共查询到20条相似文献,搜索用时 46 毫秒
1.
A multi-component NO x-trap catalyst consisting of Pt and K supported on γ-Al 2O 3 was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H 2O and CO 2 on NO x storage. The Al 2O 3 support was shown to have NO x trapping capability with and without Pt present (at 250 °C Pt/Al 2O 3 adsorbs 2.3 μmols NO x/m 2). NO x is primarily trapped on Al 2O 3 in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO x/m 2, and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al 2O 3 catalyst are coordinated on the Al 2O 3 support at saturation. When 5% CO2 was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H2O was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al2O3-based nitrates decreased by 92%. Interestingly, with both 5% CO2 and 5% H2O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al2O3 destabilized the K–CO2 bond; specifically, H2O mitigates the NOx storage capacity losses associated with carboxylate competition. 相似文献
2.
A mean field model, for storage and desorption of NO x in a Pt/BaO/Al 2O 3 catalyst is developed using data from flow reactor experiments. This relatively complex system is divided into five smaller sub-systems and the model is divided into the following steps: (i) NO oxidation on Pt/Al 2O 3; (ii) NO oxidation on Pt/BaO/Al 2O 3; (iii) NO x storage on BaO/Al 2O 3; (iv) NO x storage on Pt/BaO/Al 2O 3 with thermal regeneration and (v) NO x storage on Pt/BaO/Al 2O 3 with regeneration using C 3H 6. In this paper, we focus on the last sub-system. The kinetic model for NO x storage on Pt/BaO/Al 2O 3 was constructed with kinetic parameters obtained from the NO oxidation model together with a NO x storage model on BaO/Al 2O 3. This model was not sufficient to describe the NO x storage experiments for the Pt/BaO/Al 2O 3, because the NO x desorption in TPD experiments was larger for Pt/BaO/Al 2O 3, compared to BaO/Al 2O 3. The model was therefore modified by adding a reversible spill-over step. Further, the model was validated with additional experiments, which showed that NO significantly promoted desorption of NO x from Pt/BaO/Al 2O 3. To this NO x storage model, additional steps were added to describe the reduction by hydrocarbon in experiments with NO 2 and C 3H 6. The main reactions for continuous reduction of NO x occurs on Pt by reactions between hydrocarbon species and NO in the model. The model is also able to describe the reduction phase, the storage and NO breakthrough peaks, observed in experiments. 相似文献
3.
In this paper, the effect of CO 2 and H 2O on NO x storage and reduction over a Pt–Ba/γ-Al 2O 3 (1 wt.% Pt and 30 wt.% Ba) catalyst is shown. The experimental results reveal that in the presence of CO 2 and H 2O, NO x is stored on BaCO 3 sites only. Moreover, H 2O inhibits the NO oxidation capability of the catalyst and no NO 2 formation is observed. Only 16% of the total barium is utilized in NO storage. The rich phase shows 95% selectivity towards N 2 as well as complete regeneration of stored NO. In the presence of CO 2, NO is oxidized into NO 2 and more NO x is stored as in the presence of H 2O, resulting in 30% barium utilization. Bulk barium sites are inactive in NO x trapping in the presence of CO 2·NH 3 formation is seen in the rich phase and the selectivity towards N 2 is 83%. Ba(NO 3) 2 is always completely regenerated during the subsequent rich phase. In the absence of CO 2 and H 2O, both surface and bulk barium sites are active in NO x storage. As lean/rich cycling proceeds, the selectivity towards N 2 in the rich phase decreases from 82% to 47% and the N balance for successive lean/rich cycles shows incomplete regeneration of the catalyst. This incomplete regeneration along with a 40% decrease in the Pt dispersion and BET surface area, explains the observed decrease in NO x storage. 相似文献
4.
Selective catalytic reduction of NO x by C 3H 6 in the presence of H 2 over Ag/Al 2O 3 was investigated using in situ DRIFTS and GC–MS measurements. The addition of H 2 promoted the partial oxidation of C 3H 6 to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO x on Ag/Al 2O 3 surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H 2 on the SCR of NO x by C 3H 6 over Ag/Al 2O 3 catalyst. 相似文献
5.
