Fatty acid methyl ester heterogeneous self‐metathesis in hydrophobic green solvent: Mass transfer limitations,catalyst recyclability,and stability

The role of room‐temperature ionic liquids (RTILs), [bmim][PF₆] and [bmim][Tf₂N], as reaction media regarding the catalytic activity and stability of methyltrioxorhenium (MTO) supported on ZnCl₂‐modified mesoporous Al₂O₃ has been studied for self‐metathesis of a functionalized olefin, methyl oleate. The humidity influence on the catalytic activity was probed. The catalyst recycling ability and the kinetics of the metathesis reaction using these RTILs were also investigated. It was found that the MTO‐based catalyst was efficient in viscous hydrophobic RTIL solvents. However, their high viscosity was found to increase the mass transfer limitations thus somewhat impacting the reaction kinetics. Nevertheless, better catalyst stability was reached allowing its possible recycling when used in RTIL media.     

Negative effect of [bmim][PF6] on the catalytic activity of alcohol dehydrogenase: mechanism and prevention

BACKGROUND: [bmim][PF₆] is a hydrophobic ionic liquid which could be considered as an environmentally friendly solvent for biocatalysis. In pure [bmim][PF₆], however, alcohol dehydrogenase from yeast (YADH) has no catalytic activity. The aim of the present work was (1) to quantitatively study the negative effect of [bmim][PF₆] on the catalytic activity of YADH and the related mechanism and (2) to made an attempt to lessen the negative effect of [bmim][PF₆] on YADH by microemulsifying [bmim][PF₆]. RESULTS: The activity of YADH in the homogeneous solution formed by H₂O, CH₃CH₂OH and [bmim][PF₆] decreased rapidly with the increase of the molar fraction of [bmim][PF₆]. The inhibitory effect of [bmim][PF₆] on YADH was probably caused by the competition of the imidazole group of [bmim][PF₆] with the coenzyme NAD⁺ for the binding sites on YADH. In a water‐in‐[bmim][PF₆] microemulsion, YADH was catalytically active due to the formation of the interfacial membrane of the nonionic surfactant TritonX‐100, which separated YADH from [bmim][PF₆] and avoided the direct inactivation of [bmim][PF₆] on YADH. Under optimal conditions, the activity of YADH was as high as 51 µmol L^?1 min^?1. CONCLUSION: [bmim][PF₆] was an inhibitor of YADH and its negative effect on YADH could be lessened by its microemulsification. Copyright © 2008 Society of Chemical Industry     

Effect of ionic liquids on the structural,thermal, and in vitro degradation properties of poly(ε‐caprolactone) synthesized in the presence of Candida antarctica lipase B

The study provides detailed information on the differences in the structural, thermal and degradation properties of poly(ε‐caprolactone) synthesized in two different ionic liquids, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [bmim][PF₆] and 1‐butyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide [bmim][NTf₂], regarding its further usage in the pharmaceutical field. The polymer structure confirms the presence of both linear polymer chains with end‐functional hydroxyl groups allowing covalent coupling of the therapeutic agents, and cyclic macromolecules, both affecting the degree of crystallinity of polymer. The highest macrocyclic content (64%) after 7 days of polymerization at 80 °C was observed for [bmim][NTf₂]. For [bmim][PF₆], the macrocyclic content value was not dependent on the reaction time and remained at a similar level (10–14% at 80 °C). The results of degradation test revealed that hydrolytic degradation of ester bonds is more pronounced for PCLs synthesized in [bmim][NTf₂], due to their lower degree of crystallinity compared with PCLs obtained in [bmim][PF₆]. A high purity, low polydispersity index of the obtained polymers and high yield of the process (ca., 90%) indicate that ionic liquids seem to be promising solvents for the synthesis of biomedical polymers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43728.     

