Importance of flow stratification and bubble aggregation in the separation zone of a dissolved air flotation tank

The importance of horizontal flow patterns and bubble aggregation on the ability of dissolved air flotation (DAF) systems to improve bubble removal during drinking water treatment were explored using computational fluid dynamics (CFD) modeling. Both analytical and CFD analyses demonstrated benefits to horizontal flow. Two dimensional CFD modeling of a DAF system showed that increasing the amount of air in the system improved the bubble removal and generated a beneficial stratified horizontal flow pattern. Loading rates beyond a critical level disrupted the horizontal flow pattern, leading to significantly lower bubble removal. The results also demonstrated that including the effects of bubble aggregation in CFD modeling of DAF systems is an essential component toward achieving realistic modeling results.     

The effect of influent temperature variations in a sedimentation tank for potable water treatment--a computational fluid dynamics study

A computational fluid dynamics (CFD) model is used to assess the effect of influent temperature variation on solids settling in a sedimentation tank for potable water treatment. The model is based on the CFD code Fluent and exploits several specific aspects of the potable water application to derive a computational tool much more efficient than the corresponding tools employed to simulate primary and secondary wastewater settling tanks. The linearity of the particle conservation equations allows separate calculations for each particle size class, leading to the uncoupling of the CFD problem from a particular inlet particle size distribution. The usually unknown and difficult to be measured particle density is determined by matching the theoretical to the easily measured experimental total settling efficiency. The present model is adjusted against data from a real sedimentation tank and then it is used to assess the significance of influent temperature variation. It is found that a temperature difference of only 1 degrees C between influent and tank content is enough to induce a density current. When the influent temperature rises, the tank exhibits a rising buoyant plume that changes the direction of the main circular current. This process keeps the particles in suspension and leads to a higher effluent suspended solids concentration, thus, worse settling. As the warmer water keeps coming in, the temperature differential decreases, the current starts going back to its original position, and, thus, the suspended solids concentration decreases.     

Measurement and three-dimensional simulation of flow in a rectangular detention tank

There are two main ways to obtain better knowledge of the hydraulics of ponds, namely measurements and simulations. In this study, the applicability of using three-dimensional simulations as an engineering tool in stormwater pond design was investigated. To do this, three-dimensional simulations were compared with measurements of flow pattern and residence time in a large physical model of a detention tank (13 × 9 × 1 m). The agreement between measurements and simulations concerning both flow pattern and residence time distribution curves was found to be good for high flow rates.     

低温热水地面辐射供暖施工质量问题分析及监理控制

低温热水地面辐射供暖方式因其节能、卫生、不占室内空间等诸多优点,近年来得到了广泛应用,但在施工中仍存在很多不规范及影响工程质量的情况.本文结合施工中存在的一些实际问题予以分析,提出现场监理机构在其施工质量控制中应着重注意的问题.     

低温热水地面辐射供暖施工质量问题分析及监理控制

低温热水地面辐射供暖方式因其节能、卫生、不占室内空间等诸多优点,近年来得到了广泛应用,但在施工中仍存在很多不规范及影响工程质量的情况。本文结合施工中存在的一些实际问题予以分析,提出现场监理机构在其施工质量控制中应着重注意的问题。     

Numerical analysis of air flow, heat transfer, moisture transport and thermal comfort in a room heated by two-panel radiators

A three-dimensional steady-state numerical analysis was performed in a room heated by two-panel radiators. A virtual sitting manikin with real dimensions and physiological shape was added to the model of the room, and it was assumed that the manikin surfaces were subjected to constant temperature. Two different heat transfer coefficients for the outer wall and for the window were considered. Heat interactions between the human body surfaces and the room environment, the air flow, the temperature, the humidity, and the local heat transfer characteristics of the manikin and the room surfaces were computed numerically under different environmental conditions. Comparisons of the results are presented and discussed. The results show that energy consumption can be significantly reduced while increasing the thermal comfort by using better-insulated outer wall materials and windows.