Influence of mesophase–crystal transition on thermal and mechanical properties of stretched poly(L‐lactide)

The mesophase in the as‐stretched poly(L ‐lactide) (PLLA) exhibits low thermal stability and undergoes melting around T_g. As a consequence, without constraints as‐stretched PLLA can recover to its original (unstretched) length while being held above T_g. Upon constrained annealing at 70°C mesophase is transformed into highly oriented crystals, responsible for little free shrinkage and superior dimensional stability. At the same time, molecular orientation in the amorphous phase first decreases significantly due to thermodynamic relaxation, and then increases moderately with the advent of cold crystallization. It correlates well with the change of yield strength with respect to annealing time. POLYM. ENG. SCI., 53:2568–2572, 2013. © 2013 Society of Plastics Engineers     

Glass transition and mechanical properties of PLLA and PDLLA‐PGA copolymer blends

The change of the glass transition temperatures (T_g) in the blend of poly(L ‐lactic acid) (PLLA) and the copolymers of poly(D,L ‐lactic acid) and poly(glycolic acid) (PDLLA‐PGA) with different D,L ‐lactic acid and glycolic acid composition ratio (50 : 50, 65 : 35, and 75 : 25) was studied by DSC. Dynamic mechanical measurement and tensile testing were performed at various temperatures around T_g of the blend. In the blend of PLLA and PDLLA‐PGA50 (composition ratio of PDLLA and PGA 50 : 50), T_g decreased from that of PLLA (about 58°C) to that of PDLLA‐PGA50 (about 30°C). A single step decrease was observed in the DSC curve around T_g between the weight fraction of PLLA (W(PLLA)) 1.0 and 0.7 (about 52°C) but two‐step changes in the curve are observed between W(PLLA) = 0.6 and 0.3. The T_g change between that of PLLA and that of PDLLA‐PGA and the appearance of two T_gs suggest the existence of PLLA rich amorphous region and PDLLA‐PGA copolymer rich amorphous region in the blend. A single step decrease of E′ occurs at around T_g of the pure PLLA but the two‐step decrease was observed at W(PLLA) = 0.6 and 0.4, supporting the existence of the PLLA rich region and PDLLA‐PGA rich region. Tensile testing for various blends at elevated temperature showed that the extension without yielding occurred above T_g of the blend. Partial miscibility is suggested for PLLA and PDLLA‐PGA copolymer blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2164–2173, 2004     

Poly(para‐dioxanone)/poly(D,L‐lactide) blends compatibilized with poly(D,L‐lactide‐co‐para‐dioxanone)

The effect of poly(D ,L ‐lactide‐co‐para‐dioxanone) (PLADO) as the compatibilizer on the properties of the blend of poly(para‐dioxanone) (PPDO) and poly(D ,L ‐lactide) (PDLLA) has been investigated. The 80/20 PPDO/PDLLA blends containing from 1% to 10% of random copolymer PLADO were prepared by solution coprecipitation. The PLADO component played a very important role in determining morphology, thermal, mechanical, and hydrophilic properties of the blends. Addition of PLADO into the blends could enhance the compatibility between dispersed PDLLA phase and PPDO matrix; the boundary between the two phases became unclear and even the smallest holes were not detected. On the other hand, the position of the T_g was composition dependent; when 5% PLADO was added into blend, the T_g distance between PPDO and PDLLA was shortened. The blends with various contents of compatibilizer had better mechanical properties compared with simple PPDO/PDLLA binary polymer blend, and such characteristics further improved as adding 5% random copolymers. The maximum observed tensile strength was 29.05 MPa for the compatibilized PPDO/PDLLA blend with 5% PLADO, whereas tensile strength of the uncompatibilized PPDO/PDLLA blend was 14.03 MPa, which was the lowest tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004     

The role of polycarbonate molecular weight in the poly(L‐lactide) blends compatibilized with poly(butylene succinate‐co‐L‐lactate)

