Release of salicylic acid through poly(vinyl alcohol)/poly(vinyl pyrrolidone) and poly(vinyl alcohol‐g‐N‐vinyl‐2‐pyrrolidone) membranes

A controlled release profile of salicylic acid (SA) for transdermal administration has been developed. Poly (vinyl alcohol) (PVA) and Poly(vinyl alcohol)/Poly(vinyl pyrrolidone) (PVP) blended preparations were used to prepare the membranes by solvent‐casting technique. The release of the drug from the membranes was evaluated at in vitro conditions. The effects of PVA/PVP (v/v) ratio, pH, SA concentration and temperature were investigated. 60/40 (v/v) PVA/PVP ratio was found to be the best ratio for the SA release. Increase in pH and temperature was observed to increase the transport of SA. Instead of blending PVA with PVP, N‐Vinyl‐2‐pyrrolidone (VP) was grafted onto the PVA and the delivery performance for SA was compared with that of the blended PVA/PVP membranes. Grafted membranes gave higher transport percentages than the blended membranes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1244–1253, 2006     

Preparation of poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) microspheres

Crosslinked poly(vinyl alcohol) (CPVA) microspheres were first prepared via the suspension polymerization of vinyl acetate and the alcoholysis of poly(vinyl acetate). Afterwards, a two‐step method involving graft polymerization and Hofmann degradation was used to prepare functional poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) (PVAm–CPVA) microspheres, onto which poly(vinyl amine) (PVAm) macromolecules were grafted. The graft polymerization of acrylamide (AM) on CPVA microspheres was performed with cerium salt as the initiator in an acidic aqueous medium, resulting in polyacrylamide (PAM)‐grafted CPVA microspheres. Subsequently, the grafted PAM was transformed into PVAm via the Hofmann degradation reaction, and PVAm–CPVA microspheres were prepared. The effects of the main factors on the graft polymerization and Hofmann degradation were examined, and the reaction mechanisms were researched in depth. The experimental results showed that for the graft polymerization of AM on CPVA microspheres initiated by cerium salt, the acid concentration and the amount of cerium salt affected the grafting degree of PAM greatly. For the Hofmann degradation reaction of the grafted PAM, the amination degree of PVAm–CPVA microspheres was obviously affected by the amount of sodium hypochlorite in the presence of sodium hydroxide. The preliminary adsorption tests showed that PVAm–CPVA microspheres were multifunctional and had strong adsorption ability for Fe(III) ions by chelation action and for chromate ions (CrO) by strong electrostatic interactions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Transient currents in poly(vinyl alcohol)–poly(vinyl pyrrolidone) polymer blend films

Transient currents (charging and discharging currents) in poly(vinyl alcohol) (PVA)–poly(vinyl pyrrolidone) (PVP) polymer blend films were measured over the temperature range 30–150°C at field strengths of 2.32–23.2 × 10⁶ Vm^?1. Polymer films were prepared by the isothermal immersion technique. Activation energies were evaluated from quasi-steady-state currents. A single relaxation peak was observed both from isochronal currents and low frequency dielectric relaxation. Activation energies evaluated from these two methods are found to be in fairly good agreement. The polarization is considered to be due to space charge origin along with some contribution from dipolar groups. The maximum loss was observed in Sample I (PVA: PVP = 25:75), suggesting maximum heterogeneity in this blend ratio.     

Adsorption of Cr(VI) ions onto poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole)

Poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole) [poly(EGDMA‐VTAZ)] beads (average diameter = 150–200 μm) were prepared by copolymerizing ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). Poly(EGDMA‐VTAZ) beads were characterized by swelling studies and scanning electron microscope (SEM). The adsorption of Cr(VI) from solutions was carried at different contact times, Cr(VI) concentrations, pH, and temperatures. High adsorption rates were achieved in about 240 min. The amount of Cr(VI) adsorbed increased with increasing concentration and decreasing pH and temperature. The intraparticle diffusion rate constants at various temperatures were calculated. Adsorption isotherms of Cr(VI) onto poly(EGDMA‐VTAZ) have been determined and correlated with common isotherm equations such as Langmuir and Freundlich isotherm models. The Langmuir isotherm model appeared to fit the isotherm data better than the Freundlich isotherm model. The pseudo first‐order kinetic model was used to describe the kinetic data. The study of temperature effect was quantified by calculating various thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy changes. The dimensionless separation factor (R_L) showed that the adsorption of metal ions onto poly(EGDMA‐VTAZ) was favorable. It was seen that values of distribution coefficient (K_D) decreasing with Cr(VI) concentration in solution at equilibrium (C_e) indicated that the occupation of activate surface sites of adsorbent increased with Cr(VI). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Coating of cotton yarn with poly(vinyl alcohol) and poly(N‐vinyl‐2‐pyrrolidone) crosslinked via ultraviolet radiation

