Ferroelectric and Structural Properties of the Pb(Sc1/2Nb1/2)1-x,Tix,O3 System

Extensive solid solution was observed in the system Pb(Sc_1/2/,Nb_1/2,)_1-x,Ti_x,O₃. In the range 0 ≤ x ≤ 0.425 a rhombohedral ferroelectric phase was stable at 25° C. In the range 0.45 ≤ x ≤ 1.00 a tetragonal ferroelectric phase was stable at this temperature. The phase diagram of the system below 500° C strongly resembles that of PbZrO₃−PbTiO₃. The compound Pb(Sc_1/2Nb_1/2)O₃ exhibited rhombohedral perovskite cell symmetry below the ferroelectric ↔ paraelectric transition temperature, and the angle a was acute. The radial coupling coefficient was 0.46 for the composition Sc_1/2Nb_1/2)_0.575Ti_0.4250O₃. At 25°C this composition consisted primarily of the rhombohedral phase with a small amount of the tetragonal phase present. The ferroelectric ↔ paraelectric transition occurred over a temperature range in the rhombohedral phase field. The spontaneous polarization was finite at temperatures considerably above the temperature of the permittivity maximum for a given rhombohedral solid solution.     

Phase Transitional Behavior and Piezoelectric Properties of Lead-Free (Na0.5K0.5)NbO3–(Bi0.5K0.5)TiO3 Ceramics

(1− x )(Na_0.5K_0.5)NbO₃–(Bi_0.5K_0.5)TiO₃ solid solution ceramics were successfully fabricated, exhibiting a continuous phase transition with changing x at room temperature from orthorhombic, to tetragonal, to cubic, and finally to tetragonal symmetries. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal ferroelectric phases was found at 2–3 mol% (Bi_0.5K_0.5)TiO₃ (BKT), which brings about enhanced piezoelectric and electromechanical properties of piezoelectric constant d ₃₃=192 pC/N and planar electromechanical coupling coefficient k _p=45%. The MPB composition has a Curie temperature of 370°–380°C, comparable with that of the widely used PZT materials. These results demonstrate that this system is a promising lead-free piezoelectric candidate material.     

Growth of Pb((Zn1/3Nb2/3)0.91Ti0.09)O3 Single Crystals Using an Allomeric Seed Crystal and Their Electrical Properties

Single crystals of Pb((Zn_1/3Nb_2/3)_0.91Ti_0.09)O₃ (PZNT 91/9), 28 mm in diameter and 30 mm in length, have been successfully grown using a modified Bridgman technique with an allomeric seed crystal. X-ray fluorescence analysis (XRFA) measurement confirms that the effect of segregation is not serious. The segregation coefficient k for PbTiO₃ content during crystal growth is 0.99, which causes some fluctuation in the composition along the growth direction. The fluctuation of composition and the complicated domain structure cause a variation of electric properties. Dielectric measurement indicates that PZNT 91/9 crystals exhibit an almost normal ferroelectric phase transition at ∼183°C from the tetragonal phase to the cubic phase. In addition, a weak frequency-dependent ferroelectric-ferroelectric phase transition is observed at ∼85°C, which is attributed to partial conversion of the rhombohedral phase to a tetragonal phase. The dielectric thermal hysteresis behavior and the existence of polarization above the Curie temperature verify that the phase transitions at ∼85° and 183°C are first order with a slight diffuse character and first order, respectively. It is demonstrated that the effects of segregation can be decreased and the homogeneity of the obtained PZNT 91/9 single crystals can be improved by optimizing growth parameters.     

Effect of BiScO3 and LiNbO3 on the Piezoelectric Properties of (Na0.5K0.5)NbO3 Ceramics

Lead-free potassium sodium niobate-based piezoelectric ceramics (1− y )(Na_{0.5−0.5 x} K_{0.5−0.5 x} Li _x )NbO₃− y BiScO₃ (  y =0.01, x= 0–0.06) have been prepared by an ordinary sintering process. The XRD analysis showed that the structure changes from orthorhombic to tetragonal with the increase of x (at y =0.01, abbreviated as KNNBSL100 x ). At room temperature, the polymorphic phase transition from the orthorhombic to the tetragonal phase was identified at approximately 0.02≤ x ≤0.04. The piezoelectric and ferroelectric properties were significantly enhanced. The temperature dependences of the relative permittivity revealed that the Curie temperature was increased with the addition of LiNbO₃. These solid solution ceramics are promising as potential lead-free candidate materials.     