In this work, a kinetic model is constructed to simulate sulfur deactivation of the NO x storage performance of BaO/Al 2O 3 and Pt/BaO/Al 2O 3 catalysts. The model is based on a previous model for NO x storage under sulfur-free conditions. In the present model the storage of NO x is allowed on two storage sites, one for complete NO x uptake and one for a slower NO x sorption. The adsorption of SO x is allowed on both of these NO x storage sites and on one additional site which represent bulk storage. The present model is built-up of six sub-models: (i) NO x storage under sulfur-free conditions; (ii) SO 2 storage on NO x storage sites; (iii) SO 2 oxidation; (iv) SO 3 storage on bulk sites; (v) SO 2 interaction with platinum in the presence of H 2; (vi) oxidation of accumulated sulfur compounds on platinum by NO 2. Data from flow reactor experiments are used in the implementation of the model. The model is tested for simulation of experiments for NO x storage before exposure to sulfur and after pre-treatments either with SO 2 + O 2 or SO 2 + H 2. The simulations show that the model is able to describe the main features observed experimentally. 相似文献
6.
A series of 1 wt.%Pt/ xBa/Support (Support = Al 2O 3, SiO 2, Al 2O 3-5.5 wt.%SiO 2 and Ce 0.7Zr 0.3O 2, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO 2-TPD. At high temperature (400 °C) in the absence of CO 2 and H 2O, the NO x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO 2 decreased catalyst performances. The inhibiting effect of CO 2 on the NO x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO 2 and H 2O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO 2 was responsible for the loss of NO x storage capacity at 400 °C. Finally, under realistic conditions (H 2O and CO 2) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO 2 competition for the storage sites. 相似文献
7.
A highly dispersed Pt/Al 2O 3 catalyst was used for the selective catalytic reduction of NO x using propene (HC-SCR). Contact with the reaction gas mixture led to a significant activation of the catalyst at temperatures above 523 K. According to CO chemisorption data and HRTEM analysis, Pt particles on the activated catalyst had sintered. The redox behavior of the fresh and sintered catalysts was investigated using Multitrack, a TAP-like pulse reactor. If Pt particles on the catalyst are highly dispersed (average size below 2 nm), only a small part (10%) of the total number of Pt surface sites as determined by CO chemisorption (Pt surf) participates in H 2/O 2 redox cycles (Pt surf,redox) in Multitrack conditions. For a sintered catalyst, with an average particle size of 2.7 nm, the number of Pt surf and Pt surf,redox sites are in good agreement. Similar results were obtained for both catalysts using NO as the oxidant. The low number of Pt surf,redox sites on highly dispersed Pt/Al 2O 3 is explained by the presence of a kinetically more stable—probably ionic—form of Pt---O bonds on all surface sites of the smaller Pt particles, including corner, edge and terrace sites. When the average particle size shifts to 2.7 nm, the kinetic stability of all Pt---O bonds is collectively decreased, enabling the participation of all Pt surface sites in the redox cycles. A linear correlation between the NOx conversion in HC-SCR, and the amount of Ptsurf,redox was found. This suggests that redox-active Pt sites are necessary for catalytic activity. In addition, the correlation could be significantly improved by assuming that Ptsurf,terrace sites of the particles larger than 2.7 nm are mainly responsible for HC-SCR activity in steady state conditions. Implications of these results for the pathway of HC-SCR over Pt catalysts are discussed. 相似文献
8.
