Investigating the need of a pre-concentrator column for acetic acid dehydration system via heterogeneous azeotropic distillation

In our previous study [Chien, I.L., Zeng, K.L., Chao, H.Y., Liu, J.H. (2004). Design and control of acetic acid dehydration system via heterogeneous azeotropic distillation. Chemical Engineering Science 59(21), 4547-4567.], an acetic acid dehydration system has been designed. The suitable entrainer selected for that system is iso-butyl acetate. Design and control of the system has been studied in detail to maintain high-purity bottom acetic acid concentration and also keep a small acetic acid loss through top aqueous draw. In that previous study, the feed composition is assumed to contain equal molar of acetic acid and water. However, in a typical waste acid recovery application, the above assumption may be too rich in acetic acid. In this paper, a feed stream containing 80 mol% water and 20 mol% of acetic acid is investigated. Several design alternatives can be deduced including one commonly used in industry by adding a pre-concentrator column in the upstream of a heterogeneous azeotropic distillation column. The necessity of this pre-concentrator column from design and control view points will be thoroughly investigated in this paper. The final recommended process design is a tradeoff between total annual cost (TAC) and operability of the system. The recommended design is a single heterogeneous azeotropic distillation column with aqueous reflux stream. Very wide feed composition and flow rate changes can be handled by this design with proper choice of the overall control strategy.     

Design and control of acetic acid dehydration system via heterogeneous azeotropic distillation

Acetic acid dehydration is an important operation in the production of aromatic acid, such as terephthalic acid or in the manufacture of cellulose acetate. Although acetic acid and water does not form azeotrope, but using simple distillation to separate these two components is not practical. The reason is because the system has tangent pinch on the pure water end, thus it is more customary in industry to use an entrainer via a heterogeneous azeotropic distillation column system for the separation. In this study, a suitable entrainer is selected from three candidate acetates through rigorous steady-state simulation of this system. Optimum process design and operating condition are determined to keep high-purity bottom acetic acid composition and also keep a small acetic acid loss through top aqueous draw. Furthermore, the overall control strategy of this column system is proposed to hold both bottom and top product specifications in spite of feed rate and feed composition load disturbances. The proposed overall control strategy is very simple requiring only one tray temperature control loop inside the heterogeneous azeotropic column.     

间歇共沸精馏分离乙醇一水体系的改进研究

间歇共沸精馏是分离共沸物的一种方法,适用于化工、制药、溶剂回收、天然产物提取等产量小、品种多的行业,因此间歇共沸精馏近年来已成为非常活跃的研究和开发热点.对已有的常规间歇共沸精馏的操作方式作了改进,即共沸剂改为在塔釜回流,以正己烷为共沸剂,对分离乙醇-水共沸体系进行了改进研究,并与常规间歇共沸精馏的实验结果进行比较.结...     

Separation of ethyl acetate–isooctane mixture by heteroazeotropic batch distillation

This paper studies the separation of an ethyl acetate–isooctane mixture by heterogeneous azeotropic distillation in a batch rectifying column. An initial list of 60 candidates was studied but only methanol and acetonitrile were obtained as potential heterogeneous entrainers. These entrainers form a low boiling heterogeneous azeotrope with isooctane. Experimental verification of the miscibility gap with isooctane was performed at 25 °C for each entrainer giving a smaller region for methanol than for acetonitrile. Feasibility of the heterogeneous azeotropic batch distillation was carried out experimentally in a laboratory batch distillation column having 44 theoretical equilibrium stages and using a high reflux ratio. Several distillate fractions were taken as a function of the temperature at the top of the column. For both methanol and acetonitrile, the main fraction was defined by the condensed vapor providing a liquid–liquid split of the isooctane/entrainer heteroazeotrope into the decanter. Ethyl acetate impurity was detected in both decanted phases, but in much lower amount when using acetonitrile as entrainer. The process with acetonitrile also resulted in a shorter operating time and higher purity and recovery yield of isooctane as the main distillate product. Pure ethyl acetate remained into the boiler at the end of each process.     

Synthesis,experiments and simulation of heterogeneous batch distillation processes

The presence of azeotropes in multicomponent mixtures complicates the design of batch distillation separation processes widely used in pharmaceutical and speciality chemical industries. Most of those processes include the use of a homogeneous entrainer to ease the separation. We describe novel methods to break azeotropes using an entrainer that is partially miscible with one of the initial binary mixture components. We depict some of the advantages of heterogeneous batch distillation processes: more design alternatives for the separation of an azeotropic binary mixture than with homogeneous batch distillation, batch distillation boundary crossing thanks to a controlled reflux of the entrainer-rich phase, simplified distillation sequences as a consequence of less distillation tasks. Three examples based on the separation of non-ideal azeotropic or close boiling point binary mixtures through heterogeneous batch distillation are simulated using a commercial batch distillation package. Experiments validate the simulated separation of a minimum boiling azeotropic mixture.     