Microstructure and Dielectric Characteristics of (PbxBa0.5−xSr0.5)TiO3 Ceramics

Microstructural and dielectric properties of the Pb _x Ba _0.5__x —Sr_0.5TiO₃ system have been studied. It is found that this system forms a solid solution in the entire composition range (0.0≤ x ≤0.5) and is cubic for the x = 0, 0.1, and 0.2 compositions and tetragonal for other compositions. Measurements of the dielectric constant as a function of temperature reveal that this material is ferroelectric at room temperature for the x > 0.2 compositions and has a broad paraelectric-ferroelectric transition region. No shift in the dielectric maxima was noted; however, there is a slight spread in the dielectric constant with frequency for the x = 0.4 composition. A quantitative model to mathematically analyze the effect of composition fluctuations on the dielectric broadening for a ternary system is presented. Transmission electron microscopic studies reveal the presence of 90° ferroelectric domains oriented along the {01     } planes for the x = 0.3 and 0.4 compositions.     

Morphotropic Phase Boundary in the Pb(Zn1/3Nb2/3O3)-BaTiO3-PbTiO3 System

The morphotropic phase boundary (MPB) in the relaxor ferroelectric system Pb(Zn_1/3Nb_2/3O₃)-BaTiO₃-PbTiO₃ (PZN-BT-PT) with 15 mol% BT was investigated through dielectric permittivity and high-temperature X-ray diffraction measurements. It was revealed that MPB is a broad composition region extending from 12 to 18 mol% PT, within which the temperatures of the permittivity maximum are close to the ending temperatures for the phase transformation from coexisting rhombohedral and tetragonal phases to cubic phase on heating. When the specimen is cooled, the starting temperatures for the rhombohedral-to-tetragonal phase transition increase with increasing PT content. The large thermal hysteresis observed by X-ray diffraction is caused by the phase transformation between rhombohedral and tetragonal phases. On cooling, the MPB curves toward the PT-rich side, so that ceramics within this composition range undergoe successive phase transitions from cubic to rhombohedral and from rhombohedral to tetragonal phase. The diffuseness of the paraelectric-to-ferroelectric phase transition is remarkably decreased by the addition of PT. The enhanced dielectric permittivity peak values for the MPB compositions are correlated with the reduced lattice distortion and phase coexistence.     

Crystal Structure and Ferroelectric Properties of (Bi0.5Na0.5)TiO3–Ba(Zr0.05Ti0.95)O3 Piezoelectric Ceramics

The crystal structure and ferroelectric properties of (1− x )(Bi_0.5Na_0.5)TiO₃– x Ba(Zr_0.05Ti_0.95)O₃ (BNBZT x, x ≤12%) lead-free piezoelectric ceramics were studied. The distance between the centers of cations and anions ( d _c–a) as well as the lattice parameters was carefully investigated by Rietveld refinement on X-ray diffraction patterns. It was found that the crystal phase was determined by the amount of Ba(Zr_0.05Ti_0.95)O₃ added, whereas the pure rhombohedral and tetragonal phases are observed in compositions containing x ≤4 and x ≥8%, respectively. A rhombohedral–tetragonal morphotropic phase boundary (MPB) was found at around BNBZT6, which showed a maximum and minimum d _c–a at its rhombohedral and tetragonal phases, respectively. According to the present study, the ferroelectric properties show a strong dependence on their crystal phases. For the single-phase compositions, the remanent polarization ( P _r) generally increased with the value of d _c–a while their coercive fields ( E _c) were determined by their lattice parameters. Nevertheless, the behavior in P _r and E _c for MPB compositions is related to not only the lattice parameter but also the composed phases.     

