Hybrid composites of ABS with carbonaceous fillers for electromagnetic shielding applications

This work evaluates the influence of two types of carbonaceous fillers, carbon black (CB) and carbon nanotubes (CNTs), on the electrical, electromagnetic, and rheological properties of composites based on poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) prepared by the melt mixing. Electrical conductivity, electromagnetic shielding efficiency (EMI SE) in the X‐band frequency range (8–12.4 GHz), and melt flow index (MFI) results showed that ABS/CNT composites exhibit higher electrical conductivity and EMI SE, but lower MFI when compared to ABS/CB composites. The electrical conductivity of the binary composites showed an increase of around 16 orders of magnitude, when compared to neat ABS, for both fillers. Binary composites with 5 and 15 wt % of filler showed an EMI SE of, respectively, ?44 and ?83 dB for ABS/CNT, and ?9 and ?34 dB for ABS/CB. MFI for binary composites with 5 wt % were 15.45 and 0.55 g/10 min for CB and CNT, respectively. Hybrid composites ABS/CNT.CB with 3 wt % total filler and fraction 50:50 and 75:25 showed good correlation between EMI SE and MFI. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46546.     

Comparative study of EMI shielding effectiveness for carbon fiber pultruded polypropylene/poly(lactic acid)/multiwall CNT composites prepared by injection molding versus screw extrusion

The electrical conductivity and electromagnetic interference (EMI) shielding effectiveness of the composites of polypropylene/poly(lactic acid) (PP/PLA) (70/30, wt %) with single filler of multiwall carbon nanotube (CNT) or hybrid fillers of nickel‐coated carbon fiber (CF) and CNT were investigated. For the single filler composite, higher electrical conductivity was observed when the PP‐g‐maleic anhydride was added as a compatibilizer between the PP and PLA. For the composite of the PP/PLA (70/30)/CF (20 phr)/CNT (5 phr), the composite prepared by injection molding observed a higher EMI shielding effectiveness of 50.5 dB than the composite prepared by screw extrusion (32.3 dB), demonstrating an EMI shielding effectiveness increase of 49.8%. The higher values in EMI shielding effectiveness and electrical conductivity of the PP/PLA/CF (20 phr)/CNT (5 phr) composite seemed mainly because of the increased CF length when the composites were prepared using injection molding machine, compared with the composites prepared by screw extrusion. This result suggests that the fiber length of the conductive filler is an important factor in obtaining higher values of electrical conductivity and EMI shielding effectiveness of the PP/PLA/CF/CNT composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45222.     

Flexible poly(styrene-b-(ethylene-co-butylene)-b-styrene) nanocomposites for electromagnetic interference shielding

In this report, multiwalled carbon nanotubes (CNT) embedded poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) microspheres (CNT/SEBS) were prepared by solvent evaporation method. Reduced graphene oxide (rGO) nanosheets were used to cover the surface of CNT/SEBS microspheres. The CNT/SEBS/rGO nanocomposites with special segregated conductive network were fabricated by hot pressing these as-prepared complex microspheres. The morphology, electrical percolation threshold, electrical conductivity, and electromagnetic interference (EMI) shielding effectiveness (SE) of CNT/SEBS/rGO composites were characterized. The shielding mechanisms were discussed in detail. Analysis of electrical conductive performance shows that the electrical percolation threshold of rGO is 0.22 vol %. Results of EMI shielding test confirmed the synergistic effect between CNT and rGO. The EMI SE of the composite filled by 2.1 vol % CNT and 3.35 vol % rGO can achieve 26 dB in 8.2− 12.4 GHz (X band), which exceeds the basic requirement for commercial application (20 dB). Its reflectance coefficient (19–41%) indicates that the most part of incident electromagnetic (EM) wave energy is attenuated through absorption mechanism. This kind of absorptive EMI shielding material can be applied without serious secondary EM radiation pollution problems. The effects of filler content, molding temperature on EMI SE, and shielding mechanism were also investigated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48542.     

