Oil-Lubricated Fretting Behaviors of 304 Stainless Steels under Different Fretting Strokes and Normal Loads

The influence of oil lubrication on the fretting wear behaviors of 304 stainless steel flat specimens under different fretting strokes and normal loads has been investigated. The results proved that fretting regimes and fretting wear behaviors of 304 stainless steels were closely related to the fretting conditions. In general, the increase in normal load could increase wear damage during sliding wear. However, according to the results, a significant reduction in wear volume and increase in friction coefficient was observed when the normal load was increased to critical values of 40 and 50 N at a fretting stroke of 50 μm due to the transformation of the fretting regime from a gross slip regime to partial slip regime. Only when the fretting stroke further increased to a higher value of 70 μm at 50 N, fretting could enter the gross slip regime. There was low wear volume and a high friction coefficient when fretting was in the partial slip regime, because oil penetration was poor. The wear mechanisms were fatigue damage and plastic deformation. There was high wear volume and low friction coefficient when fretting was in the gross slip regime, because the oil could penetrate into the contact surfaces. Unlike the wear mechanisms in the partial slip regime, fretting damage of 304 stainless steels was mainly caused by abrasive wear in the gross slip regime.     

Frequency effects in fretting wear

The effect of frequency of vibration on fretting wear has been investigated in the 10 – 1000 Hz range with additional experiments at 20 000 Hz. Fretting tests were performed with two materials, a low carbon steel (AISI 1018) and an austenitic stainless steel (AISI 304). The experiments showed that two cases of fretting contact can be distinguished and related to the displacement amplitude. If the amplitude is low, the contact situation is characterized by partial stick at the interface. At these conditions the wear rate (measured as the volume of material removed per cycle) is little affected by frequency. However, in low amplitude fretting material damage by surface degradation and fatigue crack initiation is usually of more concern than the actual wear itself. Both of these parameters are found to be greatly accelerated by an increase in frequency. In high amplitude fretting, in contrast, gross slip occurs at the interface and wear becomes the dominant damage mode. At these conditions variations in frequency appear to have little effect on fretting wear and related mechanisms. Therefore, in the case of fretting at high displacement amplitudes, it may be possible to apply high frequency fretting to obtain accelerated testing conditions.     

Fretting wear mechanisms of Zircaloy-4 and Inconel 600 contact in air

The fretting wear behavior of the contact between Zircaloy-4 tube and Inconel 600, which are used as the fuel rod cladding and grid, respectively, in PWR nuclear power plants was investigated in air. In this study, number of cycles, slip amplitude and normal load were selected as the main factors of fretting wear. The results indicated that wear increased with load, slip amplitude and number of cycles but was affected mainly by the slip amplitude. SEM micrographs revealed the characteristics of fretting wear features on the surface of the specimens such as stick, partial slip and gross slip which depended on the slip amplitude. It was found that fretting wear was caused by the crack generation along the stick-slip boundaries due to the accumulation of plastic flow at small slip amplitudes and by abrasive wear in the entire contact area at high slip amplitudes.     

High temperature fretting wear behavior of WC-25Co coatings prepared by D-gun spraying on Ti-Al-Zr titanium alloy

Detonation gun (D-gun) spraying is one of the most promising spraying techniques for producing wear-resistance coatings. A thick layer (about 0.3 mm thickness) of WC-25Co with high hardness was covered on Ti-Al-Zr titanium alloy by D-gun spraying and the fretting wear behavior of WC-25Co coatings was studied experimentally on a high precision hydraulic fretting wear test rig. An experimental layout was designed to perform fretting wear tests at elevated temperatures from room temperature (25 °C) to 400 °C in ambient air. In the tests, a sphere (Si₃N₄ ceramic ball) was designed to rub against a plane (Ti-Al-Zr titanium alloy with or without WC-25Co coatings). It was found that the fretting running regimes of WC-25Co coatings were obviously different from those of Ti-Al-Zr titanium alloy. The mixed fretting regime disappeared in WC-25Co coatings, and the boundaries in the running condition fretting map (RCFM) showed hardly any change as temperature increased. The worn scars were examined using a laser confocal scanning microscope (LCSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The results showed that the coefficients of friction (COF) of WC-25Co coatings at elevated temperatures were nearly constant in the partial slip regime and very low in the steady state. The fretting damage of the coatings was very slight. In the slip regime, the WC-25Co coatings exhibited a good wear resistance, and the wear volume of the coatings obviously decreased with increasing tested temperature. The fretting wear mechanisms of WC-25Co coatings were delamination, abrasive wear and oxidation wear at elevated temperature. The oxide debris layer formed at higher temperature was denser and thicker on top of WC-25Co coatings, thus providing more surface protection against fretting wear, which played an important role in the low fretting wear of the coatings.     