Cubic-to-Tetragonal Displacive Transformation in Gd2O3–Bi2O3 Ceramics

Gd₂O₃-doped Bi₂O₃ polycrystalline ceramics containing between 2 and 7 mol% Gd₂O₃ were fabricated by pressureless sintering powder compacts. The as-sintered samples were tetragonal at room temperature. Hightemperature X-ray diffraction (XRD) traces showed that the samples were cubic at elevated temperatures and transformed into the tetragonal polymorph during cooling. On the basis of conductivity measurements as a function of temperature and differential scanning calorimetry (DSC), the cubic → tetragonal as well as tetragonal → cubic → teansition temperatures were determined as a function of Gd₂O₃ concentration. The cubic → tetragonal transformation appears to be a displacive transformation. It was observed that additions of ZrO₂ as a dopant, which is known to suppress cation interdiffusion in rare-earth oxide–Bi₂O₃ systems, did not suppress the transition, consistent with it being a displacive transition. Annealing of samples at temperatures 660°C for several hundred hours led to decomposition into a mixture of monoclinic and rhombohedral phases. This shows that the tetragonal polymorph is a metastable phase.     

Structural and Dielectric Investigation of the PbTiO3-BaZrO3 System

Thermal expansion measurements, dielectric measurements, and X-ray diffraction studies were made of the PbTiO₃-BaZrO₃ system. A dielectric constant maximum of 11,300 was found at the Curie temperature for the Pb_0.80-Ba_0.20Ti_0.80Zr_0.20O₃ composition. The transition from a ferroelectric tetragonal phase to a para-electric cubic phase for the 10, 20, and 30 mole % BaZrO₃ in PbTiO₃ compositions was of first order. X-ray diffraction determination of the lattice parameters (25°C) showed that this tetragonal-to-cubic phase transition occurred at a composition of 44 mole % BaZrO₃.     

Dielectric and Piezoelectric Properties of Pb(Co1/3Nb2/3)O3-PbTiO3-PbZrO3 Solid Solution Ceramics

Ceramic and piezoelectric properties of the Pb(Co_1/3Nb_2/3)O₃-PbTiO₃-PbZrO₃ system were investigated. The system contains rhombohedral, tetragonal, and pseudocubic phases at room temperature. The triple point is at 0.07Pb(Co_1/3Nb_2/3)O₃-0.43PbTiO₃-0.50PbZrO₃. High dielectric constants (750 to 1500) and radial coupling coefficients (40 to 45%) and low average temperature coefficients of resonant frequency (of the order of 10^-6°C) were obtained for compositions near the morphotropic phase boundary.     

Dielectric Behavior in the Systems PbHfO3—BaHfO3 and PbHfO3—SrHfO3

An intermediate antiferroelectric phase was observed in both the systems (Pb,Ba)HfO₃ and (Pb,Sr)HfO₃ whereas the intermediate antiferroelectric phase has been reported to be observed only in the system (Pb,Sr)ZrO₃ of the analogous zirconate systems. A ferroelectric phase was observed in the system (Pb,Ba)HfO₃. This ferroelectric phase was determined to be rhombohedral with the angle between the rhombohedral axes slightly less than 90°. The differences which were observed between the hafnate systems investigated and the analogous zirconate systems are attributed to the lower electronic polarizability of the hafnium ion.     

Ferroic Phase Transitions in (Na1/2Bi1/2)TiO3 Crystals

The ferroic phase-transition behavior of two (Na_1/2Bi_1/2)TiO₃(NBT) crystals grown by flux and by the Czochralski method has been investigated in the present study. Although both the tetragonal and the rhombohedral phases of NBT are expected to be ferroelastic, these crystals exhibit different ferroelastic behavior. The two NBT crystals also show differences in the amount of temperature hysteresis and the thermal expansion coefficients. These differences can be attributed to nonstoichiometry and structural variations dependent on the growing method. The present investigation has revealed a second maximum at −450°C in dielectric constant (( T )) curves, which could indicate that the intermediate tetragonal phase is either polar or antipolar. This maximum, however, originates from space-charge polarization and interaction between the charge carrier and the electrode, such that the tetragonal phase, in fact, is para-electric. The diffuse phase transition (DPT) of the NBT crystal, therefore, is from a paraelectric and ferroelastic tetragonal phase to a ferroelectric and ferroelastic rhombohedral phase. The crystallographic supergroup-subgroup relationships in the ferroic phase transitions of NBT crystals are discussed.     

