardant characteristics as a result of a charring effect. It was shown that the formation of PCL‐based nanocomposites depended not only on the nature of the ammonium cation and related functionality but also on the selected synthetic route, melt intercalation vs. in situ intercalative polymerization. Interestingly enough, when the intercalative polymerization of ?‐caprolactone was carried out in the presence of MMT organo‐modified with ammonium cations bearing hydroxyl functions, nanocomposites with much improved mechanical properties were recovered. Those hybrid polyester layered silicate nanocomposites were characterized by a covalent bonding between the polyester chains and the clay organo‐surface as a result of the polymerization mechanism, which was actually initiated from the surface hydroxyl functions adequately activated by selected tin (II) or tin (IV) catalysts.     

Effect of ultrasonically aided extrusion of NR/BR blends on structure and properties of silica‐filled compounds and vulcanizates

Ultrasonic extrusion of NR/BR blends at amplitudes up to 7.5 μm was carried out. Silica or silica/silane at loading of 60 phr was incorporated into blends to prepare compounds and vulcanizates. Effect of ultrasound on molecular structure of rubber blends, rubber–filler interaction of compounds and crosslinking structure of vulcanizates was studied. No gel was generated in NR/BR blends upon ultrasonic treatment, while earlier studies on treatment of BR alone have shown generation of gel. This finding provides means to significantly improve filler dispersion and minimize deterioration of vulcanizate properties. Processing‐structure‐properties relationship was established. Die pressure and ultrasonic power consumption were recorded. Imposition of ultrasound reduced die pressure providing potentials to increase extrusion output. No polymer degradation observed during treatment at amplitudes of 3.5 and 5 μm. A slight degradation was found at 7.5 μm leading to a decrease of storage and loss moduli of the blend, and an increase of loss tangent. Treated blends compounded with silica showed more bound rubber content, better rubber–filler interaction, reduced filler–filler interaction and less flocculation. M100 and tensile strength of NR/BR/Silica 5 μm vulcanizate was increased. In contrast, ultrasonic treatment showed little effect on NR/BR/Silica/Silane blends. The predictions related to tire performance was discussed. POLYM. ENG. SCI., 59:E261–E270, 2019. © 2018 Society of Plastics Engineers     

Improvement of the homogeneity of SBR/NBR blends using polyglycidylmethacrylate‐g‐butadiene rubber

Polyglycidylmethacrylate grafted butadiene rubber (PGMA‐g‐BR) was synthesized by a graft solution copolymerization technique. The PGMA content was determined through titration against HBr. The PGMA‐g‐BR was blended with styrene butadiene rubber/butadiene acrylonitrile rubber (SBR/NBR) blends with different blend ratios. The SBR/NBR (50/50) blend was selected to examine the compatibility of such blends. Compatibility was examined using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and viscosity measurements. The scanning electron micrographs illustrate the change of morphology of the SBR/NBR rubber blend as a result of the incorporation of PGMA‐g‐BR onto that blend. The T_gs of SBR and NBR in the blend get closer upon incorporation of PGMA‐g‐BR 10 phr, which indicates improvement in blend homogeneity. The intrinsic viscosity (η) versus blend ratio graph shows a straight‐line relationship, indicating some degree of compatibility. Thermal stability of the compatibilized and uncompatibilized rubber blend vulcanizates was investigated by determination of the physicomechanical properties before and after accelerated thermal aging. Of all the vulcanizates with different blend ratios under investigation, the SBR/NBR (25/75) compatibilized blend possessed the best thermal stability. However, the SBR/NBR (75/25) compatibilized blend possessed the best swelling performance in brake fluid. The effect of various combinations of inorganic fillers on the physicomechanical properties of that blend, before and after accelerated thermal aging, was studied in the presence and absence of PGMA‐g‐BR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1559–1567, 2006     

Preparation and characterization of elastomer‐based nanocomposite gels using an unique latex blending technique

