Nanoclay reinforced polyethylene composites: Effect of different melt compounding methods

Nanoclay (NC) reinforced high‐density polyethylene (HDPE) composites were prepared by different melt compounding methods using (1) a single screw extruder (SSE), (2) twin screw extruder (TSE), (3) a combination of SSE and extensional flow mixer (EFM), and (4) a bowl mixer masterbatch method (MB). PE‐grafted maleic anhydride (PE‐g‐MA) was used as a compatibilizer. EFM increased complex melt viscosity (η*) of the HDPE/NC composites as compared to the neat HDPE and also provided a better interaction between HDPE and NC to create slightly lower melt η* as compared to MB and PE‐g‐MA composites. The low viscosity melt behavior of the pure HDPE changes to more solid like melt behavior in the PE‐g‐MA HDPE/NC composites in the low frequency (ω) region. PE‐g‐MA + EFM method exhibited better impact strength compared to the other HDPE/NC composites. Using the PE‐g‐MA and masterbatch compounding methods had a beneficial role in improving mechanical properties. POLYM. ENG. SCI., 57:324–334, 2017. © 2016 Society of Plastics Engineers     

Effect of Al2O3 fibers on the thermal conductivity and mechanical properties of high density polyethylene with the absence and presence of compatibilizer

Alumina (Al₂O₃) fiber/high density polyethylene (HDPE) composites were prepared by molding injection with or without compatibilizer, in which, maleic anhydride‐grafted polyethylene (PE‐g‐MA) and acrylic acid‐grafted polyethylene (PE‐g‐AA) were used as the compatibilizers. The thermal conductivities of the composites were anisotropic and the conductivities in the injection direction of the samples were higher than those in perpendicular direction of the injection. The anisotropic thermal conductivity for Al₂O₃/PE‐g‐AA/HDPE was the most obvious and this composite also gave the best mechanical performance. The SEM and DMA test revealed that PE‐g‐AA was more effective than PE‐g‐MA in improving the matrix–filler interaction. The high interfacial interaction was more favorable for the viscous flow‐induced fiber orientation, which resulted in the largest anisotropic degree of thermal conductivity of the Al₂O₃/PE‐g‐AA/HDPE among the studied composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rice straw fiber reinforced high density polyethylene composite: Effect of coupled compatibilizating and toughening treatment

In this study, rice‐straw (RS) filled high density polyethylene (HDPE) composites were manufactured by extrusion and injection molding. Three compatibilizers, which are unfunctionalized ethylene/propylene copolymer (uEPR), maleic anhydride grafted EPR (EPR‐g‐MA) and PE‐g‐MA, and their combinations were introduced to strengthen fiber‐matrix interphase. The mechanical and morphological properties of composites were investigated. For single‐compatibilizer system, PE‐g‐MA or EPR‐g‐MA alone enhanced tensile, flexural, and impact strengths of resultant composites compared with HDPE/RS system without compatibilizers. Different toughening origins of individual compatibilizer were discussed based on composites' interphase morphologies and mechanical properties. For combined‐compatibilizers system, the PE‐g‐MA/EPR weight ratio is important for several properties of composites. The optimum ratio was considered as 2 : 1 and 1 : 1 for PE‐g‐MA/uEPR and PE‐g‐MA/EPR‐g‐MA modified composites, respectively. Also, composites modified by combined PE‐g‐MA/EPR‐g‐MA showed better impact strength than that modified by PE‐g‐MA alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Studies on the physico‐mechanical,thermal, and morphological behaviors of high density polyethylene/coleus spent green composites

This study is aimed at utilizing nutraceutical industrial waste and reducing carbon footprints of plastics. Eco‐friendly “green composites” of high density polyethylene (HDPE) were fabricated using coleus spent (CS)—a nutraceutical industrial waste as reinforcing filler and maleic anhydride‐graft‐polyethylene (MA‐g‐PE) as compatibilizer. Composites were fabricated with 5, 10, 15, and 20% (w/w) of CS by extrusion method. The fabricated HDPE/CS composites were evaluated for mechanical and thermal behavior. A slight improvement of about 5% in tensile strength and marked improvement of about 25% in tensile modulus for 20 wt % CS filled HDPE composites was noticed. The effect of CS content on rheological behavior was also studied. Thermal characteristics were performed using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA thermogram indicated increased thermal stability of CS‐filled composites. From TGA curves the thermal degradation kinetic parameters of the composites have been calculated using Broido's method. The enthalpy of melting (ΔH_m) obtained from DSC curves was reduced with increase in CS content in HDPE matrix, due to decrease in HDPE content in composite systems. An increase in CS loading increased the water absorption behavior of the composites slightly. Morphological behavior of cryo‐fractured composites has been studied using scanning electron microscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Creep analysis of bamboo high‐density polyethylene composites: Effect of interfacial treatment and fiber loading level

