Preparation of diblock copolymers consisting of methoxy poly(ethylene glycol) and poly(ε‐caprolactone)/poly(L‐lactide) and their degradation property

Methoxy poly(ethylene glycol)‐b‐poly(ε‐caprolactone) (MPEG‐PCL) or MPEG‐b‐poly(L ‐lactide) (MPEG‐PLLA) diblock copolymers were prepared by the polymerization of CL or LA, using MPEG as an initiator in the presence of stannous octoate. MPEG‐b‐poly(ε‐caprolactone‐ran‐L ‐lactide) (MPEG‐PCLA) diblock copolymers with different chemical composition of PCL and PLLA were also prepared by adjusting the amount of CL and LA from MPEG in the presence of stannous octoate. In degradation study, the degradation of the MPEG‐PCLA diblock copolymers mainly depends on the PCL and PLLA segments present in their structure. MPEG‐PCLA, with intermediate ratio of PCL and PLLA segment, completely degraded after 14 weeks. Meanwhile, partially degraded MPEG‐PCLA segments and parent MPEG segments were observed at higher PCL or PLLA segment contents. Introduction of PLLA into the PCL segments caused a lowering of the crystallinity of the diblock copolymers, thus, inducing a faster incoming of water into the copolymers. We confirmed that the diblock copolymers, with lower degree of crystallinity, have degraded more rapidly. POLYM. ENG. SCI., 46: 1242–1249, 2006. © 2006 Society of Plastics Engineers     

Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

Blends of aliphatic polyesters. VIII. Effects of poly(L‐lactide‐co‐ε‐caprolactone) on enzymatic hydrolysis of poly(L‐lactide), poly(ε‐caprolactone), and their blend films

Poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their blend (50/50) films containing different amounts of poly(L ‐lactide‐co‐ε‐caprolactone) (PLLA‐CL), were prepared by solution casting. The effects of added PLLA‐CL on the enzymatic hydrolysis of the films were investigated in the presence of proteinase K and Rhizopus arrhizus lipase by use of gravimetry. The addition of PLLA‐CL decreased the proteinase K–catalyzed hydrolyzabilities of the PLLA and PLLA/PCL (50/50) films as well as the Rhizopus arrhizus lipase‐catalyzed hydrolyzability of the PCL and PLLA/PCL (50/50) films. The decreased enzymatic hydrolyzabilities of the PLLA and PCL films upon addition of PLLA‐CL are attributable to the fact that the PLLA‐CL is miscible with PLLA and PCL and the dissolved PLLA‐CL must disturb the adsorption and/or scission processes of the enzymes. In addition to this effect, the decreased enzymatic hydrolyzabilities of the PLLA/PCL (50/50) films upon addition of PLLA‐CL can be explained by the enhanced compatibility between the PLLA‐rich and PCL‐rich phases arising from the dissolved PLLA‐CL. These effects result in decreased hydrolyzable interfacial area for PLLA/PCL films. The decrement in proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PLLA‐CL, which is miscible with PLLA, was in marked contrast with the enhanced proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PCL, which is immiscible with PLLA. This confirms that the miscibility of the second polymer is crucial to determine the proteinase K–catalyzed hydrolyzabilities of the PLLA‐based blend films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 412–419, 2003     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Characterization of the mechanical and thermal properties and morphological behavior of biodegradable poly(L‐lactide)/poly(ε‐caprolactone) and poly(L‐lactide)/poly(butylene succinate‐co‐L‐lactate) polymeric blends

Two series of biodegradable polymer blends were prepared from combinations of poly(L ‐lactide) (PLLA) with poly(?‐caprolactone) (PCL) and poly(butylene succinate‐co‐L ‐lactate) (PBSL) in proportions of 100/0, 90/10, 80/20, and 70/30 (based on the weight percentage). Their mechanical properties were investigated and related to their morphologies. The thermal properties, Fourier transform infrared spectroscopy, and melt flow index analysis of the binary blends and virgin polymers were then evaluated. The addition of PCL and PBSL to PLLA reduced the tensile strength and Young's modulus, whereas the elongation at break and melt flow index increased. The stress–strain curve showed that the blending of PLLA with ductile PCL and PBSL improved the toughness and increased the thermal stability of the blended polymers. A morphological analysis of the PLLA and the PLLA blends revealed that all the PLLA/PCL and PLLA/PBSL blends were immiscible with the PCL and PBSL phases finely dispersed in the PLLA‐rich phase. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrospun poly(L‐lactide)/poly(ε‐caprolactone) blend fibers and their cellular response to adipose‐derived stem cells