The coating of cotton fiber is used in the textile industry to increase the mechanical resistance of the yarn and their resistance to vibration, friction, impact, and elongation, which are some of the forces to which the yarn is subjected during the weaving process. The main objective of this study was to investigate the use of synthetic hydrophilic polymers, poly(vinyl alcohol) (PVA), and poly(N‐vinyl‐2‐pyrrolidone) (PVP) to coat 100% cotton textile fiber, with the aim of giving the fiber temporary mechanical resistance. For the fixation of the polymer on the fiber, UV‐C radiation was used as the crosslinking process. The influence of the crosslinking process was determined through tensile testing of the coated fibers. The results indicated that UV‐C radiation increased the mechanical resistance of the yarn coated with PVP by up to 44% and the yarn coated with PVA by up to 67% compared with the pure cotton yarn, that is, without polymeric coating and crosslinking. This study is of great relevance, and it is important to consider that UV‐C radiation dispenses with the use of chemical substances and prevents the generation of toxic waste at the end of the process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Pervaporation separation of water–ethanol mixtures using metal‐ion‐exchanged poly(vinyl alcohol) (PVA)/sulfosuccinic acid (SSA) membranes

Poly(vinyl alcohol)/sulfosuccinic acid (PVA/SSA) membranes in the hydrogen form were converted to monovalent metal ion forms Li⁺, Na⁺, and K⁺. The effect of exchange with metal ions was investigated by measuring the swelling of water–ethanol (10/90) mixtures at 30 °C and by the pervaporative dehydration performance test for aqueous ethanol solutions with various ethanol concentrations at 30, 40, and 50 °C. In addition, electron spectroscopy for chemical analysis (ESCA) analysis was carried out to study the quantity of metal ions in membranes. From the ESCA analysis, the lithium ion quantity in the resulting membranes is greater than that of any other metal ions in question because of the easy diffusion of a smaller metal ion into the membrane matrix. The swelling ratio was in the following order: PVA/SSA‐Li⁺ > PVA/SSA‐Na⁺ > PVA/SSA‐K⁺ membranes. For pervaporation, the PVA/SSA‐Na⁺ membrane showed the lowest flux and highest separation factor for all aqueous ethanol solutions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1867–1873, 2002     

Synthesis and characterization of poly(ethylene glycol dimethacrylate–1‐vinyl‐1,2,4‐triazole) copolymer beads for heavy‐metal removal

We prepared poly(ethylene glycol dimethacrylate–1‐vinyl‐1,2,4‐triazole) [poly(EGDMA–VTAZ)] beads (average diameter = 150–200 μm) by copolymerizing ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). The copolymer composition was characterized by elemental analysis and found to contain five EGDMA monomer units for each VTAZ monomer unit. The poly(EGDMA–VTAZ) beads had a specific surface area of 65.8 m²/g. Poly(EGDMA–VTAZ) beads were characterized by Fourier transform infrared spectroscopy, elemental analysis, surface area measurements, swelling studies, and scanning electron microscopy. Poly(EGDMA–VTAZ) beads with a swelling ratio of 84% were used for the heavy‐metal removal studies. The adsorption capacities of the beads for Cd(II), Hg(II), and Pb(II) were investigated in aqueous media containing different amounts of these ions (5–750 mg/L) and at different pH values (3.0–7.0). The maximum adsorption capacities of the poly(EGDMA–VTAZ) beads were 85.7 mg/g (0.76 mmol/g) for Cd(II), 134.9 mg/g (0.65 mmol/g) for Pb(II), and 186.5 mg/g (0.93 mmol/g) for Hg(II). The affinity order toward triazole groups on a molar basis was observed as follows: Hg(II) > Cd(II) > Pb(II). pH significantly affected the adsorption capacity of the VTAZ‐incorporated beads. The equilibrium data were well fitted to the Redlich–Peterson isotherm. Consideration of the kinetic data suggested that chemisorption processes could have been the rate‐limiting step in the adsorption process. Regeneration of the chelating‐beads was easily performed with 0.1M HNO₃. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4276–4283, 2006     