The effect of chemical treatment at fiber–plastic interface and fiber loading level on creep property of bamboo fiber high‐density polyethylene (BF/HDPE) composites was investigated. For single modifier systems, the use of maleic anhydride grafted polyethylene (PE‐g‐MA) as a coupling agent helped reduce the creep and achieved the optimum effect at the 5.7% loading level. The addition of either a semicrystalline or an amorphous MA grafted ethylene propylene rubber (sEPR‐g‐MA or aEPR‐g‐MA) as an impact modifier increased the creep. For the combined modifiers, the use of PE‐g‐MA in EPR‐g‐MA modified composites gradually improved creep performance. Four‐element Burgers model was shown to fit measured creep data well only within the specified test period. However, both partially stretched Burgers (PSB) model and fully stretched Burgers (FSB) model could be applied for characterization and prediction when the stretching exponent was fixed at certain given values. The FSB model offered a better long‐term prediction based on the short‐term creep data. Time‐temperature superposition technique produced smooth master creep curves through horizontal shifts, but it slightly over‐predicted the long‐term creep for most composite systems. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Polypropylene/silica nanocomposites prepared by in-situ melt ultrasonication

A novel process using ultrasonic irradiation to enhance nanosilica dispersion in polypropylene-based nanocomposites has been proposed and investigated. The nanocomposites were isotactic polypropylene reinforced with silica nanoparticles at 3 wt% loading level. Ultrasonic processing in the melt state is an effective method for improving nanosilica dispersion. The effectiveness of the proposed ultrasonic processing technique on polypropylene nanocomposites was evaluated by XRD and transmission electron microscopy (TEM). Poly(propylene-g-maleic anhydride) copolymer (PP-g-MAH) containing 5 wt% maleic anhydride content was added to nanocomposites at 0.5 wt% concentration based on silica content. PP-g-MAH plays an important role in nanosilica dispersion in polymer matrix and interface interaction. The reaction of maleic anhydride groups with the hydroxyl groups on the surface of nanosilica was characterized by FTIR spectrum. The final nanocomposites result in a further enhancement of mechanical properties because of silica agglomerate reduction and improving interface combination, even loading level being much lower than that of ordinary fillers in conventional composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Environmental weathering of (linear low‐density polyethylene)/(soya powder) blends compatibilized with polyethylene‐grafted maleic anhydride

Blends containing various percentages of linear low‐density polyethylene and soya powder were prepared. The effects of polyethylene‐graft‐(maleic anhydride) (PE‐g‐MA) as a compatibilizer and soya powder content on the natural weathering were investigated. Blends without PE‐g‐MA were used as controls. The soya powder was varied from 5 to 40 wt% of the blends, and PE‐g‐MA was used at 50 wt% based on soya powder content. The samples were exposed to natural weathering in the northern part of Malaysia for 1 year. Higher decreases in tensile strength and elongation at break of the controls were observed as compared to those of the PE‐g‐MA compatibilized blends after the natural weathering. The Young's modulus of both controls and compatibilized blends increased over the environmental exposure period. A control sample lost 8.8% of its original weight after 1 year of weathering, whereas a compatibilized blend lost 7.5 wt% during the same period. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Encapsulated phase structure and morphology evolution during quiescent annealing in ternary polymer blends with PA6 as matrix

This work is aim to study the encapsulated morphology development in ternary blends of polyamide 6/high density polyethylene/maleic anhydride‐grafted‐ethylene propylene diene monomer (PA6/HDPE/EPDM‐g‐MA) and polyamide 6/maleic anhydride‐grafted‐high density polyethylene/ethylene propylene diene monomer (PA6/HDPE‐g‐MA/EPDM) through thermodynamically control described by Harkins spreading theory. The phase morphology was confirmed by using scanning electron microscope (SEM) and selective solvent extraction revealed that PA6/HDPE/EPDM‐g‐MA blend having a composition of 70/15/15 vol % is constituted of polyamide 6 matrix with dispersed composite droplets of HDPE subinclusions encapsulated by EPDM‐g‐MA phase, while for PA6/HDPE‐g‐MA/EPDM blend with the same composition is constituted of polyamide 6 matrix with dispersed composite droplets of HDPE‐g‐MA subinclusions encapsulated by EPDM phase. Quiescent annealing test revealed that for PA6/HDPE/EPDM‐g‐MA blend, a perfect core–shell structure with one HDPE particle encapsulated by EPDM‐g‐MA phase was formed during annealing, and for PA6/HDPE‐g‐MA/EPDM blend, a novel complete inverting HDPE‐g‐MA/EPDM core/shell structure was achieved. Moreover, quantitative analysis about coalescent behaviors of HDPE‐g‐MA and HDPE subinclusions during quiescent annealing were investigated by image analysis and the result suggested that the grafted maleic anhydride group in HDPE‐g‐MA, acted as a role of steric repulsion, could suppress coalescence effects, thus leaded to a lower coalescent rate than that of HDPE subinclusions. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39937.     

