The synthesis of (N1E,N4E)-N1,N4-bis(pyridine-2-YL) ethylene benzene-1,4-diamine and investigation of its efficiency as new binuclear catalyst complex in copper-based ATRP

(N¹E,N⁴E)-N¹,N⁴-bis(pyridin-2-yl) ethylene benzene-1,4-diamine (BPEBD) was synthesized by condensation of 2-acetyl pyridine and 1,4-diaminobenzene and its efficiency as a catalyst in Cu-based atom transfer radical polymerizations (ATRP) of methyl methacrylate (MMA) and styrene (S) was investigated. Linear first-order kinetic plots were obtained. However, there were induction periods. The apparent rate constant values of ATRP of MMA with CuCl/BPEBD catalyst system in toluene were found to be between 2.10 × 10^?5 and 9.83 × 10^?5 s^?1, while they were between 6.67 × 10^?6 and 3.30 × 10^?5 s^?1 in the case of acetonitrile, indicating the presence of a low radical concentration throughout the polymerizations. Low apparent rate constant values denote a good control over ATRP in general. Apparent rate constant vs [ligand]/[catalyst] ratio plots showed a maximum at the [ligand]/[catalyst] ratio of 1. In the ATRP of MMA in toluene, M _n,GPC values increased linearly with conversion and these molecular weight values were close to M _n,th in comparison to that of in acetonitrile. In the polymerization of S, the control of molecular weights was not good, although the reactions were first-order kinetics. Cyclic voltammetry measurements confirmed that CuCl/BPEBD complex in acetonitrile gives quasi-reversible redox couples, and copper (I) centers in CuCl/BPEBD binuclear catalyst complexes are readily oxidized and it potentially suits to facile ATRP.     

A study on polymer blend electrolyte based on PVA/PVP with proton salt

Proton-conducting polymer blend electrolytes based on PVA–PVP–NH₄NO₃ were prepared for different compositions by solution cast technique. The prepared films are investigated by different techniques. The XRD study reveals the amorphous nature of the polymer electrolyte. The FTIR and laser Raman studies confirm the complex formation between the polymer and salt. DSC measurements show decrease in T _g with increasing salt concentration. The ionic conductivity of the prepared polymer electrolyte was found by ac impedance spectroscopy analysis. The maximum ionic conductivity was found to be 1.41 × 10^?3 S cm^?1 at ambient temperature for the composition of 50PVA:50PVP:30 wt% NH₄NO₃ with low-activation energy 0.29 eV. The conductivity temperature plots are found to follow an Arrhenius nature. The dielectric behavior was analyzed using dielectric permittivity (ε*) and the relaxation frequency (τ) was calculated from the loss tangent spectra (tan δ). Using this maximum ionic conducting polymer blend electrolyte, the primary proton battery with configuration Zn + ZnSO₄·7H₂O/50PVA:50PVP:30 wt% NH₄NO₃/PbO₂ + V₂O₅ was fabricated and their discharge characteristics studied.     

Hydrogen peroxide sensor based on riboflavin immobilized at the nickel oxide nanoparticle-modified glassy carbon electrode

A simple and sensitive electrochemical sensor based on nickel oxide nanoparticles/riboflavin-modified glassy carbon (NiONPs/RF/GC) electrode was constructed and utilized to determine H₂O₂. By immersing the NiONPs/GC-modified electrode into riboflavin (RF) solution for a short period of time (5–300 s), a thin film of the proposed molecule was immobilized onto the electrode surface. The modified electrode showed stable and a well-defined redox couples at a wide pH range (2–10), with surface-confined characteristics. Experimental results revealed that RF was adsorbed on the surface of NiONPs, and in comparison with usual methods for the immobilization of RF, such as electropolymerization, the electrochemical reversibility and stability of this modified electrode has been improved. The surface coverage and heterogeneous electron transfer rate constants (k _s) of RF immobilized on a NiO _x –GC electrode were approximately 4.83 × 10^?11 mol cm^?2, 54 s^?1, respectively. The sensor exhibits a powerful electrocatalytic activity for the reduction of H₂O₂. The detection limit, sensitivity and catalytic rate constant (k _cat) of the modified electrode toward H₂O₂ were 85 nM, 24 nA μM^?1 and 7.3 (±0.2) × 10³ M^?1 s^?1, respectively, at linear concentration rang up to 3.0 mM. The reproducibility of the sensor was investigated in 10 μM H₂O₂ by amperometry, the value obtained being 2.5 % (n = 10). Furthermore, the fabricated H₂O₂ chemical sensor exhibited an excellent stability, remarkable catalytic activity and reproducibility.     