Effect of the ionic liquid [bmim]PF6 on the nonisothermal crystallization kinetics behavior of poly(ether‐b‐amide)

Blending ionic liquid with crystalline polymer permits the design of new high‐performance composite materials. The final properties of these materials are critically depended on the degree of crystallinity and the nature of crystalline morphology. In this work, nonisothermal crystallization behavior of poly(ether‐b‐amide) (Pebax®1657)/room temperature ionic liquid (1‐butyl‐3‐methylimidazolium hexafluorophosphate, [bmim]PF₆) was investigated by differential scanning calorimetry. The presence of [bmim]PF₆ can retard the nucleation of Pebax®1657 and lead to the crystallization depression of the PA block and the crystalline disappearance of the PEO block. However, the dilution effect of the IL results in a higher growth rate of crystallization of PA block. The influence of [bmim]PF₆ content and cooling rate on crystallization mechanism and spherulitc structures was determined by the Avrami equation modified by Jeziorny and Mo's methods, whereas the Ozawa's approach fails to describe the nonisothermal crystallization behavior of Pebax®1657/[bmim]PF₆ blends. In the modified Avrami analysis, the Avrami exponent of PA blocks, n > 3, for pure Pebax®1657, while 3 > n > 2 for Pebax®1657/[bmim]PF₆ blends testifies the transformation of crystallization growth pattern induced by [bmim]PF₆ from three‐dimensional growth of spherulites to a combination of two‐ and three‐dimensional spherulitic growth. Further, lower activation energy for the nonisothermal crystallization of PA blocks of Pebax®1657 can be observed with the increase of [bmim]PF₆ content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42137.     

Preparation and characterization of room temperature ionic liquid/single-walled carbon nanotube nanocomposites and their application to the direct electrochemistry of heme-containing proteins/enzymes

This work describes the formation and possible electrochemical application of a novel nanocomposite based on single-walled carbon nanotubes (SWNTs) and imidazolium-based room-temperature ionic liquids (RTILs) of 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim]BF₄, a hydrophilic RTIL) and 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim]PF₆, a hydrophobic RTIL). The nanocomposites ([bmim]BF₄-SWNTs, and [bmim]PF₆-SWNTs) were formed by simply grinding the SWNTs with the respective RTIL. The results of the X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy indicated that the nanocomposites were formed by adsorption of an imidazolium ion on the surface of SWNTs via the “cation-π” interaction. SEM images showed that [bmim]BF₄-SWNTs (or [bmim]PF₆-SWNTs) nanocomposites could uniformly cover the surface of a glassy carbon (GC) electrode resulting in a RTILs-SWNTs/GC modified electrode with a high stability. The RTILs-SWNTs composite could be readily used as a matrix to immobilize heme-containing proteins/enzymes (myoglobin, cytochrome c, and horseradish peroxidase) without undergoing denaturation, as was verified by UV-vis and circular dichroic (CD) spectroscopic results. The voltammetric results showed that heme-containing proteins/enzymes entrapped in RTILs-SWNTs composites displayed a pair of well-defined, stable redox peaks, which were ascribed to their direct electron-transfer reactions. The results of controlled experiments showed that the positive charged imidazolium ion played a significant effect on the electrochemical parameters, such as the redox peak separation and the value of the formal potentials, etc., of the electron-transfer reaction of non-neutral species dissolved in solution or immobilized on the electrode surface. Further results demonstrated that the heme-containing proteins/enzymes entrapped in RTILs-SWNTs composites could still retain their bioelectrocatalytic activity toward the reduction of oxygen and hydrogen peroxide. The results depicted in this work may pave a new avenue to electrocatalysis, proteins/enzymes electrochemistry, and bioelectrochemical synthesis, etc.     

Characterization of Absorption Performance for Gaseous Acetone with Ionic Liquid Solutions

New absorbents composed of diethylene glycol monobutyl ether (DGBE), paraffin oil, and ionic liquids (ILs) were prepared for the removal of gaseous acetone. Three ILs, namely, [bmim][PF₆], [bmim][BF₄], and [bmim][Ac], were used to regulate the absorption performance. Different paraffin oil mass fractions and IL mass fractions were applied to determine the right formula with suitable physical properties and absorption performance. The Henry coefficients of acetone in the absorbents were measured to evaluate the influence of absorbent composition on the absorption capacity. The removal performances of these absorbents were investigated in a bubbling bottle to evaluate the combined impact of Henry coefficient and physical properties.     

