AlxGa1—xAs外延层中Si平面掺杂的SIMS研究

利用二次离子质谱系统地研究了生长温度，Ａｌ组分Ｘ值和Ａｓ４夺强对Ｓｉδ掺杂ＡｌｘＧａ１－ｘＡｓ的ＳＩＭＳ深度剖面，Ｓｉ原子表面分凝和向衬底扩散的影响。实验发现，在外延生长Ｓｉδ掺杂ＡｌｘＧａ１－ｘＡｓ时，随着生长温度的提高或Ａｌ组份Ｘ值增加，Ｓｉ掺杂分布ＳＩＭＳ峰都非对称展宽，表面分凝作用加强，但不影响Ｓｉ原子的扩散，因此ＳＩＭＳ剖面的展宽与扩散无关。     

分子束外延生长GaAs中δ掺杂研究

利用二次离子质谱（ＳＩＭＳ）和电化学剖面Ｃ－Ｖ方法研究了生长温度对ＧａＡｓ中理想Ｓｉδ掺杂的结构的偏离和掺杂原子电微活效率的影响。实验发现，外延生长Ｓｉδ掺杂，ＧａＡｓ时，随着生长温度的升高，Ｓｉ掺杂分布ＳＩＭＳ峰非对称展宽。表面分凝作用加强，但不影响Ｓｉ原子扩散。另外，Ｓｉ施主电激活效率随着生长温度的提高而增大。     

Ga－Al－As－Si系统中Si的两性掺杂行为的研究

对Ｓｉ在电液相外延Ｇａ－Ａｌ－Ａｓ－Ｓｉ系统中的两性掺杂行为进行了研究。提出了一种恒温生长Ｇａ＿（１－ｘ）Ａｌ＿ｘＡｓ：Ｓｉｐ－ｎ结的新方法，对这种ｐ－ｎ结的成因作了定性的解释，并对这种ｐ－ｎ结的电特性加以观察。     

δ－掺杂GaAs／AlxGa_（1－x）As二维电子气结构材料的GSMBE生长与特性

本文用ＧＳＭＢＥ技术生长纯度ＧａＡｓ和δ－掺杂ＧａＡｓ／Ａｌ_ｘＧａ_（１－ｘ）Ａｓ结构二维电子气材料并对其电学性能进行了研究。对于纯度ＧａＡｓ的ＧＳＭＢＥ生长和研究，在低掺Ｓｉ时，载流子浓度为２×１０~（１４）ｃｍ~（－３），７７Ｋ时的迁移率可达８４，０００ｃｍ~２／Ｖ．ｓ。对于用ＧＳＭＢＥ技术生长的δ－掺杂ＧａＡｓ／Ａｌ_ｘＧａ_（１－ｘ）Ａｓ二维电子气材料，在优化了材料结构和生长工艺后，得到了液氮温度和６Ｋ迁移率分别为１７３，５８３ｃｍ~２／Ｖ．５和７．６７×１０~５ｃｍ~２／Ｖ．ｓ的高质量ＧａＡｓ／Ａｌ_ｘＧａ_（１－ｘ）Ａｓ二维电子气材料。     

铝镓砷中硅δ掺杂的SIMS分析

评述了国际上δ掺杂样品ＳＩＭＳ分析的现状，研究了相关的基础实验技术，讨论了分析硅δ掺杂的ＡｌＧａＡｓ样吕时，选择高质量分辨及对不同一次离子参量下相对灵敏度因子进行校准的必须性，考察了一次束的展宽效应的δ掺杂层位置的微分飘移，对硅δ掺杂的ＡｌＧａＡｓ样品用Ｏ２＾＋源进行了定量分析，并对结果作了讨论。     

MOCVD外延生长Ga_(1-x)Al_xAs_(1-y)Sb_y半导体薄膜气固平衡和人工神经网络预报

本文研究了ＭＯＣＶＤ外延生长Ｇａ１－ｘＡｌｘＡｓ１－ｙＳｂｙ半导体薄膜的生长条件与外延层组成的关系，并用人工神经网络法总结有关气固平衡规律。结果表明，用气相组成，载气流量和生长温度等影响外延层组成的主要参数作为人工神经网络的输入，以固相Ｇａ１－ｘＡｌｘＡｓ１－ｙＳｂｙ中的Ａｌ和Ｓｂ的含量ｘ、ｙ作为输出，训练的人工神经网络可以预报固相组成ｘ、ｙ，得到满意结果。     