Polymer blending is one of the most effective methods for providing new, desirable biocomposites for tissue‐engineering applications. In this study, electrospun poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) blend fibrous membranes with defect‐free morphology and uniform diameter were optimally prepared by a 1 : 1 ratio of PLLA/PCL blend under a solution concentration of 10 wt %, an applied voltage of 20 kV, and a tip‐to‐collector distance of 15 cm. The fibrous membranes also showed a porous structure and high ductility. Because of the rapid solidification of polymer solution during electrospinning, the crystallinity of electrospun PLLA/PCL blend fibers was much lower than that of the PLLA/PCL blend cast film. To obtain an initial understanding of biocompatibility, adipose‐derived stem cells (ADSCs) were used as seed cells to assess the cellular response, including morphology, proliferation, viability, attachment, and multilineage differentiation on the PLLA/PCL blend fibrous scaffold. Because of the good biocompatibility and nontoxic effect on ADSCs, the PLLA/PCL blend electrospun fibrous membrane provided a high‐performance scaffold for feasible application in tissue engineering using ADSCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Radiation‐induced effects in gamma‐irradiated PLLA and PCL at ambient and dry ice temperatures

The effect of γ‐rays sterilization at ambient (23°C) and at dry ice temperatures (?78°C) on two biodegradable semicrystalline polyesters, namely poly(L ‐lactide) (PLLA) and poly(ε‐caprolactone) (PCL), was studied. The radical processes generated by irradiation were investigated by electron paramagnetic resonance (EPR) spectroscopy, whereas postradiation changes were monitored for 5 months by scanning calorimetry, thermogravimetric analysis, and apparent viscosity measurements. It was confirmed that the radiation sterilization initiates degradation in both studied polymers, however, the effect is smaller in PCL than in PLLA, and that the range of changes might be limited by lowering temperature of the exposure to γ‐rays. Newly formed oxygen containing functional groups confirmed by EPR and thermogravimetric analysis methods are produced in the irradiated polyesters. In PCL, the process might give rise to thermally induced cross‐linking via oxygen containing intermolecular bridges. During storage, in both irradiated materials, morphology determined by differential scanning calorimetry is changing ‐ PCL ability toward crystallization decreases insignificantly, whereas in PLLA the tendency is opposite ‐ on irradiation a contribution of crystalline phase is growing considerably, from 18 and 19% to 41 and 31% for PLLA irradiated at 23°C and at ?78°C, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Toward environment‐friendly composites of poly(ε‐caprolactone) reinforced with stereocomplex‐type poly(l‐lactide)/poly(d‐lactide)

In this work, stereocomplex‐poly(l ‐ and d ‐lactide) (sc‐PLA) was incorporated into poly(ε‐caprolactone) (PCL) to fabricate a novel biodegradable polymer composite. PCL/sc‐PLA composites were prepared by solution casting at sc‐PLA loadings of 5–30 wt %. Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) demonstrated the formation of the stereocomplex in the blends. DSC and WAXD curves also indicated that the addition of sc‐PLA did not alter the crystal structure of PCL. Rheology and mechanical properties of neat PCL and the PCL/sc‐PLA composites were investigated in detail. Rheological measurements indicated that the composites exhibited evident solid‐like response in the low frequency region as the sc‐PLA loadings reached up to 20 wt %. Moreover, the long‐range motion of PCL chains was highly restrained. Dynamic mechanical analysis showed that the storage modulus (E′) of PCL in the composites was improved and the glass transition temperature values were hardly changed after the addition of sc‐PLA. Tensile tests showed that the Young's modulus, and yield strength of the composites were enhanced by the addition of sc‐PLA while the tensile strength and elongation at break were reduced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40208.     