Effect of multi‐walled carbon nanotubes on crystallization,thermal, and mechanical properties of poly(vinylidene fluoride)

Composites were prepared by solution blending poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWNTs). Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) results showed that the crystalline structure of PVDF was changed by the addition of MWNTs and a MWNTs‐induced crystal transformation from α‐phase to β‐phase of PVDF was confirmed. With differential scanning calorimeter (DSC) and dynamic mechanic thermal analysis (DMA) techniques, thermal and mechanical properties of the composite films were examined. As the DSC results showed, addition of MWNTs would lead to the increased cooling crystallization temperature (T_c), implying that MWNTs nanoparticles could act as nucleating agents, which is further proved with the help of polarized optical microphotographs. On the other hand, the decreasing of D_d (degree of crystallinity) implied that the MWNTs networks can confine the crystallization of PVDF. Through the curve analysis of the dynamic mechanical measurements, it was found that the storage modulus (E′) is significantly enhanced, revealing that a strong interaction should exist between PVDF and MWNTs. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Understanding of intermolecular interaction in PVDF/PTW blends: Crystallization behavior,thermal, and dynamic mechanical properties

Poly(vinylidene fluoride) (PVDF)/ poly(ethylene–butylacrylate–glycidyl methacrylate) (PTW) blends were directly prepared by melt blending and the interaction and properties of PVDF/PTW blends were explored systematically. The crystallization behavior, thermal stability, dynamic mechanical property, and morphological features of PVDF/PTW blends with different ratios have been studied by XRD, attenuated total reflection Fourier transform infrared spectroscopy, differential scanning calorimeter analysis (DSC), thermal gravimetric analysis (TGA), dynamic mechanical analysis, and polarized optical microscopy (POM). The results showed that the crystalline structure of neat PVDF was dominantly α‐phase crystalline and the incorporation of PTW had no effect on the crystalline structure of PVDF in the PVDF/PTW blends. And T_g of PVDF in PVDF/PTW blends shifted to higher temperature compared with that of neat PVDF, indicating the weak interaction between PVDF and PTW, which was corresponding to DSC and TGA results. An increase in the coarseness and ring‐band spacing observed from POM further substantiated the weak interaction between PVDF and PTW. This work provided a way for preparing improved properties of PVDF/PTW blends for the coating material. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43908.     

Catalytic Activity of Pd(II) Complexes with Triphenylphosphito Ligands in the Sonogashira Reaction in Ionic Liquid Media

The reactivity of palladacycle dimeric complexes with substituted triarylphosphito ligands P(OR)₃ (R = Ph, m-MeC₆H₄, o-MeC₆H₄, C₆H₃-2,4-tBu₂) as well as their non-orthometallated analogues PdCl₂[P(OR)₃]₂ was tested in a copper-free Sonogashira reaction with iodobenzene and phenylacetylene as substrates and imidazolium ionic liquids as the reaction medium. The ionic liquids [bmim][PF₆], [bmim][BF₄] and [emim][SO₄Et] were chosen. The palladium complexes studied showed high activity, and the yield of diphenylacetylene ranged from 31 to 98% in 1 h. The best results were obtained in [bmim][PF₆] for PdCl₂[P(O-m-MeC₆H₄)₃]₂ (84%) and for orthopalladated dimer with the same phosphite (98%).     

Physical and electrochemical properties of 1-butyl-3-methylimidazolium bromide, 1-butyl-3-methylimidazolium iodide,and 1-butyl-3-methylimidazolium tetrafluoroborate

The density, viscosity, refractive index, heat capacity, heat of dilution, ionic conductivity, and electrochemical stability of 1-butyl-3-methylimidazolium bromide ([bmim][Br]), 1-butyl-3-methylimidazolium iodide ([bmim][I]), and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]) were measured at room temperature or over a temperature range of 293.2 to 323.2 K. The density and refractive index values of [bmim][I] appeared to be the highest among three ionic liquids (ILs). However, the experimental viscosity values of [bmim][Br] were higher than those of [bmim][BF₄], while the heat capacities and heats of dilution of [bmim][BF₄] were higher than those of [bmim][Br]. The cyclic voltammogram of [bmim][br] and [bmim][BF₄] indicated electrochemical windows in the stability range from 2.7 V of [bmim][[Br] to 4.7 V of [bmim][BF₄].     

