Characterization and Properties of Poly(methyl methacrylate)/Graphene,Poly(methyl methacrylate)/Graphene Oxide and Poly(methyl methacrylate)/p-Phenylenediamine-Graphene Oxide Nanocomposites

In this study, poly(methyl methacrylate)/p-phenylenediamine-graphene oxide, poly(methyl methacrylate)/graphene, and poly(methyl methacrylate)/graphene oxide nanocomposite series were prepared using simple solution blending technique. In poly(methyl methacrylate)/p-phenylenediamine-graphene oxide series, graphene oxide modified with p-phenylenediamine was used to improve its dispersion and interfacial strength with matrix. Morphology study of poly(methyl methacrylate)/p-phenylenediamine-graphene oxide nanocomposite revealed better dispersion of p-phenylenediamine-graphene oxide flakes and gyroid patterning of poly(methyl methacrylate) over the filler surface. Due to nonconducting nature of graphene oxide, there was no significant variation in the thermal or electrical conductivity of these nanocomposites. Thermal conductivity of poly(methyl methacrylate)/p-phenylenediamine-graphene oxide 1.5 was 1.16 W/mK, while the electrical conductivity was found to be 2.3 × 10^?3 S/cm.     

Shape Memory and Physical Properties of Composites of Polyethylene Oxide/Poly(Propylene Glycol)-Block-Poly(Ethylene Glycol)-Block-Poly(Propylene Glycol)/2,4-Toluene Diisocyanate,Polypyrrole, and Modified MWCNT

Structural variation and its influence on morphology, mechanical, thermal, and electrical conductivity properties of polyethylene oxide/poly(propylene glycol)-block-poly(ethylene glycol)-block-poly(propylene glycol)/2,4-toluene diisocyanate/polypyrrole (PEO/P(P-E-P)G/TDI/PPy) blends and nanocomposites with varying PPy content were reported. The chemical and fundamental linkages were confirmed by FTIR. SEM micrographs demonstrated homogeneous PEO/P(P-E-P)G/TDI/PPy blend formation and globular morphology for nanocomposites. The mechanical and DSC parameters were found to increase systematically with increasing PPy content in blend films. While for nanocomposites, better results were observed for 0.1% PPy content. Maximum electrical conductivity and good shape recovery of 94% was obtained for the nanocomposite with 1% PPy content.     

Poly(ethylene oxide)/poly(methyl methacrylate) blends: Influence of tacticity of poly(methyl methacrylate) on blend structure and miscibility

The influence of different configurations of poly(methyl methacrylate) on the miscibility and superstructure of poly(ethylene oxide)/poly(methyl methacrylate) (PEO/PMMA) blends was examined using small-angle X-ray scattering and differential scanning calorimetry. The blends prepared by solution casting were isothermally crystallized at 48°C. The miscibility, the melting behaviour, the glass transition temperature and the structural parameters of the blends were strongly dependent on the tacticity and blend composition. The small-angle X-ray intensity profiles were analysed using a recently developed methodology. For the poly(ethylene oxide)/atactic poly(methyl methacrylate) (PEO/APMMA) and poly(ethylene oxide)/syndiotactic poly(methyl methacrylate) (PEO/SPMMA) blends, the long period and the amorphous and transition region thicknesses increased with increase of PMMA content, whereas for the poly(ethylene oxide)/isotactic poly(methyl methacrylate) (PEO/IPMMA) blends they are independent of composition. The structural properties of the blends were attributed to the presence of non-crystallizable material in the interlamellar or interfibrillar regions, depending on PMMA tacticity. From the glass transition and melting temperatures, it has been supposed that one homogeneous amorphous phase is present in the case of PEO/APMMA and PEO/SPMMA blends and that the PEO/IPMMA amorphous system is phase-separated. The free-volume contribution to the energy of mixing for the various tactic PMMAs is hypothesized to be responsible for the difference in mixing behaviour.     