Effect of P(lLA‐co‐εCL) on the compatibility and crystallization behavior of PCL/PLLA blends

This article describes the compatibility of two semicrystalline polymers, poly(ε‐caprolactone) (PCL) and poly(l‐lactic acid) (PLLA). The compatibility of the PCL/PLLA blends was enhanced by the compatibilizing effect of the poly(l,l‐lactide‐co‐ε‐caprolactone) [P(lLA‐co‐εCL)]. A discussion details the effect of the concentration of the compatibilizing agent, the copolymer of l,l‐lactide and ε‐caprolactone of a 50/50 mol ratio [P(lLA‐co‐εCL)], on the compatibility and the crystallization behavior of the blends of PCL and PLLA. It was found that the addition of P(lLA‐co‐εCL) could suppress the crystallization of PLLA at its T_c and induced the concurrent crystallization of PLLA and PCL. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 226–231, 2000     

Preparation,characterization, and drug release behaviors of drug‐loaded ε‐caprolactone/L‐lactide copolymer nanoparticles

Copolymers of ε‐caprolactone and L ‐lactide (PCLLA) with different monomer ratio were synthesized by ring opening polymerization, and drug‐loaded nanoparticles of poly‐ε‐caprolactone (PCL), poly‐L ‐lactide (PLLA), and their copolymers were prepared by precipitation method, respectively. The results of differential scanning calorimetry and X‐ray diffraction indicated that the copolymerization of PCLLA decreased the crystallinity of the polymers, and the results of transmission electron micrograph and laser light scattering (LLS) revealed that the prepared nanoparticles had a spherical shape, and the size of PCLLA nanoparticles (∼ 85 nm) was smaller than that of the PCL and PLLA nanoparticles. The experiment of in vitro drug release showed that the drug release rate from PCLLA nanoparticles was slower than that from PCL and PLLA nanoparticles, and the release profile of PCL6/LA4 nanoparticles appeared to follow zero order kinetics. These results suggested that the polymer composition made a great influence on the nanoparticle size and drug release behavior. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 874–882, 2000     

Synthesis,characterization and biocompatibility of novel biodegradable poly[((R)‐3‐hydroxybutyrate)‐block‐(D,L‐lactide)‐block‐(ε‐caprolactone)] triblock copolymers

BACKGROUND: Biodegradable block copolymers have attracted particular attention in both fundamental and applied research because of their unique chain architecture, biodegradability and biocompatibility. Hence, biodegradable poly[((R )‐3 ‐hydroxybutyrate)‐block‐(D ,L ‐lactide)‐block‐(ε‐caprolactone)] (PHB‐PLA‐PCL) triblock copolymers were synthesized, characterized and evaluated for their biocompatibility. RESULTS: The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and thermogravimetric analysis showed that the novel triblock copolymers were successfully synthesized. Differential scanning calorimetry and wide‐angle X‐ray diffraction showed that the crystallinity of PHB in the copolymers decreased compared with methyl‐PHB (LMPHB) oligomer precursor. Blood compatibility experiments showed that the blood coagulation time became longer accompanied by a reduced number of platelets adhering to films of the copolymers with decreasing PHB content in the triblocks. Murine osteoblast MC3T3‐E1 cells cultured on the triblock copolymer films spread and proliferated significantly better compared with their growth on homopolymers of PHB, PLA and PCL, respectively. CONCLUSION: For the first time, PHB‐PLA‐PCL triblock copolymers were synthesized using low molecular weight LMPHB oligomer as the macroinitiator through ring‐opening polymerization with D ,L ‐lactide and ε‐caprolactone. The triblock copolymers exhibited flexible properties with good biocompatibility; they could be developed into promising biomedical materials for in vivo applications. Copyright © 2008 Society of Chemical Industry     

Investigation of the interaction of CO2 with poly (L‐lactide), poly(DL‐lactide) and poly(ε‐caprolactone) using FTIR spectroscopy

