Phase Transitional Behavior and Piezoelectric Properties of Lead-Free (Na0.5K0.5)NbO3–(Bi0.5K0.5)TiO3 Ceramics

(1− x )(Na_0.5K_0.5)NbO₃–(Bi_0.5K_0.5)TiO₃ solid solution ceramics were successfully fabricated, exhibiting a continuous phase transition with changing x at room temperature from orthorhombic, to tetragonal, to cubic, and finally to tetragonal symmetries. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal ferroelectric phases was found at 2–3 mol% (Bi_0.5K_0.5)TiO₃ (BKT), which brings about enhanced piezoelectric and electromechanical properties of piezoelectric constant d ₃₃=192 pC/N and planar electromechanical coupling coefficient k _p=45%. The MPB composition has a Curie temperature of 370°–380°C, comparable with that of the widely used PZT materials. These results demonstrate that this system is a promising lead-free piezoelectric candidate material.     

Variability of the Sr/Ti Ratio in SrTiO3

TiO₂ is observed as a second phase in SrTiO₃ having Sr/Ti ≤ 0.995 (≥0.5 mol% excess TiO₂). The effect of excess TiO₂ on the equilibrium electrical conductivity at 1000°C is consistent with a solubility of <0.1 mol% TiO₂ with the formation of unassociated oxygen vacancies. More Ti0₂ is retained in solid solution when samples are quenched from the sintering temperature rather than furnace-cooled. The effect of excess SrO on the equilibrium electrical conductivity also indicates some solid solubility.     

The System HfO2-TiO2

The system HfO₂-TiO₂ was studied in the 0 to 50 mol% TiO₂ region using X-ray diffraction and thermal analysis. The monoclinic ( M ) ⇌ tetragonal ( T ) phase transition of HfO₂ was found at 1750°± 20°C. The definite compound HfTiO₄ melts incongruently at 1980°± 10°C, 53 mol% TiO₂. A metatectic at 2300°± 20°C, 35 mol% TiO₂ was observed. The eutectoid decomposition of HfO_2,ss) ( T ) → HfO_2,ss ( M ) + HfTiO_34,ssss occurred at 1570°± 20°C and 22.5 mol% TiO₂. The maximum solubility of TiO₂ in HfO_2,ss,( M ) is 10 mol% at 1570°± 20°C and in HfO_2,ss ( T ) is 30 mol% at 1980°± 10°C. On the HfO₂-rich side and in the 10 to 30 mol% TiO₂ range a second monoclinic phase M of HfO₂( M ) type was observed for samples cooled after a melting or an annealing above 1600°C. The phase relations of the complete phase diagram are given, using the data of Schevchenko et al. for the 50% to 100% TiO₂ region, which are based on thermal analysis techniques.     

Formation and Transformation of TiO2 (Anatase) Solid Solution in the System TiO2—Al2O3

In the system TiO₂—Al₂O₃, TiO₂ (anatase, tetragonal) solid solutions crystallize at low temperatures (with up to ∼ 22 mol% Al₂O₃) from amorphous materials prepared by the simultaneous hydrolysis of titanium and aluminum alkoxides. The lattice parameter a is relatively constant regardless of composition, whereas parameter c decreases linearly with increasing Al₂O₃. At higher temperatures, anatase solid solutions transform into TiO₂ (rutile) with the formation of α-Al₂O₃. Powder characterization is studied. Pure anatase crystallizes at 220° to 360°C, and the anatase-to-rutile phase transformation occurs at 770° to 850°C.     

Solubility of TiO2 in ZrO2

The solubility of TiO₂ in tetragonal ZrO₂ is 13.8±0.3 mol% ui 1300°C, 14.9±0.2 mol% at 1400°C, and 16.1±0.2 mol% at 1500°C. These solid solutions transform to metastable monoclinic solid solutions without compositional change on cooling to room temperature.     

Ta2O5/Nb2O5 and Y2O3 Co-doped Zirconias for Thermal Barrier Coatings

Zirconia doped with 3.2–4.2 mol% (6–8 wt%) yttria (3–4YSZ) is currently the material of choice for thermal barrier coating topcoats. The present study examines the ZrO₂-Y₂O₃-Ta₂O₅/Nb₂O₅ systems for potential alternative chemistries that would overcome the limitations of the 3–4YSZ. A rationale for choosing specific compositions based on the effect of defect chemistry on the thermal conductivity and phase stability in zirconia-based systems is presented. The results show that it is possible to produce stable (for up to 200 h at 1000°–1500°C), single (tetragonal) or dual (tetragonal + cubic) phase chemistries that have thermal conductivity that is as low (1.8–2.8W/m K) as the 3–4YSZ, a wide range of elastic moduli (150–232 GPa), and a similar mean coefficient of thermal expansion at 1000°C. The chemistries can be plasma sprayed without change in composition or deleterious effects to phase stability. Preliminary burner rig testing results on one of the compositions are also presented.     