Electrical conductivity and EMI shielding effectiveness of polyurethane foam–conductive filler composites

The morphological, electrical, and thermal properties of polyurethane foam (PUF)/single conductive filler composites and PUF/hybrid conductive filler composites were investigated. For the PUF/single conductive filler composites, the PUF/nickel‐coated carbon fiber (NCCF) composite showed higher electrical conductivity and electromagnetic interference shielding effectiveness (EMI SE) than did the PUF/multiwall carbon nanotube (MWCNT) and PUF/graphite composites; therefore, NCCF is the most effective filler among those tested in this study. For the PUF/hybrid conductive fillers PUF/NCCF (3.0 php)/MWCNT (3.0 php) composites, the values of electrical conductivity and EMI SE were determined to be 0.171 S/cm and 24.7 dB (decibel), respectively, which were the highest among the fillers investigated in this study. NCCF and MWCNT were the most effective primary and secondary fillers, and they had a synergistic effect on the electrical conductivity and EMI SE of the PUF/NCCF/MWCNT composites. From the results of thermal conductivity and cell size of the PUF/conductive filler composites, it is suggested that a reduction in cell size lowers the thermal conductivity of the PUF/conductive filler composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44373.     

Electrical conductivity and electromagnetic interference shielding effectiveness of carbon black/sisal fiber/polyamide/polypropylene composites

The effects of hybrid fillers on the electrical conductivity and electromagnetic interference (EMI) shielding effectiveness (SE) of polyamide 6 (PA6)/polypropylene (PP) immiscible polymer blends were investigated. Carbon black (CB) and steam exploded sisal fiber (SF) were used as fillers. CB was coated on the surface of SF, and this was exploded by water steam to form carbon black modified sisal fiber (CBMSF). CB/SF/PA6/PP composites were prepared by melt compounding, and its electromagnetic SE was tested in low‐frequency and high‐frequency ranges. We observed that SF greatly contributed to the effective decrease in the percolation threshold of CB in the PA6/PP matrix and adsorbed carbon particles to form a conductive network. Furthermore, an appropriate CB/SF ratio was important for achieving the best shielding performance. The results indicate that CBMSF was suitable for use as electronic conductive fillers and the CB/SF/PA6/PP composites could be used for the purpose of EMI shielding. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42801.     

Strong and Flexible Carbon Fiber Fabric Reinforced Thermoplastic Polyurethane Composites for High‐Performance EMI Shielding Applications

Electromagnetic shielding materials play a significant role in solving the increasing environmental problem of electromagnetic pollutions. The commonly used metal‐based electromagnetic materials suffer from high density, poor corrosion resistance, and high processing cost. Polymer composites exhibit unique combined properties of lightweight, good shock absorption, and corrosion resistance. In this study, a novel high angle sensitive composite is fabricated by combining carbon fiber (CF) fabric with thermoplastic polyurethane elastomer (TPU). The effect of stacking angle of CF fabric on EMI shielding performance of composite is studied. When the stacking angle of CF fabric changed, the electromagnetic interference (EMI) shielding effectiveness (SE) of CF fabric/TPU composite can reach a maximum of 73 dB, and the tensile strength can reach 168 MPa. In addition, the composite has anisotropic conductivity, which is conductive along the plane direction and nonconductive along the thickness direction. Moreover, the CF fabric/TPU composite manifests exceptional EMI‐SE/density/thickness value of 383 dB cm² g^?1, which is higher than most of current EMI shielding composites reported in literature. In summary, CF fabric/TPU composite is an excellent EMI shielding material that is lightweight, highly flexible, and mechanically robust, which can be applied to the field of aerospace and some intelligent electronic devices.     

