Electrospinning fabrication and characterization of poly(vinyl alcohol)/montmorillonite nanofiber mats

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanofiber mats have been fabricated by the electrospinning technique. The PVA/MMT nanofiber mats were characterized by X‐ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and mechanical measurements. The study showed that the introduction of MMT results in improvement in tensile strength, and thermal stability of the PVA matrix. XRD patterns and SEM micrographs suggest the coexistence of exfoliated MMT layers over the studied MMT contents. FTIR revealed that there might be possible interaction occurred between the MMT clay and PVA matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of poly(vinyl alcohol) nanofiber mats crosslinked with blocked isocyanate prepolymer

Poly(vinyl alcohol) (PVA) nanofibers crosslinked with blocked isocyanate prepolymer (BIP) were successfully prepared using the electrospinning process and subsequent thermal treatment. Fourier transform infrared spectroscopy and solid‐state ¹³C NMR spectroscopy demonstrated that chemical crosslinks between the hydroxyl group of PVA and the isocyanate group of BIP were formed. Thermogravimetric analysis and differential scanning calorimetry results indicated that when the BIP content was increased, the thermal stability of PVA/BIP nanofibers increased, and the crystallinity of PVA decreased. Field emission scanning electron microscopy was used to measure the average diameter (200–300 nm) of the electrospun PVA/BIP nanofibers. The water contact angles were 10.2° and 113° for the pristine PVA nanofibers and PVA nanofibers crosslinked with 8 wt% BIP, respectively. The tensile strength of the crosslinked PVA nanofibers was 53.7 MPa, which was seven times higher than that of pristine PVA. The improved tensile strength and water resistance of the crosslinked PVA/BIP nanofibers were due to a combination of increased crosslinking density and decrease in the number of hydroxyl groups on the surface of the PVA/BIP nanofibers. Copyright © 2010 Society of Chemical Industry     

On the electrospinning of poly(vinyl alcohol) nanofiber mats: A revisit

Electrospinning was used to fabricate mats of poly(vinyl alcohol) (PVA; M_w = 72,000 Da, degree of hydrolysis ≈ 97.5–99.5) nanofibers from PVA solutions in reverse osmotic water. The effects of solution concentration, applied electrical potential, sonication, and collection distance on morphological appearance and diameters of the as‐spun fiber mats as well as those of the individual fibers were carefully investigated mainly by scanning electron microscopy. The effect of the distance from the center of the as‐spun fiber mat on morphological appearance and diameters of the as‐spun fibers was also investigated. The mechanical integrity of some as‐spun PVA fiber mats was also investigated. At all concentrations and applied electrical potentials investigated, the average diameters of the as‐spun PVA fibers ranged between 85 and 647 nm. The use of sonication to prepare a PVA solution caused the viscosity of the solution to decrease; hence, the observed decrease in the average diameters of the as‐spun fibers and the average diameters of the as‐spun fibers were practically the same throughout the as‐spun fiber mat. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study of electrospinning of sodium alginate,blended solutions of sodium alginate/poly(vinyl alcohol) and sodium alginate/poly(ethylene oxide)

Alginate is an interesting natural biopolymer for many of its merits and good biological properties. This paper investigates the electrospinning of sodium alginate (NaAlg), NaAlg/PVA‐ and NaAlg/PEO‐ blended systems. It was found in this research that although NaAlg can easily be dissolved in water, the aqueous NaAlg solution could not be electrospun into ultrafine nanofibers. To overcome the poor electrospinnability of NaAlg solution, synthetic polymers such as PEO and PVA solutions were blended with NaAlg solution to improve its spinnability. The SEM images of electrospun nanofibers showed that the alginate (2%, w/v)–PVA (8%, w/v) blended system in the volume ratio of 70 : 30 and the alginate (2%, w/v)–PEO (8% w/v) blended system in the volume ratio of 50 : 50 could be electrospun into finest and uniform nanofibers with average diameters of 118.3 nm (diameter distribution, 75.8–204 nm) and 99.1 nm (diameter distribution, 71–122 nm), respectively. Rheological studies showed a strong dependence of spinnability and fiber morphology on solution viscosity and thus on the alginate‐to‐synthetic polymer (PVA or PEO) blend ratios. FTIR studies indicate that there are the hydrogen bonding interactions due to the ether oxygen of PEO (or the hydroxyl groups of PVA) and the hydroxyl groups of NaAlg. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Orientation of poly(vinyl alcohol) nanofiber and crystallites in non-woven electrospun nanofiber mats under uniaxial stretching

The development of macroscopic nanofiber orientation and microscopic crystallite and molecular chain orientation have been investigated during uniaxial stretching of electrospun poly(vinyl alcohol) (PVA) non-woven nanofiber mats. Scanning electron microscopy and stress-strain/small-angle X-ray scattering show that the macroscopic nanofiber orientation significantly increases during the initial stage of deformation, and approaches a plateau on the way of stretching. Detailed analyses of the stress-strain/wide-angle X-ray diffraction measurement and polarized Fourier transform infrared spectroscopy indicate that the microscopic crystallite and molecular chain orientation rapidly increase at the initial stage of stretching due to macroscopic nanofiber orientation. At higher deformation, the microscopic modes of orientation continuously develop as a result of the nanofiber stretching. The complicated deformation process of non-woven nanofiber mats is discussed in terms of macroscopic nanofiber orientation and the microscopic crystallite and molecular chain orientation.     