Pseudobinary Phase Relations of Li2Ti3O7

The Li₂O-TiO₂ pseudobinary phase diagram was determined from 50 to 100 mol% TiO₂ by DTA, microscopy, and X-ray analysis; Li₂Ti₃O₇ effectively melts congruently at 1300° and decomposes eutectoidally at 940°C. A solid solution based on Li₂TlO₃ from 50 to ∼65 mol% TiO₃ was observed to exist at >930°C. A new metastable phase was discovered with a composition of ∼75 mol% TiO₂ and with a hexagonal unit cell (8.78 by 69.86 × 10⁻¹nm). Discrepancies in the literature regarding some of these phase equilibria are reconciled.     

Effects of Ba6Ti17O40 on the Dielectric Properties of Nb-Doped BaTiO3 Ceramics

The dielectric properties, including the DC breakdown strength, of 1 mol% Nb⁵⁺-doped BaTiO₃ ceramics with different quantities of excess TiO₂ have been investigated. The breakdown strength was found to decrease with increasing TiO₂ content, but could not be readily explained by relative density and grain size effects. The decrease in the breakdown strength from a stoichiometric BaTiO₃ composition to samples with excess TiO₂ is believed to be due to the field enhancement effect (up to a factor of 1.40) at the BaTiO₃ matrix because of the presence of a Ba₆Ti₁₇O₄₀ second phase. The thermal expansion coefficient mismatch between the BaTiO₃ matrix phase and the Ba₆Ti₁₇O₄₀ phase may also result in a low breakdown strength. The dielectric properties of the pure Ba₆Ti₁₇O₄₀ phase were also investigated and are reported herein.     

Humidity-Sensitive Electrical Conduction of MgCr2O4-TiO2 Porous Ceramics

The crystalline phase, microstructure, semiconduction, and humidity-sensitive electrical conduction of MgCr₂O₄-TiO₂ ceramics were studied. A solid solution with TiO₂ up to 30 mol% occurs as a single phase with a pure MgCr₂O₄-type spinel structure. The humidity-sensitive electrical conduction of the MgCr₂O₄-TiO₂ porous ceramics is the most promising for humidity-sensing devices.     

Synchrotron Radiation Ti-k XANES Study of TiO2─Y2O3-Stabilized Tetragonal Zirconia Polycrystals

Valence state and site symmetry of Ti ions in TiO₂–Y₂O₃–ZrO₂ powders with 2 mol% Y₂O₃ and 5, 10, 15, and 20 mol% TiO₂, respectively, are studied by X-ray absorption near-edge spectroscopy (XANES). Tetravalent Zr⁴⁺ ions are replaced predominantly by Ti⁴⁺ ions. Within the solubility region of Ti ions, a subsequent displacement of Ti ions from the center of symmetry is observed with increasing TiO₂ content in TiO₂–Y₂O₃-stabilized tetragonal ZrO₂ polycrystals (Ti-Y-TZP) under investigation. This behavior cannot be interpreted with a random substitution of Ti⁴⁺ ions on Zr⁴⁺ lattice sites. On the contrary, this correlation between the TiO₂ content in Ti-Y-TZP and the shift of Ti ions indicates an increasing interaction between the Ti ions with growing TiO₂ content, caused by a subsequent clustering of Ti ions.     

Dielectric Properties of the Fluorite-like Bi2O3–Nb2O5 Solid Solution and the Tetragonal Bi3NbO7

Our analysis of the microwave dielectric properties of the δ-Bi₂O₃–Nb₂O₅ solid solution (δ-BN_ss) showed a continuous increase in permittivity and dielectric losses with an increasing concentration of Nb₂O₅. The only discontinuity was found for the temperature coefficient of resonant frequency, which is negative throughout the entire homogeneity range but reaches a minimum value for the sample with 20 mol% Nb₂O₅. At the same composition there is a discontinuity in the grain size of the δ-BN_ss ceramics. For the sample containing 25 mol% Nb₂O₅ two structural modifications were observed. A single-phase tetragonal Bi₃NbO₇, in the literature referred to as a Type-III phase, is formed in a very narrow temperature range from 850° to 880°C. A synthesis performed below or above this temperature range resulted in the formation of the end member of the δ-BN_ss homogeneity range. Compared with the δ-BN_ss the Bi₃NbO₇ ceramics exhibit lower microwave dielectric losses, an increased conductivity, and a positive temperature coefficient of resonant frequency.     