MOCVD外延生长Ga1—xAlAs1—ySby半导体薄膜气固平衡和人工神经网络预报

本文研究了ＭＯＣＶＤ外延生长Ｇａ１－ｘＡｌｘＡｓ１－６Ｓｂｙ半导体薄膜的生长条件与外延层组成的关系，并用人工神经网络法总结有关气固平衡规律。结果表明，用气相组成，载气流量和生长等影响外延层组成的主要参数作为人工神经网络的输入，以固相Ｇａ１－ｘＡｌｘＡｓ１－ｙＳｂｙ中的Ａｌ和Ｓｂ的含量ｘ、ｙ作为输出，训练的人工神经网络可以预报固相组成ｘ、ｙ，得到满意结果。     

国产金属有机化合物TMGa,TMAl,TMIn和TMSb的MOVPE鉴定

利用我们研制的常压ＭＯＶＰＥ设备对国产ＴＭＧａ、ＴＭＡｌ、ＴＭＩｎ和ＴＭＳｂ进行了鉴定，为此分别生长了ＧａＡｓ、ＡｌＧａＡｓ、ＩｎＰ、ＧａＳｂ外延层和ＧａＡｓ／ＡｌＡｓ、ＧａＳｂ／ＩｎＧａＳｂ超晶格和ＧａＡｓ／ＡｌＧａＡｓ量子阱结构。表征材料纯度的７７Ｋ载流予迁移率分别达到ＧａＡｓ：μ＿ｎ＝５６６００ｃｍ￣２／Ｖ·ｓ，Ａｌ＿（０．２５）Ｇａ＿（０．７５）Ａｓ：μ＿ｎ＝５１６０ｃｍ￣２／Ｖ·ｓ，ＩｎＰ：μ＿ｎ＝６５３００ｃｍ￣２／Ｖ·ｓ，ＧａＳｂ：μ＿ｐ＝５０７６ｃｍ￣２／Ｖ·ｓ。由１０个周期的ＧａＡｓ／ＡｌＡｓ超晶格结构组成的可见光区布拉格反射器已观测到很好的反射光谱和双晶Ｘ射线回摆曲线上高达±２０级的卫星峰。ＧａＡｓ／Ａｌ＿（０．３５）Ｇａ＿（０．６５）Ａｓ量子阱最小阱宽为１０，在ｌｉＫ下由量子尺寸效应导致的光致发光峰能量移动为３９０ｍｅＶ，其线宽为１２ｍｅＶ。这些结果表明上述金属有机化合物已达到较高质量。     

(Ca,Mg)-α-Sialon的致密化,形成特性和显微结构

利用热压工艺制备了组份为（Ｃａ,Ｍｇ）ｘＳｉ１２－３ｘＡｌ３ｘＯｘＮ１６－ｘ（ｘ＝０．３、０．６、１．０和１．４）的（Ｃａ,Ｍｇ）－α－Ｓｉａｌｏｎ。研究结果发现,当ｘ≥１．０时,材料的主晶相为α－Ｓｉａｌｏｎ和含Ｍｇ的ＡｌＮＡ多型体。多型体的含量随ｘ值的增加而变大。以复合添加剂取代单一添加剂,不仅改善了α－Ａｉａｌｏｎ的烧结性能,ＴＥＭ和ＥＤＡＸ的结果还进一步表明添加的Ｃａ＾＋＋离子进入α－Ｓｉ     

n型GaSb,InGaAsSb的MBE生长和特性研究

本文报导了非故意掺杂ＩｎＧａＡｓＳｂ本底浓度的降低和掺Ｔｅｎ型ＧａＳｂ和ＩｎＧａＡｓＳｂ的ＭＢＥ生长与特性的研究结果。结果表明，通过生长工艺的优化，ＧａＳｂ和ＩｎＧａＡｓＳｂ的背景空穴浓度可分别降至１．１×１０~（１６）ｃｍ~（－３）和４×１０~（１６）ｃｍ~（－３），室温空穴迁移率分别为９４０ｃｍ２／ｖ．ｓ和２６０ｃｍ~２／ｖ．ｓ。用Ｔｅ作ｎ型掺杂剂，可获得载流子浓度在１０~（１６）～１０~（１８）ｃｍ~（－３）的优质ＧａＳｂ和ＩｎＧａＡｓＳｂ外延层，所研制的材料已成功地制备出Ｄ_λ~＊＝４×１０~（１０）ｃｍＨｚ~（１／２）／Ｗ的室温ＩｎＧａＡｓＳｂ红外探测器和室温脉冲ＡｌＧａＡｓＳｂ／ＩｎＧａＡｓＳｂ双异质结激光器。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from