Effects of carbon fiber modification with multiwall CNT on the electrical conductivity and EMI shielding effectiveness of polycarbonate/carbon fiber/CNT composites

The effect of carbon fiber (CF) modification with multiwall carbon nanotube (CNT) on the electrical, mechanical, and rheological properties of the polycarbonate (PC)/CF/CNT composite was investigated. The CF and multiwall CNT (MWCNT) were treated with sulfuric acid and nitric acid (3:1 wt %) mixture, to modify the CF with the CNT. For the PC with acid-treated CNT (a-CNT) modified acid-treated CF (a-CF) (PC/a-CF/a-CNT) composite, the electrical conductivity, and the electromagnetic interference shielding effectiveness (EMI SE) showed the highest values, compared with those of the PC/a-CF and PC/a-CF/CNT composites. The EMI SE of the PC/a-CF (10 wt %)/a-CNT (0.5 wt %) composite was found to be 26 (dB at the frequency of 10.0 GHz, and the EMI SE was increased by 91.2%, compared to that of the PC/a-CF composite at the same amount of total filler content. Among the composites studied in this work, the PC/a-CF/a-CNT composite also showed the highest values of relative permittivity (ε_r) and dielectric loss factor. The above results suggest that the CF modification with the a-CNT significantly affected the electrical conductivity and EMI SE of the composite, and the hybrid fillers of the a-CNT and a-CF resulted in good electrical pathways in the PC/a-CF/a-CNT composite. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47302.     

Effects of filler geometry on internal structure and physical properties of polycarbonate composites prepared with various carbon fillers

BACKGROUND: The effects of filler geometry are important for understanding the internal structure and physical properties of polymer composites. To investigate the effects of filler geometry on electrical conductivity as well as morphological and rheological properties, three types of polycarbonate (PC) composites were prepared by melt compounding with a twin‐screw extruder. RESULTS: The electrical conductivity of PC/carbon black (CB) and PC/graphite (carbon) nanofibre (CNF) composites did not show a percolation threshold through the entire filler loading ranges. However, PC‐blend‐carbon nanotube (CNT) composites showed a percolation electrical threshold for a filler loading of 1.0 to 3.0 wt% and their maximum electrical conductivity approached 10^?3 S m^?1. PC‐blend‐CB and PC‐blend‐CNF composites showed Newtonian behaviour like pure PC matrix, but PC‐blend‐CNT composites showed yield stress as well as increased storage modulus and strong shear thinning behaviour at low angular frequency and shear rate due to strong interactions generated between CNT–CNT particles as well as PC molecules and CNT particles on the nanometre scale. CONCLUSIONS: The electrical conductivity of the PC composites with different carbon constituents was well explained by the continuous network structure formed between filler particles. The network structure was confirmed by the good dispersion of fillers as well as by the yield stress and solid‐like behaviour observed in steady and dynamic shear flows. Copyright © 2009 Society of Chemical Industry     

Study on the structure and properties of conductive silicone rubber filled with nickel‐coated graphite

In this study, the conductive silicone rubber composites filled with nickel‐coated graphite (NCG) have been prepared, and their morphology structure, electrical conductivity, electromagnetic interference shielding efficiency (EMI SE), and mechanical properties have been investigated with reference to the NCG filler loading. The mechanical strength of NCG particle was poor that it can be easily ground into smaller particle during the mixing process if the shear force during mixing is large enough. The electrical conductivity of the composites existed an obvious threshold value with the variation of the loading amount of the conductive filler. EMI SE of the composites increases with the decrease of the volume electrical resistivity. The Payne effect can be used to characterize the intensity of the three‐dimensional conductive network structure in silicone rubber matrix, and the difference of storage modulus in the low and high shear strain has good linear correlation with the electrical conductivity. So, the electrical conductivity and EMI SE can be estimated by means of the difference of storage modulus obtained from rubber process analysis test. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electrically conductive composites of polyurethane derived from castor oil with polypyrrole‐coated peach palm fibers