Mechanical properties of wood flake–polyethylene composites. II. Interface modification

This article discusses the methods of interface modification of composites based on raw wood flakes and high‐density polyethylene (HDPE) and the effects of these modifications on composite properties. An HDPE matrix was modified by a reaction with maleic anhydride (MA) in a twin‐screw extruder and then compounded with wood flakes to produce wood–polyethylene composites. Wood flakes were modified by a reaction with a silane coupling agent in an aqueous medium before being compounded with HDPE to produce silane‐modified WPCs. Differential scanning calorimetry and Fourier transform infrared spectroscopy data provide evidence for the existence of a polyethylene (PE)–silane‐grafted wood structure, which acts as a compatibilizer for wood flakes and PE. The results of MA‐modified composites indicate that some maleated HDPE is reacting with wood through esterification to form a compatibilizer for wood flakes and HDPE. Significant improvements in tensile strength, ductility, and Izod impact strength were obtained. Scanning electron micrographs provide evidence for strong interactions between the wood flakes and the matrix agent. The results indicate that 1–2 wt % MA modification on HDPE and 1–3 wt % silane treatment on wood flakes provide WPCs with the optimum properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2505–2521, 2002     

Effect of chemical modification of oil fly ash and compatibilization on the rheological and morphological properties of low‐density polyethylene composites

In this study, the effect of oil fly ash (OFA), a by‐product of oil fuel power plants, on the rheological and morphological behavior of low‐density polyethylene (LDPE) is investigated. As received and acid‐functionalized OFA (COOH‐OFA) are used to examine the effect of surface modification of OFA on polymer–filler composites. LDPE/OFA composites were prepared by melt mixing with filler loading in the range 1–10 wt %. The results are compared with pure LDPE. The effect of polyethylene‐grafted‐maleic anhydride (PE‐g‐MA) as a compatibilizer was also studied. Both viscous and elastic properties of composites increased with OFA loading especially at low frequency. The surface modification of OFA has influenced the properties of OFA. As‐received OFA showed some agglomeration at high loading that resulted in two‐phase system as described by scanning electron microscopy (SEM) and Cole–Cole plot. Field emission‐SEM (FE‐SEM) images showed improvement in the dispersion of COOH‐LDPE/OFA composites. In addition, the surface modification reduced the size of agglomeration. In general, the COOH modification of OFA improved both the dispersion and rheological properties of OFA. With chemical modification, the concentration of the filler can be increased to 10% without compromising the properties of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Polyethylene/sepiolite clay nanocomposites: Effect of clay content,compatibilizer polarity,and molar mass on viscoelastic and dynamic mechanical properties

In this work, high‐density polyethylene (HDPE)‐based nanocomposites having different concentrations of Sepiolite (1–10 wt %) and compatibilizer, that is, PE‐graft‐maleic anhydride (PE‐g‐MA) of varying molecular weight and maleic anhydride content were prepared by melt compounding. The influence of Sepiolite amount and compatibilizer polarity and molar mass on the crystallization behavior [differential scanning calorimeter (DSC) and X‐ray diffraction (XRD)], rheological properties (oscillatory rheometer) and dimensional stability [dynamic mechanical analyzer (DMA) and heat deflection temperature (HDT)] of the nanocomposites was investigated. It was found that Sepiolite did not affect the crystallization behavior of HDPE. The rheological results show that the incorporation of Sepiolite into HDPE matrix up to 10 wt % increases the complex viscosity of polymer. Storage modulus and loss modulus both in oscillatory rheometry and in DMA were highest for nanocomposite prepared using 10 wt % Sepiolite owing to the improved mechanical restrain by the dispersed phase. In the presence of compatibilizer, the values of storage modulus and loss modulus were lower as compared to uncompatibilized nanocomposites at same loading of Sepiolite. The reduction in modulus is more pronounced in composites prepared using compatibilizer of lower molar mass as compared to those prepared using higher molar mass compatibilizer. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45197.     