Poly(butylene succinate‐co‐L ‐lactate) (PBSL)–compatibilized poly(L ‐lactide) (PLLA) polymer blends with two commercial grades of polycarbonate (PC) were investigated. The capillary tests showed that the steady shear viscosity of high molecular weight PC (PC‐L) was 10 times higher than that of low molecular weight PC (PC‐AD) throughout the shear rate range under investigation. Morphologic examination revealed that the shape of the dispersed PC‐L phase in the as‐extruded blends was largely spherical, but the PC‐AD phase was more like a rod and elongated further during injection molding. Notched Izod impact strength (IS) of the unmodified PLLA/PC‐L blend was higher than that of PC‐AD blend. The IS of modified ternary blends increased with PBSL content because of enhanced phase interaction indicated from thermal and morphologic analysis. The PBSL modification also enhanced IS more significantly in PLLA/PC‐L than in PLLA/PC‐AD blends. On the contrary, the heat deflection temperature (HDT) of PLLA/PC‐L binary system was much lower than that of PLLA/PC‐AD. HDT of PBSL‐modified PLLA/PC‐AD blends dropped with increasing PBSL content, which is a ductile polymer. Thermal and dynamic mechanical analysis of the ternary blends showed that individual components were immiscible with distinct T_gs for PC and PLLA and distinct T_ms for PBSL and PLLA. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Effect of nucleating agents on the crystallization behavior and heat resistance of poly(l‐lactide)

Poly (l ‐lactide) (PLLA) blends with various nucleators were prepared by melt processing. The effect of different nucleators on the crystallization behavior and heat resistance as well as thermomechanical properties of PLLA was studied systematically by differential scanning calorimetry, X‐ray diffraction, heat deflection temperature tester, and dynamic mechanical analysis. It was found that poly(d ‐lactide), talcum powder (Talc), a multiamide compound (TMC‐328, abbreviated as TMC) can significantly improve the crystallization rate and crystallinity of PLLA, thus improving thermal–resistant property. The heat deflection temperature of nucleated PLLA can be as high as 150°C. The storage modulus of nucleated PLLA is higher than that of PLLA at the temperature above T_g of PLLA. Compared with other nucleating agents, TMC was much more efficient at enhancing the crystallization of PLLA and the PLLA containing TMC showed the best heat resistance. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42999.     

Plasticization of Poly‐L‐lactide with L‐lactide,D‐lactide,and D,L‐lactide monomers

Poly‐L ‐lactide (PLLA) is being widely considered for repair of damaged tissues, for controlled antibiotic release, and also as scaffolds for cultured cells. PLLA was blended with the lactide monomer in its two enantiomeric forms: D ‐lactide (D ‐la) and L ‐lactide (L ‐la) and with the cyclic dimmer D ,L ‐la, in order to enhance its flexibility and thereby overcome its inherent problem of brittleness. In this work, the crystallization, phase structure, and tensile properties of PLLA and PLLA plasticized with 5, 10, 15, and 20 wt% of D ‐la, L ‐la, and D ,L ‐la are explored. The three plasticizers used were effective in lowering the glass transition temperature (T_g) and the melting temperature (T_m) of PLLA, around 20°C for a plasticizer content of 20 wt%. The tensile strength and modulus of the blends decreased following the increasing content of plasticizers from approximately 58 MPa to values below 20 MPa, and from 1667 to 200 MPa, respectively. Aging the blends at storage ambient temperature revealed that the enhanced flexibility as well as the morphological stability was lost over time due to the migration of the plasticizer to the surface, this being less marked in the case of D ‐la as a result of interactions between the polymer and its enantiomeric monomer of complementary configuration. POLYM. ENG. SCI., 53:2073–2080, 2013. © 2013 Society of Plastics Engineers     

Ternary polymer blends based on poly(lactic acid): Effect of stereo‐regularity and molecular weight

The effects of stereo‐regularity and molecular weight of poly(lactic acid) (PLA) on ternary polymer blends was analyzed using optical clarity as the primary screening method. This enabled the ready identification of phase boundaries of optically clear and apparently miscible regions. Solvent‐mediated blends of amorphous poly(dl ‐lactide) (PDLLA) and semi‐crystalline poly(l ‐lactide) (PLLA) with various molecular weights from high to low, along with polycaprolactone (PCL) and cellulose acetate butyrate (CAB) were used in this study. The nature and extent of crystallinity of the blends was examined by X‐ray diffraction, which, in conjunction with differential scanning calorimetry, scanning electron microscopy, and Fourier transform infrared spectroscopy, provided information about the competition between polymer crystallization (self‐aggregating behavior) and intermixing of the macromolecules. Thus, allowing the primary physical cause of transparency loss to be identified. The results of the ternary blends optical clarity showed the position of the phase boundaries in PLLA/PCL/CAB and PDLLA/PCL/CAB blends are significantly affected by the stereo‐regularity and molecular weight of PLA. The PDLLA (amorphous) blend shows comparable regions of phase separation with high molecular weight and semi‐crystalline PLLA blends even though the molecular weight is much lower. The blends of the shorter chain PLLA1 tend to show more crystalline regions. The optical transparency, miscibility, and crystallinity of the blends are not only affected by the stereo‐regularity and molecular weight of PLA but also the crystallizable PCL, especially at high loading. These findings give useful information to the film‐packaging sector where good optical clarity is a critical performance requirement. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41780.     