Fourier transform infrared (FTIR) spectroscopy was used to reveal intermolecular interactions between carbon dioxide (CO₂) and the carbonyl groups of poly(L ‐lactide) (PLLA), poly(D,L ‐lactide) (PDLLA), and poly(ε‐caprolactone) (PCL). After exposing polymer films to high pressure CO₂, the wave number of the absorption maxima of the polymer carbonyl groups shifted to higher values. Also, due to the interaction between CO₂ and the carbonyl groups of the polymers, a new broad peak in the bending mode region of CO₂ appeared. To distinguish between polymer‐associated and nonassociated CO₂, and to quantify these contributions, the bending mode peaks were deconvoluted. From these contributions, it was found that in the case of PCL more CO₂ is interacting with the polymer carbonyl groups than in the case of PDLLA and PLLA. Under our experimental conditions, 40°C and pressures up to 8 MPa, a significant depression of the PCL melting temperature was observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Melt‐processed biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): Effects of processing conditions on biodegradation

Biodegradable polyester blends were prepared from poly(L ‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) (50/50) by melt‐blending, and the effects of processing conditions (shear rate, time, and strain) of melt‐blending on proteinase‐K‐ and lipase‐catalyzed enzymatic degradability were investigated using gravimetry, differential scanning calorimetry, and scanning electron microscopy. The proteinase‐K‐catalyzed degradation rate of the blend films increased and leveled off with increasing the shear rate, time, or strain for melt‐blending, except for the shortest shear time of 60 s. The optimal processing conditions of melt‐blending giving the maximum rate of lipase‐catalyzed degradation were 9.6 × 10² s^?1 and 180 s, whereas a deviation from these conditions caused a reduction in lipase‐catalyzed enzymatic degradation rate. At the highest shear rate of 2.2 × 10³ s^?1, PCL‐rich phase was continuous in the blend films, irrespective of the shear time (or shear strain), whereas PLLA‐rich phase changed from dispersed to continuous by increasing the shear time (or shear strain). This study revealed that the biodegradability of PLLA/PCL blend materials can be manipulated by altering the processing conditions of melt‐blending (shear rate, time, or strain) or the sizes and morphology of PLLA‐rich and PCL‐rich domains. The method reported in the present study can be utilized for controlling the biodegradability of other biodegradable polyester blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 831–841, 2007     

Effect of bisphenol A on the miscibility,phase morphology,and specific interaction in immiscible biodegradable poly(ε‐caprolactone)/poly(L‐lactide) blends

We have investigated the enhancement in miscibility, upon addition of bisphenol A (BPA) of immiscible binary biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(L ‐lactide) (PLLA). That BPA is miscible with both PCL and PLLA was proven by the single value of T_g observed by differential scanning calorimetry (DSC) analyses over the entire range of compositions. At various compositions and temperatures, Fourier transform infrared spectroscopy confirmed that intermolecular hydrogen bonding existed between the hydroxyl group of BPA and the carbonyl groups of PCL and PLLA. The addition of BPA enhances the miscibility of the immiscible PCL/PLLA binary blend and transforms it into a miscible blend at room temperature when a sufficient quantity of the BPA is present. In addition, optical microscopy (OM) measurements of the phase morphologies of ternary BPA/PCL/PLLA blends at different temperatures indicated an upper critical solution temperature (UCST) phase diagram, since the ΔK effect became smaller at higher temperature (200°C) than at room temperature. An analysis of infrared spectra recorded at different temperatures correlated well with the OM analyses. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1146–1161, 2006     

Synthesis of star‐shaped poly(ε‐caprolactone)‐b‐poly(L‐lactide) copolymers: From star architectures to crystalline morphologies

Hexa‐armed star‐shaped poly(ε‐caprolactone)‐block‐poly(L ‐lactide) (6sPCL‐b‐PLLA) with dipentaerythritol core were synthesized by a two‐step ring‐opening polymerization. GPC and ¹H NMR data demonstrate that the polymerization courses are under control. The molecular weight of 6sPCLs and 6sPCL‐b‐PLLAs increases with increasing molar ratio of monomer to initiator, and the molecular weight distribution is in the range of 1.03–1.10. The investigation of the melting and crystallization demonstrated that the values of crystallization temperature (T_c), melting temperature (T_m), and the degree of crystallinity (X_c) of PLLA blocks are increased with the chain length increase of PLLA in the 6sPCL‐b‐PLLA copolymers. On the contrary, the crystallization of PCL blocks dominates when the chain length of PLLA is too short. According to the results of polarized optical micrographs, both the spherulitic growth rate (G) and the spherulitic morphology are affected by the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Largely improved tensile extensibility of poly(L‐lactic acid) by adding poly(ε‐caprolactone)

