Preparation and characterization of polyethylene–clay nanocomposites by using chlorosilane‐modified clay

Clay was modified by trimethylchlorosilane; after modification, hydroxyl groups at the edge of layers were reacted and CEC value was drastically decreased. Polyethylene–clay composites were prepared by melt compounding. Wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) showed that intercalated nanocomposites were formed using organoclay ion‐exchanged from chlorosilane‐modified clay, but conventional composites formed using organoclay directly ion‐exchanged from crude clay. Dynamic mechanical analysis (DMA) of PE and PE–clay composites was conducted; the results demonstrated that nanocomposites were more effective than conventional composites in reinforcement and addition of organoclay resulted in the increase of glass transition temperature (T_g), but crude clay had no effect on T_g of PE–clay composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 676–680, 2004     

Physical properties of poly(trimethylene terephthalate)/organoclay nanocomposites obtained via melt compounding and in situ polymerization

Two series of poly(trimethylene terephthalate) (PTT) nanocomposites, containing an organically modified montmorillonite (MMT) clay (1,2‐aminododecanoic acid (ADA)–intercalated MMT) were prepared via melt compounding and in situ polymerization methods using dimethyl terephthalate (DMT) and 1,3‐propanediol (PDO). The effect of different methods of preparation and varying organoclay contents (1−5 wt%) on the structural, morphological, thermal, and mechanical properties were investigated. The results of wide‐angle X‐ray diffraction (WAXD) and transmission electron microscope (TEM) suggested the possible existence of intercalation morphology between ADA‐MMT and the PTT matrix obtained from melt compounding, and mostly exfoliation state from in situ polymerization depending on the amount of organoclay. From DSC studies, in melt compounding case, the addition of ADA‐MMT in PTT increases melt‐crystallization (T_cm) peak temperature by 14−15°C irrespective of the clay content. However, the melting temperature (T_m) of pristine PTT remains unchanged with increasing clay content. In the case of in situ polymerization, the T_cm and T_m peaks are shifted towards lower temperature with increasing clay content. Dynamic mechanical thermal analysis (DMTA) studies on melt compounded samples revealed a marginal lowering of glass transition temperature (T_g) irrespective of clay content, and a noticeable decrease in T_g with increasing clay content for in situ polymerized samples. The PTT/ADA‐MMT nanocomposites via melt compounding showed higher initial modulus and yield stress, and lower strain at break compared with in situ polymerization with increasing clay content. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Preparation and characterization of poly(styrene‐co‐butadiene) and polybutadiene rubber/clay nanocomposites

Poly(styrene‐co‐butadiene) rubber (SBR) and polybutadiene rubber (BR)/clay nanocomposites have been prepared. The effects of the incorporation of inorganically and organically modified clays on the vulcanization reactions of SBR and BR were analysed by rheometry and differential scanning calorimetry. A reduction in scorch time (t_s1) and optimum time (t₉₅) was observed for both the rubbers when organoclay was added and this was attributed to the amine groups of the organic modifier. However, t_s1 and t₉₅ were further increased as the clay content was increased. A reduction in torque value was obtained for the organoclay nanocomposites, indicating a lower number of crosslinks formed. The organoclays favoured the vulcanization process although the vulcanizing effect was reduced with increasing clay content. The tensile strength and elongation of SBR were improved significantly with organoclay. The improvement of the tensile properties of BR with organoclay was less noticeable than inorganic‐modified clay. Nevertheless, these mechanical properties were enhanced with addition of clay. The mechanical properties of the nanocomposites were dependent on filler size and dispersion, and also compatibility between fillers and the rubber matrix. Copyright © 2004 Society of Chemical Industry     

Manipulating the microstructure and rheology in polymer‐organoclay composites

A series of nanocomposites prepared by melt‐blending of cloisite‐based organoclays with poly(ethylene‐vinylacetate) (EVA) and neutralized poly (ethylene‐methacrylic acid) (EMA) copolymers were investigated via DSC, small‐angle X‐ray scattering (SAXS), and rheological techniques. SAXS results indicated partial clay exfoliation in all samples. In both EMA and EVA systems, the nominal melting temperature T_m and bulk crystallinity are not significantly affected by the presence of organoclays, suggesting that clay particles are predominantly confined in the amorphous phase. In rheological measurements (above T_m), the EVA‐clay system demonstrated a solid‐like rheological behavior under the small‐strain oscillatory shear, yet it was able to yield and flow under a steady shear, which is the characteristic of physical crosslinking. In contrast, the EMA‐clay system exhibited a melt‐like rheological behavior, where the influence of organoclay on the thermorheological behavior of the EMA composite was quite minimal. We propose that the carbonyl groups of vinylacetate in EVA interact with the clay surface, resulting in a strong physically crosslinking like interaction in the melt. On the other hand, the interaction between EMA and clay is weak because of repulsion between carboxyl anions and negatively charged clay surface.     

