Optically active Er–Yb codoped Y2O3 films produced by pulsed laser deposition

Optically active Er³⁺:Yb³⁺ codoped Y₂O₃ films have been produced on c-cut sapphire substrates by pulsed laser deposition from ceramic Er:Yb:Y₂O₃ targets having different rare-earth concentrations. Stoichiometic films with very high rare-earth concentrations (up to 5.5 × 10²¹ at cm^− 3) have been achieved by using a low oxygen pressure (1 Pa) during deposition whereas higher pressures lead to films having excess of oxygen. The crystalline structure of such stoichiometric films was found to worsen the thicker the films are. Their luminescence at 1.53 μm and up-conversion effects have been studied by pumping the Yb³⁺ at 0.974 μm. The highest lifetime value (up to 4.6 ms) is achieved in films having Er concentrations of ≈ 3.5 × 10²⁰ at cm^− 3 and total rare-earth concentration ≈ 1.8 × 10²¹ at cm^− 3. All the stoichiometric films irrespective of their rare-earth concentration or crystalline quality have shown no significant up-conversion.     

Structural, electrical and optical characteristics of SnO2:Sb thin films by ultrasonic spray pyrolysis

Antimony-doped tin oxide (SnO₂:Sb) thin films were fabricated by an ultrasonic spray pyrolysis method. The effect of antimony doping on the structural, electrical and optical properties of tin oxide thin films were investigated. Tin(II) chloride dehydrate (SnCl₂·2H₂O) and antimony(III) chloride (SbCl₃) were used as a host and a dopant precursor. X-ray diffraction analysis showed that the non-doped SnO₂ thin film had a preferred (211) orientation, but as the Sb-doping concentration increased, a preferred (200) orientation was observed. Scanning electron microscopy studies indicated that the polyhedron-like grains observed for the non-doped SnO₂ thin films became rounder and decreased in size with the Sb-doping concentration. The lowest resistivity (about 8.4 × 10^− 4 Ω·cm) was obtained for the 3 at.% Sb-doped films. Antimony-doping led to an increase in the carrier concentration and a decrease in Hall mobility. The transmittance level in the near infrared region was lowered with the Sb-doping concentration.     

Highly conducting indium tin oxide (ITO) thin films deposited by pulsed laser ablation

Highly conducting and transparent indium tin oxide (ITO) thin films were prepared on SiO₂ glass and silicon substrates by pulsed laser ablation (PLA) from a 90 wt.% In₂O₃-10 wt.% SnO₂ sintered ceramic target. The growths of ITO films under different oxygen pressures (P_O2) ranging from 1×10⁻⁴–5×10⁻² Torr at low substrate temperatures (T_s) between room temperature (RT) and 200°C were investigated. The opto-electrical properties of the films were found to be strongly dependent on the P_O2 during the film deposition. Under a P_O2 of 1×10⁻² Torr, ITO films with low resistivity of 5.35×10⁻⁴ and 1.75×10⁻⁴ Ω cm were obtained at RT (25°C) and 200°C, respectively. The films exhibited high carrier density and reasonably high Hall mobility at the optimal P_O2 region of 1×10⁻² to 1.5×10⁻² Torr. Optical transmittance in excess of 87% in the visible region of the solar spectrum was displayed by the films deposited at Po₂≥1×10⁻² Torr and it was significantly reduced as the P_O2 decreases.     

New transparent conducting MgIn2O4---Zn2In2O5 thin films prepared by magnetron sputtering

New materials for a transparent conducting oxide film are demonstrated. Highly transparent Zn₂In₂O₅ films with a resistivity of 3.9 × 10⁻⁴ Ω cm were prepared on substrates at room temperature using a pseudobinary compound powder target composed of ZnO (50 mol.%) and In₂O₃ (50 mol.%) by r.f. magnetron sputtering. MgIn₂O₄---Zn₂In₂O₅ films were prepared using MgIn₂O₄ targets with a ZnO content of 0–100 wt.%. The resistivity of the deposited films gradually decreased from 2 × 10⁻³ to 3.9 × 10⁻⁴ Ω cm as the Zn/(Mg + Zn) atomic ratio introduced into the films was increased. The greatest transparency was obtained in a MgIn₂O₄ film. The optical absorption edge of the films decreased as the Zn/(Mg + Zn) atomic ratio was increased, corresponding to the bandgap energy of their materials. It was found that the resistance of the undoped Zn₂In₂O₅ films was more stable than either the undoped MgIn₂O₄, ZnO or In₂O₃ films in oxidizing environments at high temperatures.     