The reduction of NO under cyclic “lean”/“rich” conditions was examined over two model 1 wt.% Pt/20 wt.% BaO/Al 2O 3 and 1 wt.% Pd/20 wt.% BaO/Al 2O 3 NO x storage reduction (NSR) catalysts. At temperatures between 250 and 350 °C, the Pd/BaO/Al 2O 3 catalyst exhibits higher overall NO x reduction activity. Limited amounts of N 2O were formed over both catalysts. Identical cyclic studies conducted with non-BaO-containing 1 wt.% Pt/Al 2O 3 and Pd/Al 2O 3 catalysts demonstrate that under these conditions Pd exhibits a higher activity for the oxidation of both propylene and NO. Furthermore, in situ FTIR studies conducted under identical conditions suggest the formation of higher amounts of surface nitrite species on Pd/BaO/Al 2O 3. The IR results indicate that this species is substantially more active towards reaction with propylene. Moreover, its formation and reduction appear to represent the main pathway for the storage and reduction of NO under the conditions examined. Consequently, the higher activity of Pd can be attributed to its higher oxidation activity, leading both to a higher storage capacity ( i.e., higher concentration of surface nitrites under “lean” conditions) and a higher reduction activity ( i.e., higher concentration of partially oxidized active propylene species under “rich” conditions). The performance of Pt and Pd is nearly identical at temperatures above 375 °C. 相似文献
9.
Surface-phase ZrO 2 on SiO 2 (SZrOs) and surface-phase La 2O 3 on Al 2O 3 (SLaOs) were prepared with various loadings of ZrO 2 and La 2O 3, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH 4/CO 2 reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al 2O 3 and Pt/SiO 2 catalysts. CO 2 or CH 4 pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides. The zirconia can be homogeneously dispersed on SiO2 to form a stable surface-phase oxide. The lanthana cannot be spread well on Al2O3, but it forms a stable amorphous oxide with Al2O3. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO2 and Pt/Al2O3 by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO2 and Pt/Al2O3 catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO2 adsorbed on the basic sites of SZrOs and SLaOs. 相似文献
10.
Catalytic performance of Sn/Al 2O 3 catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO 2 had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al 2O 3 (SG) catalyst, and the maximum NO 2 conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO x desorption accompanied with O 2 around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H 2O and SO 2 at low temperature, and the temperature window was also broadened in the presence of H 2O and SO 2, however the NO x desorption and NO conversion decreased sharply on the 300 ppm SO 2 treated catalyst, the catalytic activity was inhibited by the presence of SO 2 due to formation of sulfate species (SO 42−) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al 2O 3 (SG) was not decreased in the presence of large oxygen. 相似文献
11.
The behaviour of a Pt(1 wt.%) supported on CeO 2–ZrO 2(20 wt.%)/Al 2O 3(64 wt.%)–BaO(16 wt.%) as a novel NO x storage–reduction catalyst is studied by reactivity tests and DRIFT experiments and compared with that of Pt(1%)–BaO(15 wt.%) on alumina. The former catalyst, designed as a hydrothermally stable sample, is composed of an alumina modified with Ba ions and an overlayer of ceria-zirconia. The results pointed out that during the calcination barium ions migrates over the surface of the catalyst which thus show a good NO x storage–reduction behaviour comparable with that of Pt–BaO on alumina, although Ba ions result much better dispersed. 相似文献
12.
Dispersing La 2O 3 on δ- or γ-Al 2O 3 significantly enhances the rate of NO reduction by CH 4 in 1% O 2, compared to unsupported La 2O 3. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La 2O 3 precursor used, the pretreatment, and the La 2O 3 loading. The most active family of catalysts consisted of La 2O 3 on γ-Al 2O 3 prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m 2) occurred between the addition of one and two theoretical monolayers of La 2O 3 on the γ-Al 2O 3 surface. The best catalyst, 40% La 2O 3/γ-Al 2O 3, had a turnover frequency at 700°C of 0.05 s −1, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La 2O 3/Al 2O 3 catalysts exhibited stable activity under high conversion conditions as well as high CH 4 selectivity (CH 4 + NO vs. CH 4 + O 2). The addition of Sr to a 20% La 2O 3/γ-Al 2O 3 sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO =4 to the latter Sr-promoted La 2O 3/Al 2O 3 catalyst decreased activity although sulfate increased the activity of Sr-promoted La 2O 3. Dispersing La 2O 3 on SiO 2 produced catalysts with extremely low specific activities, and rates were even lower than with pure La 2O 3. This is presumably due to water sensitivity and silicate formation. The La 2O 3/Al 2O 3 catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications. 相似文献
13.