On the fretting wear mechanism of Zr-alloys

Zirconium alloys are highly desirable in nuclear applications due to their transparency to thermal energy neutrons and for their high corrosion resistance. The main objective of this study is to investigate the fretting wear mechanism of Zr–2.5%Nb alloy. The experimental work was carried out in air at 265 °C, using a specially designed fretting wear tribometer. The transfer of material, the change in the wear volume and the maximum wear depth with the number of cycles were measured through 3D mapping of the topography of the fretted surface. SEM and Fourier Transform Infrared Interferometry methods were used to examine the microspall pits and to measure the distribution of the thickness of oxide layer in the fretting region. For relatively small slip amplitude, the results showed that the fretting wear mechanism is initially dominated by adhesion and abrasion actions and then by delamination and surface fatigue. The time variation of the wear losses was shown to be cyclic until a steady state value is reached. At high slip amplitudes, however, abrasion and delamination are the only dominant wear mechanisms. The volumetric wear losses were found to decrease monotonically with the number of cycles. A novel approach was introduced, whereby the thermal and electrical contact resistances of the fretting interface are simultaneously measured. The results demonstrated the potential use of this non-intrusive approach for real-time monitoring of the fretting wear mechanism.     

On the mechanisms of various fretting wear modes

According to relative motion directions for a ball-on-flat contact, there are four fundamental fretting wear modes, e.g., tangential, radial, torsional and rotational modes. In this paper, the mechanisms of these four fundamental fretting wear modes, particularly for the later three modes, have been reviewed from results obtained by the authors in combination with results from literature. Some general features have been reported. Differences both in running and degradation behavior have been discussed in detail. Results showed that some similar laws for three fretting regimes (partial slip regime, mixed regime and slip regime), fretting maps (running condition fretting map and material response fretting map), wear and cracking mechanisms obtained from the classic mode (i.e. tangential fretting) were also identified and useful to characterize the other modes. Nevertheless, the occurrence of relative slip for the radial fretting, the formation of mixed regime for the torsional fretting, the evolution of surface morphology for the rotational fretting were quite different compared to that of the classical fretting mode.     

The investigation of the steady stage of steel fretting

The effects of slip length, frequency, surface pressure and shape of the longitudinal oscillatory motion on the fretting wear of steel were investigated by a specially designed fretting apparatus using an M.T.S. closed loop axial hydraulic testing system.

The rate of fretting wear in the steady stage was found to increase with increasing slip length and specific surface pressure and to decrease with increasing cyclic frequency and material hardness. The wave shape of the oscillatory motion does not appear to affect the wear rate.

Increased slip, greater surface pressure and lower cycling frequency all promote the adhesion mechanism of fretting. With higher frequencies decreased slip and low surface pressures, the product of fretting wear is mainly oxides and oxidation is the leading wear mechanism.     

基于双重扩展自适应卡尔曼滤波的汽车状态和参数估计

准确实时地获取行驶过程中的状态信息是汽车动态控制系统研究的关键,为此提出了一种新的汽车状态估计器。建立了包含不准确模型参数和未知时变统计特性噪声的非线性汽车动力学模型,针对该非线性系统提出一种双重扩展自适应卡尔曼滤波算法（DEAKF）。该算法采用两个卡尔曼滤波器并行运算,状态估计和参数估计互相更新,同时将带遗忘因子的噪声统计估值器嵌入到状态校正过程和参数校正过程之间,以解决系统的噪声时变问题。基于ADAMS的虚拟试验和实车试验结果表明,该算法的状态估计精度高于EKF方法和DEKF方法的状态估计精度,同时具有良好的模型参数校正能力,对汽车动态控制系统中估计器的设计具有理论指导意义。
     

AZ91D镁合金微动磨损特性研究

采用液压高精度材料试验机考察了平面一球面接触的AZ91D镁合金摩擦副的微动磨损行为，分析了位移幅值、法向载荷和频率等参数对摩擦因数和磨损体积的影响，考察了不同实验条件下的磨斑形貌，并探讨了其磨损机理。结果表明：AZ91D镁合金的微动区域可分为部分滑移区、混合区和滑移区3个区域，粘着磨损、疲劳磨损和磨粒磨损分别是3个区域的主要磨损机制；磨损体积随着位移幅值和法向载荷的增加而增大，但却随着频率的增大而减小。在微动部分滑移区和混合区，摩擦因数随着位移增大迅速增加；在微动滑移区，摩擦因数随法向载荷的增大而减小，而位移幅值和频率对摩擦因数的影响较小。     