Infrared optical properties of Bi2Ti2O7 thin films by spectroscopic ellipsometry

Bi₂Ti₂O₇ thin films have been grown directly on n-type GaAs (1 0 0) by the chemical solution decomposition technique. X-ray diffraction analysis shows that the Bi₂Ti₂O₇ thin films are polycrystalline. The optical properties of the thin films are investigated using infrared spectroscopic ellipsometry (3.0–12.5 μm). By fitting the measured ellipsometric parameter (Ψ and Δ) data with a three-phase model (air/Bi₂Ti₂O₇/GaAs), and Lorentz–Drude dispersion relation, the optical constants and thickness of the thin films have been obtained simultaneously. The refractive index and extinction coefficient increase with increasing wavelength. The fitted plasma frequency ω_p is 1.64×10¹⁴ Hz, and the electron collision frequency γ is 1.05×10¹⁴ Hz, and it states that the electron average scattering time is 0.95×10⁻¹⁴ s. The absorption coefficient variation with respect to increasing wavelength has been obtained.     

Semiconducting and structural properties of CrSi2 A-type epitaxial films on Si(111)

Chromium disilicide (CrSi₂) films 1 000 Å thick have been prepared by molecular beam epitaxy on CrSi₂ templates grown on Si(111) substrate. The effect of the substrate temperature on the structural, electrical and optical properties of CrSi₂ films has been studied by transmission and scanning electron microscopies, optical microscopy, electrical resistivity and Hall effect measurements and infrared optical spectrometry. The optimal temperature for the formation of the epitaxial A-type CrSi₂ film have been found to be about 750°C. The electrical measurement have shown that the epitaxial A-type CrSi₂ film is p-type semiconductor having a hole concentration of 1 × 10¹⁷cm⁻³ and Hall mobility of 2 980 cm² V⁻¹ s⁻¹ at room temperature. Optical absorption coefficient data have indicated a minimum, direct energy gap of 0.34 eV. The temperature dependence of the Hall mobility (μ) in the temperature range of T = 180–500 K can be expressed as μ = 7.8 × 10¹⁰T⁻³cm²V⁻¹s⁻¹.     

Structure and electrical properties of (100)-oriented Pb(Zn1/3Nb2/3)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 thin films on La0.7Sr0.3MnO3 electrode by chemical solution deposition

(100)-oriented 0.462Pb(Zn_1/3Nb_2/3)O₃–0.308Pb(Mg_1/3Nb_2/3)O₃–0.23PbTiO₃ (PZN-PMN-PT) perovskite ferroelectric thin films were prepared on La_0.7Sr_0.3MnO₃/LaAlO₃ (LSMO/LAO) substrate via a chemical solution deposition route. The perovskite LSMO electrode was found to effectively suppress the pyrochlore phase while promote the growth of the perovskite phase in the PZN-PMN-PT film. The film annealed at 700 °C exhibited a high dielectric constant of 2130 at 1 kHz, a remnant polarization, 2P_r, of 29.8 μC/cm², and a low leakage current density of 7.2 × 10^− 7 A/cm² at an applied field of 200 kV/cm. The ferroelectric polarization was fatigue-free at least up to 10¹⁰ cycles. Piezoelectric coefficient, d₃₃, of 48 pm/V was also demonstrated. The results showed that much superior properties could be achieved with the PZN-PMN-PT thin films on the solution derived LSMO electrode than on Pt electrode by sputtering.     

Al2O3 formation on Si by catalytic chemical vapor deposition

Catalytic chemical vapor deposition (Cat-CVD) has been developed to deposit alumina (Al₂O₃) thin films on silicon (Si) crystals using N₂ bubbled tri-methyl aluminum [Al(CH₃)₃, TMA] and molecular oxygen (O₂) as source species and tungsten wires as a catalyzer. The catalyzer dissociated TMA at approximately 600 °C. The maximum deposition rate was 18 nm min⁻¹ at a catalyzer temperature of 1000 °C and substrate temperature of 800 °C. Metal oxide semiconductor (MOS) diodes were fabricated using gates composed of 32.5-nm-thick alumina film deposited at a substrate temperature of 400 °C. The capacitance measurements resulted in a relative dielectric constant of 7.4, fixed charge density of 1.74×10¹² cm⁻², small hysteresis voltage of 0.12 V, and very few interface trapping charges. The leakage current was 5.01×10⁻⁷ A cm⁻² at a gate bias of 1 V.     

