Experimental investigation of convective heat transfer coefficient during downward laminar flow condensation of R134a in a vertical smooth tube

This paper presents an experimental investigation of laminar film condensation of R134a in a vertical smooth tube having an inner diameter of 7–8.1 mm and a length of 500 mm. Condensation experiments were performed at mass fluxes of 29 and 263 kg m^?2 s^?1. The pressures were between 0.77 and 0.1 MPa. The heat transfer coefficient, film thickness and condensation rate during downward condensing film were determined. The results show that an interfacial shear effect is significant for the laminar condensation heat transfer of R134a under the given conditions. A new correlation for the condensation heat transfer coefficient is proposed for practical applications.     

Effects of heat flux,vapour quality,channel hydraulic diameter on flow boiling heat transfer in variable aspect ratio micro-channels using transparent heating

Experiments on flow boiling heat transfer in high aspect ratio micro-channels with FC-72 were carried out. Three channels with different hydraulic diameters (571, 762 and 1454 μm) and aspect ratios (20, 20 and 10) were selected. The tested mass fluxes were 11.2, 22.4 and 44.8 kg m^?2 s^?1 and heat fluxes ranging from 0–18.6 kW m^?2. In the present study, boiling curves with obvious temperature overshoots are presented. Average heat transfer coefficient and local heat transfer coefficient along stream-wise direction are measured as a function of heat flux and vapour quality respectively. Slug-annular flow and annular flow are the main flow regimes. Convective boiling is found to be the dominant heat transfer mechanism. Local heat transfer coefficient increases with decreasing hydraulic diameter. Moreover, the effect of hydraulic diameter is more significant when mass flux is higher. The unique channel geometry is considered as the decisive reason of the flow regimes as well as heat transfer mechanisms.     

Effect of cross sectional shape during condensation in a single square minichannel

The objective of this work is to present new condensation heat transfer coefficients measured inside a single square cross section minichannel, having a 1.18 mm side length, and compare them to the ones previously measured in a circular minichannel. Tests have been performed with R134a at 40 °C saturation temperature, at mass velocity ranging between 200 and 800 kg m^?2 s^?1. As compared to the heat transfer coefficients measured in the circular cross section channel, for the same hydraulic diameter, in the square minichannel the authors find a heat transfer enhancement at the lowest value of mass velocity, which must be due to the effect of surface tension. No heat transfer coefficient increase has been found at the highest values of the mass velocity where condensation is shear stress dominated.     

Comparison of numerical and experimental performance criteria of an ammonia–water bubble absorber using plate heat exchangers

A mathematical model for ammonia–water bubble absorbers was developed and compared with experimental data using a plate heat exchanger. The analysis was performed carrying out a sensitive study of selected operation parameters on the absorber thermal load and mass absorption flux. Regarding the experimental data, the values obtained for the solution heat transfer were in the range 0.51–1.21 kW m^?2 K^?1 and those of the mass absorption flux in the range 2.5–5.0 × 10^?3 kg m^?2 s^?1. The comparison between experimental and simulation results was acceptable being the maximum difference of 11.1% and 28.4% for the absorber thermal load and the mass absorption flux, respectively.     

A new critical heat flux correlation for vertical water flow through multiple thin rectangular channels

A critical heat flux (CHF) study of the vertical up-flow of water through multiple thin rectangular channels was conducted. Pressures varied from 89.8 to 115 kPa, inlet temperatures from 291 to 306 K, and mass fluxes from 9.5 to 39 kg m^?2 s^?1. Electrical resistance heaters embedded in aluminum provided a uniform heat flux. A more universal and robust CHF correlation based on the geometry of the Advanced Test Reactor at Idaho National Laboratory was developed. This new CHF correlation predicts 126 data points from this and three previous studies within an error of ±8.5% with a 95% confidence.     