Miscibility and phase structure of binary blends of polylactide and poly(vinylpyrrolidone)

The miscibility, crystallization behavior, and component interactions of two binary blends, poly(L ‐lactide) (L ‐PLA)/poly(vinylpyrrolidone) (PVP) and poly(D ,L ‐lactide) (DL ‐PLA)/PVP, were studied with differential scanning calorimetry and Fourier transform infrared (FTIR) spectroscopy. The composition‐dependent changes of the glass‐transition temperature (T_g) and degree of crystallinity (X_c) of the L ‐PLA phase indicated that L ‐PLA and PVP were immiscible over the composition range investigated. However, the sharp decrease of X_c with increasing PVP content in the second heating run demonstrated that the cold crystallization process of L ‐PLA was remarkably restricted by PVP. In DL ‐PLA/PVP blends, the existence of two series of isolated T_g's indicated that DL ‐PLA and PVP were phase‐separated, but evidence showed that there was some degree of interaction at the interface of the two phase, especially for the blends with low DL ‐PLA contents. FTIR measurements showed that there was no appreciable change in the spectra of L ‐PLA/PVP with respect to the coaddition of each component spectrum, implying the immiscibility of the two polymers. In contrast to L ‐PLA, the intermolecular interaction between DL ‐PLA and PVP was detected by FTIR; this was evidenced by the observation of a high‐frequency shift of the C?O stretching vibration band of PVP with increasing DL ‐PLA content, which suggested some degree of miscibility. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 973–979, 2003     

Thermal properties and miscibility of semi‐crystalline and amorphous PLA blends

The focus of this research is the study of the microstructures and miscibility at the interface between semi‐crystalline and amorphous PLAs [poly (l ‐lactic acid)(PLLA) with poly (l ,d ‐lactic acid)(PDLLA), respectively]. The blends are prepared through thermal processing (extrusion and hot‐pressing). To increase the area of interface between PDLLA and PLLA, the fibers from PLLA and PDLLA are used. Thermal and microstructures of the blends were studied by differential scanning calorimetry (DSC), polarized optical microscopy (POM), dynamic thermogravimetric analysis(DMA), small‐angle X‐ray diffraction(SAXS) and wide‐angle X‐ray diffraction (WAXD). The two PLAs are miscible in molten state. However, phase separation is detected after various thermal treatments, with PDLLA being excluded from the regions of interlamellar PLLA regions when PDLLA content is low, as determined from X‐ray diffraction studies. The compatibility between the two PLAs is not perfect in the molten state, since enthalpies of the various blends at T_g are lower than any pure PLA material. The semi‐crystalline PLLA fiber can recrystallize alone in the molten amorphous PDLLA, and a higher nuclei density is observed at the interface. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41205.     

Accelerated crystallization of poly(L‐lactide) by physical aging

The low‐temperature physical aging of amorphous poly(L ‐lactide) (PLLA) at 25–50°C below glass transition temperature (T_g) was carried out for 90 days. The physical aging significantly increased the T_g and glass transition enthalpy, but did not cause crystallization, regardless of aging temperature. The nonisothermal crystallization of PLLA during heating was accelerated only by physical aging at 50°C. These results indicate that the structure formed by physical aging only at 50°C induced the accelerated crystallization of PLLA during heating, whereas the structure formed by physical aging at 25 and 37°C had a negligible effect on the crystallization of PLLA during heating, except when the physical aging at 37°C was continued for the period as long as 90 days. The mechanism for the accelerated crystallization of PLLA by physical aging is discussed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of steric hindrance on hydrogen‐bonding interaction between polyesters and natural polyphenol catechin

The phase behaviors for the blends of poly(3‐hydroxypropionate) (PHP), poly(L ‐lactide) (PLLA), poly(D ‐lactide) (PDLA), and poly(D,L ‐lactide) (PDLLA) with catechin were investigated by differential scanning calorimetry. In PLLA/catechin, PDLA/catechin, and PDLLA/catechin blends, two glass transitions were detected when the catechin content was ≥40 wt %, whereas in PHP/catechin blends only one glass transition was observed over the whole range of blend compositions. The former and the latter results should reflect the inhomogeneous and the homogeneous nature of the blends, respectively, in the amorphous phase. These different phase behaviors should arise from the differences in the chemical structures between PHP and PLLA/PDLA/PDLLA, which dominates the strength and the number of intermolecular hydrogen‐bonding interactions between the ester carbonyl groups of polyesters and the phenol groups of catechin. As detected by FTIR spectroscopy, in comparison with PHP, the steric hindrance of side‐chain methyl groups of PLLA, PDLA, and PDLLA might restrain the formation of hydrogen bonds between their ester carbonyl groups and the phenol hydroxyl groups of catechin, even weakening the strength of such hydrogen bonds. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3565–3573, 2004     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Compatibility of liquid deproteinized natural rubber having epoxy group (LEDPNR)/poly (L‐lactide) blend