The optical and electrical properties of copper indium di-selenide thin films

Thin films of copper indium di-selenide (CIS) with a wide range of compositions near stoichiometry have been formed on glass substrates in vacuum by the stacked elemental layer (SEL) deposition technique. The compositional and optical properties of the films have been measured by proton-induced X-ray emission (PIXE) and spectrophotometry (photon wavelength range of 300–2500 nm), respectively. Electrical conductivity (σ), charge-carrier concentration (n), and Hall mobility (μ_H) were measured at temperatures ranging from 143 to 400 K. It was found that more indium-rich films have higher energy gaps than less indium-rich ones while more Cu-rich films have lower energy gaps than less Cu-rich films. The sub-bandgap absorption of photons is minimum in the samples having Cu/In ≈ 1 and it again decreases, as Cu/In ratio becomes less than 0.60. Indium-rich films show n-type conductivities while near-stoichiometric and copper-rich films have p-type conductivities. At 300 K σ, n and μ_H of the films vary from 2.15 × 10⁻³ to 1.60 × 10⁻¹ (Ω cm)⁻¹, 2.28 × 10¹⁵ to 5.74 × 10¹⁷ cm⁻³ and 1.74 to 5.88 cm² (V s)⁻¹, respectively, and are dependent on the composition of the films. All the films were found to be non-degenerate. The ionization energies for acceptors and donors vary between 12 and 24, and 3 and 8 meV, respectively, and they are correlated well with the Cu/In ratios. The crystallites of the films were found to be partially depleted in charge carriers.     

Structure-composition-property dependence in reactive magnetron sputtered ZnO thin films

Thin films of zinc oxide (ZnO) were prepared by dc reactive magnetron sputtering on glass substrates at various oxygen partial pressures in the range 1×10⁻⁴–6×10⁻³ mbar and substrate temperatures in the range 548–723 K. The variation of cathode potential of zinc target on the oxygen partial pressure was explained in terms of target poisoning effects. The stoichiometry of the films has improved with the increase in the oxygen partial pressure. The films were polycrystalline with wurtzite structure. The films formed at higher substrate temperatures were (0 0 2) oriented. The temperature dependence of Hall mobility of the films formed at various substrate temperatures indicated that the grain boundary scattering of charge carriers was predominant electrical conduction mechanism in these films. The optical band gap of the films increased with the increase of substrate temperature. The ZnO films formed under optimized oxygen partial pressure of 1×10⁻³ mbar and substrate temperature of 663 K exhibited low electrical resistivity of 6.9×10⁻² Ω cm, high visible optical transmittance of 83%, optical band gap of 3.28 eV and a figure of merit of 78 Ω⁻¹ cm⁻¹.     

Implantation effect of diamond-like carbon films by 110 keV nitrogen ions

Diamond-like carbon films, grown on microscope slides by a dual-ion beam sputtering system, were implanted by 110 keV N⁺ under the doses of 1 × 10¹⁵, 1 × 10¹⁶ and 1 × 10¹⁷ions cm⁻² respectively. The implantation induced changes in electrical resistivity of the films and in infrared (IR) transmittance of the specimens were investigated as a function of implantation dose. The structural changes of the films were also studied using IR spectroscopy and Raman spectroscopy. It was observed that, with the increase of implantation dose, the diamond-like carbon films display two different stages in electrical and optical behaviours. The first is the increase of both the film resistivity and the IR transmittance of specimen at the dose of 1 × 10¹⁵ ions cm⁻² which, we consider, is attributed to the implantation-induced increase sp³ C---H bonds. However, when the doses are higher than 1 × 10¹⁵ ions cm⁻², the film resistivity and the IR transmittance of specimen decrea significantly and the decrease rates at dose range of 1×10¹⁶ to 1×10¹⁷ ions cm⁻² are smaller than those between 1×10¹⁵ and 1 × 10¹⁶ ions cm⁻². We conclude that the significant reductions of the two parameters at high doses are caused by the decreases of bond-angle disorder and of sp³ C---H bonds, the increases of sp² C---C bonds dominated the crystallite size and/or number and also the sp² C---H bonds. The smaller decrease rates at a dose range of 1 × 10¹⁶ to 1 × 10¹⁷ ions cm⁻² may be caused by further recombination of some retained hydrogen atoms to carbon atoms.     