The NO x storage and reduction functions of a Pt–Ba/Al 2O 3 “NO x storage–reduction” catalyst has been investigated in the present work by applying the transient response and the temperature programmed reaction methods, by using propylene as the reducing agent. It is found that: (i) the storage of NO x occurs first at BaO and then at BaCO 3, which are the most abundant sites following regeneration of catalyst with propylene; (ii) the overall storage process at BaCO 3 is slower than at BaO; (iii) CO 2 inhibits the NO x storage at low temperatures; (iv) the amount of NO x stored up to catalyst saturation at 350 °C corresponds to 17.6% of Ba; (v) the reduction of stored NO x groups is fast and is limited by the concentration of propylene in the investigated T range (250–400 °C); (vi) selectivity to N 2 is almost complete at 400 °C but is significantly lower at 300 °C due to the formation of NO which can be tentatively ascribed to the presence of unselective Pt–O species. 相似文献
14.
A comparison study was carried out on non-thermal plasma (NTP)-assisted selective catalytic reduction (SCR) of NO x by propene over Ag/USY and Ag/Al 2O 3 catalysts. Ag/USY was almost inactive in thermal SCR while it showed obvious activities in NTP-assisted SCR at 100 °C–200 °C. Although the NO x conversion over Ag/Al 2O 3 was also enhanced at 300 °C–400 °C by the assistance of NTP, it was ineffective below 250 °C. The intermediates over Ag/USY and Ag/Al 2O 3 were investigated using in situ DRIFTS method. It was found that key intermediates in HC-SCR, such as NCO, CN, oxygenates and some N-containing organic species were enriched after the assistance of NTP. The differences in the behaviors of above intermediates were not found between these two kinds of catalysts. However, some evidences suggested that different properties of the absorbed NO x species resulted in the distinction of SCR reactions over Ag/USY and Ag/Al 2O 3. TPD profiles of Ag/Al 2O 3 showed that nitrates formed over the catalyst were quite stable at low temperatures, which might occupy the active sites and were unfavorable to SCR reactions. The nitrates over Ag/USY were unstable, among which the unidentate nitrate species is probably contributed to the SCR reactions at low temperatures. 相似文献
15.
Performance of NO x traps after high-temperature treatments in different redox environments was studied. Two types of treatments were considered: aging and pretreatment. Lean and rich agings were examined for a model NO x trap, Pt–Ba/Al 2O 3. These were done at 950 °C for 3 h, in air and in 1% H 2/N 2, respectively. Lean aging had a severe impact on NO x trap performance, including HC and CO oxidation, and NH 3 and N 2O formation. Rich aging had minimal impact on performance, compared to fresh/degreened performance. Deactivation from lean aging was essentially irreversible due to Pt sintering, but Pt remained dispersed with the rich aging. Pretreatments were examined for a commercially feasible fully formulated NO x trap and two model NO x traps, Pt–Ba/Al 2O 3 and Pt–Ba–Ce/Al 2O 3. Pretreatments were done at 600 °C for 10 min, and used feed gas that simulated diesel exhaust under several conditions. Lean pretreatment severely suppressed NO x, HC, CO, NH 3 and N 2O activities for the ceria-containing NO x traps, but had no impact on Pt–Ba/Al 2O 3. Subsequently, a relatively mild rich pretreatment reversed this deactivation, which appears to be due to a form of Pt–ceria interaction, an effect that is well known from early work on three-way catalysts. Practical applications of results of this work are discussed with respect to NO x traps for light-duty diesel vehicles. 相似文献
16.
The adsorption of HCN on, its catalytic oxidation with 6% O 2 over 0.5% Pt/Al 2O 3, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N 2O, NO and NO 2, and some residual adsorbed N-containing species were oxidized to NO and NO 2 during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N 2 and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N 2O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO x in the products. The co-feeding of H 2O and C 3H 6 had little, if any effect on the total HCN conversion, but C 3H 6 addition did increase the conversion to NO and decrease the conversion to NO 2, perhaps due to the competing presence of adsorbed fragments of reductive C 3H 6. Evidence is also presented that introduction of NO and NO 2 into the reactant gas mixture resulted in additional reaction pathways between these NO x species and HCN that provide for lean-NO x reduction coincident with HCN oxidation. 相似文献
17.