Reaction after mixing of liquid epoxidized natural rubber/poly(L ‐lactide) blend was performed to enhance the compatibility of the blend. The liquid epoxidized natural rubber was prepared by epoxidation of deproteinized natural rubber with peracetic acid in latex stage followed by depolymerization with peroxide and propanal. The resulting liquid deproteinized natural rubber having epoxy group (LEDPNR) was mixed with poly(L ‐lactide) (PLLA) to investigate the compatibility of the blend through differential scanning calorimetry, optical light microscopy, and NMR spectroscopy. After heating the blend at 473 K for 20 min, glass transition temperature (T_g) of LEDPNR in LEDPNR/PLLA blend increased from 251 to 259 K, while T_g and melting temperature (T_m) of PLLA decreased from 337 to 332 K and 450 to 445 K, respectively, suggesting that the compatibility of LEDPNR/ PLLA blend was enhanced by a reaction between the epoxy group of LEDPNR and the ester group of PLLA. The reaction was proved by high‐resolution solid‐state ¹³C NMR spectroscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and conformation effects of poly(phenylacetylene)s having chiral and racemic polylactide pendants

Chiral and racemic macromonomers with a polymerizable phenylacetylenyl end group (PA‐PLLA and PA‐PDLLA) were successfully synthesized through living ring‐opening polymerization of chiral and racemic monomers (L ‐lactide and DL ‐lactide), respectively. Then the homopolymerization of PA‐PLLA and PA‐PDLLA was successfully carried out to give poly(PA‐PLLA) and poly(PA‐PDLLA), respectively. Chiroptical properties, hydrodynamic radii and micromorphologies of poly(PA‐PLLA) and poly(PA‐PDLLA) were analyzed via circular dichroism, dynamic light scattering and atomic force microscopy (AFM), and the conformation of the polymers is discussed. The results indicate that poly(PA‐PLLA) induced Cotton effects with different intensities in various solvents, and its hydrodynamic radii and dispersity were also different in various solvents, while poly(PA‐PDLLA) induced no Cotton effects and its hydrodynamic radii and dispersity were approximately the same in various solvents. Furthermore, a helical conformation of poly(PA‐PLLA) and the random main chains of poly(PA‐PDLLA) were observed by AFM. Therefore, it is concluded that poly(PA‐PLLA) possesses a dynamic one‐handed helical conformation in various solvents due to chiral poly(L ‐lactide) pendants, while poly(PA‐PDLLA) possesses racemic main chains because of the racemic poly(DL ‐lactide) pendants. Copyright © 2012 Society of Chemical Industry     

Synthesis of star‐shaped poly(ε‐caprolactone)‐b‐poly(L‐lactide) copolymers: From star architectures to crystalline morphologies

Hexa‐armed star‐shaped poly(ε‐caprolactone)‐block‐poly(L ‐lactide) (6sPCL‐b‐PLLA) with dipentaerythritol core were synthesized by a two‐step ring‐opening polymerization. GPC and ¹H NMR data demonstrate that the polymerization courses are under control. The molecular weight of 6sPCLs and 6sPCL‐b‐PLLAs increases with increasing molar ratio of monomer to initiator, and the molecular weight distribution is in the range of 1.03–1.10. The investigation of the melting and crystallization demonstrated that the values of crystallization temperature (T_c), melting temperature (T_m), and the degree of crystallinity (X_c) of PLLA blocks are increased with the chain length increase of PLLA in the 6sPCL‐b‐PLLA copolymers. On the contrary, the crystallization of PCL blocks dominates when the chain length of PLLA is too short. According to the results of polarized optical micrographs, both the spherulitic growth rate (G) and the spherulitic morphology are affected by the macromolecular architecture and the length of the block chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility and phase structure of binary blends of poly(L‐lactide) and poly(vinyl alcohol)