Dielectric Properties and Microstructure of Nb-Co Codoped BaTiO3–(Bi0.5Na0.5)TiO3 Ceramics

X-ray diffractometry, scanning electron microscopy, transmission electron microscopy, and an impedance analyzer were used to examine the Nb–Co codoping effects on the densification, crystalline phase, microstructure development, and dielectric–temperature characteristics of BaTiO₃–(Bi_0.5Na_0.5)TiO₃ ceramics. The results indicate that the Curie temperature shifted to a higher temperature (above 140°C) by adding BNT. The dielectric constant–temperature (ɛ– T ) curve broadened at the Curie temperature due to the small grain size (0.3–0.4 μm). A core-shell structure was developed, which is helpful to flatten the ɛ– T curve of BaTiO₃ ceramics at high temperatures.     

Preparation and Characterization of Relaxor Ferroelectric 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 by a Polymerizable Complex Method

A modified polymerizable complex (PC) method for the preparation of the relaxor ferroelectric 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) ceramics has been developed using a novel water-soluble Nb precursor. The effects of Pb content and sintering temperature on the structure, morphology, composition, and electrical properties of PMN–PT powders and ceramics were investigated systematically. It was found that the modified PC method could effectively reduce the initial crystallization temperature of the perovskite phase to 500°C. For PMN–PT samples with 15% excess Pb content sintered at 600°C for 2 h, the 87% perovskite phase can be achieved, which is much higher than that in conventional solid-state reactions and other solution-based methods at the same temperature. On further increasing the sintering temperature to 1100°C, the perovskite phase content basically remains constant. This is attributed to the Pb-deficient pyrochlore phase formation. On increasing the sintering temperature to 1250°C, the dielectric constant and remnant polarization of PMN–PT ceramics significantly improved due to the larger grain sizes, enhanced density, and the decreasing pyrochlore phase. PMN–PT ceramics with a 98.5% content of the perovskite phase have been fabricated at 1250°C. It displays typical ferroelectric relaxor characteristics with a remnant polarization of 18 μC/cm², a coercive field of 9.6 kV/cm, a piezoelectric coefficient of d ₃₃=360 pC/N, and room-temperature and maximum dielectric constants of 3600 and 10 500 at 1 kHz, respectively.     

Phase Relations in (Pb,La)Zr0.65Ti0.35O3

Low-temperature phase relations in (Pb,La)Zr_0.65Ti_0.35O₃ ceramics were determined as a function of La content and temperature. Dielectric and piezoelectric measurements and X-ray data were used to locate and identify phase transitions. The FE₁-FE₂ transition between rhombohedral ferroelectric phases occurs at higher temperatures as the La eontent is increased. For x >4, where x is the atom % La substituted for Pb, a phase region exists between the paraelectric and ferroelectric states. Dielectric data suggest that this region is antiferroelectric. For 6< x <9 a field-induced phase transition accompanies poling. Poled material with x ∼8 exhibits unusual mechanical properties.     

Alkoxide Route to La0.5Sr0.5CoO3 Films and Powders

An all-alkoxide route to films and nano-phase powders of the La_0.5Sr_0.5CoO₃ perovskite is described. To our knowledge, this is the first purely alkoxide-based route to (La_{1− x} Sr _x )CoO₃, and it yields phase-pure and elementally homogeneous perovskite at 700°C by heating at 2°C/min. At 700°C, a cubic unit cell was obtained with a _c=3.853Å, and after further heating to 1000°C, a rhombohedral cell could be indexed: a _r=5.417 Å, α_r=59.94°. Ninety to 130 nm thick films of La_0.5Sr_0.5CoO₃ were obtained by spin coating. The gel-to-oxide conversion was studied in some detail, using thermo-gravimetric analysis, differential scanning calorimetry, powder X-ray diffraction, IR spectroscopy, and transmission electron microscope equipped with an energy-dispersive X-ray spectrometer.     