Nanocomposite (NC) gels based on natural rubber (NR) and styrene butadiene rubber (SBR) were prepared by using a unique latex blending technique. These NC gels were prepared by first blending the water swollen unmodified montmorillonite clay (Na⁺‐MMT) suspension into the respective latices followed by prevulcanization to generate crosslinked nanogels. Use of water assisted fully delaminated Na⁺‐MMT suspension resulted in predominantly exfoliated morphology in the NC gels, as revealed by X‐ray diffraction study and transmission electron microscopy. Addition of Na⁺‐MMT significantly improved various physical, mechanical and thermal properties of these NC gels. For example, 6 phr of Na⁺‐MMT loaded NR based NC gels registered 54% and 200% increase in tensile strength and Young's modulus, respectively, compared to the unfilled NR gels. SBR based NC gels also showed similar level of improvement in mechanical properties. Mechanical properties of NC gels prepared using this route were also compared with the NC gels prepared by co‐coagulation and conventional curing technique and found to be superior. In the case of dynamic mechanical properties, NC gels showed higher glass transition temperatures along with a concomitant increase in storage moduli, compared to the unfilled gels. These Na⁺‐MMT reinforced NC gels also exhibited markedly improved thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Structural characterization of LDPE/EVA blends containing nanoclay‐flame retardant combinations

The combination of different types of organo‐modified montmorillonite (MMT) with aluminum hydroxide (aluminum trihydrate—ATH), as a flame retardant system for polyethylene‐ethylene vinyl acetate (LDPE/EVA), blends were studied. Five different types of organically modified montmorillonite clays, each with different modifier, were used. The structural characterization was carried out by X‐ray diffraction (XRD) and scanning electron microscopy in transmission mode (STEM). The mechanical and rheological properties were also evaluated. The XRD analysis showed a clear displacement of the d₀₀₁ signal, which indicates a good degree of intercalation, especially for the MMT‐I28 and MMT‐20, from Nanocor and Southern Clay Products, respectively. The presence of ATH and the compatibilizer did not have any effect on the exfoliation of the studied samples. The thermal stability and flame retardant properties were evaluated by thermogravimetric analysis (TGA), limiting oxygen index (LOI—ASTM D2863), and flammability tests (Underwriters Laboratory—UL‐94). The effect of different compatibilizers on the clay dispersion and exfoliation was studied. The results indicated that the addition of montmorillonite makes it possible to substitute part of the ATH filler content while maintaining the flame retardant requirements. The thermal stability of MMT/ATH‐filled LDPE/EVA blends presented a slight increase over the reference ATH‐filled LDPE/EVA blend. Compositions with higher clay content (10 wt %) showed better physicochemical properties. The increased stability of the higher clay content compositions results from the greater inorganic residual formation; this material has been reported to impart better performance in flammability tests. The mechanical properties and flame retardancy remained similar to those of the reference compound. The reduced ATH content resulted in lower viscosities and densities, facilitating the processing of the polymer/ATH/clay compounds. Extrusion of these compounds produced a lower pressure in the extrusion head and required reduced electrical power consumption. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal stability and aging characteristics of (natural rubber)/(waste ethylene‐propylene‐diene monomer terpolymer) blends

Comparative studies of the thermogravimetric analysis and thermo‐oxidative aging of (natural rubber)/(waste ethylene‐propylene‐diene monomer terpolymer) (NR/W‐EPDM) and (natural rubber)/(ethylene‐propylene‐diene monomer terpolymer) (NR/EPDM) blends were carried out. The blends were prepared at five different blend ratios (90/10, 80/20, 70/30, 60/40, and 50/50) on a two‐roll mill. As the pure EPDM or W‐EPDM content in the blends increased, their thermal stability also increased. The thermo‐oxidative aging of these blends was done at 100°C for 48 h. Afterwards, the NR/EPDM blends exhibited better retention of properties than the NR/W‐EPDM blends. Crosslink density measurements of the blends after thermal aging indicated that higher crosslink density was obtained from a higher content of EPDM or W‐EPDM, a result which might be due to the high rate of radical termination leading to crosslinks in the bulk of the polymer. J. VINYL ADDIT. TECHNOL., 20:99–107, 2014. © 2014 Society of Plastics Engineers     

Thermoplastic natural rubber based on polyamide‐12: Influence of blending technique and type of rubber on temperature scanning stress relaxation and other related properties