Blend films of poly(L ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA) were obtained by evaporation of hexafluoroisopropanol solutions of both components. The component interaction, crystallization behavior, and miscibility of these blends were studied by solid‐state NMR and other conventional methods, such as Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WAXD). The existence of two series of isolated and constant glass‐transition temperatures (T_g's) independent of the blend composition indicates that PLLA and PVA are immiscible in the amorphous region. However, the DSC data still demonstrates that some degree of compatibility related to blend composition exists in both PLLA/atactic‐PVA (a‐PVA) and PLLA/syndiotactic‐PVA (s‐PVA) blend systems. Furthermore, the formation of interpolymer hydrogen bonding in the amorphous region, which is regarded as the driving force leading to some degree of component compatibility in these immiscible systems, is confirmed by FTIR and further analyzed by ¹³C solid‐state NMR analyses, especially for the blends with low PLLA contents. Although the crystallization kinetics of one component (especially PVA) were affected by another component, WAXD measurement shows that these blends still possess two isolated crystalline PLLA and PVA phases other than the so‐called cocrystalline phase. ¹³C solid‐state NMR analysis excludes the interpolymer hydrogen bonding in the crystalline region. The mechanical properties (tensile strength and elongation at break) of blend films are consistent with the immiscible but somewhat compatible nature of these blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 762–772, 2001     

Preparation and characterization of poly(L‐lactide) membranes prepared by γ‐radiation‐induced grafting of N‐vinyl pyrrolidone

A copolymer, poly(L ‐lactide)‐g‐poly(N‐vinyl pyrrolidone) (PLLA‐g‐PVP) was prepared with poly(L ‐lactide) (PLLA) and N‐vinyl pyrrolidone in the presence of methanol as a solvent by γ‐ray irradiation. The structure of PLLA‐g‐PVP was characterized by ¹H‐NMR and Fourier transform infrared spectroscopy. The PLLA‐g‐PVP graft ratio calculated by the percentage increase in weight increased with the increase of absorbed dose, and the percentage crystallinity of PLLA‐g‐PVP decreased with increasing graft ratio. The introduction of the poly(N‐vinyl pyrrolidone) chain into PLLA resulted in a decrease in the contact angle of PLLA‐g‐PVP with increasing graft ratio. In vitro degradation testing showed that PLLA‐g‐PVP had a higher degradation rate both in the weight‐loss test and molecular weight measurement because of a lower crystalline percentage and higher hydrophilicity compared to PLLA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization,morphology, and mechanical behavior of polylactide/poly(ε‐caprolactone) blends

Optically pure polylactides, poly(L ‐lactide) (PLLA) and poly(D ‐lactide) (PDLA), were blended across the range of compositions with poly(ε‐caprolactone) (PCL) to study their crystallization, morphology, and mechanical behavior. Differential scanning calorimetry and dynamic mechanical analysis (DMA) of the PLA/PCL blends showed two T_gs at positions close to the pure components revealing phase separation. However, a shift in the tan δ peak position by DMA from 64 to 57°C suggests a partial solubility of PCL in the PLA‐rich phase. Scanning electron microscopy reveals phase separation and a transition in the phase morphology from spherical to interconnected domains as the equimolar blend approaches from the outermost compositions. The spherulitic growth of both PLA and PCL in the blends was followed by polarized optical microscopy at 140 and 37°C. From tensile tests at speed of 50 mm/min Young's modulus values between 5.2 and 0.4 GPa, strength values between 56 and 12 MPa, and strain at break values between 1 and 400% were obtained varying the blend composition. The viscoelastic properties (E′ and tan δ) obtained at frequency of 1 Hz by DMA are discussed and are found consistent with composition, phase separation, and crystallization behavior of the blends. POLYM. ENG. SCI., 46:1299–1308, 2006. © 2006 Society of Plastics Engineers     

The effect of citrate ester plasticizers on the thermal and mechanical properties of poly(DL‐lactide)

Citrate esters triethyl citrate, tributyl citrate, and acetyl tributyl citrate were used as plasticizers for amorphous poly(D,L ‐lactide) (PDLLA). The resultant compositions were analyzed by means of differential scanning calorimetry (DSC), dynamic mechanical thermal analysis, and tensile testing to investigate the properties of the blends. Glass transition temperatures (T_gs) obtained by DSC were also compared to theoretically calculated T_gs. Increasing plasticizer content decreased the resultant T_g of the blend with plasticizer efficiency enhanced as the molecular weight of the citrate ester increased. However, in blends with high plasticizer content, a lack of miscibility also occurred with increased molecular weight. Theoretical results were comparable with those obtained experimentally at compositions, which were miscible. Increasing plasticizer content increased the ductility and decreased the strength of the polymer. The addition of 10 wt % plasticizer to PDLLA decreased tensile strength by over 50% with the deterioration larger at higher concentrations of plasticizer. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013