静电纺丝法纺制聚乳酸纳米纤维无纺毡

采用静电纺丝法制备了生物降解聚乳酸(PLLA)纳米纤维无纺毡。分析了纺丝液浓度、电压、接收距离、挤出速度等因素对纤维形态的影响。结果表明:纺丝液的浓度和挤出速度对纤维直径的影响较为明显,溶液挤出速度增大,所得纤维微孔含量及尺寸也增大;适当的电压和接收距离有利于收集无液滴纤维;随着纤维直径的减小,无纺毡的孔径呈减小趋势。在PLLA质量分数为5．7％、挤出速度0．8 mL／h、接受距离 15．5 cm、电压8 kV的静电纺丝条件下,可制备纤维直径为200-400 nm的PLLA纳米纤维无纺毡。     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/waterborne polyurethane nanofiber membranes in aqueous solution

Poly(vinyl alcohol) (PVA)/waterborne polyurethane (WBPU) nanofiber mats were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy (SEM), X‐ray diffraction (XRD), thermal gravimetric analyzer (TGA), and tensile strength testing machine (ZWICK) were used to characterize the morphology and properties of the PVA/WBPU nanofiber mats. The results showed that the morphologies of PVA/WBPU nanofiber mats changed with the total solid concentration and the mass ratio of PVA/WBPU in the spinning solution. The tensile strength and thermal stability of the fibers could be significantly affected by the WBPU contents. The electrospun PVA/WBPU membranes showed higher water uptake, which would have potential applications in wound dressings. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly(ethylene oxide), poly(vinyl alcohol), and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water present in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2147–2157, 1998     

Mass production of carbon nanotube reinforced poly(methyl methacrylate) nonwoven nanofiber mats

Forcespinning® technology was used to study large-scale production of conductive nonwoven nanofiber composite mats. Carboxyl functionalized multi-walled carbon nanotubes (CNT) were used to reinforce poly(methyl methacrylate) (PMMA). Composite nanofibers were developed with average diameters ranging from 370 nm to 800 nm depending on the selected processing parameters. It was found that the most influential processing parameters were viscosity of the solution and angular velocity used in the system. SEM revealed polymer wetted CNT aligned and oriented along the axis of the nanofibers. The mechanical and electrical properties of the composites were improved, compared to those of the pristine PMMA nanofibers. A 10 orders of magnitude drop in electrical resistivity and an electromagnetic shielding effectiveness of more than 20 db were obtained. Raman and Fourier transform infrared spectroscopy analyses indicated changes on the asymmetry of the polar bonds due to interactions between the CNTs and the matrix.     

Characterization of sodium alginate and poly(vinyl alcohol) blend membranes in pervaporation separation

By blending a rigid polymer, sodium alginate (SA), and a flexible polymer, poly(vinyl alcohol) (PVA), SA/PVA blend membranes were prepared for the pervaporation separation of ethanol–water mixtures. The rigid SA membrane showed a serious decline in flux and a increase in separation factor due to the relaxation of polymeric chains, whereas the flexible PVA membrane kept consistent membrane performance during pervaporation. Compared with the nascent SA membrane, all of the blend membranes prepared could have an enhanced membrane mobility by which the relaxation during pervaporation operation could be reduced. From the pervaporation separation of the ethanol–water mixtures along with the temperature range of 50–80°C, the effects of operating temperature and PVA content in membrane were investigated on membrane performance, as well as the extent of the relaxation. The morphology of the blend membrane was observed with PVA content by a scanning electron microscopy. The relaxational phenomena during pervaporation were also elucidated through an analysis on experimental data of membrane performance measured by repeating the operation in the given temperature range. SA/PVA blend membrane with 10 wt % of PVA content was crosslinked with glutaraldehyde to enhance membrane stability in water, and the result of pervaporation separation of an ethanol–water mixture through the membrane was discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:949–959, 1998     

Rotating-disk electrospinning: needleless electrospinning of poly(caprolactone), poly(lactic acid) and poly(vinyl alcohol) nanofiber mats with controlled morphology

As a contribution to the feasibility of high-throughput electrospinning, here we report on the investigation into the production of polymer nanofiber mats through needleless electrospinning. For this study, we used poly(caprolactone) (PCL), poly(lactic acid) (PLA) and poly(vinyl alcohol) (PVA), widely used polymers in the field of electrospinning. Optimization studies were carried out to devise the characteristics of the rotating-disk electrospinning system in order to assess the processing window for each polymer. Other factors were also considered, where the production rate, fiber size distribution, and morphology of the specimens acquired by rotating-disk electrospinning and conventional electrospinning techniques were compared. Our studies also illustrate the similarities of this novel “bottom-up” process compared to the conventional one, where a high resolution image confirmed the formation of a cone-jet structure and a Taylor Cone.     