Phase Transition and Ferroelectric Characteristics of Pb[(Mg1/3Nb2/3)1-xTix]O3 Ceramics Modified with La(Mg2/3Nb1/3)O3

The effects of 0–5 mol% addition of La(Mg_2/3Nb_1/3)O₃ (LMN) on the phase transition and ferroelectric behaviors of Pb[(Mg_1/3Nb_2/3)_1-xTi_x]O₃ (PMNT) ceramics with compositions near the morphotropic phase boundary (MPB) were studied. An evolution of structure from rhombohedral to tetragonal was found with increasing PbTiO₃ (PT) content across the MPB (at ∼32.5 mol% PT), and a coexistence of both rhombohedral and tetragonal phases was also found at the MPB. The dual-phase field extended toward the lower PT content side of the MPB, and, moreover, the rhombohedrality or tetragonality was reduced, especially for the compositions near the MPB, by the addition of La in PMNT. The ferroelectric transition was found to change from normal to diffuse as the La content increased and the compositions became more rhombohedral. In accordance with the structural evolution, the change of remanent polarization ( P _r) and coercive field ( E _c) also became gradually indistinct, and both P _r and E _c were reduced. For compositions near the MPB, both PMNT and La-modified PMNT had a similar electromechanical factor ( k _p) in a range around 0.55–0.60, but the mechanical quality factor ( Q _m) was significantly reduced for the La-modified PMNT. The piezoelectric coefficient ( d ₃₃), however, was largely improved with increasing La content in PMNT of compositions at MPB. A high value of d ₃₃∼ 815 pC/N was obtained for the 5-mol%-La-modified ceramics, but it was associated with a low value of Q _m.     

Thermal Expansion and Athermal Phase Transition of Y4AI2O9 Ceramics

Thermal expansion of Y₄A1₄O₉ ceramics prepared at 1600° and 1800°C was measured from room temperature to 1500°C in air. Volume changes at the phase transition of Y₄A1₂O₉, along with thermal hysteresis, were observed around 1400°C. The volume of the high-temperature phase was about 0.5% lower than that of the low-temperature phase. The hysteresis width for the sample prepared at 1600°C was 56°C, wider than that (14°C) for the sample prepared at 1800°C. The averages of phase transition start temperatures on heating and on cooling for these samples were, however, almost the same at 1377°C. The phase transitions did not occur at fixed temperatures, and the proportions of the high-temperature phase and the low-temperature phase did not change with time as long as the temperature remained constant ( athermal character). The sample prepared at 1800°C also showed another thermal hysteresis behavior from room temperature to about 1000°C.     

Crystal Chemistry and Dielectric Properties in the Systems BaTiO3-UO2 and BaTiO3-BaUO3

Polycrystalline barium titanate fired in nitrogen at 1300° to 1400°C accommodates up to 3 mole % UO₂ in solid solution; its structure is then cubic at room temperature. With BaUO₃ additions the structure becomes disordered and quasi-cubic. In air, about 1 mole % UO₂ goes into solid solution in BaTiO₃ but the structure remains tetragonal. Diffraction peaks of a new phase, possibly a ternary oxide of barium, uranium, and titanium, appear in patterns of specimens containing more than 2 mole % UO₂. The dielectric constant of BaTiO₃ ceramics fired in air, steam, or oxygen increases with up to about 0.5 mole % UO₂ but declines rapidly above this level. The dielectric constant of BaUO₃ is about two orders of magnitude lower than that of BaTiO₃, and additions of BaUO₃ invariably lower the dielectric constant of BaTiO₃.     

Double Hysteresis Loop and Aging Effect in K0.5Na0.5NbO3–K5.4Cu1.3Ta10O9 Lead-Free Ceramics

In this work, the double-loop-like characteristics of K_0.5Na_0.5NbO₃+ x mol% K_5.4Cu_1.3Ta₁₀O₉ ceramic and its relationships with the transition temperature, aging, and switching have been investigated. Our results reveal that the phase transition temperature is an important parameter determining the aging requirement for the ceramics to exhibit the double-loop-like characteristics. For a ceramic with a high transition temperature, e.g. the ceramic with x =0.75 (tetragonal–orthorhombic phase temperature ∼206°C), the vacancies can migrate during the crystal transformation and settle in a distribution with the same symmetry as the crystal after the transformation. As a result, defect dipoles along the polarization direction are formed and provide restoring forces to reverse the switched polarizations, and thus producing a double polarization hysteresis ( P – E ) loop. On the other hand, aging is required for a ceramic with a low transition temperature, e.g. aging at 80°C for 30 days is required for the ceramic with x =1.5 (transition temperature ∼175°C). Our results also reveal that the defect dipoles can be switched under a slow-switching electric field (<1 Hz) or at high temperatures (>100°C), thus leading to an opening of the double P – E loop.