Thermoplastic natural rubber based on polyamide‐12 (PA‐12) blend was prepared by melt blending technique. Influence of blending techniques (i.e., simple blend and dynamic vulcanization) and types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends were investigated. It was found that the simple blends with the proportion of rubber ～ 60 wt % exhibited cocontinuous phase structure while the dynamically cured blends showed dispersed morphology. Furthermore, the blend of ENR exhibited superior mechanical properties, stress relaxation behavior, and fine grain morphology than those of the blend of the unmodified NR. This is attributed to chemical interaction between oxirane groups in ENR molecules and polar functional groups in PA‐12 molecules which caused higher interfacial adhesion. It was also found that the dynamic vulcanization caused enhancement of strength and hardness properties. Temperature scanning stress relaxation measurement revealed improvement of stress relaxation properties and thermal resistance of the dynamically cured ENR/PA‐12 blend. This is attributed to synergistic effects of dynamic vulcanization of ENR and chemical reaction of the ENR and PA‐12 molecules. Furthermore, the dynamically cured ENR/PA‐12 blend exhibited smaller rubber particles dispersed in the PA‐12 matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of an intercalating agent on the morphology and thermal and flame‐retardant properties of low‐density polyethylene/layered double hydroxide nanocomposites prepared by melt intercalation

The effects of an intercalating agent on the morphology and thermal and flame‐retardant properties of low‐density polyethylene (LDPE)/layered double hydroxide (LDH) nanocomposites were studied with Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, microscale combustion calorimetry, thermogravimetric analysis, and mechanical property measurements. X‐ray diffraction and transmission electron microscopy demonstrated that after intercalation with stearate anion (SA) or dodecyl sulfate anion (DS), organo‐LDH could be nanodispersed in an LDPE matrix with exfoliated structures or intercalated structures simultaneously with partially exfoliated structures, respectively, via melt intercalation. However, the unmodified LDH composites yielded only microcomposites. Microscale combustion calorimetry, thermogravimetric analysis, and dynamic Fourier transform infrared spectra showed the following order for the flame‐retardant and thermal properties: LDPE/SA‐modified LDH > LDPE/DS‐modified LDH > LDPE/NO₃‐modified LDH > LDPE. The higher performance of the LDPE/LDH nanocomposites with respect to flame retardance and thermal stability could be attributed to the better dispersion state of the LDH layers in the LDPE matrix and the greater hindrance effect of LDH layers on the diffusion of oxygen and volatile products throughout the composite materials when they were exposed to burning or thermal degradation. The tensile strength and elongation at break of the LDPE/LDH nanocomposites decreased to some extent because of the decrease in the crystallinity of the LDPE matrix. A transmittance test showed that the transparency of the exfoliated LDPE/SA‐modified LDH nanocomposite was very close to that of neat LDPE. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Silica‐modified SBR/BR blends

The purpose of this article is that the silica‐modified SBR/BR blend replaces natural rubber (NR) in some application fields. The styrene‐butadiene rubber (SBR) and cis‐butadiene rubber (BR) blend was modified, in which silica filler was treated with the r‐Aminopropyltriethoxysilane (KH‐550) as a coupling agent, to improve mechanical and thermal properties, and compatibilities. The optimum formula and cure condition were determined by testing the properties of SBR/BR blend. The properties of NR and the silica‐modified SBR/BR blend were compared. The results show that the optimum formulawas 80/20 SBR/BR, 2.5 phr dicumyl peroxide (DCP), 45 phr silica and 2.5 mL KH‐550. The best cure condition was at 150°C for 25 min under 10 MPa. The mechanical and thermal properties of SBR/BR blend were obviously modified, in which the silica filler treated with KH‐550. The compatibility of SBR/BR blend with DCP was better than those with benzoyl peroxide (BPO) and DCP/BPO. The crosslinking bonds between modified silica and rubbers were proved by Fourier transform infrared analysis, and the compatibility of SBR and BR was proved by polarized light microscopy (PLM) analysis. The silica‐modified SBR/BR blend can substitute for NR in the specific application fields. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Synthesis of exfoliated PP/LDH nanocomposites via melt‐intercalation: Structure,thermal properties,and photo‐oxidative behavior in comparison with PP/MMT nanocomposites