Comparison of frictional pressure drop models during annular flow condensation of R600a in a horizontal tube at low mass flux and of R134a in a vertical tube at high mass flux

This study compares well-known two-phase pressure drop models with the experimental results of a condensation pressure drop of (i) R600a in a 1 m long horizontal smooth copper tube with an inner diameter of 4 mm, outer diameter of 6 mm and (ii) R134a in a 0.5 m vertical smooth copper tube with an inner diameter of 8.1 mm and outer diameter of 9.52 mm. Different vapour qualities (0.45–0.9 for R600a and 0.7–0.95 for R134a), various mass fluxes (75–115 kg m^?2 s^?1 for R600a and 300–400 for R134a kg m^?2 s^?1) and different condensing temperatures (30–43 °C for R600a and 40–50 °C for R134a) were tested under annular flow conditions. The quality of the refrigerant in the test section was calculated considering the temperature and pressure obtained from the experiment. The pressure drop across the test section was directly measured with a differential pressure transducer. The most agreeable correlations of various available options were then identified according to the results of analysis during annular flow regime.     

Comparison of the CHF data for water and refrigerant HFC-134a by using the fluid-to-fluid modeling methods

CHF experiments in tubes and annulus cooled with HFC-134a have been performed. The HFC-134a and water CHF data have been compared by applying the Ahmad and the Katto modeling parameters. For the mass fluxes from 710 to 3500 kg m⁻² s⁻¹ in the tubes, the HFC-134a and water CHF data fall close to the same curve on the plane of the dimensionless CHF vs. the Ahmad and the Katto modeling parameters. For the mass fluxes below 600 kg m⁻² s⁻¹ in an annulus, the dimensionless CHFs as a function of the Ahmad and the Katto modeling parameters show a large difference between the HFC-134a and the water. The Katto and the Ahmad modeling parameters cannot be correlated with the dimensionless CHF data for HFC-134a and water on the same curve in the low mass flux and high quality conditions.     

Influence of the flashing phenomenon on the boiling curve of refrigerant R134a in minichannels

The results of experimental investigations of heat transfer during the flow of R134a in a minichannel are presented here. The experimental investigations were conducted using a minichannel with a total length of 500 mm and 1.68 mm internal diameter. The heated length of the minichannel was 200 mm, the total mass flow rate of the refrigerant (wρ) = 200–450 kg/m² s, the inlet subcooling ΔT_s = 5–15 K, and the heat flux density q = 1.7–60.3 kW/m². The results of experimental investigations are presented as a boiling curve. The phenomenon known as the zero boiling crisis and the influence of the flashing phenomenon on the boiling curve show the importance of these elements on heat transfer in single- and two-phase systems.     

Dry-out CHF correlation for R134a flow boiling in a horizontal helically-coiled tube

An experimental study was carried out to investigate the R134a dry-out critical heat flux (CHF) characteristics in a horizontal helically-coiled tube. The test section was heated uniformly by DC high-power source, and its geometrical parameters are the outer diameter of 10 mm, inner diameter of 8.4 mm, coil diameter of 300 mm, helical pitch of 75 mm and valid heated length of 1.89 m. The experimental parameters are the outlet pressures of 0.30–0.95 MPa, mass fluxes of 60–500 kg m^?2 s^?1, inlet qualities of ?0.36–0.35 and heat fluxes of 7.0 × 10³–5.0 × 10⁴ W m^?2. A method based on Agilent BenchLink Data Logger Pro was developed to determine the occurrence of CHF with a total of 68 T-type thermocouples (0.2 mm) set along the tube for accurate temperature measurement. The characteristics of wall temperatures and the parametric effect on dry-out CHF showed that temperature would jump abruptly at the point of CHF, which usually started to form at the front and offside (270° and 90°) of the outlet cross-section. The CHF values decrease nearly linearly with increasing inlet qualities, while they decrease more acutely with increasing critical qualities, especially under larger mass flux conditions. The mass flux has a positive effect on CHF enhancement, but the pressure has negative one. A new dimensionless correlation was developed to estimate dry-out CHF of R134a flow boiling in horizontal helically-coiled tubes under current experimental conditions and compared to calculated results from Bowring and Shah correlations.     