Tapioca starch‐poly(lactic acid)‐Cloisite 30B nanocomposite foams

Tapioca starch (TS), poly(lactic acid) (PLA), and Cloisite 30B nanocomposite foams, with four clay contents of 1, 3, 5, 7 wt%, were prepared by a melt‐intercalation method. Selected structural, thermal, physical, and mechanical properties were characterized using X‐ray diffraction, scanning electron microscopy, differential scanning calorimetry, thermogravimetry analyses, and an Instron universal testing machine, respectively. XRD results indicated that intercalation of TS/PLA into the nanoclay layers occurred in all four nanocomposite foams. At the same time, tactoid structures were observed in all nanocomposite foams but to a lesser extend with 1 and 3 wt% clay contents. Effect of clay content on melting temperature (T_m), onset degradation temperature, radial expansion ratio, unit density, bulk compressibility and bulk spring index of the nanocomposites were investigated. Among the four nanocomposites, 3 wt% clay content produced significantly different (p < 0.05) properties. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Coincorporation of nano‐silica and nano‐calcium carbonate in polypropylene

In this study, various polypropylene (PP) nanocomposites were prepared by melt blending method. The effects of different spherical nanofillers, such as 50 nm CaCO₃ and 20 nm SiO₂, on the linear viscoelastic property, crystallization behavior, morphology and mechanical property of the resulting PP nanocomposites were examined. Rheological study indicated that coincorporation of nano‐SiO₂ and nano‐CaCO₃ favored the uniform dispersion of nanoparticles in the PP matrix. Differential scanning calorimeter (DSC) and polarizing optical microscopy (POM) studies revealed that the coincorporation of SiO₂ and CaCO₃ nanoparticles could effectively improve PP crystallizability, which gave rise to a lower supercooling temperature (ΔT), a shorter crystallization half‐life (t_1/2) and a smaller spherulite size in comparison with those nanocomposites incorporating only one type of CaCO₃ or SiO₂ nanoparticles. The mechanical analysis results also showed that addition of two types of nanoparticles into PP matrix gave rise to enhanced performance than the nanocomposites containing CaCO₃ or SiO₂ individually. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of BCDA‐based polyimide–clay nanocomposites

Bicyclo[2.2.2]oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride (BCDA)‐based polyimide–clay nanocomposites were prepared from their precursor, namely polyamic acid, by a solution‐casting method. The organoclay was prepared by treating sodium montmorillonite (Kunipia F) clay with dodecyltrimethylammonium bromide at 80 °C. Polyamic acid solutions containing various weight percentages of organoclay were prepared from 4,4′‐(4,4′‐isopropylidenediphenyl‐1,1′‐diyldioxy)‐dianiline and BCDA in N‐methyl‐2‐pyrrolidone containing dispersed particles of organoclay at 20 °C. These solutions were cast on a glass plate using a Doctor's blade and then heated subsequently to obtain nanocomposite films. The nanocomposites were characterized using Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal mechanical analysis, dynamic mechanical analysis, polarizing microscopy, scanning electron microscopy, transmission electron microscopy, wide‐angle X‐ray diffraction (WAXD) and thermogravimetric analysis. The glass transition temperature of the nanocomposites was found to be higher than that of pristine polymer. The coefficient of thermal expansion of the nanocomposites decreased with increasing organoclay content. WAXD studies indicated that the extent of silicate layer separation in the nanocomposite films depended upon the organoclay content. Tensile strength and modulus of the nanocomposite containing 1% organoclay were significantly higher when compared to pristine polymer and other nanocomposites. The thermal stability of the nanocomposites was found to be higher than that of pristine polymer in air and nitrogen atmosphere. Copyright © 2007 Society of Chemical Industry     