Investigation of electrical,mechanical, and thermal properties of functionalized multiwalled carbon nanotubes‐reduced graphene Oxide/PMMA hybrid nanocomposites

Electrical, mechanical, and thermal properties of the poly(methyl methacrylate) (PMMA) composites containing functionalized multiwalled carbon nanotubes (f‐MWCNTs) and reduced graphene oxide (rGO) hybrid nanofillers have been investigated. The observed electrical percolation threshold of FHC is 0.8 wt% with maximum conductivity of 1.21 × 10^?3 S/cm at 4 wt% of f‐MWCNTs. The electrical transport mechanism and magneto resistance studied of hybrid composites have also been investigated. Progressive addition of f‐MWCNTs in rGO/PMMA composite results increase in mechanical (tensile strength and Young's modulus) and thermal (thermal stability) properties of f‐MWCNTs‐rGO/PMMA hybrid nanocomposites (FHC). The increased mechanical properties are due to the efficient load transfer from PMMA matrix to f‐MWCNTs and rGO through better chemical interaction. The strong interaction between PMMA and f‐MWCNTs‐rGO in FHC is the main cause for improved thermal stability. POLYM. ENG. SCI., 59:1075–1083, 2019. © 2019 Society of Plastics Engineers     

Highly filled multilayer thermoplastic/graphene conducting composite structures with high strength and thermal stability for electromagnetic interference shielding applications

Polyvinyl chloride (PVC)/graphene and poly(methyl methacrylate) (PMMA)/graphene nanocomposites were made by solution casting technique with graphene weight fractions of 1, 5, 10, 15, and 20%. Multilayer structures of the composites were made by hot compression technique to study their electromagnetic interference shielding effectiveness (EMI SE). Tensile strength, hardness, and storage modulus of the nanocomposites were studied in relation with graphene weight fraction. There has been a substantial increase in the electrical conductivity and EMI SE of the composites with 15–20% filler loading. Differential thermal analysis of the composites shows improved thermal stability with an increase in graphene loading. PMMA/graphene composites have better thermal stability, whereas PVC/graphene composites have superior mechanical properties. About 2 mm thick multilayer structures of PMMA/graphene and PVC/graphene composites show a maximum EMI SE of 21 dB and 31 dB, respectively, in the X band at 20 wt % graphene loading. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47792.     

Impact,Thermal, and Morphological Properties of Poly(Lactic Acid)/Poly(Methyl Methacrylate)/Halloysite Nanotube Nanocomposites

Poly(lactic acid)/poly(methyl methacrylate) blends containing halloysite nanotube (2 and 5 phr) and epoxidized natural rubber (5–15 phr) were prepared by melt mixing. The impact strength of poly(lactic acid)/poly(methyl methacrylate) blend was slightly improved by the addition of halloysite nanotube. Adding epoxidized natural rubber further increased the impact strength of poly(lactic acid)/poly(methyl methacrylate)/halloysite nanotube nanocomposite. Single T_g of poly(lactic acid)/poly(methyl methacrylate) is observed and this indicates that poly(lactic acid)/poly(methyl methacrylate) blend is miscible. The addition of halloysite nanotube into poly(lactic acid)/poly(methyl methacrylate) slightly increased the T_g of the blends. The epoxidized natural rubber could encapsulate some of the halloysite nanotube and prevent the halloysite nanotube from breaking into shorter length tube during the melt shearing process.     

Reduced graphene oxide reinforced PET/PBT nanocomposites: Compatibilization and characterization

This research work focused on the effects of different compatibilizers on the properties of reduced graphene oxide (rGO) reinforced poly(ethylene terephthalate) (PET)/poly(butylene terephthalate) (PBT) nanocomposites. The samples were prepared via melt compounding and injection molding methods. The Joncryl and glycidyl isooctyl polyhedral oligomeric silsesquioxane (GPOSS) were used as compatibilizers at different loading levels (0.5%-4%). The structural, thermal, mechanical, morphological, and electrical properties of the nanocomposites were investigated. The Fourier transform infrared analysis results revealed that no significant interaction was observed when GPOSS was added. On the other hand, there were more obvious changes in the peaks of the nanocomposite containing Joncryl. The thermal results showed that the compatibilizer addition caused small changes while rGO addition did not considerably affect the thermal stability of blend. The glass transition temperature of the nanocomposite significantly decreased with the addition of GPOSS. The tensile test indicated that compatibilizers improved the mechanical performance of PET/PBT/rGO nanocomposite.     

