原位热压TiC/Ti/Al合成Ti2AlC的研究

以TiC/Ti/Al为原料,采用热压工艺在1400℃原位合成和烧结了含少量第二相Ti3AlC2的Ti2AlC材料.通过不同温度和不同热压时间下合成试样的XRD分析探讨了Ti2AlC的合成过程.结果表明,高温下Ti与Al反应生成中间相TiAl金属间化合物,然后TiC与TiAl金属间化合物反应生成Ti2AlC.初期反应非常迅速,大部分Ti2AlC在此阶段生成.反应后期反应物减少,速度变慢,同时生成少量第二相Ti3AlC2.不同温度下合成的Ti2AlC颗粒具有不同的形貌特征.     

放电等离子合成Ti3AlC2-TiB2复合材料的相形成研究

采用放电等离子烧结工艺,以Ti,Al,B4C,Tic为原料制备Ti3AlC2/TiB2复合材料.通过X射线衍射分析了从600℃到1 300℃Ti3AlC2/TiB2系统反应过程的相形成规律.用扫描电镜观察了不同温度下试样的显微组织演变.结果表明,在900℃之前,主要的反应是Ti和AJ反应生成Ti-A1金属问化合物,900℃之后,Ti-Al金属问化合物与TiC逐渐生成Ti3AlC2和TiB2相,形成致密Ti3AlC2/TiB2复合材料.     

Ti_2AlC/Al_2O_3复合材料的原位合成及其力学性能

以Ti、TiC、Al和TiO2为原料,通过原位热压反应烧结法在1 350℃合成Ti2AlC/Al2O3复合材料。利用XRD详细研究了其反应过程,并分析了Al2O3对材料微观结构和性能的影响。结果表明,该体系在热压过程中的反应分多步进行,主要包括Ti粉与Al粉反应生成Ti-Al金属间化合物,TiO2与Al反应生成Al2O3以及Ti-Al金属间化合物与TiC反应生成Ti2AlC材料。原位反应生成的Al2O3均匀分布在Ti2AlC晶界上,抑制了Ti2A1C晶体的异常生长,从而使基体相Ti2AlC晶粒细小、均匀。力学性能测试表明Ti2AlC/12%(质量分数)Al2O3复合材料的硬度、抗压强度、抗弯强度和断裂韧性较Ti2AlC单相材料分别提高了66%,126%,130%和19.3%,并分析了其改性机理。     

新型Ti_3AlC_2-Al_2O_3/TiAl_3复合材料的组织结构与性能

利用Al-TiO2-TiC体系,通过机械球磨和反应热压制备出Ti3AlC2与Al2O3两相原位内生成增强TiAl3金属基复合材料。借助DSC、XRD、SEM和TEM研究了复合材料的反应机制、显微组织、力学性能及抗氧化性能。结果表明,球磨50h后的复合粉末经1 250℃/50 MPa保温10min烧结后可得到组织均匀细小且致密的Ti3AlC2-Al2O3/TiAl3复合材料,其密度、维氏硬度、室温三点弯曲强度、断裂韧性及压缩强度分别为3.8g/cm3、8.4GPa、658.9 MPa、7.9 MPa·m1/2和1 742.0 MPa,1 000℃的高温压缩强度为604.1 MPa。Ti3AlC2-Al2O3/TiAl3复合材料的增韧机制主要包括Ti3AlC2和Al2O3颗粒的剥离、Ti3AlC2相导致的裂纹偏转和桥接以及Ti3AlC2颗粒的变形及层裂。Ti3AlC2-Al2O3/TiAl3复合材料在700~1 000℃温度区间内生成的氧化层虽不致密,但仍表现出优异的抗高温循环氧化性能。     

放电等离子烧结制备致密TiAl/Ti2AlC复合材料

本研究以Ti／Al/TiC为原料，采用放电等离子烧结工艺制备致密TiAl/Ti2AlC复合材料。制备材料主要由TiA1和Ti2AlC两相组成。当原料中掺人体积分数为7％的TiC时，Ti-A1基体由γ相和层状相所构成，而Ti2AlC颗粒则均匀分布在基体中。经热处理后，则转变为Ti2AlC颗粒均匀分布在由γ相构成的基体中的结构。研究中还测定了所得复合材料的断裂韧性和弯曲强度。     