A complex but accurate correlation for predicting critical heat flux in a round tube for low and medium pressures under circumferentially non-uniform heating conditions

This paper presents an empirical correlation for predicting the critical heat flux (CHF) of vertical, upward, steam–water flows in round tubes for low and medium pressures under circumferentially non-uniform heating conditions. This correlation is based on experiments carried out with test sections having an inner diameter of 22 mm and heated lengths ranging from 1.8 to 3.5 m. The ratios between the maximum and the minimum heat fluxes were 1.0, 4.7 and 8.3. The experiments were carried out for outlet pressures and mass fluxes ranging from 10 to 40 bar and 300 to 1600 kg m^?2 s^?1, respectively. The root mean square error of predicted CHF values by using the proposed correlation and applying the heat balance method is 3.7%.     

Experimental investigation on two-phase flow boiling heat transfer of five refrigerants in horizontal small tubes of 0.5, 1.5 and 3.0 mm inner diameters

An experimental investigation on two-phase flow boiling heat transfer with refrigerants of R-22, R-134a, R-410A, C₃H₈ and CO₂ in horizontal circular small tubes is presented. The experimental data were obtained over a heat flux range of 5–40 kW m^?2, mass flux range of 50–600 kg m^?2 s^?1, saturation temperature range of 0–15 °C, and quality up to 1.0. The test section was made of stainless steel tubes with inner diameters of 0.5, 1.5 and 3.0 mm, and lengths of 330, 1000, 1500, 2000 and 3000 mm. The experimental data were mapped on Wang et al. (1997) [5] and Wojtan et al. (2005) [6] flow pattern maps. The effects of mass flux, heat flux, saturation temperature and inner tube diameter on the heat transfer coefficient are reported. The experimental heat transfer coefficients were compared with some existing correlations. A new boiling heat transfer coefficient correlation that is based on a superposition model for refrigerants in small tubes is presented with 15.28% mean deviation and ?0.48% average deviation.     

Refrigerant flow boiling heat transfer in parallel microchannels as a function of local vapor quality

Flow boiling of refrigerant HFC-134a in a multi-microchannel copper cold plate evaporator is investigated. The heat transfer coefficient is measured locally for the entire range of vapor qualities starting from subcooled liquid to superheated vapor. The test piece contains 17 parallel, rectangular microchannels (0.762 mm wide) of hydraulic diameter 1.09 mm and aspect ratio 2.5. The design of the test facility is validated by a robust energy balance as well as a comparison of single-phase heat transfer coefficients with results from the literature. Results are presented for four different mass fluxes of 20.3, 40.5, 60.8, and 81.0 kg m^?2 s^?1, which correspond to refrigerant mass flow rates of 0.5–2.0 g s^?1, and at three different pressures 400, 550 and 750 kPa corresponding to saturation temperatures of 8.9, 18.7, and 29 °C. The wall heat flux varies from 0 to 20 W/cm² in the experiments. The heat transfer coefficient is found to vary significantly with refrigerant inlet quality and mass flow rate, but only slightly with saturation pressure for the range of values investigated. The peak heat transfer coefficient is observed for a vapor quality of approximately 20%.     

Experimental investigation and modelling of heat transfer during convective boiling in a minichannel

Flow boiling heat transfer characteristics of water are experimentally studied in a circular minichannel with an inner diameter of 1500 μm. The fluid flows upwards and the test section, made of the nickel alloy Inconel 600, is directly electrically heated. Thus, the evaporation takes place under the defined boundary condition of constant heat flux. Mass fluxes between 50 and 100 kg/(m² s) and heat fluxes from 10 to 115 kW/m² at an inlet pressure of 3 bar are examined.Infrared thermography is applied to measure the outer wall temperatures of the minichannel. This experimental method permits the identification of different boiling regions, boiling mechanisms and the determination of local heat transfer coefficients. Measurements are carried out in single-phase flow, subcooled and saturated boiling regions. The experimental heat transfer coefficients in the region of saturated boiling are compared with correlations available in literature and with a physically founded model developed for convective boiling.     