Properties of Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline Conductive Films: The Effect of Poly(ethylene glycol) Diglycidyl Ether

The effect of polyaniline and poly(ethylene glycol) diglycidyl ether on tensile properties, morphology, thermal degradation, and electrical conductivity of poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films was studied. The poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films were prepared using a solution casting technique at room temperature until a homogeneous solution was produced. Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline/poly(ethylene glycol) diglycidyl ether conductive films exhibit higher electrical properties, tensile strength, modulus of elasticity but lower final decomposition temperature than poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films. Scanning electron microscopy morphology showed that the polyaniline more widely dispersed in the poly(vinyl chloride)/poly(ethylene oxide) blends with the addition of poly(ethylene glycol) diglycidyl ether as surface modifier.     

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites with improved thermal and mechanical properties

Layer‐structured poly(vinyl alcohol)/graphene oxide nanocomposites in the form of films are prepared by simple solution processing. The structure and properties of these nanocomposites are studied using X‐ray diffractions, scanning electron microscopy, Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. The results indicate that graphene oxide is dispersed on a molecular scale and aligned in the poly(vinyl alcohol) matrix, and there exists strong interfacial interactions between both components, which are responsible for the significant improvement in the thermal and mechanical properties of the nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Investigation of thermal,mechanical and electrochemical properties of nanocomposites based on CuO modified poly(vinyl chloride)/poly(methyl methacrylate) blend

The preparation of binary polymer blend nanocomposites with different nanomaterials is a relatively new approach to achieve desired physical, thermal, mechanical, and electrochemical properties because it has the collective effects of both polymer blending and fillers. Transition metal oxides constitute a large class among those fillers because the precursors for metal oxides are abundantly available. However, very few studies have been accomplished on incorporating transition metal oxides into binary polymer blends. In this project, cuprous oxide (CuO) nanoparticles (NPs) with a crystallite size of 24.95 nm were incorporated into poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blend, and thin films of the nanocomposites were obtained through a solution casting technique. Scanning electron microscopy, X‐ray diffraction, universal testing machine testing, thermogravimetric analysis, and cyclic voltammetry were used to study morphological, crystalline, mechanical, thermal, and electrochemical properties of the nanocomposites. Scanning electron micrographs showed that the blend was completely miscible and CuO NPs were well dispersed within the matrix. Mechanical properties greatly improved with each wt% addition of CuO NPs. Thermogravimetric analysis thermograms revealed a two‐stage degradation for neat PVC/PMMA blend and CuO/PVC/PMMA. Cyclic voltammetry results indicated a free electron transfer in neat blend that further improved with the incorporation of increasing percentage of CuO NPs. J. VINYL ADDIT. TECHNOL., 23:80–85, 2017. © 2015 Society of Plastics Engineers     

Graphene Nanoplatelets as Novel Reinforcement Filler in Poly(lactic acid)/Epoxidized Palm Oil Green Nanocomposites: Mechanical Properties

Graphene nanoplatelet (xGnP) was investigated as a novel reinforcement filler in mechanical properties for poly(lactic acid) (PLA)/epoxidized palm oil (EPO) blend. PLA/EPO/xGnP green nanocomposites were successfully prepared by melt blending method. PLA/EPO reinforced with xGnP resulted in an increase of up to 26.5% and 60.6% in the tensile strength and elongation at break of the nanocomposites respectively, compared to PLA/EPO blend. XRD pattern showed the presence of peak around 26.5° in PLA/EPO nanocomposites which corresponds to characteristic peak of graphene nanoplatelets. However, incorporation of xGnP has no effect on the flexural strength and modulus. Impact strength of PLA/5 wt% EPO improved by 73.6% with the presence of 0.5 wt% xGnP loading. Mechanical properties of PLA were greatly improved by the addition of a small amount of graphene nanoplatelets (<1 wt%).     