Electrically conducting fibers were prepared through in situ oxidative polymerization of pyrrole (Py) in the presence of peach palm fibers (PPF) using iron (III) chloride hexahydrate (FeCl₃·6H₂O) as oxidant. The polypyrrole (PPy) coated PPF displayed a PPy layer on the fibers surface, which was responsible for an electrical conductivity of (2.2 ± 0.3) × 10⁻¹ S cm⁻¹, similar to the neat PPy. Electrically conductive composites were prepared by dispersing various amounts of PPy‐coated PPF in a polyurethane matrix derived from castor oil. The polyurethane/PPy‐coated PPF composites (PU/PPF–PPy) exhibited an electrical conductivity higher than PU/PPy blends with similar filler content. This behavior is attributed to the higher aspect ratio of PPF–PPy when compared with PPy particles, inducing a denser conductive network formation in the PU matrix. Electromagnetic interference shielding effectiveness (EMI SE) value in the X‐band (8.2–12.4 GHz) found for PU/PPF–PPy composites containing 25 wt% of PPF–PPy were in the range −12 dB, which corresponds to 93.2% of attenuation, indicating that these composites are promising candidates for EMI shielding applications. POLYM. COMPOS., 38:2146–2155, 2017. © 2015 Society of Plastics Engineers     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

ASA/graphite/carbon black composites with improved EMI SE,conductivity and heat resistance properties

Composites, comprised of acrylonitrile styrene acrylate copolymer (ASA)/graphite (GR) with high electromagnetic interference shielding effectiveness (EMI SE), were fabricated by the introduction of carbon black (CB). The effects of CB on properties such as EMI SE, morphology, heat resistance, rheological and mechanical performance of the composites were characterized using a scanning electron microscope (SEM), rotational rheometer, electromagnetic shielding measuring instruments. The graphite and carbon black exhibited positive synergistic action, which promoted the complete formation of conductive networks in ASA matrix. The EMI SE and electrical conductivity of the ASA/GR/CB composites increased with higher CB loadings. In the frequency range of 30–3000 MHz, the maximum EMI SE of ASA composites with 50 % fillers reached 40 dB, but with 40 % fillers this property reached its maximum value of 50 dB. The flexural strength of ASA/GR/CB composites started to decline as CB loading exceeded 5 %. The heat resistance of the composites was improved due to the addition of CB. In this respect, the vicar softening temperature (VST) of the composites with 40 % fillers increased from 115.1 to 132.7 °C, and the VST of the composites with 50 % fillers was elevated from 125.4 to 138.9 °C.     

A Unique Double Percolated Polymer Composite for Highly Efficient Electromagnetic Interference Shielding

This study has developed a carbon nanotube (CNT)/ethylene vinyl acetate (EVA)/ultrahigh molecular weight polyethylene (UHMWPE) composite with a unique double percolated conductive structure, in which only 20 wt% of CNT enriched EVA is needed to form a continuous conductive network. Compared with conventional double percolated conductive polymer composites (CPCs) which require filler‐enriched polymer content up to 50 wt%, the low CNT/EVA content gives rise to an unprecedentedly increased effective CNT concentration in the CNT/EVA/UHMWPE composite. The double percolated composite exhibits electrical conductivity comparable to that obtained in CNT‐loaded single EVA composite with five times of CNT content. Only 7.0 wt% CNT gives the composite an electromagnetic interference (EMI) shielding effectiveness of 57.4 dB, much higher than that of mostly reported CNT and graphene based CPCs. Absorption is demonstrated to be the primary shielding mechanism due to the numerous interfaces between UHMWPE domains and CNT/EVA layers facilitating multiple reflection, scattering, and absorption of the incident microwaves. The construction of unique double percolated structure in this work provides a promising strategy for developing cost‐effective and high‐performance CPCs for use as efficient EMI shielding materials.