Electrical Conductivity Measurements to Detect Suspected Liquid Phase in the Al2O3-I mol% TiO2-0.5 mol% NaO1/2 and Other Systems

A liquid phase in the Al₂O₃-1 mol% TiO₂-0.5 mol% NaO_1/2 composition is confirmed at ±1300°C by an electrical conductivity measurement. The ease of the method led to a study of the Al₂O₃-2 mol% CuO-2 mol% TiO₂ system and to the geologically important detection of eutectics (peritectics) in rock materials.     

Effect of BiScO3 and LiNbO3 on the Piezoelectric Properties of (Na0.5K0.5)NbO3 Ceramics

Lead-free potassium sodium niobate-based piezoelectric ceramics (1− y )(Na_{0.5−0.5 x} K_{0.5−0.5 x} Li _x )NbO₃− y BiScO₃ (  y =0.01, x= 0–0.06) have been prepared by an ordinary sintering process. The XRD analysis showed that the structure changes from orthorhombic to tetragonal with the increase of x (at y =0.01, abbreviated as KNNBSL100 x ). At room temperature, the polymorphic phase transition from the orthorhombic to the tetragonal phase was identified at approximately 0.02≤ x ≤0.04. The piezoelectric and ferroelectric properties were significantly enhanced. The temperature dependences of the relative permittivity revealed that the Curie temperature was increased with the addition of LiNbO₃. These solid solution ceramics are promising as potential lead-free candidate materials.     

Revised Phase Diagram of the System ZrO2-CeO2 Below 1400°C

The phase diagram of the system ZrO₂-CeO₂ was rein-vestigated using hydrothermal techniques. Cubic, tetragonal, and monoclinic solid solutions are present in this system. The tetragonal solid solution decomposes to monoclinic and cubic solid solutions by a eutectoid reaction at 1050°50°C. The solubility limits of the tetragonal and cubic solid solutions are about 18 and 70 mol% CeO₂, respectively, at 1400°C, and about 16 and 80 mol% CeO₂, respectively, at 1200°C. Solubility limits of the monoclinic and cubic solid solutions are about 1.5 and 88 mol% CeO₂ at 1000°C, and 1.5 and 98 mol% CeO₂ at 800°C, respectively. The compound Ce₂Zr₃O₁₀ is not found in this system.     

Cubic-to-Tetragonal Displacive Transformation in Gd2O3–Bi2O3 Ceramics

Gd₂O₃-doped Bi₂O₃ polycrystalline ceramics containing between 2 and 7 mol% Gd₂O₃ were fabricated by pressureless sintering powder compacts. The as-sintered samples were tetragonal at room temperature. Hightemperature X-ray diffraction (XRD) traces showed that the samples were cubic at elevated temperatures and transformed into the tetragonal polymorph during cooling. On the basis of conductivity measurements as a function of temperature and differential scanning calorimetry (DSC), the cubic → tetragonal as well as tetragonal → cubic → teansition temperatures were determined as a function of Gd₂O₃ concentration. The cubic → tetragonal transformation appears to be a displacive transformation. It was observed that additions of ZrO₂ as a dopant, which is known to suppress cation interdiffusion in rare-earth oxide–Bi₂O₃ systems, did not suppress the transition, consistent with it being a displacive transition. Annealing of samples at temperatures 660°C for several hundred hours led to decomposition into a mixture of monoclinic and rhombohedral phases. This shows that the tetragonal polymorph is a metastable phase.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Anatase-Type TiO2 and ZrO2-Doped TiO2 Directly Formed from Titanium(III) Sulfate Solution by Thermal Hydrolysis: Effect of the Presence of Ammonium Peroxodisulfate on their Formation and Properties