Poly(methyl methacrylate) nanocomposites based on graphene oxide: a comparative investigation of the effects of surface chemistry on properties and foaming behavior

The effects of oxygen functional groups and alkyl chains at the surface of graphene oxide (GO) on the thermal stability, mechanical properties and foaming behavior of poly(methyl methacrylate) (PMMA) nanocomposites were investigated. Alkyl‐functionalized GO (GO‐ODA) was prepared by grafting octadecylamine (ODA) on the surface of GO. PMMA/GO and PMMA/GO‐ODA nanocomposite were obtained by solution blending and were foamed using supercritical carbon dioxide (scCO₂). GO‐ODA, with the presence of alkyl chains, showed a better dispersion capability in PMMA matrix than GO with a large amount of oxygen functional groups. In addition, the good dispersion capability increased thermal stability and mechanical strength. In comparison with PMMA/GO samples foamed at 70 °C, PMMA/GO‐ODA nanocomposite foams displayed improved cell structures with higher cell density, smaller cell size and more homogeneous cell size distribution, which results from the strong heterogeneous nucleation due to alkyl chains on the GO surface. The foaming behaviors became more complicated at 80 °C as the GO might be intercalated and exfoliated with the aid of scCO₂, thus further enhancing the heterogeneous nucleation during the foaming process. The results indicated that the surface chemistry of GO was closely related to the properties and foaming behavior of the nanocomposites. © 2016 Society of Chemical Industry     

Effects of compatibilizer type and rubber‐wood sawdust content on the mechanical,morphological, and thermal properties of PVC/LDPE blend

This article aimed to investigate the mechanical, morphological and thermal properties of PVC/LDPE blend with and without the addition of compatibilizers. The effects of LDPE content, compatibilizer type and rubber‐wood sawdust loading on the properties of the blend were evaluated. The experimental results suggested that as the LDPE content was increased the mechanical properties of PVC‐LDPE blend progressively decreased due to poor interfacial adhesion. The continuity and compatibility between PVC and LDPE phases could be improved through three different types of compatibilizers which included chlorinated polyethylene (CPE) poly(methyl‐methacrylate‐co‐butyl acrylate) (PA20) and poly(ethylene‐co‐methacrylate) (Elvaloy). The PA20 was found to be the most suitable compatibilizer for the blend. A radical transfer reaction was proposed in this work to explain the structure and thermal changes of the PVC in PVC‐LDPE blend. The decomposition temperature of PVC in the blend decreased with the loading of the PA20 and the wood sawdust. As the sawdust content was increased the tensile and flexural moduli increased with considerable decreased in the tensile, flexural and impact strength, a slight improvement being achieved if the PA20 was incorporated in the composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 598–606, 2006     

Morphology,thermal, mechanical,and barrier properties of graphene oxide/poly(lactic acid) nanocomposite films

To improve the physical and gas barrier properties of biodegradable poly(lactic acid) (PLA) film, two graphene nanosheets of highly functionalized graphene oxide (0.3 wt% to 0.7 wt%) and low-functionalized graphene oxide (0.5 wt%) were incorporated into PLA resin via solution blending method. Subsequently, we investigated the effects of material parameters such as loading level and degree of functionalization for the graphene nanosheets on the morphology and properties of the resultant nanocomposites. The highly functionalized graphene oxide (GO) caused more exfoliation and homogeneous dispersion in PLA matrix as well as more sustainable suspensions in THF, compared to low-functionalized graphene oxide (LFGO). When loaded with GO from 0.3 wt% to 0.7 wt%, the glass transition temperature, degree of crystallinity, tensile strength and modulus increased steadily. The GO gave rise to more pronounced effect in the thermal and mechanical reinforcement, relative to LFGO. In addition, the preparation of fairly transparent PLA-based nanocomposite film with noticeably improved barrier performance achieved only when incorporated with GO up to 0.7wt%. As a result, GO may be more compatible with hydrophilic PLA resin, compared to LFGO, resulting in more prominent enhancement of nanocomposites properties.     