Microfluidic room temperature ionic liquid droplet generation depending on the hydrophobicity and interfacial tension

We have characterized micro-droplet generation using water immiscible hexafluorophosphate ([PF₆])- and bis(trifluoromethylsulfonyl)imide ([Tf₂N])-based room temperature ionic liquids (RTILs). The interfacial tension between total 7 RTILs and phosphate buffered saline (PBS) was measured using a tensiometer for the first time. PBS is one of the most commonly used buffer solutions in cell-related researches. The measured interfacial tension ranges from 8.51 to 11.62 and from 9.56 to 13.19 for [Tf₂N]- and [PF₆]-based RTILs, respectively. The RTILs micro-droplets were generated in a microfluidic device. The micro-droplet size and generation frequency were determined based on continuous monitoring of light transmittance at the interface in microchannel. The size of RTIL micro-droplets was inversely proportional to the increase of PBS solution flow rate and RTILs hydrophobicity, while droplet generation frequency was proportional to those changes. The measured size of RTILs droplets ranged from 0.6 to 10.5 nl, and from 1.0 to 17.1 nl for [Tf₂N]- and [PF₆]-based RTILs, respectively. The measured frequency of generated RTILs droplets ranged from 2.3 to 37.2 droplet/min, and from 2.7 to 17.1 droplet/min for [Tf₂N]- and [PF₆]-based RTILs, respectively. The capillary numbers were calculated depending on the RTILs, and ranged from 0.51×10^-3 to 1.06×10^-3 and from 5.00×10^-3 to 8.65×10^-3, for [Tf₂N]- and [PF₆]-based RTILs, respectively. The interfacial tension between RTILs and PBS will contribute to developing bioprocesses using immiscible RTILs. Also, the RTILs micro-droplets will enable the high-throughput monitoring of various biological and chemical reactions using RTILs as new reaction media.     

Crystal transformation and thermomechanical properties of poly(vinylidene fluoride)/clay nanocomposites

The crystal transformation and thermomechanical properties of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported in this study. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to study the thermal properties of PVDF and its nanocomposites with various clay concentrations. The incorporation of clay in PVDF results in the formation of β‐form crystals of PVDF. DSC study of melting behavior suggested the presence of only α‐phase crystals in neat PVDF and both α‐ and β‐phase crystals in the nanocomposite. This conclusion was corroborated by findings from Fourier‐transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD). Dynamic mechanical analysis (DMA) indicated significant improvements in storage modulus over a temperature range of 20–150 °C. The coefficient of thermal expansion (CTE) decreases with increasing clay loading. Copyright © 2004 Society of Chemical Industry     

Improved activity and stability of pseudomonas capaci lipase in a novel biocompatible ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate

BACKGROUND: Enzymes may exhibit enhanced activity, stability and selectivity in ionic liquids, depending on the properties of the liquid. The physical–chemical properties of ionic liquids, however, may be modified by altering the anion or cation in the ionic liquid. This feature is a key factor for realizing successful reactions. In this work, a new ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [i‐C₄mim][PF₆]), was synthesized and investigated as a novel medium for the transesterification reaction of 2‐phenylethanol with vinyl acetate catalyzed by pseudomonas capaci lipase. As contrasts, the reaction was also carried out in two reference solvents; the isomeric ionic liquid [i‐C₄mim][PF₆], 1‐butyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [C₄mim][PF₆]), and hexanes. RESULTS: As reaction medium, [i‐C₄mim][PF₆] was best among the three solvents. The initial reaction rate, the equilibrium conversion of 2‐phenylethanol and the half‐lifetime of the lipase in [i‐C₄mim][PF₆] medium were about 1.5, 1.2 and 3‐fold that obtained in [C₄mim][PF₆] medium, respectively. The lipase in [i‐C₄mim][PF₆] medium was recycled 10 times without substantial diminution in activity. CONCLUSION: The ionic liquid [i‐C₄mim][PF₆] has good biocompatibility, and can be used widely as green media in various biocatalysis reactions to improve the activity and stability of enzymes. Besides hydrophobicity and nucleophilicity, the spatial configuration of ionic liquids is also considered a key factor effecting the behaviour of the enzyme in ionic liquids. Copyright © 2008 Society of Chemical Industry     

Asymmetric Glyoxylate-Ene Reactions Catalyzed by Chiral Pd(II) Complexes in the Ionic Liquid [bmim][PF6]

The room temperature ionic liquid [bmim][PF₆] was employed as the reaction medium in the asymmetric glyoxylate-ene reaction of α-methyl styrene (4a) with ethyl glyoxylate using chiral palladium(II) complexes as the catalysts. [Pd(S-BINAP)(3,5-CF₃-PhCN)₂](SbF₆)₂ (1b) showed the highest catalytic activity. Under the reaction conditions of 40 °C, 0.5 h, and 1b/4a molar ratio of 0.05, ethyl α-hydroxy-4-phenyl-4-pentenoate was obtained in excellent chemical yield (94 %) with high enantioselectivity (70 %). Other α-hydroxy esters can also be obtained in high chemical yields and enantioselectities through the glyoxylate-ene reactions of alkenes with glyoxylates catalyzed by 1b in [bmim][PF₆]. Moreover, the ionic liquid [bmim][PF₆] which contained the palladium(II) complex could be recycled and reused several times without significant loss of the catalytic activity.     