Preparation and magnetometric characterization of iron oxide-containing alginate/poly(vinyl alcohol) networks

Alginate-based magnetic gels were prepared in a sequence of procedures for in situ synthesis of iron oxides: crosslinking of alginate in ferrous salt aqueous solution, immersion of the resulting gels into alkaline-earth metallic hydroxide solution, and treatment of the partially cation-exchanged gels with hydrogen peroxide. Magnetometry measurements revealed that the lyophilized gels showed superparamagnetism or ferromagnetism at room temperature, depending on the sort of the metallic cation employed in the alkali treatment. An interpenetrating network (IPN) type of alginate/poly(vinyl alcohol) (Alg/PVA) gels containing iron oxides was also designed and fabricated from mixed polymer solutions by a modified preparation method; the gelation and alkali treatment were carried out with the aid of a metallic borate. Viscoelasticity of the magnetic IPN composites in the gelatinous state was controllable by changing the mixing ratio of the compatible carbohydrate/viny polymer pair. Magnetization versus magnetic field curves were constructed at different temperatures for the IPNs freeze-dried. Their magnetic character was variable according to alterations of the Alg/PVA composition, alkaline reagent adopted, and measurement temperature.     

Preparation method and physical,mechanical, thermal characterization of poly(vinyl alcohol)/poly(acrylic acid) blends

A series of blends of poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) were prepared by solution mixing and casting. Glycerol was used as plasticizer. The blends were characterized for their physicochemical and thermo-mechanical properties. The FTIR results revealed the molecular level interaction between PVA and PAA at all blend ratios. The incorporation of PAA significantly reduced the storage modulus of PVA at a given temperature. PVA gradually lost its crystalline character with the increase of PAA and became fully amorphous when the PAA content in the blend exceeded 50 wt%. The kinetic parameters of the semi-crystalline blends were determined using the Avarami–Erofeev model, which showed excellent fitting with the experimental data from DSC. The loss in crystallinity of PVA also contributed to an increase in swelling of the blend when the PAA content is increased. The morphology study by FE-SEM demonstrated that there is no phase separation among the blend components at all blend ratios.     

Microstructure and characterization of electrospun poly(vinyl alcohol) nanofiber scaffolds filled with graphene nanosheets

Graphene nanosheets (GNSs) have attracted significant scientific attention because of their remarkable features, including exceptional electron transport, excellent mechanical properties, high surface area, and antibacterial functions. Poly(vinyl alcohol) (PVA) solutions filled with GNSs were prepared for electrospinning, and their spinnability was correlated with their solution properties. The effects of GNS addition on solution rheology and conductivity were investigated. The as‐spun fibers were characterized via scanning electron microscopy (SEM), transmission electron microscopy (TEM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC). The results revealed the effects of GNS on the microstructure, morphology, and crystallization properties of PVA/GNS composite nanofibers. The addition of GNSs in PVA solution increased the viscosity and conductivity of the solution. The electrospun fiber diameter of the PVA/GNS composite nanofiber was smaller than that of neat PVA nanofiber. GNSs were not only embedded at the fibers but also formed protrusions on the fibers. In addition, the crystallinity of PVA/GNS fiber decreased with higher GNS content. The possible application of PVA/GNS fibers in tissue engineering was also evaluated. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41891.     

聚乳酸/聚乙烯醇纳米纤维的制备及结构

以二甲基亚砜为溶剂,制备不同配比的聚乳酸(PLLA)和聚乙烯醇(PVA)的混合溶液,静电纺丝制得PLLA/PVA纳米纤维。采用红外光谱仪、原子力显微镜等对PLLA/PVA纳米纤维结构与性能进行了表征。结果表明:PLLA/PVA纳米纤维中PVA上的羟基与PLLA上的羰基形成了氢键,PLLA与PVA之间存在一定的相互作用,但PLLA/PVA纳米纤维存在相分离现象;混合溶液的PLLA质量分数为11%,PVA质量分数为8%时可以得到较好的PLLA/PVA纳米纤维,但PVA质量分数为6%时出现液滴及珠丝,PVA质量分数为4%时,不能制得纳米纤维。     

Preparation and electroresponsive property of poly(vinyl alcohol)/sodium alginate composite hydrogel