Synergistic compatibilization and reinforcement of HDPE/wood flour composites

Multi‐monomer grafted copolymers, high‐density polyethylene‐grafted‐maleic anhydride‐styrene (HDPE‐g‐(MAH‐St)) and polyethylene wax‐grafted‐ maleic anhydride ((PE wax)‐g‐MAH), were synthesized and applied to prepare high‐performance high‐density polyethylene (HDPE)/wood flour (WF) composites. Interfacial synergistic compatibilization was studied via the coordinated blending of high‐density polyethylene‐grafted‐maleic anhydride (MPE‐St) and polyethylene wax‐grafted‐ maleic anhydride (MPW) in the high‐density polyethylene (HDPE)/wood flour (WF) composites. Scanning electron microscopy (SEM) morphology and three‐dimensional WF sketch presented that strong interactive interface between HDPE and WF, formed by MPE‐St with high graft degree of maleic anhydride (MAH) together with the permeating effect of MPW with a low molecular weight. Experimental results demonstrated that HDPE/WF composites compatibilized by MPE‐St/MPW compounds showed significant improvement in mechanical properties, rheological properties, and water resistance than those compatibilized by MPE, MPE‐St or MPW separately and the uncompatibilized composites. The mass ratio of MPE‐St/MPW for optimizing the HDPE/WF composites was 5:1. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42958.     

Gasoline permeation behavior and mechanical properties of polyamide 6/nanoclay,polyamide 6/PE‐g‐maleic anhydride blend,and polyamide 6/PE‐g‐maleic anhydride/clay nanocomposite

In this article, polyamide 6 (PA6)/clay nanocomposites, PA6/polyethylene grafted maleic anhydride (PE‐g‐MA) blends, and PA6/PE‐g‐MA/clay nanocomposites were prepared and their gasoline permeation behavior and some mechanical properties were investigated. In PA6/clay nanocomposites, cloisite 30B was used as nanoparticles, with weight percentages of 1, 3, and 5. The blends of PA6/PE‐g‐MA were prepared with PE‐g‐MA weight percents of 10, 20, and 30. All samples were prepared via melt mixing technique using a twin screw extruder. The results showed that the lowest gasoline permeation occurred when using 3 wt % of nanoclay in PA6/clay nanocomposites, and 10 wt % of PE‐g‐MA in PA6/PE‐g‐MA blends. Therefore, a sample of PA6/PE‐g‐MA/clay nanocomposite containing 3 wt % of nanoclay and 10 wt % of PE‐g‐MA was prepared and its gasoline permeation behavior was investigated. The results showed that the permeation amount of PA6/PE‐g‐MA/nanoclay was 0.41 g m^?2 day^?1, while this value was 0.46 g m^?2 day^?1 for both of PA6/3wt % clay nanocomposite and PA6/10 wt % PE‐g‐MA blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40150.     

Effects of different compatibilizers on the rheological,thermomechanical, and morphological properties of HDPE/LLDPE blend‐based nanocomposites

The influence of two different compatibilizers and their combination (maleic anhydride grafted high density polyethylene, HDPE‐g‐MA; maleic anhydride grafted linear low density polyethylene, LLDPE‐g‐MA; and 50/50 wt % mixture of these compatibilizers) on the rheological, thermomechanical, and morphological properties of HDPE/LLDPE/organoclay blend‐based nanocomposites was evaluated. Nanocomposites were obtained by melt‐intercalation in a torque rheometer in two steps. Masterbatches (compatibilizer/nanoclay 2:1) were obtained and subsequently diluted in the HDPE/LLDPE matrix producing nanocomposites with 2.5 wt % of nanoclay. Wide angle X‐ray diffraction (WAXD), steady‐state rheological properties, and transmission electron microscopy (TEM) were used to determine the influence of different compatibilizer systems on intercalation and/or exfoliation process which occurs preferentially in the amorphous phase, and thermomechanical properties. The LLDPE‐g‐MA with a high melt index (and consequently low viscosity and crystallinity) was an effective compatibilizer for this system. Furthermore, the compatibilized nanocomposites with LLDPE‐g‐MA or mixture of HDPE‐g‐MA and LLDPE‐g‐MA exhibited better nanoclay's dispersion and distribution with stronger interactions between the matrix and the nanoclay. These results indicated that the addition of maleic anhydride grafted polyethylene facilitates both, the exfoliation and/or intercalation of the clays and its adhesion to HDPE/LLDPE blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1726–1735, 2013     