工业醋酸脱水过程五元体系非均相共沸精馏的流程模拟

针对以醋酸正丙酯为共沸剂的醋酸脱水过程,考虑醋酸溶剂中未反应的前体对二甲苯以及反应的副产物醋酸甲酯的影响及回收利用,分别选用HOC和UNIQUAC模型来修正体系中五元混合物系的汽液非理想性,通过拟合醋酸甲酯-对二甲苯和醋酸正丙酯-对二甲苯两体系的二元汽液平衡实验数据获得了该两组体系UNIQUAC模型的二元交互作用参数,借助模拟软件Aspen Plus,结合软件内置其他二元体系参数,对工业醋酸脱水塔系包括溶剂脱水塔、PX回收塔、共沸剂回收塔在内的三塔体系进行系统的分析模拟,得到了与工艺数据误差小于±6%的能正确描述工业醋酸脱水塔系操作特性的工艺机理稳态模型,为工业醋酸脱水过程工艺的进一步研究提供理论基础和依据。     

共沸蒸馏在化工生产中的应用与研究进展

共沸蒸馏为共沸物或相对挥发度接近于1的非理想物系的分离过程提供了选择。介绍了蒸馏残余曲线图的热力学原理,并以反应蒸馏生产乙酸乙酯工艺为例说明了蒸馏残余曲线图在流程设计等方面的应用。分别从夹带剂选择、过程设计、过程集成强化、过程控制等角度阐述了共沸蒸馏过程相关理论研究进展;在应用方面,主要综述了乙醇、异丙醇稀溶液、稀乙酸等脱水及回收利用情况,共沸蒸馏过程强化反应蒸馏、变压共沸蒸馏、共沸蒸馏耦合膜分离研究进展情况以及反应蒸馏工艺的局限性,并对其未来的发展前景作了展望。     

Feasibility of heterogeneous batch distillation processes

Synthesis of heterogeneous batch distillation is discussed, which aims at splitting azeotropic mixtures by adding an entrainer partially miscible with one of the initial binary mixture components. Key operational parameters are identified such as the amount of entrainer added in the ternary feed, the reflux policy, and the vapor line position by examples. Synthesis and operation are less straightforward for heterogeneous batch distillation than those for the homogeneous case, but offer many advantages: more design alternatives, simplified distillation sequences, a lower consumption of entrainer, and a crossing of distillation boundaries by the still path. Feasibility is assessed using simplified modeling and confirmed using a commercial batch process simulator package. Synthesis expectations and simulated results are verified throughout bench-plant experiments for the separation of the acetonitrile—water mixture using acrylonitrile as a light heterogeneous entrainer.     

间歇共沸精馏分离乙二醇单甲醚-水物系

通过绘制乙二醇单甲醚-水-共沸剂的简捷剩余曲线,提出了以乙酸异丙酯作为间歇共沸精馏法分离乙二醇单甲醚-水物系的共沸剂。然后完成剩余曲线数据的测定实验,根据实验数据绘制乙二醇单甲醚-水-乙酸异丙酯三元物系的剩余曲线图,确定了乙二醇单甲醚-水共沸物系的分离工艺。并通过实验研究了共沸剂加入量对乙二醇单甲醚回收率的影响,从而确定了适宜的共沸剂配比：当共沸剂与原料中水的质量比为2～2.5时,乙二醇单甲醚的一次性收率在90%以上。     

Heterogeneous extractive batch distillation of chloroform-methanol-water: Feasibility and experiments

A novel heterogeneous extractive distillation process is considered for separating the azeotropic mixture chloroform-methanol in a batch rectifying column, including for the first time an experimental validation of the process. Heterogeneous heavy entrainer water is selected inducing an unstable ternary heteroazeotrope and a saddle binary heteroazeotrope with chloroform (ternary diagram class 2.1-2b). Unlike the well-known heterogeneous azeotropic distillation process and thanks to continuous water feeding at the column top, the saddle binary heteroazeotrope chloroform-water is obtained at the column top, condensed and further split into the liquid-liquid decanter where the chloroform-rich phase is drawn as distillate. First, feasibility analysis is carried out by using a simplified differential model in the extractive section for determining the proper range of the entrainer flowrate and the reflux ratio. The operating conditions and reflux policy are validated by rigorous simulation with ProSim Batch Column^® where technical features of a bench scale distillation column have been described. Six reproducible experiments are run in the bench scale column matching the simulated operating conditions with two sequentially increasing reflux ratio values. Simulation and experiments agree well. With an average molar purity higher than 99%, more than 85% of recovery yield was obtained for chloroform and methanol.     