Atomic layer deposition growth of zirconium doped In2O3 films

Zirconium doped indium oxide thin films were deposited by the atomic layer deposition technique at 500 °C using InCl₃, ZrCl₄ and water as precursors. The films were characterised by X-ray diffraction, energy dispersive X-ray analysis and by optical and electrical measurements. The films had polycrystalline In₂O₃ structure. High transparency and resistivity of 3.7×10⁻⁴ Ω cm were obtained.     

Improved tribological properties of sputtered MoS2 films through N implantation

The effect of N⁺ implantation on the microstructural and tribological properties of r.f.-sputtered MoS₂ films was studied. The cross-section scanning electron micrographs show that, after N⁺ implantation, the loose column structure of the sputtered MoS₂ films increases in density. A decrease in film thickness of about 50% is also observed. The results of X-ray diffraction analysis show that N⁺ bombardment enhances the (100) edge plane orientation of the MoS₂ crystal in the film. The scratch test indicates an improved film-substrate adherence. The tribological test results indicate that N⁺ implantation yields a distinct enhancement in the wear life of the sputtered MoS₂ films. Compared with the as-deposited MoS₂ film, the wear life of the sputtered MoS₂ films implanted with 150 keV N⁺ at 1 × 10¹⁶ N⁺ cm⁻² shows a threefold increase in a relative humidity of 60%–70% and a twofold increase in a vacuum of 5 × 10⁻³ Pa. However, N⁺ implantation inreases the friction coefficient. The lubrication model of the N⁺-modified film is given.     

High polysilicon TFT field effect mobility reached thanks to slight phosphorus content in the active layer

The paper deals with the effect of slightly phosphorus atoms introduced during deposition of polysilicon films. Polysilicon films are used as an active layer in thin film transistors (TFTs) fabricated on glass substrates at a maximum temperature of 600 °C.Three phosphorus atoms contents, determined by the value of the phosphine to silane ratio: Γ (3.7 × 10^− 7, 8 × 10^− 7, 26 × 10^− 6), are used to optimize the active layer quality. The in-situ doped layers induce a better stability of the electrical characteristics, a higher mobility and lower value of the threshold voltage for the slightly doped active layers [M. Zaghdoudi, M.M. Abdelkrim, M. Fathallah, T. Mohammed-Brahim and F. Le-Bihan Control of the weak phosphorus doping in polysilicon, Materials Science and Forum, Vols. 480–481 (2005) pp.305.]. The present work shows that the effect of slightly phosphorus content improves the quality of oxide/polysilicon interface and decreases the defects density. Degradation of electrical properties is shown to originate from the creation of defect at the channel-interface oxide and in the grain boundaries. The effect of temperature change on the electrical properties was studied and the behaviour was also analyzed.     

(Fe,Ti) 16N2 films with high saturation magnetization prepared by facing target sputtering

(Fe,Ti)-N films with a Ti concentration of 10 at.% were prepared on Si(100) and NaCl substrates by facing targets sputtering. The effects of the nitrogen pressure (P_N) and the substrate temperature (T_s) on the formation of various (Fe,Ti)-N phases and their microstructures were investigated in detail. X-ray diffractometer and transmission electron microscope provided complete identification of the phases present in the films and the characterization of their microstructures. Films deposited at a lower P_N = 1 3 × 10⁻² Pa or a lower T_s = RT consist of mainly -phase. Films deposited at a higher P_N = 1.3 2 × 10⁻¹ Pa or a higher T_s = 200 °C contain a great many γ' and Fe₂N phases with a higher nitrogen content. When P_N = 4 7 × 10⁻² Pa and T_s = 100 150 °C, it is advantageous to the formation of ′' phase. These films exhibit a high saturation magnetization (M_s) up to the range of 2.3 2.5 T, which is larger than that of pure iron.     

Photoluminescence of Ga0.94In0.06As0.13Sb0.87 solid solution lattice matched to InAs

The lattice matched Ga_0.94In_0.06As_0.13Sb_0.87 quaternary solid solutions were grown by liquid phase epitaxy on (1 0 0) oriented InAs substrates from In rich melt. The p-type GaIn_0.06As_0.13Sb layers were intentionally undoped and their hole concentration was about p5×10¹⁶ cm⁻³, while n-type GaIn_0.06As_0.13Sb layers were slightly doped with Te and their electron concentration was about n10¹⁷ cm⁻³. Photoluminescence spectra exhibit single unresolved emission band in the spectral region from 0.65 to 0.8 eV for both types. Spectra were decomposed to elementary Gaussian components. The main mechanisms of radiative recombination were determined for both types of material.     