Thermal‐Insulation,Electrical, and Mechanical Properties of Highly‐Expanded PMMA/MWCNT Nanocomposite Foams Fabricated by Supercritical CO2 Foaming

Foaming behavior of poly(methyl methacrylate) (PMMA)/multi‐walled carbon nanotubes (MWCNTs) nanocomposites and thermally‐insulating, electrical, and mechanical properties of the nanocomposite foams are investigated. PMMA/MWCNT nanocomposites containing various amounts of MWCNTs are first prepared by combining solution and melt blending methods, and then foamed using CO₂. The foaming temperature and MWCNT content are varied for regulating the structure of PMMA/MWCNT nanocomposite foams. The electrical conductivity measurement results show that MWCNTs have little effect on the electrical conductivity of foams with large expansion ratio. Thermal conductivities of both solid and foamed PMMA/MWCNT nanocomposites are measured to evaluate their thermally insulating properties. The gas conduction, solid conduction, and thermal radiation of the foams are calculated for clarifying the effects of cellular structure and MWCNT content on thermal insulation properties. The result demonstrates that MWCNTs endowed foams with enhanced thermal insulation performance by blocking thermal radiation. Moreover, the compressive testing shows that MWCNTs improve the compressive strength and rigidity of foams. This research is essential for optimizing environmentally friendly thermal insulation nanocomposite foams with enhanced thermal‐insulation and compressive mechanical properties.     

Free volume,mobility, and structural relaxations in poly(ethylene oxide)/poly(methyl methacrylate) blends

Time-dependent structural relaxations in a melt-mixed 38/62 vol% poly(ethylene oxide)/atactic poly(methyl methacrylate) blend were studied using several techniques: differential scanning calorimetry, pressure-volume-temperature analysis, positron annihilation lifetime spectroscopy, dynamic mechanical analysis, and solid-state nuclear magnetic resonance. The internal volume (free volume hole size) and the external volume (specific volume) of the blend are found to decrease with aging time. The time scale of the volume changes is the same, suggesting that internal and external volumes can be calculated from each other. Increasing mobility of poly(ethylene oxide), composition fluctuations, and shifting glass transition temperatures are observed upon aging. Phase separation in terms of spinodal decomposition below an upper critical solution temperature occurs within minutes and results in two amorphous phases of different composition. Subsequent crystallization then causes further structural changes.     

Poly(ethylene terephthalate)/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate)/clay nanocomposites: Mechanical properties,optical transparency,and barrier properties

Poly(ethylene terephthalate) (PET)/clay, PET/poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate) (PETG), and PET/PETG/clay nanocomposites were fabricated using the twin‐screw extrusion technique. The spherulitic morphologies, thermomechanical, mechanical, and gas‐barrier properties, as well as the effect of clay on the transparency of the resulting nanocomposites were identified. The clay induced the heterogeneous nucleation of the nanocomposites during the cold crystallization process, thereby increasing the crystallinities and melting temperatures of the resulting nanocomposites. The incorporation of clay increased the storage moduli, Young's moduli, impact strengths, and barrier properties of the PET, PETG, and PET/PETG blend. Regarding the optical transparency, the inclusion of clay can make the crystallizable PET matrix crystalline opaque. However, the amorphous PETG maintained its transparency. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39869.     