Design of entrainer-enhanced reactive distillation for the synthesis of butyl cellosolve acetate

An innovative entrainer-enhanced reactive distillation (RD) process is presented, which aims to the production of high-purity butyl cellosolve acetate from butyl cellosolve and acetic acid via an esterification reaction. This entrainer-enhanced RD process can procure technical advantages from both heterogeneous azeotropic distillation and RD. Solvents such as cyclohexane, ethylene dichloride, toluene, and octane are considered as candidates in this esterification RD process. The function of entrainers is to simplify the separation between water and acetic acid. For this purpose, the proper entrainer to use is thus evaluated based on its mutual solubility with water in two liquid phases. Simulation results reveal that total annual cost can be substantially reduced when cyclohexane, toluene, and octane are used as entrainers in the RD column. The octane-enhanced RD provides the most economical design in this studied case.     

共沸精馏分离乙醇-异丙醇

为了分离乙醇-异丙醇混合物,研究了共沸精馏在乙醇-异丙醇物系中的应用。根据共沸剂的选取原则选定出1-己烯作为共沸精馏分离乙醇-异丙醇混合物的共沸剂,使用ASPEN模拟软件模拟连续和间歇共沸精馏分离乙醇-异丙醇工艺流程,并通过间歇共沸精馏实验考察了所选共沸剂的分离效果。结果表明：使用1-己烯作为共沸剂能成功的分离乙醇-异丙醇混合物;采用有30块理论板的填料塔,回流比为25,共沸剂1-己烯与乙醇的质量比为4∶1,塔釜异丙醇的质量分数达到99.77%。     

Optimal design of mixed acid esterification and isopropanol dehydration systems via incorporation of dividing-wall columns

This study explores the design of a reactive distillation system and that of a heterogeneous azeotropic system by incorporating dividing-wall column (DWC). The first system involves the esterification of mixed acid (acetic acid and propionic acid) with methanol. Simulation studies are carried out for conventional reactive distillation sequence as well as for reactive dividing-wall distillation system. Both systems are optimized by an iterative optimization procedure. Optimal design results show that the reactive dividing-wall system saves steam consumption by 45.2% and reduces total annual costs (TAC) by 34.5%. The second case investigated is a heterogeneous azeotropic distillation system involving dehydration of crude isopropyl alcohol with cyclohexane as entrainer. Two optimal separation systems are generated, including one with a single-dividing wall column and one with a double-dividing wall column. In comparison with an energy-efficient azeotropic distillation sequence containing two stripping columns by Chang et al. (2012) [1], simulation results show that the former two systems can cut steam usage further by 6.0%. The two systems save about 5.4–6.1% in terms of TAC. DWCs prove to be superior to the convention distillation systems with respect to both cost and energy efficiency.     

乙醇脱水塔内两相和三相共沸精馏

研究了乙醇脱水塔内的两相共沸精馏和汽液液三相共沸精馏过程。利用Aspen plus模拟软件对乙醇脱水塔内4种工况的精馏曲线、共沸剂浓度分布、回流量和再沸器能耗进行了分析比较。结果表明,苯做共沸剂时,脱水塔内两相共沸精馏和汽液液三相共沸精馏的精馏曲线、共沸剂浓度分布、回流量和再沸器能耗相近,脱水塔精馏曲线都跨越了精馏边界,并且共沸剂在塔内大多数板上都有较高浓度分布。而环己烷做共沸剂时,两相共沸精馏工况和汽液液三相共沸精馏工况条件下的脱水塔内精馏曲线、共沸剂浓度分布、回流量和再沸器能耗有较大差别。汽液液三相共沸精馏工况条件下,环己烷在塔内大多数板上有较高浓度分布,起到较好的脱水作用,而两相共沸精馏工况条件下脱水塔内共沸剂仅分布在塔顶几块塔板上,塔内多数板上没有起到共沸剂作用。     

Batch‐Rektifikation azeotroper Gemische in Verstärkungs‐ und Abtriebskolonnen

Batch distillation is an efficient unit operation which allows the separation of a multicomponent mixture into its pure constituents in a single column. However, the separation of azeotropic mixtures by distillation is quite difficult because at the azeotrope the liquid and the gas have the same composition and, in turn, the driving force for distillation disappears. A systematic presentation of batch distillation processes for the separation of binary azeotropic mixtures using an entrainer is given.     