Preparation and characterization of Bi2Ti2O7 thin films by chemical solution deposition technique

Transparent and crack-free Bi₂Ti₂O₇ thin films with strong (111) orientation were successfully prepared on n-Si(100) by chemical solution deposition (CSD) using bismuth nitrate and titanium butoxide as starting materials. The structural properties were studied by X-ray diffraction. The dielectric constant at 100 kHz at room temperature was 118 and loss factor was 0.074, for a 0.4-μm-thick film annealed at 500°C for 30 min. The leakage current density was 4.06×10⁻⁷ A/cm² at an applied voltage of 15 V.     

The effect of the isopoly tungstate anion on the composition and conductivity of polypyrrole composite films

The polypyrrole composite films were prepared by the electropolymerization of pyrrole from the aqueous solution containing isopoly tungstate (poly-W) and the chloride anion (Cl⁻) at various ratios. The film formation was traced by electrochemical quartz crystal microbalance, and the tungsten concentrations in the films were measured by the inductively coupled plasma spectroscopy. The electric conductivities of the films were measured by the four-point probe method. In the ratio of poly-W concentration to Cl⁻ concentration, ((poly-W)/Cl⁻)), higher than 1.26 × 10⁻² in the solution the concentration of tungsten in the films showed a constant value at 51 wt.% and the chloride anion was not included in the film. The conductivities of these films showed the constant value about 40 S cm⁻¹. In the ratio lower than (poly-W)/(Cl⁻) = 1.26 × 10⁻², the conductivity decreased with the decrease of poly-W concentration and the composite films consisted of two layers; the inner layer initially formed contained larger amount of tungsten than that of the outer layer.     

Characterization of indium zinc oxide thin films prepared by pulsed laser deposition using a Zn3In2O6 target

Using a Zn₃In₂O₆ target, indium-zinc oxide films were prepared by pulsed laser deposition. The influence of the substrate deposition temperature and the oxygen pressure on the structure, optical and electrical properties were studied. Crystalline films are obtained for substrate temperatures above 200°C. At the optimum substrate deposition temperature of 500°C and the optimum oxygen pressure of 10⁻³ mbar, both conditions that indeed lead to the highest conductivity, Zn₃In₂O₆ films exhibit a transparency of 85% in the visible region and a conductivity of 1000 S/cm. Depositions carried out in oxygen and reducing gas, 93% Ar/7% H₂, result in large discrepancies between the target stoichiometry and the film composition. The Zn/In (at.%) ratio of 1.5 is only preserved for oxygen pressures of 10⁻²–10⁻³ mbar and a 93% Ar/7% H₂ pressure of 10⁻² mbar. The optical properties are basically not affected by the type of atmosphere used during the film deposition, unlike the conductivity which significantly increases from 80 to 1400 S/cm for a film deposited in 10⁻² mbar of O₂ and in 93% Ar/7% H₂, respectively.     

Influence of conventional furnace and rapid thermal annealing on the quality of polycrystalline β-FeSi2 thin films grown from vapor-deposited Fe/Si multilayers

Thin films of polycrystalline β-FeSi₂ were grown on (100) Si substrates of high resistivity by electron beam evaporation of Si/Fe ultrathin multilayers and subsequent annealing by conventional vacuum furnace (CVF) and rapid thermal annealing (RTA) for 1 h and 30 s, respectively, in the temperature range from 600 to 900°C. X-ray diffraction, Raman spectroscopy, spectroscopic ellipsometry, resistivity and Hall measurements were employed for characterization of the silicide layers quality in terms of the annealing conditions. For the silicide layers prepared by CVF annealing, although the grain size increase with increasing the annealing temperature, the optimum temperature to obtain the higher material quality (carrier mobility of the order of 100 cm² Vs⁻¹ and carrier concentration of about 1 × 10¹⁷ cm⁻³) is about 700°C. At higher annealing temperatures, the quality of the material is degraded due to the presence of the oxide Fe₂O₃. In the case of the silicides prepared by RTA, the quality of the material is improved progressively with increasing the annealing temperature up to 900°C.