Dielectric and electrical characterization of (PEO–PMMA)–LiBF<Subscript>4</Subscript>–EC plasticized solid polymer electrolyte films

Plasticized solid polymer electrolytes (PSPEs) consisting of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50/50 wt%) based matrix with lithium tetrafluoroborate (LiBF₄) as dopant ionic salt (10 wt%) and varied concentrations (x = 0, 5, 10 and 15 wt%) of ethylene carbonate (EC) as plasticizer have been prepared. Classical solution-cast (SC) and the ultrasonic assisted followed by microwave irradiated (US–MW) solution-cast methods have been used for the preparation of (PEO–PMMA)–LiBF₄–x wt% EC films, and the same have been hot–pressed to get their smooth surfaces. Dielectric relaxation spectroscopy (DRS) and X–ray diffraction (XRD) techniques have been employed to characterize the dielectric and electrical dispersions and the structural properties of the PSPE films, respectively. It has been observed that the ionic conductivity of these semicrystalline ion-dipolar complexes is governed by their dielectric permittivity and polymers chain segmental dynamics. The increase in ionic conductivity values with the increase of plasticizer concentration in the PSPEs also varies with the films’ preparation methods. The US–MW method prepared PSPE film containing 15 wt% EC has a maximum ionic conductivity (1.86 × 10^?5 S cm^?1) at room temperature, whereas, the films having low concentrations of EC exhibit the conductivity of the order of 10^?6 S cm^?1.     

Studies on Interaction of Polysaccharide-Templated Silver Nanoparticles with Bovine Serum Albumin

In the present work, the interaction between bovine serum albumin (BSA) and as-synthesized silver nanoparticles (Oc-AgNPs) by using 4-acetamido-TEMPO-oxidized curdlan (Oc), as a reducing and stabilizing agent, was studied through fluorescence quenching method, ultraviolet visible spectrum (UV–Vis), and circular dichroism measurement. The results presented clearly indicate that the intrinsic fluorescence of BSA molecule was effectively quenched after the interaction with Oc-AgNPs by a static mechanism, which is further confirmed by UV–Vis analysis. The apparent binding constant (K), number of binding sites (n), and dissociation equilibrium constant (K_D) were calculated to be 7.5 × 10⁵ M^?1, 1.03, and 3.0 ± 0.6 μM, respectively. Furthermore, a conformational change of BSA was also observed when the Oc-AgNPs–BSA interactant formed.     

Synthesis,characterization of poly‐2‐ (2‐hydroxybenzylideneamino)‐6‐phenyl‐4,5,6, 7‐tetrahydrobenzo[b]thiophene‐3‐carbonitrile: Investigation of antibacterial activity and optical properties

The oxidative polycondensation reaction conditions of 2‐(2‐hydroxybenzylideneamino)‐6‐phenyl‐4,5,6,7‐tetrahydrobenzo[b]thiophene‐3‐carbonitrile were examined. The magnitude of the reflectance of the polymer decreases sharply with increasing of wavelength up to 524 nm, then reflectance of the polymer increases slowly with increasing of wavelength. The refractive index values of the polymer vary from 1.474 to 2.350. The E_p and E_d values of the polymer were found to be 4.56 and 7.068 eV, respectively. Absorption coefficient K of the polymer is of the order 817.062–1434.77 m^?1. Angle values of incidence and refraction of the polymer vary from 57.36 to 66.95° and from 23.05 to 32.65°, respectively. The film‐phase thickness of the polymer increases with increasing photon energy. The thickness, d, of the polymer was of the order 439.3–4184.7 Å for 190 and 1100 nm, respectively. The real part of dielectric constant of the polymer decreases slowly with increasing of frequency up to about 600 THz, then the real part of dielectric constant of the polymer increases sharply with increasing of frequency. The real and imaginary parts of dielectric constant of the polymer vary from 2.17 to 5.52 and from 5.81 × 10^?5 to 3.58 × 10^?4, respectively. Finally, polymer was tested for antibacterial activities against some bacteria. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Preparation and properties of KH550-Al2O3/PI–EP nanocomposite material