Experimental investigation of single-phase turbulent flow of R-134a in a multiport microchannel heat sink

This experimental study aims to investigate the heat transfer characteristics of single-phase turbulent flow of R-134a refrigerant in a rectangular multi-micro channel heat sink having 27 channels where each channel has a hydraulic diameter of 421 μm. Experimental results were obtained for inlet temperatures ranging from 24 to 33 °C, mass fluxes from 1485 to 2784 kg m^− 2 s^− 1 and wall heat fluxes from 3 to 24 kW m^− 2. The results indicate that the heat transfer coefficients are found to be higher at lower inlet temperatures than those at higher ones. In addition, when equal amount of heat supplied to the heat sink, the heat transfer coefficients increase with increasing the mass flux of refrigerant. They were also compared with 12 well-known correlations and it was seen that 4 of 12 were in good agreement with each other with the average deviation < 10%. The findings demonstrate that well-known correlations in fundamental sources can be used to predict the heat transfer coefficient of R-134a during its single phase flow in a multiport microchannel heat sink under turbulent regime.     

Convective boiling of pure and mixed refrigerants: An experimental study of the major parameters affecting heat transfer

An experimental study is carried out to investigate the characteristics of the evaporation heat transfer for different fluids. Namely, pure refrigerants fluids (R22 and R134a), azeotropic and quasi-azeotropic mixtures (R404A, R410A, R507) and zeotropic mixtures (R407C and R417A).The test section is a smooth, horizontal, stainless steel tube (6 mm ID, 6 m length) uniformly heated by the Joule effect. The flow boiling characteristics of the refrigerant fluids are evaluated in 250 different operating conditions. Thus, a data-base of more than 2000 data points is produced.The experimental tests are carried out varying: (i) the refrigerant mass fluxes within the range 200–1100 kg/m² s; (ii) the heat fluxes within the range 3.50–47.0 kW/m²; (iii) the evaporating pressures within the range 3.00–12.0 bar.In this study, the effect on measured heat transfer coefficient of vapour quality, mass flux, saturation temperature, imposed heat flux, thermo-physical properties are examined in detail.     

High heat flux flow boiling in silicon multi-microchannels – Part III: Saturated critical heat flux of R236fa and two-phase pressure drops

New experimental critical heat flux results for saturated boiling conditions have been obtained for R236fa flowing in a silicon multi-microchannel heat sink composed of 67 parallel channels, 223 μm wide, 680 μm high and with 80 μm thick fins separating the channels. The microchannel length was 20 mm. The footprint critical heat fluxes measured varied from 112 to 250 W/cm² and the wall critical heat fluxes from 21.9 to 52.2 W/cm² for mass velocities from 276 to 992 kg/m²s. When increasing the mass velocity, the wall critical heat flux was observed to increase. The inlet saturation temperatures (20.31 ? T_sat,in ? 34.27 °C) and the inlet subcoolings (0.4 ? Δ T_sub ? 15.3 K) were found to have a negligible influence on the saturated CHF. The best methods for predicting the data were those of Wojtan et al. [L. Wojtan, R. Revellin, J. R. Thome, Investigation of critical heat flux in single, uniformly heated microchannels, Exp. Therm. Fluid Sci. 30 (2006) 765–774] and Revellin and Thome [R. Revellin, J. R. Thome, A theoretical model for the prediction of the critical heat flux in heated microchannels, Int. J. Heat Mass Transfer 50 (in press)]. They both predict the experimental CHF results with a mean absolute error of around 9%. Using the critical vapour quality, an annular-to-dryout transition is also proposed as a limit in a diabatic microscale flow pattern map. Pressure drop measurements were measured and analysed, showing that the homogeneous model could correctly predict the observed trends.     

A composite heat transfer correlation for saturated flow boiling in small channels

Recent reviews of flow boiling heat transfer in small tubes and channels have highlighted the need for predictive correlations that are applicable over a wide range of parameters and across different studies. A composite correlation is developed in the present work which includes nucleate boiling and convective heat transfer terms while accounting for the effect of bubble confinement in small channels. The correlation is developed from a database of 3899 data points from 14 studies in the literature covering 12 different wetting and non-wetting fluids, hydraulic diameters ranging from 0.16 to 2.92 mm, and confinement numbers from 0.3 to 4.0. The mass fluxes included in the database range from 20 to 3000 kg m^?2 s^?1, the heat fluxes from 0.4 to 115 W cm^?2, the vapor qualities from 0 to 1, and the saturation temperatures from ?194 to 97 °C. While some of the data sets show opposing trends with respect to some parameters, a mean absolute error of less than 30% is achieved with the proposed correlation.     