Enhanced electroactive phase,toughness and dielectric properties of poly(vinylidene fluoride) with addition of MMA-BA-IL copolymer

Methyl methacrylate (MMA), butyl acrylate (BA) and 1-butyl-3-vinylimdazolium tetrafluoroborate ([BVIM][BF₄]) copolymer (MMA-BA-IL) was prepared and used to enhance the electroactive phase content, toughness and dielectric properties of poly(vinylidene fluoride) (PVDF). Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) tests indicated that crystal transformation of PVDF from α-phase to β/γ-phase occurred due to ion-dipole interaction between PVDF and [BVIM][BF₄]. Scanning electron microscope (SEM) results showed MMA-BA-IL copolymer dispersed in the PVDF uniformly and the partial replacement of MMA components by [BVIM][BF₄] decreased the miscibility between PVDF and MMA-BA copolymer. MMA-BA-IL copolymer improved the tensile ductility and impact toughness of PVDF. When the content of MMA-BA-IL was beyond 10 wt%, the elongation at break was higher than 400% and the impact strength was higher than 600 J/m. Deformation mechanism researches proved that shear yielding of the PVDF matrix and debonding/cavitation of the MMA-BA-IL copolymer particles were the major toughening mechanisms. The addition of MMA-BA-IL copolymer enhanced the dielectric properties of PVDF significantly. When the MMA-BA-IL content was 15 wt%, the dielectric constant of the PVDF/MMA-BA-IL blend increased to 54.3 at the 100 Hz frequency, which improved by 246% relative to that of the pure PVDF.     

Preparation of well-defined dendrimer encapsulated ruthenium nanoparticles and their application as catalyst and enhancement of activity when utilised as SCILL catalysts in the hydrogenation of citral

Silica supported dendrimer encapsulated ruthenium nanoparticles were prepared and evaluated as catalysts in the hydrogenation of citral. The dendrimer encapsulated nanoparticles were prepared using the generation 4 (G4), generation 5 (G5) and generation 6 (G6) hydroxyl-terminated poly(amidoamine) (PAMAM-OH) dendrimers as templating agents with different Ru metal:dendrimer ratios. The effects of ionic liquids as catalyst coatings on the catalytic activity were investigated for the ionic liquids [BMIM][NTf₂], [OMIM][NTf₂], [BMIM][BF₄], [BMIM][PF₆], [EMIM][OcS] and [EMIM][EtS]. An enhancement in catalytic activity was observed when utilising [BMIM][NTf₂] as an ionic liquid coating with selectivity towards citronellal.     

1‐Allyl‐3‐methylimidazolium halometallate ionic liquids as efficient catalysts for the glycolysis of poly(ethylene terephthalate)

Series of 1‐allyl‐3‐methylimidazolium halometallate ionic liquids (ILs) were synthesized and used to degrade poly(ethylene terephthalate) (PET) as catalysts in the solvent of ethylene glycol. One important feature of these new IL catalysts is that most of them, especially [amim][CoCl₃] and [amim][ZnCl₃], exhibit higher catalytic activity under mild reaction condition, compared to the traditional catalysts [e.g., Zn(Ac)₂], the conventional IL catalysts (e.g., [bmim]Cl), Fe‐containing magnetic IL catalysts (e.g., [bmim][FeCl₄]), and metallic acetate IL catalysts (e.g., [Deim][Zn(OAc)₃]). For example, using [amim][ZnCl₃] as catalyst, the conversion of PET and the selectivity of bis(hydroxyethyl) terephthalate (BHET) reach up to 100% and 80.1%, respectively, under atmospheric pressure at 175°C for only 1.25 h. Another important feature is that BHET can be easily separated from the catalyst and has a high purity. Finally, based on the experimental phenomena, in ‐situ infrared spectra, and experimental results, the possible mechanism of degradation with synthesized IL is proposed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Room temperature ionic liquids in electrosynthesis and spectroelectrochemical characterization of poly(para-phenylene)