Anatase-type TiO₂ powder containing sulfur with absorption in the visible region was directly formed as particles with crystallite in the range 15–88 nm by thermal hydrolysis of titanium(III) sulfate (Ti₂(SO₄)₃) solution at 100°–240°C. Because of the presence of ammonium peroxodisulfate ((NH₄)₂S₂O₈), the yield of anatase-type TiO₂ from Ti₂(SO₄)₃ solution was accelerated, and anatase with fine crystallite was formed. Anatase-type TiO₂ doped with ZrO₂ up to 9.8 mol% was directly precipitated as nanometer-sized particles from the acidic precursor solutions of Ti₂(SO₄)₃ and zirconium sulfate in the presence and the absence of (NH₄)₂S₂O₈ by simultaneous hydrolysis under hydrothermal conditions at 200°C. By doping ZrO₂ into TiO₂ and with increasing ZrO₂ content, the crystallite size of anatase was decreased, and the anatase-to-rutile phase transformation was retarded as much as 200°C. The anatase-type structure of ZrO₂-doped TiO₂ was maintained after heating at 1000°C for 1 h. The favorable effect of doping ZrO₂ to anatase-type TiO₂ on the photocatalytic activity was observed.     

Direct Formation of Iron(III)-Doped Titanium Oxide (Anatase) by Thermal Hydrolysis and Its Structural Property

Anatase-type TiO₂ (titania) doped with iron up to 19.8 mol% was directly formed as nanometer-sized particles from acidic precursor solutions of TiOSO₄ and Fe(NO₃)₃ by simultaneous hydrolysis, under mild hydrothermal conditions at 180°3C. Iron content in the anatase-type TiO₂ was much less than that of the starting composition of the precursor solutions because of slower hydrolysis rate of Fe(NO₃)₃ than that of TiOSO₄ at 180°3C. The XRD data, TEM selected-area diffraction patterns, and Mössbauer effect measurement showed that iron(III) formed a solid solution in the anatase-type TiO₂ precipitates and that there was no iron oxide precipitated as secondary phase without making a solid solution with TiO₂ present in the precipitates. Doping of Fe₂O₃ into TiO₂ shifted the phase transformation from anatase-type to rutile-type structure to a low temperature. On the phase transformation from anatase to rutile, iron oxide was precipitated as Fe₂TiO₅ (pseudobrookite) phase. When the iron content was increased in the anatase phase, onset of optical absorption shifted to longer wavelengths, and absorption in the UV-light region and in the visible-light region over 400–600 nm clearly appeared in the diffuse reflectance spectra of the as-prepared Fe(III)-doped TiO₂.     

Subsolidus Phase Equilibria and Ordering in the System ZrO2-Y2O3

The subsolidus phase relations in the entire system ZrO₂-Y₂O₃ were established using DTA, expansion measurements, and room- and high-temperature X-ray diffraction. Three eutectoid reactions were found in the system: ( a ) tetragonal zirconia solid solution→monoclinic zirconia solid solution+cubic zirconia solid solution at 4.5 mol% Y₂O₃ and ∼490°C, ( b ) cubic zirconia solid solutiow→δ-phase Y₄Zr₃O₁₂+hexagonalphase Y₆ZrO₁₁ at 45 mol% Y₂O₃ and ∼1325°±25°C, and ( c ) yttria C -type solid solution→wcubic zirconia solid solution+ hexagonal phase Y₆ZrO₁₁ at ∼72 mol% Y₂O₃ and 1650°±50°C. Two ordered phases were also found in the system, one at 40 mol% Y₂O₃ with ideal formula Y₄Zr₃O₁₂, and another, a new hexagonal phase, at 75 mol% Y₂O₃ with formula Y₆ZrO₁₁. They decompose at 1375° and >1750°C into cubic zirconia solid solution and yttria C -type solid solution, respectively. The extent of the cubic zirconia and yttria C -type solid solution fields was also redetermined. By incorporating the known tetragonal-cubic zirconia transition temperature and the liquidus temperatures in the system, a new tentative phase diagram is given for the system ZrO₂-Y₂O₃.     

The Ba(Ti,Zr)O3–(Zr,Ti)O2 Field in the Phase System BaO–TiO2–ZrO2

The two-phase field involves a ZrO₂-TiO₂ solid solution containing no more than 4 mol% TiO₂, and a BaTiO₃-BaZrO₃ solid solution containing a maximum of 75 mol% BaTiO₃. The field narrows above 1300°C, probably because of the intrusion of a liquid-phase field into the ternary, beginning near the BaO-TiO₂ edge.