Exfoliated polypropylene (PP)/layered double hydroxide (LDH) nanocomposites have been successfully synthesized via melt‐intercalation. Their structure, thermal properties, and photo‐oxidative behavior have been characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), dynamic mechanical thermal analysis (DMA), X‐ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectrum. TGA and DMA data show that the PP/LDH nanocomposites have enhanced thermal stability compared with virgin PP and corresponding PP/montmorillonites (MMT) nanocomposites, especially in high temperature range during the thermal decomposition of the samples. XPS and FTIR results give positive evidence that the photo‐oxidation mechanism of PP in the PP/LDH materials is not modified compared with that of virgin PP. However, photo‐oxidation rate of PP/LDH materials is much lower than that of PP and PP/MMT samples, indicating that the PP/LDH nanocomposites have better UV‐stability. POLYM. ENG. SCI. 46:1153–1159, 2006. © 2006 Society of Plastics Engineers     

Quantitative characterization of interfaces in rubber–rubber blends by means of modulated‐temperature DSC

Rubber–rubber blends are used widely in industry, for example, in tire manufacture. It is often difficult to characterize interfaces in such rubber–rubber blends quantitatively because of the similarity in the chemical structure of the component rubbers. Here, a new method was suggested for the measurement of the weight fraction of the interface in rubber–rubber blends using modulated‐temperature differential scanning calorimetry (M‐TDSC). Quantitative analysis using the differential of the heat capacity, dCp/dT, versus the temperature signal from M‐TDSC allows the weight fraction of the interface to be calculated. As examples, polybutadiene rubber (BR)–natural rubber (NR), BR–styrene‐co‐butadiene rubber (SBR), SBR–NR, and nitrile rubber (NBR)–NR blend systems were analyzed. The interfacial content in these blends was obtained. SBR is partially miscible with BR. The cis‐structure content in BR has an obvious effect on the extent of mixing in the SBR–BR blends. With increasing styrene content in the SBR in the SBR–BR blends, the interface content decreases. NR is partially miscible with both BR and SBR. The NBR used in this research is essentially immiscible with NR. The maximum amount of interface was found to be at the 50:50 blend composition in BR–NR, SBR–BR, and SBR–NR systems. Quantitative analysis of interfaces in these blend systems is reported for the first time. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1791–1798, 2000     

Thermal stability and crystalline of electrospun polyamide 6/organo‐montmorillonite nanofibers

This research is mainly to investigate the thermal and crystalline differences between polyamide 6/montmorillonite (PA6/MMT) and polyamide 6/organo‐montmorillonite (PA6/O‐MMT) nanofibers, which were both prepared by electrospinning under the same process conditions. The structures of PA6/MMT and PA6/O‐MMT nanofibers were observed by scanning electrical microscope. It was identified that the interval between O‐MMT clays was increased in the PA6 matrix compared to that of MMT, which was detected by X‐ray diffraction (XRD). The thermal properties of PA6 nanofibers contained O‐MMT particles were more efficient than PA6/MMT nanofibers, that was verified using thermal gravimetric analysis. The crystalline properties of the electrospun nanofibers was investigated using differential scanning calorimeter and it was found that the degree of crystallinity in the PA6 nanofibers loaded with O‐MMT was much higher than PA6/MMT and PA6 nanofibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of rubber composition on change of crosslink density of rubber vulcanizates with EV cure system by thermal aging

Variation of the crosslink density of a rubber vulcanizate depending on the rubber composition after the thermal aging was studied with single rubber, biblend, and triblend vulcanizates of natural rubber (NR), butadiene rubber (BR), and styrene‐butadiene rubber (SBR). The efficient vulcanization (EV) system was employed to minimize the influence of free sulfur in the vulcanizate on the change of the crosslink density. Thermal aging was performed at 40, 60, and 80°C for 20 days with 5‐day intervals. The crosslink densities of the vulcanizates after the thermal aging increase. For the single rubber vulcanizates, variation of the crosslink density by the thermal aging has the order: SBR > BR > NR. For the biblend vulcanizates, variations of the crosslink densities of the NR/SBR and SBR/BR blends are larger than that of NR/BR blend. Variation of the crosslink density of the vulcanizate increases by increasing the SBR content in the vulcanizate. Variation of the crosslink density of the rubber vulcanizate depending on the rubber composition was explained by miscibility of the blends, combination reaction of the pendent groups, and mobility of the pendent group. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1378–1384, 2000