TiAlZr合金微动磨损性能研究

采用高精度液压式微动磨损试验机研究了TiA lZr合金在不同微动运行区域的微动磨损行为,建立了其运行工况微动图。试验结果表明:滑移区、混合区和部分滑移区的摩擦因数随循环次数变化呈现不同的规律,其中部分滑移区摩擦因数较低,磨损体积随着位移幅值的增大而增大;滑移区、混合区磨损体积随着法向载荷的增加而增大,而部分滑移区磨损体积随着法向载荷的增加而减小;滑移区磨屑堆积于中心区域,磨损以磨粒磨损和剥层机制为主;混合区磨损机制主要表现为粘着磨损与磨粒磨损并存;部分滑移区磨损轻微。     

Differences in Mechanisms for Fretting Wear Reduction between Oil and Grease Lubrication

The different mechanisms of fretting wear in oil and grease lubrication and methods to reduce fretting wear were examined by means of thrust ball bearings in this study. Tests of fretting wear under oil lubrication were conducted. It was confirmed that high-viscosity oil can reduce fretting wear at high velocity (i.e., high frequency) through oil film formation. In the case of grease lubrication, the influence of velocity on fretting wear was significantly different for low- and high-viscosity greases. Grease with low-viscosity base oils could reduce fretting wear at high velocity. In contrast, grease with high-viscosity base oils could reduce fretting wear at low velocity. Grease thickeners were found to be effective in forming a layer that could prevent fretting wear. These results highlight the large differences in effective fretting wear reduction mechanisms between oil and grease lubrication.     

Effect of contact load on fretting fatigue behaviour of steel wires

Abstract

The tension–tension fretting fatigue tests of steel wires were performed on a self-made fretting fatigue test equipment under contact loads ranging from 40 to 70 N and a strain ratio of 0·8. The results showed that when the contact load increased, the fretting regime of steel wires transformed from gross slip regime to mixed fretting regime. The fretting fatigue life in the mixed fretting regime was significantly lower than that in the gross slip regime. The main fretting wear mechanisms in the gross slip regime, where there were serious fretting damage and a lot of wear debris, were abrasive wear and fatigue wear. Microcracks were observed in the fretting scar of the mixed fretting regime, and the main fretting wear mechanisms were adhesive and fatigue wears. The fretting wear scar was the fatigue source region, and the fatigue fracture surface could be divided into three regions.     

Fretting wear behaviors of a railway axle steel

Fretting damage was one of the most important reasons for the failure of the railway axle. Fretting wear (tangential fretting mode) tests of a railway axle steel (LZ50 steel) flats against 52 100 steel balls were carried out under different normal loads and displacement amplitudes on a hydraulic fretting wear rig. Dynamic analyses in combination with microscopic examinations have been performed. The experimental results showed that the fretting regimes of the LZ50 steel were strongly dependent upon the imposed normal loads and displacement amplitudes. The F_t/F_n curves exhibited different variation trends in different fretting running regimes. The fretting scars presented slight damage in partial slip regime. In mixed fretting regime, the trace of the plowing and plastic deformation flow can be observed on the fretting scars. The wear mechanism during this regime was the combination of the abrasive wear, oxidative wear and delamination accompanied with obvious plastic deformation. The detachment of particles and plowing traces were the main phenomena in slip regime. And, thicker debris layer covered the contact zone of the scar. The severe degradation in slip regime presented the main wear mechanisms of abrasive wear, oxidative wear and delamination.     

桨-毂轴承材料扭动微动磨损行为研究

采用面接触扭动微动形式,以动力定位系统可调距螺旋桨桨-毂轴承摩擦副材料(CuNiAl-42CrMo4)为对象,以不同的角位移幅值模拟海水波动影响下的微动磨损行为,并结合扫描电子显微镜和超景深三维显微镜对磨痕形貌进行分析,探究桨-毂轴承摩擦副材料扭动微动磨损规律。结果表明,随着角位移幅值的增加,扭动微动依次运行于部分滑移区、混合区、滑移区,摩擦因数减小,同时磨损量增加,微动损伤中剥层机制所占的比例逐渐增加,且由于疲劳裂纹扩展的不利影响,实际运行过程中要尽量避开混合区。     

A tentative explanation for the tribochemical effects in fretting wear

In many fretting investigations, tribochemical reactions have been reported to critically determine the wear and friction behavior, however, different and contradictory assessments of the importance of mechanical and thermal effects on these reactions have been suggested. Since fretting is characterized by relatively slow sliding speeds, high temperatures are not generated over the entire nominal contact area. However, evidence for phase transformations, which are typical of high temperatures, have been observed many times in fretting experiments. In other words, there exists a discrepancy between the macro- and micro-scale observations. In our previous experimental and theoretical work, the tribochemical transformations of steel and ceramics were extensively investigated and the presence of very high flash contact temperatures under gross slip fretting was confirmed. In this paper we present a tentative explanation of the mechanism for the observed tribochemical changes under selected fretting conditions, which can also explain the discrepancy in the results from macro- and micro-scale studies. The proposed wear mechanism considers the tribochemical transformations at the asperity spot-to-spot contacts due to high flash temperatures, while the heat generation and dissipation at apparent contact area remain significantly lower. The observed overall wear transition occurs due to gradual accumulation of the transformed material, which in “closed” fretting contacts remains in great part within the contact.     