Permeation characteristics of poly(vinyl alcohol)–poly(vinyl acetate) composite porous membranes

Poly(vinyl alcohol) (PVAc) composite porous membrane has been prepared from PVAc latex film by extraction with acetone. The PVAc latex was prepared by emulsion polymerization of vinyl acetate in the presence of PVA, employing the hydrogen peroxide–tartaric acid systemm as an initiator. The extraction degree of PVAc could be controlled in a wide range by changing the addition method of the initiator, and, acoordingly, PVA–PVAc omposite porous membranes which had variosu void volumes were obtained. The maximum void volume attained was ca. 90%. Permation characteristics of organic solvents wre investigated on the membranes whose extraction degrees were 95.6% and 80.7%. Thge feeds were benzene, n-hexane, cyclohexane, and their mixtures. neither swelling nor shrinkage in tje appearance size of the while benzene hardly permeated even at 20 kg/cm². The grafted PVAc in the mebrane was removed or converted into grafted PVA by treatment with sodium methylate, and then the depression of benzene permeation was lost. The grafted PVAc was suggested to be localizd on the cell wall and was found to function as a valve which closes with nenzene or a good solvent for PVAc and opens with n-haxane or a poor solvent for PVAc.     

Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and application of cotton‐based chelate fibers grafted with poly(1‐vinyl‐1,2,4‐triazole) side chains

Cotton‐based chelate fibers grafted with poly(1‐vinyl‐1,2,4‐triazole) (PVTAZ) side chains were synthesized facilely by ozone‐induced graft polymerization of 1‐vinyl‐1,2,4‐triazole (VTAZ) monomer onto cotton fibers. The synthesis conditions were optimized to improve the yield and mechanical strength of the products. The obtained cotton‐g‐PVTAZ fibers were characterized and evaluated for batch adsorption of heavy metal ions from aqueous solutions. The maximum adsorption capacity of Ag(I), Pb(II), and Cu(II) on the fibers at pH 6.8 was 522, 330, and 184 mg/g, respectively. At 30% graft yield, the Young's modulus of cotton fiber increased about 26.5%, and its adsorption capacities of Ag(I), Pb(II), and Cu(II) increased about 2.6, 1.9, and 1.4 times, respectively. After washed with 0.1 mol/L HNO₃ solutions, the adsorbed metal ions were eluted, and the regenerated cotton‐g‐PVTAZ fibers could be used repeatedly for water treatment. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41617.     

Properties of electrospun poly(vinyl alcohol) hydrogel nanofibers crosslinked with 1,2,3,4‐butanetetracarboxylic acid

ABSTRACT: Electrospun nanofibrous hydrogel membranes have been gaining significant importance due to the combination of unique physical properties of nanofibers and biocompatibility of hydrogels. Thus, they are considered as potential candidates for medical textile applications. This study deals with electrospinning of poly(vinyl alcohol) (PVA) hydrogel nanofibrous membranes. The chemical crosslinking of PVA with proportionate quantities of 1,2,3,4 butanetetracarboxylic acid (BTCA) was undertaken to form hydrogel structures. Cross‐linked membranes were characterized by scanning electron microscopy, FT‐IR and thermogravimetric analysis, water swelling, and durability tests. FT‐IR analysis demonstrated the formation of ester linkages between PVA and BTCA and thermogravimetric analysis showed that crosslinking improved the thermal stability of the nanofibrous structure. Furthermore, the results indicated that crosslinking with BTCA improved water stability of PVA membranes and the nanofibrous structure was preserved after water treatment. It is envisaged that use of BTCA as a cross‐linker to form hydrogel nanofibers could be a practical and a promising method for medical textile applications, especially for wound dressings given its nontoxicity and immiscibility with polymer solutions. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Dehydration of light oil by pervaporation using poly(vinyl alcohol)–poly(acrylic acid‐co‐maleic acid) membranes