Ti_2AlC-TiB_2对TiAl基复合材料组织及力学性能的影响

以Ti、Al和B4C为原料,采用真空电弧熔炼的方法制备了含Ti_2AlC-TiB_2增强相的TiAl基复合材料;分析了添加不同含量的Ti_2AlC-TiB_2对复合材料的物相组成、组织结构及力学性能的影响,并探讨了微观组织结构的形成机制。结果表明:Ti_2AlC-TiB_2/TiAl复合材料主要由TiAl、Ti3Al、TiB_2和Ti_2AlC等物相组成,TiB_2和Ti_2AlC分布在层片状的TiAl+Ti3Al基体中;随着原料中B4C含量的增多,复合材料组织中Ti_2AlC-TiB_2含量增多,且TiAl基体的晶粒被明显细化,TiB_2和Ti_2AlC分布于基体晶界或晶内。Ti_2AlC主要为层片状和板条状,尺寸5~15μm,而TiB_2颗粒形态与其含量有关,当Ti_2AlC-TiB_2含量小于20wt%时,TiB_2颗粒呈针棒状,尺寸为0.5~5μm,当Ti_2AlC-TiB_2含量增加到30wt%时,TiB_2颗粒主要呈块状,尺寸为5~20μm。Ti_2AlC由TiC与Ti-Al熔体发生包晶反应生成,Ti_2AlC和TiB_2的形成提高了Ti_2AlC-TiB_2/TiAl复合材料的硬度、塑性和抗压强度。当4Ti+Al+B4C的加入量为10wt%时,复合材料的变形量比纯TiAl提高14%,而抗压强度达到最高值1 591 MPa。Ti_2AlC和TiB_2通过裂纹偏转、颗粒钉扎、拔出等机制对Ti_2AlC-TiB_2/TiAl复合材料起到增强增塑的作用。     

添加TiC和Ti3AlC2对燃烧合成Ti3AlC2粉体的影响

Ti、Al、C和TiC组成的Ti:Al:C=3:1.1:1.8(摩尔比)体系的燃烧合成实验结果表明,当在体系中未加入TiC时,得到的主要是TiC,但加入TiC后燃烧合成产物主要是Ti3AlC2,且Ti3AlC2量随TiC加入量的增加而增加,随燃烧反应体系温度的降低而增加;加入晶种Ti3AlC2有利于合成Ti3AlC2相物质.     

热压反应烧结法制备Al_2O_3/Ti_2AlC复合材料及其微观结构和性能

以Ti、Al和活性炭粉为原料,通过高能球磨及热压反应烧结法在1200℃合成Al2O3/Ti2AlC复合材料,即是在Ti2AlC层状材料的制备过程中同时被合成。研究了烧结温度对反应产物的影响,并重点分析了材料微观结构和性能的关系。结果表明:高能球磨使Ti2AlC的烧结温度降低,热压烧结在1200℃时得到了物相比较均匀、致密的Al2O3/Ti2AlC复合材料;同时分析材料微观结构,少量Al2O3的引入抑制了Ti2A1C晶体的异常长大,使得晶粒细小且均匀。力学性能测试表明,该材料室温抗弯强度可达275.4MPa,断裂韧度可达10.5MPa.m1/2,密度为4.2g/cm3。     

Ti-34Al基复合材料颗粒相组成及分布

采用XD法制备Ti-34Al基复合材料，XRD、OM和EPM的分析结果表明：复合材料的基体由Ti3Al和TiAl双相组成，增哟相由单相TiC和具有Ti3AlC包覆层的TiC两种结构的颗粒组成，单相TiC来自于凝固过程中的共晶反应，而具有Ti3AlC包覆层的TiC则是由于不完成包晶反应的结晶，单相TiC颗料沿晶界均匀分布的特征表明在较快的凝固条件下，初生相β-Ti以树枝晶方式生长，树枝晶凝固过程中颗粒枝晶凝固界面排斥在枝晶间。固液界面结构，冷却速度和颗粒大小影响颗粒与固液界面的相互作用。     

热压复合制备Ti-Al3Ti层状复合材料组织结构研究

采用热压复合工艺在不同工艺参数下制备了Ti-Al3Ti层状复合材料,利用SEM和EDS对材料的组织结构进行了观察,研究了热压复合工艺参数对Ti/Al扩散反应及反应层微观组织结构的影响规律.结果表明,在不同工艺参数下,Ti/Al叠层热压复合反应的初生相均为Al3Ti.600℃时Ti/Al叠层只发生少许反应,在界面处生成一薄层Al3Ti,650和700℃时,Al层完全反应,各层界面处结合状态良好,层间结合紧密.650℃时Al3Ti为唯一生成相,但700℃时,由于反应动力学的影响Al3Ti/Ti层之间有TiAl层生成,Ti-Al系金属间化合物的生成顺序为Al3Ti→TiAl.反应过程中液相的存在能够使Ti、Al持续紧密接触,加快反应速度,促进反应顺利进行.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from