Room temperature ionic liquids (RTILs) were used in electrochemical polymerization and in doping studies (oxidation and reduction) of poly(para-phenylene) (PPP). Cyclic voltammetry was used simultaneously with Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) spectroscopy. Electropolymerization and doping of PPP were done by potential scanning in acetonitrile (ACN + 0.1 M TBAPF₆), 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]) and butylmethylpyrrolidinium bis (trifluoromethylsulfonyl) imide ([BMP][Tf₂N]). The cyclic voltammograms recorded during polymerization of the PPP film indicate that the best film growth was achieved in [BMIM][PF₆]. The films made in [BMP][Tf₂N] were more stable than films made in ACN (0.1 M TBAPF₆). Results from p-doping studies show that doping can be made at higher potentials in RTILs than in ACN (0.1 M TBAPF₆). It was also found that n-doping can be performed in RTILs at higher negative potentials (−2.2 V) than in ACN (0.1 M TBAPF₆) (−1.8 V). The best n-doping response was achieved in [BMP][Tf₂N]. Also, n-doping in [BMIM][PF₆] was better than in ACN (0.1 M TBAPF₆). The in situ ATR-FTIR spectroscopy was used to study p- and n-doping of PPP films. During both p- and n-doping the spectra indicated formation of infrared active vibration bands (IRAV) in the wavenumber region 1600-800 cm⁻¹. The obtained IRAV bands correlate to the theoretical modes calculated by Zerbi and co-workers according to the effective conjugation coordinate theory (ECC). All these results indicate that RTILs are good solvents in spectroscopic and electrochemical studies of conducting polymers.     

Ionic liquid effects on the reaction of β-enaminones and tert-butylhydrazine and applications for the synthesis of pyrazoles

In order to evaluate the effect of a series of 10 different ionic liquids ([BMIM][BF₄], [BMIM][Br], [OMIM][BF₄], [BMIM][PF₆], [DBMIM][Br], [DBMIM][BF₄], [BMIM][OH], [BMIM][SCN], [HMIM][HSO₄] and [HMIM][CF₃CO₂]) the cyclocondensation reaction between 4-dimethylamino-1-phenyl-3-alken-2-ones (RC(O)CHCHNMe₂, where R = Ph, 4-Me-Ph, 4-F-Ph, 4-Cl-Ph, 4-Br-Ph, 4-NO₂-Ph, thien-2-yl, fur-2-yl, pyrrol-2-yl, pyrid-2-yl, hexyl, dimethoxymethyl) and tert-butylhydrazine was performed. The effects of each ionic liquid are discussed and the best yields for the cyclocondensation reaction studied were obtained using [BMIM][BF₄].     

Critical properties and acentric factors of ionic liquids

Since most ionic liquids (ILs) decompose before reaching their critical state, the experimental measurement of their critical properties are not possible. In this study, the critical temperatures, critical pressures and acentric factors of ten commonly investigated ILs were determined by making an optimum fit of the calculated vapor-liquid equilibrium data of binary mixtures of CO₂+IL to the experimental values found in literature. For this purpose, the Peng-Robinson equation of state (PR EoS) and the differential evolution optimization method were used. The ILs considered were 1-ethyl-3-methylimidazolium hexafluorophosphate ([emim][PF₆]), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([emim][Tf₂N]), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([bmim][Tf₂N]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim][BF₄]), 1-hexyl-3-methylimidazolium hexafluorophosphate ([hmim][PF₆]), 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([hmim][Tf₂N]), 1-octyl-3-methylimidazolium tetrafluoroborate ([omim][BF₄]) and 1-octyl-3-methylimidazolium hexafluorophosphate ([omim][PF₆]). To evaluate the ability of the determined parameters in predicting the phase behavior of systems other than the systems that were used for parameter optimization, both sets of parameters obtained in this work and that of Valderrama et al. were used to predict bubble-point pressures of CHF₃+[bmim][PF₆] (by using the PR EoS and the Soave-Redlich-Kwong equation of state. The bubble-point pressures of CO₂+IL systems optimized in this study by the PR EoS were also determined using the Soave-Redlich-Kwong equation of state (SRK EoS). In addition, liquid densities of pure ILs were predicted using a generalized correlation proposed by Valderrama and Abu-Shark. In all cases, the various predicted properties of these ten ILs, were in better agreement with the experimental data, using the critical properties and acentric factor obtained in this study, compared to the values suggested by Valderrama et al.