A new blended membrane was prepared and tested by pervaporation of light oil, a mixture of five alcohols plus water. The blended membrane was synthesized by blending poly(vinyl alcohol) and poly(acrylic acid‐co‐maleic acid) sodium salt in the presence of sulfuric acid to dope the reaction. We tested several membranes in order to choose the adequate composition to have the best permselectivity. The PVA(60)–PAA‐co‐maleic acid(40) membrane was selected as it was found to be highly selective. Sorption experiments were performed using binary and ternary water–alcohol solutions. The influence of temperature and feed composition on the selectivity and flux in pervaporation was investigated for two different binary mixtures (water/ethanol, water/isobutanol) and one ternary system (water/ethanol/isobutanol). This membrane presents good permselective properties, high water flux, and good selectivity and can even be used for high‐water activities The performances of this new membrane were compared to those obtained with the PVA(90)–PAA(10) membrane synthesized recently: The fluxes observed for the water–ethanol separation were of the same order of magnitude but the selectivity was found to be much higher. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1709–1716, 2002     

Properties and pervaporation characteristics of chitosan–poly(N‐vinyl‐2‐pyrrolidone) blend membranes for MeOH–MTBE

Clear blends of chitosan with poly(N‐vinyl‐2‐pyrrolidone) (PVP) made from aqueous solutions appear to be miscible from visual appearance. Infrared (IR) spectra used to investigate the carbonyl—hydroxyl hydrogen bonding in the blends indicated compatibility of two polymers on a molecular level. The IR spectra were also used to determine the interaction change accessing with increasing temperature and indicated that a significant conformational change occurred. On the other hand, the blend membranes were evaluated for separation of methanol from methyl tert‐butyl ether. The influences of the membrane and the feed compositions were investigated. Methanol preferentially permeates through all the tested membranes, and the partial flux of methanol significantly increase with the poly(N‐vinyl‐2‐pyrrolidone) content increasing. The temperature dependence of pervaporation performance indicated that a significant conformational change occurred with increasing temperature. Combined with the IR results, the pervaporation properties are in agreement with characteristics of interaction between chain–chain within the blend membranes. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1452–1458, 1999     

Electrospinning of poly(vinyl alcohol) and poly(4‐styrenesulfonic acid) for fuel cell applications

Electrospun fibers of poly(vinyl alcohol) (PVA) and PVA/poly(4‐styrenesulfonic acid) (PSSA) were obtained. By varying PVA to PSSA weight ratios, various fiber sizes and shapes were observed. The fiber diameters ranged from 176 to 766 nm, and the largest fibers were obtained from 15 wt % aqueous PVA solution. The effect of solution viscosity on fiber morphology was discussed. The presence of PSSA in electrospun fibers was confirmed by Fourier Transform Infrared spectroscopy. The PVA fibers were thermally stable up to 250°C, and the PVA/PSSA fibers were stable up to approximately 150°C. The water stability of the fibers was improved by heat‐treatment at 120°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Poly(acrylic acid)–poly(vinyl alcohol) semi- and interpenetrating polymer network pervaporation membranes

A series of poly(acrylic acid) (PAA)–poly(vinyl alcoho) (PVA) semiinterpenetrating (SIPN) and interpenetrating (IPN) polymer network membranes were prepared by crosslinking PVA alone or by crosslinking both PVA and PAA. Glutaraldeyde and ethylene glycol were used as crosslinking agents for the PVA and PAA networks, respectively. The presence of PAA increases the permeability of the membranes while the presence of PVA improves their mechanical and film-forming properties. The mechanical properties of the membranes were investigated via tensile testing. These hydrophilic membranes are permselective to water from ethanol–water mixture and to ethanol from ethanol–benzene mixtures. The IPN membranes were employed for the former mixtures and the SPIN membranes for the latter, because the IPN ones provided too low permeation rates. The permeation rates and seperation factors were determined as functions of the IPN or SIPN composition, feed composition, and temperature. For the azeotropic ethanol–water mixture (95 wt % ethanol), the separation factor and permeation rate at 50°C of the PAA-PVA IPN membrane, containing 50 wt % PAA, were 50 and 260 g/m²h, respectively. For the ethanol–benzene mixture, the PAA–PVA SIPN membranes had separation factors between 1.4 and 1200 and permeation rates between 6 and 550 g/m²h, respectively, depending on the feed composition and temperature. © 1996 John Wiley & Sons, Inc.     