Preparation and cure behavior of organoclay‐modified allyl‐functional benzoxazine resin and the properties of their nanocomposites

A new type of polybenzoxazine‐clay nanocomposites were prepared by the in‐situ polymerization of allyl‐functional benzoxazine monomer, bis(3‐allyl‐3,4‐dihydro‐2H‐1,3‐benzoxazinyl)isopropane (B‐ala), in the presence of two different types of organoclay, allyldimethylstearylammonium‐montmorillonite and propyldimethylstearylammonium‐montmorillonite. The organoclays were mixed with molten B‐ala, followed by pouring into glass mold and then gradual curing up to 250°C. DSC and IR were used to follow the cure behavior of B‐ala in the presence of organoclay, indicating that organoclays catalyzed the ring opening of cyclic benzoxazine structure. The XRD of the nanocomposites showed featureless patterns, suggesting the exfoliation of the organoclay into the matrix. The viscoelastic properties of the hybrids showed that the glass transition temperatures (T_g) of the nanocomposites shifted to lower temperature in the presence of small amount of organoclay, but T_g started to increase with the increase of the organoclay content. This result suggests that, in the presence of organoclay, the curing reaction of ally and benzoxazine occurred in a different way, resulting in a different network structure. However, the presence of dispersed layered silicates into the matrix enhanced the thermal stability over the neat thermoset resin. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Influence of organic modification on mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites

The influence of organic modifiers on intercalation extent, structure, thermal and mechanical properties of poly(methyl methacrylate) (PMMA)–clay nanocomposites were studied. Two different organic modifiers with varying hydrophobicity (single tallow versus ditallow) were investigated. The nanocomposites were prepared from melt processing method and characterized using wide angle X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, differential scanning calorimetry (DSC), and tensile tests. Mechanical properties such as tensile modulus (E), break stress (σ_brk), and % break strain (ε_brk) were determined for nanocomposites at various clay loadings. Extent of PMMA intercalation is sufficient and in the range 9–15 Å depending on organoclay and filler loading. Overall thermal stability of nanocomposites increases by 16–30°C. The enhancement in T_g of nanocomposite is merely by 2–4°C. With increase in clay loading, tensile modulus increases linearly while % break strain decreases. Break stress is found to increase till 4 wt % and further decreases at higher clay loadings. The overall improvement in thermal and mechanical properties was higher for the organoclay containing organic modifier with lower hydrophobicity and single tallow amine chemical structure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

CO2 sorption and diffusion in polymethyl methacrylate–clay nanocomposites

This study reports the glass transition temperature (T_g), and sorption and diffusion of subcritical CO₂ gas in polymethyl methacrylate (PMMA) nanocomposites containing organically modified smectite clay, Cloisite 20A (C20A). A range of methods for preparing the PMMA‐clay nanocomposites was investigated and a solution coprecipitation method was selected as the most appropriate. Using this method, PMMA nanocomposite containing 2, 4, 6, and 10 wt% nanoclay loadings were prepared. Wide‐angle X‐ray diffraction (XRD) analysis and scanning electron microscopy (SEM) indicated that the 2 wt% nanocomposite materials had a well‐dispersed intercalated clay structure. The T_g for PMMA‐C20A nanocomposites, as measured by differential scanning calorimetry (DSC), was found to be independent of the clay loading. CO₂ solubility studies from 0 to 65°C and pressures up to 5.5 MPa using an in situ gravimetric technique were performed on compression‐molded films. The organoclay was found to have no effect on the solubility of CO₂ in PMMA, and therefore the solubility of CO₂ in the nanocomposite can be determined from the solubility of CO₂ in the matrix polymer alone. Diffusion coefficients were determined using the appropriate transport models for these test conditions and the diffusion coefficients for CO₂ in PMMA‐C20A composites were found to increase with organoclay loading. It is believed that the processing path taken to prepare the nanocomposites may have resulted in the agglomeration of the C20A organoclay, thereby preventing the polymer chains from fully wetting and intercalating a large number of clay particles. These agglomerations are responsible for the formation of large‐scale holes within the glassy nanocomposite, which behave as low resistance pathways for gas transport within the PMMA matrix. POLYM. ENG. SCI., 45:904–914, 2005. © 2005 Society of Plastics Engineers     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Polystyrene–organoclay nanocomposites prepared by melt intercalation,in situ,and masterbatch methods