Poly(vinyl alcohol) (PVA)/sodium alginate composite hydrogel was prepared by solidifing the blending solution of PVA and sodium alginate, then freezing and thawing repeatedly. In the direct current electric field, the composite hydrogel in aqueous NaCl solution swelled, contracted, and bent. The gel's bending speed and maximum bending degree increased with increase in the electric field intensity and the concentration of NaCl solution. The maximum bending degree increased with increase in the sodium alginate content in the composition hydrogel. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3493–3496, 2006     

Preparation of sodium alginate/poly(vinyl alcohol) blend microspheres for controlled release applications

Sodium alginate (NaAlg)/poly (vinyl alcohol) (PVA) blend microspheres (MS) were prepared by water-in-oil (w/o) emulsion method. These polymer microspheres were crosslinked with glutaraldehyde and loaded with metformin hydrochloride (MHC). The microspheres were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis to confirm the molecular dispersion of the drug, thermal stability, morphological properties, and crystallinity of the polymer matrix before and after blending. SEM of the microspheres suggested the formation of microspheres in spherical structure. Drug release data were analyzed using an empirical equation to understand the nature of drug transport through polymeric matrices. The controlled release (CR) characteristics of the polymer matrices was investigated in pH 7.4 media and from the results it was obtained that the drug was released in controlled manner up to 10 h. The physico-chemical properties of the microspheres were studied by calculating drug entrapment efficiency and drug release kinetics. Percent of encapsulation efficiency (% EE) decreased with increase in crosslinking agent (GA) and PVA content in the microspheres. The optimum % EE (80%) was observed in case of MS containing 40% of PVA with 15% MHC. The release profiles indicate that the release of MHC decreases with increasing the PVA/NaAlg (w/w) and drug/polymer ratio. At the end of 10 h, the highest release of MHC was found to be 96% for MS containing PVA/NaAlg (40 : 60) and 15 wt % drug loaded. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Controlled release of naproxen from sodium alginate and poly(vinyl alcohol)/sodium alginate blend beads crosslinked with glutaraldehyde

In this study, polymeric beads of sodium alginate (NaAlg) and its blend with poly(vinyl alcohol) (PVA) were prepared by crosslinking with glutaraldehyde (2.5% v/v) and hydrochloric acid (3% v/v) for the release of naproxen sodium (NS). The prepared beads were characterized with Fourier transform infrared spectroscopy, and pictures of the beads were determined with an optic microscope. The release studies were carried out at three pH values (1.2, 6.8, and 7.4) for 2 h. The effects of the preparation conditions, including the PVA/NaAlg (w/w) ratio, drug/polymer (w/w) ratio, and time of exposure to the crosslinker, on the release of NS were investigated for 10 h at 37°C. The release of NS decreased with the PVA/NaAlg (w/w) ratio and drug/polymer ratio increasing. At the end of 10 h, the highest release of NS was found to be 84% for the 1/2 PVA/NaAlg (w/w) ratio. The swelling measurements of the beads supported the release results. The release kinetics were described with Fickian and non‐Fickian approaches. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Oil- and water-resistant paper substrate using blends of chitosan-graft-polydimethylsiloxane and poly(vinyl alcohol)

Reported herein is an economical, plastic- and fluorine-free coating approach for oil and water repellent paper substrates using blends of poly(vinyl alcohol) and chitosan-graft-polydimethylsiloxane copolymer. The obtained coated paper showed good water-resistance, as evidenced by its low Cobb60 values of ~20 ± 2.1 g/m² and high water contact angles of 119 ± 6.3 °. The kit rating of the coated paper was 7.6/12, indicating decent grease-resistant properties as compared to the kit value of 0/12 for the uncoated paper. The coated paper is also repulpable as demonstrated by the complete washing off the coating from the coated paper. Giving the cost-effective nature of the coating materials and good water and oil-resistant properties of the coated paper, the approach developed here is commercially viable, and will offer a multitude of environmental benefits such as the elimination of microplastic- and PFAS problems associated with existing paper coatings.     

Study of miscibility of poly(vinyl acetate) and poly(vinyl alcohol) blends by fluorescence spectroscopy

Secondary relaxation of poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), and their blends in different proportions (9 : 1, 1 : 1, and 1 : 9) were studied by photoluminescence of anthracene, fluorescein, and both probes dissolved in the polymer blends. The temperature of the glass transition in the homopolymers was determined by the radiationless deactivation of anthracene as T_g(PVAc) ? 304 K and the photobleaching of fluorescein as T_g(PVA) ? 350 K. The relaxation processes of the different phases of the polymer blends occur at temperatures close to the homopolymers, which may be explained by the localization of each molecular probe within the matrix. These deactivation curves, however, are not similar to those of the individual homopolymers, suggesting a partial miscibility between these polymers. © 1995 John Wiley & Sons, Inc.