A novel time strip flow visualisation technique for investigation of intermittent dewetting and dryout in elongated bubble flow in a microchannel evaporator

A flow visualisation study of flow boiling of R245fa in silicon multi-microchannels at low mass flux and moderate heat flux has been carried out with a high speed digital camera. The micro-evaporator had 67 channels of length 20 mm, width 223 μm, and height 680 μm while the fin width between adjacent channels was 80 μm. The base heat flux ranged from 2 to 26 W cm^?2 for a mass velocity of 100 kg s^?1 m^?2, resulting in exit vapour qualities ranging from 10% to 70%. In particular, a novel time strip technique was developed to analyse the recorded image sequences and significantly highlight the various phenomena occurring along given channels. Notably, this technique was able to reveal profound details regarding the intermittent dryout mechanism of liquid films trapped between the elongated bubbles and the heated channel walls. The results show that the intermittent dryout of the evaporating liquid film is comprised of four stages with distinct time scales and dynamics: (i) the growth of liquid film thinning perturbations to a critical amplitude causing the rupture of the metastable liquid film, (ii) a dewetting stage involving expanding dry spots leading to a rivulet flow regime, (iii) evaporation of the rivulets leading to full dryout, and (iv) a rewetting stage. This intermittent dryout mechanism appears to explain the many seemingly contradictory heat transfer coefficient trends observed with changes in vapour quality in microchannels, thus resolving an important heat transfer dilemma. Furthermore, since dryout is an undesirable event during the practical application of a microchannel evaporator, it is important to delay or even suppress the initial rupture of the liquid film that leads to dryout. This can be achieved by manufacturing or treating the channel surfaces to be highly wettable with the chosen refrigerant.     

Evaporation heat transfer and pressure drop of HFC-134a in a helically coiled concentric tube-in-tube heat exchanger

The two-phase heat transfer coefficient and pressure drop of HFC-134a during evaporation inside a smooth helically coiled concentric tube-in-tube heat exchanger are experimentally investigated. The test section is a 5.786-m long helically coiled tube with refrigerant flowing in the inner tube and heating water flowing in the annulus. The inner tube is made from copper tubing of 9.52 mm outer diameter and 7.2 mm inner diameter. The heat exchanger is fabricated by bending a straight copper tube into a spiral coil. The diameter of coil is 305 mm. The test run are done at average saturated evaporating temperatures ranging between 10 and 20 °C. The mass fluxes are between 400 and 800 kg m⁻² s⁻¹ and the heat fluxes are between 5 and 10 kW m⁻². The inlet quality of the refrigerant in the test section is calculated using the temperature and pressure obtained from the experiment. The pressure drop across the test section is directly measured by a differential pressure transducer. The effects of heat flux, mass flux and, evaporation temperature on the heat transfer coefficients and pressure drop are also discussed. The results from the present experiment are compared with those obtained from the straight tube reported in the literature. New correlations for the convection heat transfer coefficient and pressure drop are proposed for practical applications.     

High heat flux flow boiling in silicon multi-microchannels – Part I: Heat transfer characteristics of refrigerant R236fa

This article is the first in a three part study on flow boiling of refrigerants R236fa and R245fa in a silicon multi-microchannel heat sink. The heat sink was composed of 67 parallel channels, which are 223 μm wide, 680 μm high and 20 mm long with 80 μm thick fins separating the channels. The base heat flux was varied from 3.6 to 221 W/cm², the mass velocity from 281 to 1501 kg/m² s and the exit vapour quality from 2% to 75%. The working pressure and saturation temperature were set nominally at 273 kPa and 25 °C, respectively. The present database includes 1217 local heat transfer coefficient measurements, for which three different heat transfer trends were identified, but in most cases the heat transfer coefficient increased with heat flux and was almost independent of vapour quality and mass velocity. Importantly, it was found for apparently the first time that the heat transfer coefficient as a function of vapour quality reaches a maximum at very high heat fluxes and then decreases with further increase of heat flux.