共查询到20条相似文献,搜索用时 78 毫秒
1.
根据液晶的减摩作用,研究了液晶作为润滑添加剂在改善机床爬行状况,即降低其爬行临界速度方面的实际应用。选择了3种液晶,每种都按6种不同的浓度加入到N32(旧标准HJ20)机械油中,在M7130型平面磨床上进行了试验。试验结果表明,液晶作为润滑添加剂确实具有良好的防爬作用,且防爬效果与液晶种类及其添加浓度有关。 相似文献
2.
液晶添加剂的润滑性能研究 总被引:1,自引:0,他引:1
本文对一种新型润滑添加剂-液晶添加剂的减摩抗磨性能进行了初步的研究,试验结果表明:添加剂的有效性与液晶类型及其浓度有关,如添加剂HOB在(0.1~1)%的浓度范围内,随着添加剂浓度的增加,摩擦系数下降。对于面接触摩擦副,在比压为15MPa,速度为0.504m/s时,加有1%HOB液晶添加剂的润滑油与未加添加剂时相比较,其摩擦系数从0.108下降到0.013,而且磨损率也大为降低。这说明了液晶作为一种有效的减摩抗磨添加剂在工业应用中有着良好的发展前景。 相似文献
3.
4.
液晶润滑添加剂的抗磨损性能研究 总被引:2,自引:1,他引:1
本文研究液晶润滑添加剂的抗磨性能,将1%正辛基苯甲酸液晶材料加入至HU-20汽轮机油中,在Falex试验机上试验结果表明具有降低磨损量和缩短磨合时间的作用,与不加添加剂时相比较,线磨损量降低44%,摩擦系数降低31-47%,磨合时间短一倍。在四球试验机上试验,最大无卡咬负荷PB值增加21%。液晶添加剂对改善润滑油的抗磨性能作用明显。 相似文献
5.
6.
7.
机床爬行是由摩擦力特性所引起的一种自激振动,会严重影响被加工零件的加工精度、表面粗糙度以及机床的定位精度,甚至使机床不能进行正常工作。因此,设计精密机床时必须重视和加以解决。
试验表明,两个相对运动部件之间的摩擦系数是随着速度的变化而变化的。一般,静摩擦系数总是大于动摩擦系数。摩擦力特性表现为机床运动部件启动时,由导轨间静摩擦系数下降为动摩擦系数,并且动摩擦系数随速度增加而下降。 相似文献
8.
数控机床爬行故障通常发生在机械部分和进给伺服系统部分,因为数控机床进给系统低速时的爬行现象往往取决于机械传动部分的特性。而爬行一般是由于机床传动刚度不够,摩擦副的静动摩擦系数之差大和摩擦副的振荡阻尼太小所引起的。本文建立了系统的物理模型和数学模型,通过理论分析和仿真分析得出机床运动部件产生爬行的主要原因,并提出防止运动部件产生爬行的主要措施。 相似文献
9.
10.
11.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
12.
13.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
一种涡旋压缩机径向随变机构的设计 总被引:1,自引:0,他引:1
详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。 相似文献
17.
V. P. Dragunov E. G. Kostsov 《Optoelectronics, Instrumentation and Data Processing》2009,45(3):234-242
Specific features of operation of one- and two-capacitor microelectromechanical converters (MEMC) of energy of mechanical microscopic vibrations into electric energy with a modulated electrode-gap magnitude and with allowance for the mutual influence of electrical and elastic forces are analyzed, and the characteristics of these two devices are compared. The main factors restricting the increase in MEMC power are demonstrated to be the effects of “collapsing” and the condition of conservation of positive rigidity of the system. Expressions for estimating the limiting MEMC parameters are derived. The possibility of electrical energy generation in the presence of “real“ sources of wide-spectrum microscopic vibrations is considered. 相似文献
18.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献
19.
20.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献