共查询到15条相似文献,搜索用时 140 毫秒
1.
2.
3.
4.
阐述了钼粉粒度和松装密度对拉丝用钼条质量的影响 ,提出了钼粉松装密度的控制应和粒度控制并重的观点 相似文献
5.
6.
7.
8.
9.
10.
11.
Gas-sprayed R6M5F3 high-speed steel powder has been examined for the effects of grain size and shape for the initial powder
and for the powder deformed by rolling, as regards the poured density and strength of compacts. The particle size and shape
have been determined with a specialized SIAMS analysis suite. The changes in the particle shape factors for the rolled powder
reduce the poured density and increase the strength of compacts.
__________
Translated from Poroshkovaya Metallurgiya, Nos. 1–2(447), pp. 12–18, January–February, 2006. 相似文献
12.
X射线管转轴的高性能钼棒制备是钼材加工中的一个难点,研究选用适宜的钼粉,制定合理烧结工艺,采用特殊的锻造工艺,生产出性能指标达到美国ASTM387-90标准的钼棒。结果表明:采用平均粒度2.2μm,松装密度1.14 g/cm3的钼粉压制后在氢气感应炉中1 920℃烧结3 h后,再采用加热1 2001 400℃,道次加工率24%1 400℃,道次加工率24%2%,总加工率74%,5次模锻的锻造工艺能获得密度为10.2 g/cm3的钼棒,再经900℃保温半小时的消应力退火,可以得到抗拉强度大于620 MPa,延伸率大于30%,组织结构均匀的高性能钼棒。 相似文献
13.
研究热导管铜粉的松装密度、粉末粒度、粉末粒径分布对铜粉烧结的毛细结构体断裂强度、孔隙率、毛细力吸水通量的影响。结果表明:在烧结温度为980℃,烧结时间60 min的条件下松装烧结所得铜热导管毛细结构体综合性能良好,当铜粉松装密度2.1 g/cm~3,粒径范围100~250μm,其中粒径150~250μm的质量分数为40%~70%时,铜粉烧结毛细结构体的断裂强度为9.11~9.67 MPa,孔隙率52.6%~53.8%,毛细力吸水通量1.30×10~(-3)~1.42×10~(-3) g/(s·mm~2)。 相似文献
14.
15.
研究了利用纯钼骨架熔渗法制备Mo70Cu30、Mo60Cu40(质量分数)合金的相关工艺。结果表明:试验原料可选取经高温预处理及筛分后费氏粒度为5.2μm,粒度分布范围较窄及C、O含量低的纯钼粉,不添加诱导Cu粉。利用限位法压制成型的钼素坯经H2气氛在1200~1300℃预烧结出孔隙率ε(%)为33.5%、45.2%的纯钼骨架,在H2气氛熔融态Cu中经1 200~1 350℃熔渗60~120 min可制得Cu含量为31.3%、40.7%的Mo70Cu30、Mo60Cu40合金。利用纯钼骨架熔渗法制备的Mo-Cu合金相对密度可达到98%以上,微观形貌可见Mo、Cu两相均匀分布。 相似文献