In this study, polystyrene (PS)/montmorillonite nanocomposites were prepared by melt intercalation, in situ polymerization, and masterbatch methods. In the masterbatch method, as the first step, a high clay content composite of PS–organoclay (masterbatch) was prepared by in situ polymerization, and then the prepared masterbatch was diluted to desired compositions with commercial PS in a twin‐screw extruder. The structure and mechanical properties of the nanocomposites were examined. X‐ray diffraction (XRD) analysis showed that the d‐spacing of the in situ formed nanocomposites increased from 32.9 Å for the organoclay powder to 36.3 and 36.8 Å respectively in nanocomposites containing 0.73 and 1.6 wt% organoclay, indicating intercalation. However, the d‐spacing of the other prepared materials remained nearly unchanged when compared with pure organoclay powder. Thus, at these low clay contents, in situ formed nanocomposites showed the best improvement in mechanical properties including tensile, impact strength, and Young's modulus. In situ polymerization method did not prove to be efficient at high clay loadings in terms of intercalation and mechanical properties. At high clay loadings, the effects of the three methods in promoting mechanical properties were not significantly different from each other. POLYM. COMPOS., 27:249–255, 2006. © 2006 Society of Plastics Engineers     

Polylactide/transition metal ion modified montmorillonite nanocomposite—a critical evaluation of mechanical performance and thermal stability

Polylactide (PLA) nanocomposite was prepared by melt blending of PLA and transition metal ion (TMI) adsorbed montmorillonite (MMT). PLA nanocomposite was characterized for mechanical performance, and the results revealed that the tensile modulus, flexural modulus, and impact strength were increased marginally. The nanocomposite was optimized at 5 wt% of TMI‐modified MMT (TMI‐MMT) loading. Thermogravimetric analysis displayed increase in onset of degradation temperature, and differential scanning calorimetry showed marginal increase in glass transition temperature (T_g) and melting temperature (T_m) in case of PLA nanocomposites, when compared with virgin PLA. The flammability testing of nanocomposites indicated good fire retardance characters. X‐ray diffraction patterns of TMI‐MMT and the corresponding nanocomposites indicated an intercalation of the metal ions into the clay interlayer. Fourier transform infrared spectroscopy analysis indicate formation of [Zn(EDA)₂]²⁺ and [Cu(EDA)₂]²⁺ complexes in the MMT interlayer. Dynamic mechanical analysis shows increase in glass transition temperature (T_g) and storage modulus (E′) in case of PLA nanocomposites reinforced with 5 wt% modified MMT. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Development of high‐performance epoxy/clay nanocomposites by incorporating novel phosphonium modified montmorillonite

Novel organoclays were synthesized by several kinds of phosphonium cations to improve the dispersibility in matrix resin of composites and accelerate the curing of matrix resin. The possibility of the application for epoxy/clay nanocomposites and the thermal, mechanical, and adhesive properties were investigated. Furthermore, the structures and morphologies of the epoxy/clay nanocomposites were evaluated by transmission electron microscopy. Consequently, the corporation of organoclays with different types of phosphonium cations into the epoxy matrix led to different morphologies of the organoclay particles, and then the distribution changes of silicate layers in the epoxy resin influenced the physical properties of the nanocomposites. When high‐reactive phosphonium cations with epoxy groups were adopted, the clay particles were well exfoliated and dispersed. The epoxy/clay nanocomposite realized the high glass‐transition temperature (T_g) and low coefficient of thermal expansion (CTE) in comparison with those of neat epoxy resin. On the other hand, in the case of low‐reactive phoshonium cations, the dispersion states of clay particles were intercalated but not exfoliated. The intercalated clay did not influence the T_g and CTE of the nanocomposite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The toughening effect and mechanism of styrene‐butadiene rubber nanoparticles for novolac resin

In this article, phenolic nanocomposites were prepared using styrene–butadiene rubber (SBR) nanoparticles with an average particle size of about 60 nm as the toughening agent. The mechanical and thermal properties of phenolic nanocomposites and the toughening mechanism were studied thoroughly. The results showed that when adding 2.5 wt % SBR nanoparticles, the notched impact strength of phenolic nanocomposites reached the maximum value and was increased by 52%, without sacrificing the flexural performance. Meanwhile, SBR nanoparticles had no significant effect on the thermal decomposition temperature of phenolic nanocomposites. The glass‐transition temperature (T_g) of phenolic nanocomposites shifted to a lower temperature accompanying with the increasing T_g of loaded SBR, which showed there was a certain compatibility between SBR nanoparticles and phenol‐formaldehyde resin (PF). Furthermore, the analysis of Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy indicated that there existed a weak chemical interaction between SBR nanoparticles and the PF matrix. The certain compatibility and weak chemical interaction promoted the formation of a transition layer and improved the interfacial bonding, which might be important reasons for the great enhancement of the toughness for phenolic nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41533.     