     

5‐Sulfoisophthalic acid monolithium salt doped polypyrrole/multiwalled carbon nanotubes composites for EMI shielding application in X‐band (8.2–12.4 GHz)

This article describes the synthesis and characterization of highly conductive polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites prepared by in situ polymerization of pyrrole using 5‐sulfoisophthalic acid monolithium salt [lithio sulfoisophthalic acid (LiSiPA)] as dopant and ferric chloride as oxidant. Several samples were prepared by varying the amounts of MWCNTs ranging from 1 to 5 wt %. Scanning electron microscope and transmission electron microscope images clearly show a thick coating of PPy on surface of MWCNTs. The electrical conductivity of PPy increased with increasing amount of MWCNTs and maximum conductivity observed was 52 S/cm at a loading of 5 wt % of MWCNTs. Pure PPy prepared under similar conditions had a conductivity of 25 S/cm. Electromagnetic interference (EMI) shielding effectiveness (SE) also showed a similar trend and average EMI shielding of ?108 dB (3 mm) was observed for sample having 5 wt % MWCNT in the frequency range of 8.2–12.4 GHz (X‐band). The light weight and absorption dominated total SE of ?93 to ?108 dB of these composites indicate the usefulness of these materials for microwave shielding. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45370.     

Effects of multiple carbon fillers on the rheology of polycarbonate‐based composites

Adding conductive carbon fillers to insulating thermoplastic polymers increases the electrical conductivity of the resulting composite, which could allow them to be used in electrostatic dissipative and semiconductive applications. Adding fillers often increases viscosity, which can make the material more difficult to process. In this study, three different carbon fillers [carbon black (CB), carbon nanotubes (CNT), and exfoliated graphite nanoplatelets (GNP)] were studied via three different combinations of two different fillers (CB/CNT, CB/GNP, and CNT/GNP). These filler combinations were studied via three 3² factorial designs, which considered the following loading levels: CB: 0, 2, and 5 wt%; CNT: 0, 1, and 5 wt%; and GNP: 0, 2, and 5 wt%. These composites were compounded, injection molded, and tested for electrical conductivity and steady shear viscosity. CB and GNP exhibited classic filler behavior, increasing the composite viscosity with increased filler loading. CNT acted differently, lowering the composite viscosity with increased filler loading. When CB and GNP were combined, the viscosity increase was additive. When CNT was combined with either CB or GNP, the resultant composite had a lower viscosity than the corresponding single filler composite with equivalent loadings of CB or GNP. This viscosity lowering effect of CNT, even at loadings as low as 1 wt%, allows for increased filler loadings of CB or GNP with little impact on processability. Five different formulations (four containing two filler combinations) could be used for electrostatic dissipative applications and seven different formulations (six containing two filler combinations) may be used for semiconductive applications. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Electromagnetic interference shielding effectiveness of ethylene vinyl acetate based conductive composites containing carbon fillers

Conductive polymeric based composites were derived from ethylene vinyl acetate rubber filled with Vulcan XC‐72, short carbon fiber (SCF), and their blends. The electromagnetic interference (EMI) shielding effectiveness (SE), return loss, and reflection coefficient were studied. The measurements of the SE of the composites were carried out in two different frequency ranges of 100–2000 MHz and 8–12 GHz (X band). It was observed that the SE of the composites was frequency dependent and it increased with increasing frequency. The increasing of filler loading also enhanced the SE of the composites. The 100% SCF filled composites showed a higher SE compared to that of the filler blend or purely carbon black filled composites. The correlation between the SE and bulk conductivity of various composites was also discussed. The compromise between EMI SE, electrical conductivity, and mechanical properties was obtained when the composites contained both types of filler like particulate carbon black and SCF. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1601–1608, 2001     

Poly(vinylidene fluoride)/thermoplastic polyurethane flexible and 3D printable conductive composites

This work focus on the development of polymeric blends to produce multifunctional materials for 3D printing with enhanced electrical and mechanical properties. In this context, flexible and highly conductive materials comprising poly(vinylidene fluoride)/thermoplastic polyurethane (PVDF/TPU) filled with carbon black-polypyrrole (CB-PPy) were prepared by compression molding, filament extrusion and fused filament fabrication. In order to achieve an optimal compromise between electrical conductivity, mechanical properties and printability, blends composition was optimized and different CB-PPy content were added. Overall, the electrical conductivities of PVDF/TPU 50/50 vol% co-continuous blend were higher than those found for PVDF/TPU 50/50 wt% (i.e., 38/62 vol%) composites at same filler content. PVDF/TPU/CB-PPy 3D printed samples with 6.77 vol% filler fraction presented electrical conductivity of 4.14 S m⁻¹ and elastic modulus, elongation at break and maximum tensile stress of 0.43 GPa, 10.3% and 10.0 MPa, respectively. These results highlight that PVDF/TPU/CB-PPy composites are promising materials for technological applications.     

