共查询到20条相似文献,搜索用时 281 毫秒
1.
在2.0 A/dm2、24°C和空气搅拌条件下,采用由60 g/L Cu SO4·5H2O、200 g/L H2SO4、60 mg/L Cl-和4种添加剂组成的酸性镀铜液对印制线路板通孔进行电镀铜。以PCB通孔孔口、孔中心铜层厚度和镀液的深镀能力为指标,通过正交试验对添加剂聚二硫二丙烷磺酸钠(SPS)、聚乙二醇(PEG-10000)、季铵盐类化合物(MX-86)和嵌段聚醚类化合物(SQ-5)的用量进行优化,得到添加剂的最优组合为:SPS 20 mg/L,SQ-5 0.5 g/L,PEG-10000 0.2 g/L,MX-86 20 mg/L。采用该配方对深径比为8∶1的通孔电镀时,深镀能力在90%以上,铜层的延展性和可靠性均能满足印制线路板的工业应用要求。 相似文献
2.
以75 g/L CuSO4·5H2O、230 g/L硫酸和0.1 g/L十二烷基苯磺酸钠(SDBS)组成的溶液作为基础镀液,并以Cl-、聚乙二醇(PEG-10000)、聚二硫二丙烷磺酸钠(SPS)及2,2′-二硫代二吡啶(2-PDS)作为添加剂,在温度(23±2)℃、电流密度1.8 A/dm2和空气搅拌的条件下对印制电路板(PCB)上深径比为10∶1的通孔电镀铜。以深镀能力作为评价指标,通过正交试验对添加剂用量进行优化,得到较优的组合为:SPS 5 mg/L,PEG 250 mg/L,Cl- 60 mg/L,2-PDS 2 mg/L。采用该组合添加剂电镀通孔时,深镀能力高达112.9%,镀层均匀、细致、平整,抗热冲击性能良好,符合PCB生产对可靠性的要求。 相似文献
3.
羟基烷基磺酸镀液电镀Sn—Pb合金的研究 总被引:2,自引:0,他引:2
我国自行研制生产的羟基烷基磺酸电镀Sn-Pb合金镀液已经在部分厂家投产使用.生产实践证明,该镀液能获得不同铅含量的、可焊性优良且镀层结晶细致而光亮的Sn-Pb合金镀层.本研究重点测定了该镀液的电化学性能,如阴极电流效率、分散能力及深镀能力.并对添加剂的作用进行了研究探讨. 相似文献
4.
经过赫尔槽试验对添加剂各组份的筛选,酮作主光亮剂、含氮有机酸R作辅助光亮剂,添加剂的镀液的部份电化学性能和整平能力、了测试,并与商品添加剂进行比较.选择OP-20作载体光亮剂、苄叉丙配制了DH-I添加剂.对加入DH_1分散能力和深镀能力等电镀性能进行 相似文献
5.
为解决使用传统电镀液配方进行挠性板通孔电镀时出现的均镀能力(TP)差等问题,本文基于加速剂聚二硫二丙烷磺酸钠(SPS)、N,N-二甲基二硫代甲酰胺丙烷磺酸钠(DPS)的电化学性能测试,研究了整平剂对挠性板通孔电镀效果的影响,并对无整平剂的镀液体系中挠性板通孔电镀的影响因素进行了分析讨论。结果表明,SPS具有持续性的加速作用,是典型的加速剂,而DPS在高浓度条件下呈现出抑制效果,具有加速-整平双重特性;无整平剂体系下挠性板通孔的电镀效果(TP≥200%)明显要比有整平剂体系下的电镀效果(TP≈100%)要好,但是无整平剂条件下所得的铜镀层质量差;通过在无整平剂体系中加入DPS,利用DPS的微整平性能能够有效改善镀层质量。提高镀液中的铜离子浓度,降低酸的浓度、采用小电流密度、短时间电镀以及低气流量有利于提高通孔电镀的均镀能力。 相似文献
6.
本文对含有JD-1型添加剂的黑铬电镀溶液的分散能力、深镀能力、阴极极化曲线、镀层的硬度、耐磨性、耐蚀性、光学性能、镀层应力及其与基体材料的结合力作了测定,还研究了镀层的表面形貌。阐明了该添加剂的含量与镀液性能和镀层性能的关系,展示了JD型黑铬电镀工艺在生产上获得应用的原因及广泛的应用前景。 相似文献
7.
8.
9.
10.
以电镀理论为依据,采用化学和电化学方法设计开发了JZN_11高性能环保碱性镀锌添加剂工艺。该工艺的主要创新和研究成果体现在赫尔槽试验0.1 A电流时哈氏片全光亮,6 A电流时仅有0.5 cm左右的烧焦,电流密度相差20倍时厚度比小于1.6,操作温度可达52℃,镀层镜面光亮细致,结合力好,分散能力高于82%,深镀能力好,阴极电流效率在65%~90%,单剂添加,操作简单,性价比高,符合了电镀清洁生产要求,可在生产中应用。另外,通过电镀试验比较了该工艺与传统DPE型及美国某进口品牌组合添加剂的电镀效果。 相似文献
11.