Polymerization compounding: Epoxy‐montmorillonite nanocomposites

A strategy to design intercalated montmorillonite nanocomposites has been explored. A commercial organoclay, 1.34 TCN (Nanocor Inc.), with bis(2‐hydroxylethy1) methy1 tallow ammonium, was modified by tolylene 2,4‐diisocyanate (TDI) and bisphenol A (BA). Thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) results of unmodified and modified 1.34 TCN (1.34‐TDI‐BA) indicate that TDI and BA have reacted with hydroxy1 groups on the surface of 1.34 TCN and hydroxy1 groups in the interlayer of 1.34 TCN. Using a classical two‐stage cure process with diamine as curing agent, intercalated epoxy nanocomposites were prepared for both types of organoclays. XRD and TEM results showed that the basal spacing of clay in nanocomposites was 3.68 and 4.42 nm for 1.34 TCN and 1.34‐TDI‐BA, respectively. Dynamic mechanical analysis (DMA) was performed on both modified and unmodified organoclay composites. Modified organoclay composites were found to have enhanced storage moduli, particularly at temperatures higher than the glass transition, T_g, of the matrix. Glass transition temperatures extracted from linear viscoelastic data are found to be slightly higher for modified organoclay nanocomposites, indicating enhanced interactions between the modified organoclay and the epoxy matrix. These results were also confirmed by independent measurements of T_g using differential scanning calorimetry (DSC).     

Photopolymerization and characteristics of reactive organoclay–polyurethane nanocomposites

Polymerizable ammonium surfactants with two methacrylate alkyl chains were successfully synthesized via Michael‐Addition and quaternization reaction. Organoclays containing reactive methacrylate groups were prepared by cationic exchange process. Intercalated nanocomposites have been produced by UV initiated polymerization with different organophilic clay loading. X‐ray diffraction (XRD) spectroscopy showed that the d spacing of organoclay increased with increment of methacrylate alkyl chains length. When organoclay were dispersed in urethane acrylate resin, and photopolymerized, the d spacing increased, but the increasing extent decreased with increment of the methacrylate alky chains length. Thermogravimetric analysis indicated that incorporation of reactive organoclay had better thermal stablity than cetyltrimethylammonium bromide (CTMA)‐modified organoclay and dynamic mechanical analysis (DMA) showed nanocomposites containing reactive organoclay had high glass transition temperature and storage modulus. Tensile analysis implied that incorporation of reactive organoclay could enhance mechanical and tensile properties dramatically. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Effect of organoclay reinforcement on the curing characteristics and technological properties of SBR sulphur vulcanizates

Styrene‐butadiene rubber (SBR) nanocomposites with different organoclay contents (up to 15 phr) were prepared by a melt compounding procedure, followed by a compression‐molding step in which the SBR matrix was sulfur crosslinked. The vulcanizates were characterized in respect to their curing, mechanical and viscoelastic properties, and thermal stability. The optimum cure time decreased with increasing organoclay content. This effect was attributed to the ammonium modifier present in the organoclay, which takes part in the curing reaction acting like an accelerator. The results of mechanical test on the vulcanizates showed that the nanocomposites presented better mechanical properties than unfilled SBR vulcanizate, indicating the nanoreinforcement effect of clay on the mechanical properties of SBR/organoclay nanocomposites. The addition of organoclay did not significantly change the glass transition temperature. However, the heights of tan δ value at the glass transition temperature for the nanocomposites are lower than that of the unfilled SBR. This suggests a strong interaction between the organoclay and the SBR matrix as the molecular relaxation of the latter is hampered. The temperature at which 50% degradation occurs (T₅₀) and the temperature when the degradation rate is maximum (DTG_max) showed an improvement in thermal stability, probably related to the uniform dispersion of organoclay. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010