Electrical conductivity modeling of carbon black/polycarbonate,carbon nanotube/polycarbonate,and exfoliated graphite nanoplatelet/polycarbonate composites

Adding conductive carbon fillers to electrically insulating thermoplastic polymers increases the resulting composite's electrical conductivity, which would enable them to be used in electrostatic dissipative and semiconductive applications. In this study, varying amounts of carbon black (CB: 2 to 10 wt %), multiwalled carbon nanotubes (CNT: 0.5 to 8 wt %), or exfoliated graphite nanoplatelets (GNP: 2 to 15 wt %) were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (EC = 1/electrical resistivity). The percolation threshold was ～ 1.2 vol % CNT, ～ 2.4 vol % CB, and ～ 4.6 vol % GNP. In addition, three EC models (Mamunya, additive, and general effective media) were developed for the CB/PC, CNT/PC, and GNP/PC composites. The general effective media (GEM) model showed the best agreement with the experimental results over the entire range of filler concentrations (above and below the percolation threshold) for all three composite systems. In addition, the GEM model can be easily adapted for composites containing combinations of different conductive fillers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Perpendicular and In‐Plane Conductivity of Poly(methyl methacrylate) Composite Films Filled with Carbon‐Based Fillers Prepared from Solution Casting Process

In this study, poly(methyl methacrylate) (PMMA)/carbon black (CB), PMMA/carbon fiber (CF), and PMMA/carbon nanotube (CNT) conductive composite films with different filler concentrations are prepared using the solution casting technique. Both perpendicular and in‐plane direction conductivity of all the binary composite films are investigated, percolation thresholds (?_c) of both directions of PMMA/CB, PMMA/CF, and PMMA/CNT composite films are investigated and the experimental data are fitted using McLachlan’s equation. For all the three investigated films, the perpendicular ?_c,⊥ and in‐plane ?_c,∥ with different fillers show totally different behaviors. Pristine CB, CF, and CNT as well as PMMA/CB, PMMA/CF, and PMMA/CNT composite films are discussed. The gravity effect of the fillers is found to be most significant in the PMMA/CB system. A schematic diagram of PMMA composite films with CB, CF, and CNT as filler prepared from solution casting process is presented to explain the distribution gradient of the fillers in the perpendicular direction of the film after solution casting. A power law behavior is revealed for different filler types (CB, CF, CNT) correlating the exponent t for McLachlan’s equation and corresponding ?_c for in‐plane and perpendicular directions.     

Modification of sisal fiber by in situ coating steam explosion and electromagnetic interference shielding effectiveness of sisal fiber/PP composites

The technology of steam explosion was adopted to modify sisal fiber (SF) material and two different carbon particles, expanded graphite and conductive carbon black (CCB), were in situ coated on the surface of SF during steam explosion process. The DC conductivity and electromagnetic interference shielding effectiveness (SE) of the modified SF/polypropylene (PP) composites were studied and the measurement of electromagnetic interference (EMI) SE was conducted in two frequency ranges of 400–1,000 MHz and 1–18 GHz. The experimental results showed that this novel coating technology could improve the SE of the modified SF/PP composites significantly, which has a strong dependence on the loadings of the expanded graphite modified sisal fiber (SF‐EG) and conductive carbon black modified sisal fiber (SF‐CCB). When the loadings of SF‐EG and SF‐CCB reached 50 wt%, the maximum values of the SE were 33 dB and 51 dB, respectively. For the modified SF/PP composites, the experimental EMI SE values are in good correlation with the theoretical calculation values in far field of electromagnetic radiation. POLYM. COMPOS., 35:1038–1043, 2014. © 2013 Society of Plastics Engineers