萃取、共沸精馏技术联用回收废液中的醋酸

针对化工生产过程中产生的稀醋酸溶液难以回收高纯度醋酸的问题,首先采用乙酸乙酯和苯的混合溶剂萃取浓缩稀醋酸溶液;再通过精馏蒸出溶液中的萃取剂和部分水;最后采用乙酸丁酯作为挟带剂,用共沸精馏法分离得到醋酸。得到的醋酸质量分数达96.84%,回收率达84.97%。对工业化回收稀醋酸溶液中的醋酸有一定的实用价值。     

A semicontinuous approach for heterogeneous azeotropic distillation processes

The separation of azeotropes has substantial energy and investment costs, and the available methods require high capital costs for reconstruction of process plants. As an alternative, a semicontinuous configuration that utilizes an existing plant with minor modifications has been explored. In this paper, a semicontinuous, heterogeneous azeotropic distillation process is proposed and acetic acid dehydration process is used as a case study. To carry out the simulation work, Aspen HYSYS^® simulation software is used along with MATLAB^® and an interface program to handle the mode-transition of the semicontinuous process. Sensitivity analyses on operating parameters are performed to identify the process limits. Comparisons are made to conventional heterogeneous azeotropic distillation, and dividing-wall distillation column on the annual cost. The results proved that the semicontinuous system is the best setup in terms of total annual costs and energy requirements.     

Feasible separations and entrainer selection rules for heteroazeotropic batch distillation

A feasibility analysis is presented for the separation of close-boiling and azeotropic (minimum- and maximum-boiling) binary mixtures into pure components by the addition of an entrainer introducing a heterogeneous azeotrope. The analysis is done for both the conventional batch rectifier and the multivessel batch column. The analysis is theoretical and based on the assumptions of total reflux/reboil ratios and infinite number of stages. Two feasibility conditions are formulated that make it possible to investigate feasibility based on information coming solely from the distillation line map along with the binodal curve of the ternary mixture. Serafimov's classification is used for classifying the azeotropic phase diagrams. The feasibility analysis provides the necessary background and information for formulating rules for entrainer selection for the process. Two simple rules are then proposed, which make it possible to “screen” entrainers for heteroazeotropic batch distillation with minimum efforts.     

Operation and control of batch extractive distillation for the separation of mixtures with minimum-boiling azeotrope

Batch distillation is commonly used in the fine chemicals, specialty polymer, biochemical, pharmaceutical, and food industries. For separating mixtures with minimum-boiling azeotrope, a heavy entrainer is frequently added to the top section of the batch column to aid in the separation. This process is called batch extractive distillation. Most of the papers in open literature have only studied the first operating step of the batch extractive distillation which is the recovery of the light component without mentioning the later steps for the recovery of the other component and entrainer. In this paper, two real chemical systems, one separating acetone and methanol using water as entrainer and the other separating isopropyl alcohol (IPA) and water using dimethyl sulfoxide (DMSO) as entrainer, are studied for the feasible operation of the complete batch distillation sequence. The operating variables, including the pre-load amount with the mixture, continuous feed rate of the entrainer, and reflux ratio at each operating step are determined in the operating sequence. The constant reflux ratio and constant entrainer feed rate operating policy and another policy to allow these two operating variables to be varied will be compared in order to further improve the batch operation. All dynamic simulations that are performed directly mimic industrial situations from an empty column using a rigorous dynamic simulator, Aspen Dynamics™.     

Separation of tert‐Butyl Alcohol‐Water Mixtures by a Heterogeneous Azeotropic Batch Distillation Process

Tert‐butyl alcohol and water form an azeotrope at normal pressure. Simple distillation cannot be used to separate these two components. In this article, a systematic study of the separation of tert‐butyl alcohol–water mixtures with an entrainer by heterogeneous azeotropic batch distillation was performed. Based upon the thermodynamic behavior of the ternary mixtures, cyclohexane was chosen as the entrainer. It formed ternary and binary heterogeneous azeotropes with the original components. The process feasibility analysis was validated by using rigorous simulation with chemical process simulation software – HYSYS Plant 2.2 and DISTIL 4.1. Simulation results were then corroborated in a batch experimental column for the selected entrainer.