12.
13.
Dinesh Singh J. K. Gehlawat Musti S. Rao 《Journal of chemical technology and biotechnology (Oxford, Oxfordshire : 1986)》1990,47(2):127-136
Oslefins and diolefins are important intermediates in the petrochemical industry and the future promises a further substantial increase in demand. While several catalysts have been formulated in the past for the abstraction of hydrogen from butenes and propylene, these catalysts are inefficient in the abstraction of first hydrogen from butane. Bismuth molybdates (β and γ-phases) containing iron oxide and supported on alumina are used as catalysts in the present investigation on the oxidative dehydrogenation of n-butane. Effects of catalyst content, temperature and oxygen: n-butane ratio on conversion and selectivity to butadiene and (C4H8 + C4H6) are studied in the following ranges of experimental conditions: β-bismuth molybdate/100 mol support I(K), 3–9; γ-bismuth molybdate/100 mol support I(K), 5-20; temperature, 400–500°C; O2: butane ratio, 0.6:1.7. 相似文献
14.
考登钢作为一种高耐候结构钢,广泛应用于各个领域。在火力发电方面,考登钢主要应用在工作环境比较恶劣的烟气加热器和空气预热器中。考登钢表面涂搪的目的就是进一步提高其耐腐蚀性能,延长使用寿命。为了提高考登钢元件的使用寿命,对考登钢表面涂搪瓷的可行性、密着性能、瓷釉、工艺控制、质量保证等方面进行了研究。 相似文献
15.
A viscometer used to measure the viscosity of 10 μl of a liquid, must be miniaturized down, and the liquid velocity gradient in the channel used to determine the viscosity coefficient. Two major factors that affect the liquid velocity are the mechanical forces exerted by the mechanical motors and electromagnetic forces. In this study, electrowetting on dielectric (EWOD) is adopted to drive liquids. Variously sized electrodes on a chip, and two shapes of channel are employed to measure the velocity gradient to determine the viscosity coefficient. The device is fabricated by microelectromechanical system (MEMS) technology. The dielectric layer used in EWOD has a high dielectric constant, BST (Ba0.7Sr0.3TiO3), to reduce the required applied voltage; its surface is coated with hydrophobic polymer, polytetrafluoro-ethylene (PTFE, Teflon® AF DuPont). Experimental results demonstrate that liquids can be pulled at 660 μm/s in linear channels by applying a voltage of 15 V. 相似文献
16.
17.
18.
研究了温度和pH值对漆酶酶活以及漆酶处理纤维压制纤维板性能的影响。结果表明,pH较低、温度较高时漆酶酶活较高,压制的纤维板强度性能较好。但温度太高(60~80℃),延长加热时间,漆酶稳定性变差,酶活明显降低,压制纤维板的强度下降。 相似文献
19.
In reexamining medium effects on photochemical reactions, we have emphasized those on unequilibrated excited species such as the Franck-Condon species. Despite recent advances in femtochemistry, such a discussion in molecular photochemistry is uncommon, and the problem remains challenging on account of the extremely short-lived excited species. However, in such cases, a small perturbation resulting from, for example, weak guest-host interactions could turn into a determining factor in dictating the course of a photochemical channel of deactivation. Examples of medium-directed diabatic processes have been examined with this idea in mind. A modified view on rhodopsin photoisomerization is presented along with the consideration that confinement does not necessarily lead to inhibition of reactions of the trapped substrate. 相似文献
20.
采用实验方法考察工艺参数对沉降斑的影响。基于一个带凸台的平板模具,采用L27(313)正交矩阵进行实验,研究了几何尺寸、熔体温度、注射时间、保压压力及保压时间对厚度突变处沉降斑形成的影响,同时还考虑了熔体温度和注射时间以及保压压力和注射时间之间的交互作用影响;通过性噪比分析和F检验优化成型工艺条件并对工艺参数的影响进行显著性分析。结果表明,对于厚度突变的平板制品,厚度突变的程度对其沉降斑形成的影响最大,其次为熔体温度,保压压力,保压时间等;采取减小厚度变化,降低熔体温度或增加保压压力和保压时间等措施,可以减小厚度突变处沉降斑,从而减少其对外观质量的影响;因素之间的交互作用对制品沉降斑的形成有一定的影响,熔体温度B和注射时间C之间的交互作用影响较为明显,而保压压力D和注射时间C之间的交互作用对该质量指标的影响最小,可以并入误差。 相似文献