Reinforcing effect of amine-functionalized and carboxylated porous graphene on toughness,thermal stability,and electrical conductivity of epoxy-based nanocomposites

Epoxy-based nanocomposites reinforced with nonfunctionalized porous graphene (NPG), carboxylated porous graphene (CNPG), and amine-functionalized porous graphene (ANPG) were investigated with regard to mechanical properties, thermal stability, and electrical conductivity. Nanomaterials were added to the epoxy matrix in varying contents of 0.5, 1, and 2 wt %. Generally, mechanical properties were improved as a result of introducing nanomaterials into the epoxy resin. However, the amelioration of toughness was only observed in functionalized NPGs/epoxy nanocomposites. Field emission scanning electron microscopy images showed that functionalized nanomaterials induced a rougher fracture surface compared to the neat epoxy. Dynamic mechanical analysis along with differential scanning calorimetry confirmed an increment in the glass-transition temperature (T_g) of the reinforced nanocomposites. Also, they proved that functionalization made the epoxy network tougher and more flexible. The electrical conductivity and thermal stability of the epoxy resin were also improved when loaded with nanomaterials. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47475.     

Interface adjustment between poly(ethylene terephthalate) and graphene oxide in order to enhance mechanical and thermal properties of nanocomposites

There is great interest in the use of graphene and derivatives in the production of polymer nanocomposites as it provides improvements in the properties of the materials to which they are associated. Such improvements depend heavily on filler dispersion and the interaction between the nanomaterials and the matrix. This work aimed to study the compatibility of graphene oxide (GO) with a poly(ethylene terephthalate) matrix. For this, graphite was modified using Hummers method, using reaction times of 3 and 6 h. The obtained GO was functionalized with amine, amide, and magnetite groups (FGO). The effects of the oxidation degree, functionalization and concentration of the nanofillers on the dispersion and consequently on the properties of the polymer nanocomposites were evaluated. The nanocomposites were synthesized by the solid–solid deposition method followed by the melt mixing technique. It was observed that lower concentrations of nanofiller associated with the lower degree of oxidation and functionalization improved the interaction of the nanofillers with the matrix, which resulted in better mechanical properties under tensile stresses for strain at break, maximum stress, Young's modulus and toughness. It was also observed that the glass transition and crystallization of nanocomposites increased due to a nucleating effect of the nanofillers.     

Interrelationship of thermal and mechanical properties of poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate)/graphene nanocomposites

In the present work, attempts were made to investigate the thermal and mechanical properties of melt‐processed poly(ethylene terephthalate) (PET)/poly(ethylene 2,6‐naphthalate) (PEN) blends and its nanocomposites containing graphene by using differential scanning calorimetry and tensile test experimenting. The results showed that crystallinity, which depends on a blend ratio, completely disappeared in a composition of 50/50. By introducing graphene to PET, even in low concentrations, the crystallinity of samples increased, while the nanocomposite of PEN indicated reverse behavior, and the crystallinity was reduced by adding graphene. In the case of PET‐rich (75/25) nanocomposite blends, by increasing the nano content in the blend, the crystallinity of the samples was enhanced. This behavior was attributed to the nucleating effect of graphene particles in the samples. From the results of mechanical experiments, it was found in PET‐rich blends that by increasing the PEN/PET ratio, the modulus of samples decreased, whereas in the case of PEN‐rich blends, a slight increment of modulus is seen as a result of the increment of the PEN/PET ratio. The two contradicting behaviors were attributed to the reduction of crystallinity of PET‐rich blends by enhancement of PEN/PET ratio and the rigid structure of PEN chains in PEN‐rich blends. Unlike the different modulus change of PET‐rich and PEN‐rich blends, the nanocomposites of these blends similarly indicated an increment of modulus and characteristics of rigid materials by increasing the nano content. Furthermore, the same behavior was detected in nanocomposites of each polymer (PET and PEN nanocomposites). The alteration from ductile to rigid conduction was related to the impedance in the role of graphene plates against the flexibility of polymer chains and high values of graphene modulus. J. VINYL ADDIT. TECHNOL., 23:210–218, 2017. © 2015 Society of Plastics Engineers