Poly(L ‐lactic acid) (PLLA) has good biocompatibility, biodegradability and physical properties. However, one of the drawbacks of PLLA is its brittleness due to the stiff backbone chain. In this work, a largely improved tensile toughness (extensibility) of PLLA was achieved by blending it with poly(ε‐caprolactone) (PCL). To obtain a good dispersion of PCL in the PLLA matrix, blends were prepared via a solution‐coagulation method. An increase in extensibility of PLLA of more than 20 times was observed on adding only 10 wt% of PCL, accompanied by a slight decrease in tensile strength. However, annealing of the samples led to a sharp decrease of extensibility due to phase separation and a change of crystalline structure. To conserve the good mechanical properties of PLLA/PCL blends, the blends were crosslinked via addition of dicumyl peroxide during the preparation process. For the crosslinked blend films, the extensibility was maintained nearly at the original high value even after annealing. Morphological analysis of cryo‐fractured and etched‐smoothed surfaces of the PLLA/PCL blends was carried out using scanning electron microscopy. Differential scanning calorimetry and polarized light microscopy experiments were used to check the possible change of crystallinity, melting point and crystal morphology for both PLLA and PCL after annealing. The results indicated that the combination of solution‐coagulation and crosslinking resulted in a good and stable dispersion of PCL in the PLLA matrix, which is considered as the main reason for the observed improvement of tensile toughness. Copyright © 2010 Society of Chemical Industry     

Disclosing the crystallization behavior and morphology of poly(ϵ‐caprolactone) within poly(ϵ‐caprolactone)/poly(l‐lactide) blends

In this work, the effect of poly(l ‐lactide) (PLLA) components on the crystallization behavior and morphology of poly(?‐caprolactone) (PCL) within PCL/PLLA blends was investigated by polarized optical microscopy, DSC, SEM and AFM. Morphological results reveal that PCL forms banded spherulites in PCL/PLLA blends because the interaction between the two polymer components facilitates twisting of the PCL lamellae. Additionally, the average band spacing of PCL spherulites monotonically decreases with increasing PLLA content. With regard to the crystallization behaviors of PCL, the crystallization ability of PCL is depressed with increase of the PLLA content. However, it is interesting to observe that the growth rate of PCL spherulites is almost independent of the PLLA content while the overall isothermal crystallization rate of PCL within PCL/PLLA blends decreases first and then increases at a given crystallization temperature, indicating that the addition of PLLA components shows a weak effect on the growth rate of the PCL but mainly on the generation of nuclei. © 2018 Society of Chemical Industry     

Preparation of high toughness and high transparency polylactide blends resin based on multiarmed polycaprolactone‐block‐poly(l‐lactide)

Modification of poly(l ‐lactide) (PLLA) via blending with two or more polymers is one of the effective approaches used to overcome the brittleness of PLLA, which often requires the addition of a compatibilizer and generate opaque materials. To solve this problem, multiarmed polycaprolactone‐block‐PLLA (PCL‐b‐PLLA) was synthesized by consecutive ring‐opening polymerization of ε‐caprolactone and l ‐lactide using multihydroxyl alcohols as initiator. The structure and composition was confirmed by proton nuclear magnetic resonance and gel permeation chromatography. PLLA/multiarmed PCL‐b‐PLLA blends with various blend ratios were prepared via melt mixing. The presence of multiarmed PCL‐b‐PLLA (30%) in the PLLA matrix exhibited more than 80 times improvement in the elongation at break, as compared to unmodified PLLA. The addition of multiarmed PCL‐b‐PLLA in the PLLA contributed to the enhancement of the storage modulus in the low frequency, which was related to the entanglement of the PLLA and multiarmed PCL‐b‐PLLA. The blend interface had no obvious phase separation, and showed good adhesion between dispersed block copolymer phases within the continuous PLLA phase. The compatibilization mechanism and toughing mechanism were proposed. The resulting PLLA blends also showed good transparency. The current research opened a new route available to prepare transparent PLA‐based resin with enhanced properties. POLYM. ENG. SCI., 56:1125–1137, 2016. © 2016 Society of Plastics Engineers     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009