Structural,thermal, and gas transport properties of HDPE/LLDPE blend‐based nanocomposites using a mixture of HDPE‐g‐MA and LLDPE‐g‐MA as compatibilizer

Nanocomposites based on high density polyethylene (HDPE)/linear low density polyethylene (LLDPE) blend were prepared by melt compounding in a twin‐screw extruder using organoclay (montmorillonite) as nano‐filler and a 50/50 wt% mixture of maleic anhydride functionalized high density polyethylene (HDPE‐g‐MA) and linear low density polyethylene (LLDPE‐g‐MA) as the compatibilizing system. The addition of a maleated polyethylene‐based compatibilizing system was required to improve the organoclay dispersion in the HDPE/LLDPE blend‐based nanocomposite. In this work, the relationships between thermal properties, gas transport properties, and morphology were correlated. The compatibilized nanocomposite exhibited an intercalated morphology with a small number of individual platelets dispersed in the HDPE/LLDPE matrix, leading to an significant decrease in the oxygen permeation coefficient of the nanocomposites. A decrease in the carbon dioxide permeability and oxygen permeability with increase of nanoclay was observed for the compatibilized nanocomposites. The carbon dioxide permeability of the compatibilized nanocomposites was lower than the carbon dioxide permeability of the uncompatibilized nanocomposites even with the low intrinsic barrier properties of the compatibilizer. These effects were attributed to a good dispersion of the inorganic filler, good wettability of the filler by the polymer matrix, and strong interactions at the interface that increased the tortuous path for diffusion. Theoretical permeability models were used to estimate the final aspect ratio of nanoclay in the nanocomposite and showed good agreement with the aspect ratio obtained directly from TEM images. POLYM. ENG. SCI., 56:765–775, 2016. © 2016 Society of Plastics Engineers     

The effect of maleic anhydride grafting efficiency on the flexural properties of polyethylene composites

Many authors have reported on the property enhancements possible by compounding high density polyethylene (HDPE) with fillers to produce composites. It is accepted that polyethylene combined with materials such as nanoclay or wood flour will not yield favorable properties unless a compatibilizing material is used to form a link. In this work, compatibilized HDPE was produced by grafting maleic anhydride (MA) to its backbone in a twin screw extruder using a peroxide initiated reactive process. Fourier transform infrared spectroscopy (FTIR) was used to examine the effects of varying peroxide and MA levels on the grafting percentage and it was found that a high percentage could be achieved. The gel content of each HDPE‐g‐MA batch was determined and twin bore rheometry analysis was carried out to examine the effects of crosslinking and MA grafting on the melt viscosity. These HDPE‐g‐MA compatibilizers were subsequently compounded with nanoclay and wood flour to produce composites. The composite materials were tested using a three point bending apparatus to determine the flexural modulus and strength and were shown to have favorable mechanical properties when compared with composites containing no compatibilizer. X‐ray diffraction (XRD) was used to examine the effects of grafted MA content on the intercalation and exfoliation levels of nanoclay composites. The results from XRD scans showed that increased intercalation in polymer nanoclay composites was achieved by increasing the grafted MA content. This was confirmed using a scanning electron microscope, where images produced showed increased levels of dispersion and reductions in nanoclay agglomerates. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nanocomposites of silica reinforced polypropylene: Correlation between morphology and properties

Polypropylene/fumed hydrophilic silica nanocomposites were prepared via melt mixing method using a single‐screw extruder. Comparative study with and without compatibilizing copolymer agent (maleic anhydride grafted polypropylene: PP‐g‐AM) was conducted. The obtained results were interpreted in terms of silica nanoparticle–silica nanoparticle and silica nanoparticle‐polymer interactions. These results have shown that the addition of nanofillers improves the properties of the nanocomposites. From transmission electron microscopy, it was found that agglomerations of silica particles into the PP matrix increased in average size with increasing silica contents, except in presence of the copolymer. Storage modulus values of the nanocomposites measured by dynamic mechanical thermal analysis were sensitive to the microstructure of the nanocomposites. Higher silica contents resulted in higher storage modulus, revealing that the material became stiffer. By adding the compatibilizer, a further increase of storage modulus was observed due to the finer dispersion of the filler in the matrix and the increased interfacial adhesion. Crystallization rates were found to increase with the increase of silica nanoparticles as well as PP‐g‐MA content. In addition, silica nanoparticles and the compatibilizing agent present centers of germination and nucleation of crystallites. Thus, the use of the coupling agent resulted in a further enhancement of mechanical properties of the nanocomposites due to the reduction of silica agglomeration. POLYM. ENG. SCI., 54:2187–2196, 2014. © 2013 Society of Plastics Engineers