The reduction of NO x by hydrogen under lean burn conditions over Pt/Al 2O 3 is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al 2O 3. In this case, although pure H 2 and pure CO are ineffective for NO x reduction under lean burn conditions, H 2/CO mixtures are very effective. With a realistic (1:3) H 2:CO ratio, typical of actual exhaust gas, Pd/Al 2O 3 is significantly more active than Pt/Al 2O 3, delivering 45% NO x conversion at 160 °C, compared to >15% for Pt/Al 2O 3 under identical conditions. The nature of the support is also critically important, with Pd/Al 2O 3 being much more active than Pd/SiO 2. Possible mechanisms for the improved performance of Pd/Al 2O 3 in the presence of H 2+CO are discussed. 相似文献
18.
The effect of different reducing agents (H 2, CO, C 3H 6 and C 3H 8) on the reduction of stored NO x over PM/BaO/Al 2O 3 catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO 2-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H 2 and CO have a relatively high NO x reduction efficiency compared to C 3H 6 and especially C 3H 8 that does not show any NO x reduction ability except at 350 °C over Pd/BaO/Al 2O 3. The type of precious metals affects the NO x storage-reduction properties, where the Pd/BaO/Al 2O 3 catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al 2O 3 catalyst shows a high reduction ability but a relatively low NO x storage capacity. 相似文献
19.
The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al 2O 3 on the selective catalytic reduction (SCR) of NO x with CH 4 under dry and wet reaction stream. After being reduced in H 2 at 350°C, the PtCo bimetallic zeolites showed higher NO to N 2 conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH 4 = 1000 ppm, O 2 = 2%), the NO conversion dropped to zero over Co 2.0Mor at 500°C and GHSV = 30,000 h −1, whereas it is 20% in Pt 0.5Co 2.0Mor. In Pt/Co/Al 2O 3 the NO x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10 −4 s −1 for Pt 0.5Co 2.0Fer, 13 × 10 −4 s −1 for Pt 0.5Co 2.0Mor, 4.33 × 10 −4 s −1 for Pt 0.5Co 2.0ZSM-5 and 0.5 × 10 −4 s −1 for Pt/Co/Al 2O 3. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co 2+ and Pt 2+ at exchange positions. Co° seems not to participate as an active site in the SCR of NO x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO 2 reaction, the activation of CH 4 and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites. 相似文献
20.
Phase changes in high temperature treated (>900 °C) 8 or 20 wt% BaO supported on γ-Al 2O 3 model lean NO x trap (LNT) catalysts, induced by NO 2 and/or H 2O adsorption, were investigated with powder X-ray diffraction (XRD), solid state 27Al magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy, and NO 2 temperature programmed desorption (TPD) experiments. After calcination in dry air at 1000 °C, the XRD and solid state 27Al MAS NMR results confirm that stable surface BaO and bulk BaAl 2O 4 phases are formed for 8 and 20 wt% BaO/Al 2O 3, respectively. Following NO 2 adsorption over these thermally treated samples, some evidence for nanosized Ba(NO 3) 2 particles are observed in the XRD results, although this may represent a minority phase. However, when water was added to the thermally aged samples after NO 2 exposure, the formation of bulk crystalline Ba(NO 3) 2 particles was observed in both samples. Solid state 27Al MAS NMR is shown to be a good technique for identifying the various Al species present in the materials during the processes studied here. NO 2 TPD results demonstrate a significant loss of uptake for the 20 wt% model catalysts upon thermal treatment. However, the described phase transformations upon subsequent water treatment gave rise to the partial recovery of NO x uptake, demonstrating that such a water treatment of thermally aged catalysts can provide a potential method to regenerate LNT materials. 相似文献
|