The influence of oxygen and water vapour on the friction and wear of an aluminium alloy under fretting conditions

An investigation was conducted to determine the effect of oxygen and water vapour on the friction and wear behaviour of an Al-Zn-Mg alloy under fretting conditions. Fretting wear experiments were carried out in wet air, dry air and in dry argon. In this case the peak-to-peak relative slip amplitude was varied from 20 to 260 μm to determine the critical slip amplitude of fretting wear in these environments.The experimental results indicated that the wear rates in dry air and in dry argon under macroslip conditions were almost the same and quite lower than the wear rate in wet air. This revealed that the effect of oxygen on fretting wear was not large but that water vapour accelerated the fretting wear of the aluminium alloy. The cyclically softened material due to overaging was observed below the contact surface during fretting in wet air. The mechanism involved rapid fretting wear in wet air which caused the removal of a heavily work-hardened layer as it was formed but the softened material below it was not removed.     

Development of a test device for the evaluation of fretting in point contact

Fretting wear and fatigue may occur between any two contacting surfaces, wherever short‐amplitude reciprocating sliding is present for a large number of cycles. A test device has been developed for the evaluation of fretting fatigue and wear in partial and gross slip conditions. Three similar sphere‐on‐plane contacts run at the same time. Normal force, tangential force or displacement amplitude and constant bulk stress can be controlled and measured separately. Reciprocating tangential displacement is produced with rotational motion, the amplitude and frequency of which can be adjusted and controlled accurately by an electric shaker. The number of load cycles for crack initiation and growth is determined with strain‐gauge measurements near the fretting point of contact. The contact surfaces are measured with 3D optical profilometer before fretting measurements to determine actual contact geometry. The measurements were done with quenched and tempered steel. The initial results indicate that cracks are mostly formed in partial slip conditions, whereas fretting wear is more heavily involved in gross slip conditions. The initiation of a crack occurs near the edge of the contact in the slip direction, where the calculated cracking risk has its maximum value in partial slip conditions. The number of cracks increases as the displacement amplitude, i.e. friction force, increases in partial slip conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

The effect of slip amplitude on fretting

The effect of slip amplitude on the mechanism of fretting was investigated. Measurements of wear volume, frictional coefficient and of electrical contact resistance were carried out to clarify the wear mechanism. X-ray microdiffraction was used to observe the difference of wear behaviour, and scanning electron microscopic observations were made.At small slip amplitudes wear damage was small compared with that at larger amplitudes the transition being in the region of 70 μ.At smaller slip amplitudes fretting oxidation, a mild type of wear occurs. At larger slip amplitudes, adhesion and abrasion together with oxidation cause fretting wear. At much larger slip amplitudes, wear similar to reciprocating sliding wear occurs.     

中性腐蚀环境下钢丝的微动疲劳行为

在自制的微动疲劳试验机上开展中性腐蚀环境下单根钢丝的微动疲劳实验,考察在相同接触载荷下,不同振幅对钢丝的微动疲劳行为的影响,并用扫描电子显微镜观察疲劳钢丝的磨痕和断口形貌,研究钢丝微动疲劳断裂机制.结果表明:在较大的振幅下,钢丝的微动区均处于滑移状态,而在较小振幅下,钢丝的微动区从滑移状态逐渐转变为黏着状态;磨损机制主要为磨粒磨损、疲劳磨损、腐蚀磨损和塑性变形;钢丝疲劳寿命随着微动振幅的增大而减小;钢丝的疲劳断口可分为3个区域,即疲劳源区、裂纹扩展区及瞬间断裂区.     

Study on rotational fretting wear of 7075 aluminum alloy

Rotational fretting wear tests in a ball-on-flat configuration have been successfully realized on a special rotational fretting rig developed from an ultra-low-speed reciprocating rotational driver. The rotational fretting behavior of 7075 aluminum alloy against 52 100 steel was studied under different angular displacement amplitudes and normal loads. The results showed that both F_t?θ and F_t/F_n curves can be used to characterize the rotational fretting running behavior, which exhibited different curve shapes and variation trends in different fretting running regimes. The rotational fretting behavior of 7075 aluminum alloy was strongly dependent on the angular displacement amplitude, normal load and number of cycles. The wear of 7075 aluminum alloy was characterized by slight attrition in the partial slip regime, while a combination of delamination, abrasive and oxidative wear was found in the slip and mixed fretting regimes. The formation of a central bulge probably due to plastic flow was observed under gross slip condition of the rotational fretting mode.