Release of diclofenac through gluteraldehyde crosslinked poly(vinyl alcohol)/poly(acrylic acid) alloy membranes

A controlled‐release preparation of diclofenac sodium for transdermal administration has been developed. Poly(vinyl alcohol) (PVA) and PVA/poly(acrylic acid) (PAA) alloy membranes were prepared from a solvent‐casting technique using different PVA/PAA (v/v) ratios. The release of the drug from the membrane was evaluated under in vitro conditions at pH 7.4. The delivery system provided linear release without time lag, burst effect, and boundary layer resistance. Effects of variables such as film thickness and PVA/PAA ratio on the permeation behavior of the polymeric membranes were discussed. The optimal PVA/PAA was determined as 50/50. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 72–77, 2004     

Synthesis and characterization of poly(vinyl alcohol)‐based membranes for direct methanol fuel cell

Membranes made of poly(vinyl alcohol) (PVA) and its ionic blends with sodium alginate (SA) and chitosan were synthesized and characterized for their ion-exchange capacity (IEC) and swelling index values to investigate their applicability in direct methanol fuel cells (DMFCs). These membranes were assessed for their intermolecular interactions, thermal stabilities, and mechanical strengths with Fourier transform infrared spectroscopy, X-ray diffraction methods, differential scanning calorimetry, thermogravimetric analysis, and tensile testing, respectively. Methanol permeability and proton conductivity were also estimated and compared to that of Nafion 117. In addition to being effective methanol barriers, the membranes had a considerably high IEC and thermal and mechanical stabilities. The addition of small amounts of anionic polymer was particularly instrumental in the significant reduction of methanol permeability from 8.1 × 10⁻⁸ cm²/s for PVA to 6.9 × 10⁻⁸ cm²/s for the PVA–SA blend, which rendered the blend more suitable for a DMFC. Low methanol permeability, excellent physicomechanical properties, and above all, cost effectiveness could make the use of these blends in DMFCs quite attractive. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1154–1163, 2005     

Poly(vinyl alcohol) and poly(vinyl amine) blend membranes for isopropanol dehydration

Blended membranes of hydrophilic polymers poly(vinyl alcohol) (PVA) and poly(vinyl amine) (PVAm) were prepared and crosslinked with glutaraldehyde. The prepared membranes were characterized using infrared (attenuated total reflection mode) spectroscopy, differential scanning calorimetry, X‐ray diffractometry, and scanning electron microscopy measurements. Pervaporation performances of the membranes were evaluated for the separation of water‐isopropanol (IPA) mixtures. As the PVAm content increased from PVAm0 to PVAm1.5, the flux through a 70 μm film increased from 0.023 to 0.10 kg/m² h at an IPA/water feed ratio of 85/15 at 30 °C. The driving force for permeation of water increased due to the temperature but it has no effect on IPA permeation. Activation energies for the permeation of IPA and water were calculated to be 17.11 and 12.46 kJ/mol, respectively. Controlling the thickness of the blend membrane could improve the permeation flux with only a marginal reduction in the separation factor. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45572.     

Pervaporation separation of isopropanol–water mixtures using mixed matrix blend membranes of poly(vinyl alcohol)/poly(vinyl pyrrolidone) loaded with phosphomolybdic acid

Mixed matrix membranes of poly(vinyl alcohol) and poly(vinyl pyrrilidone) blends were prepared by loading with phosphomolybdic acid (PMA) and their pervaporation (PV) properties were investigated for the PV separation of isopropanol. Membrane performance shown a dependence on the extent of PMA loading. The 4 wt % PMA‐loaded blend membrane had the highest separation factor of 29991, which declined considerably at higher loading. The flux of 4 wt % PMA‐loaded membrane was lower than that of nascent blend membrane. Feed water composition and temperature influenced the PV performance. Solubility selectivity was higher than diffusion selectivity. Degree of swelling was smaller after PMA loading exhibiting better separation ability. The PV results were analyzed using the Flory‐Huggins theory and sorption was dominated by Langmuir's mode. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011