First, polyimide (PI)–epoxy resin (EP) polymer matrix was prepared from 3,3′-diethyl-4,4′-diamino diphenyl methane (DEDADPM), benzophenone tetracarboxylic acid dianhydride (BTDA) and epoxy resin (E-51), through thermal imide process. Then, the nanometer alumina (Al₂O₃) modified by the coupling agent, (3-aminopropyl)triethoxysilane (KH550), was doped into the PI–EP polymer matrix, using an in situ sol–gel method to prepare a series of KH550-Al₂O₃/PI–EP nanocomposite materials based on different KH550-Al₂O₃ contents. Fourier transform infrared spectroscopy (FTIR) indicated that in the presence of chemical reaction between poly(amic acid) and epoxy resin, an imide ring was formed, the thermal imidization reaction of the materials was completed and the KH550-Al₂O₃ had doped into the PI–EP polymer matrix. The heat-resistance, dielectric specification and mechanical properties of KH550-Al₂O₃/PI–EP nanocomposite materials were evaluated. The results showed that the decomposition temperatures were ranged between 438 and 450 °C, dielectric constant and dielectric loss were in the range of 3.32–3.71 and 1.5 × 10^?3–2.5 × 10^?2, respectively, and they all increased with the increase of KH550-Al₂O₃ content (0–10 wt%), but the shear strength first increased and then decreased, attained its maximum value of 10.64 MPa at 8 wt%, which was about 119 % higher than that of undoped material. The adhesive forces of nanocomposite materials were all at higher level (one or two levels). Thus, the overall performance of KH550-Al₂O₃/PI–EP nanocomposites was the best when the doping amount of KH550-Al₂O₃ was 8 wt%. The properties such as high heat-resistance, dielectric properties and ready attachment of impregnating varnish to steel plate with very high strength fully met the necessary requirement.     

Anionic polymerization of styrene in triglyme-benzene mixtures

Living anionic polymerization of styrene was kinetically investigated in triglyme-benzene mixtures. At low concentrations of triglyme the overall propagation rate constant, k_p, was much larger than at the same concentration of monoglyme (DME) in DME-benzene mixtures. The Szwarc-Schulz plot did not have negative slopes for lithium and sodium salts at triglyme contents of 5～20vol%, and no contribution of free anions to the propagation was observed for the sodium salt. The sodium ion pair was more highly reactive than the lithium ion pair; thus at 25°C, the ion pair rate constant, k′_p, for the lithium salt was 43, 102, 135 and 165 M^?1sec^?1 at triglyme concentrations of 5, 10, 15, and 20%, respectively, while that for the sodium salt was 410, 920, and 1460 M^?1sec^?1 in 5, 10, and 15% triglyme, respectively. The dissociation constant, K, for the lithium salt was 2·4×10^?11, 1·9×10^?10 and 1·3×10^?9 M in 10, 15, and 20% triglyme, respectively and the free ion rate constant, k″_p, was 2～2·5×10⁴ M^?1sec^?1 for the lithium salt.     

2,6-Bis-benzimidazolylpyridines as new catalyst in copper-based ATRP

The ligands, 2,6-bis(NH-benzimidazol-2-yl)pyridine (L1) and 2,6-bis(N-methyl-benzimidazol-2-yl)pyridine (L2), were synthesized by a one-step reaction of 2,6-pyridinedicarboxylic acid with a diamine (o-phenylenediamine or N-methyl-1,2-phenylenediamine), respectively, in syrupy phosphoric acid at ca. 200 °C. Their efficiency as a catalyst in Cu-based atom transfer radical polymerizations (ATRP) of methylmethacrylate (MMA) was investigated. The linear first-order kinetic plots were observed; indicating that the number of active species is constant during the polymerization and termination reactions are limited. The apparent rate constant values of ATRP of MMA with CuCl/L1 catalyst system at 90 °C in acetonitrile were found to be between 3.83 × 10^?5 and 1.33 × 10^?4 s^?1, while they were between 1.86 × 10^?4 and 4.40 × 10^?4 s^?1 in the case of CuCl/L2 catalyst, indicating the presence of lower radical concentration throughout the polymerization of MMA using CuCl/L1 catalyst system. In both the cases, low apparent rate constant values are obtained. This indicates that ATRP proceeded at reasonable rates and a good control over ATRP in general. Apparent rate constant vs [ligand]/[catalyst] ratio plots showed a maximum at the [ligand]/[catalyst] ratio of two. M _n,GPC values increased slightly linearly with conversion and molecular weight values were closer to M _n,th in the case of ATRP of MMA using CuCl/L2 catalyst complex. Cyclic voltammetry measurements confirmed that CuCl/L1 and CuCl/L2 complexes in acetonitrile give reversible redox couples and copper(I) centers in CuCl/L1 and CuCl/L2 catalyst complexes that are readily oxidized and they potentially suit to facile ATRP.     

A.C. Conductivity and Dielectric Properties of Polycarbonate Sheet

ABSTRACT

The a.c. conductivity σ_a.c(ω), the dielectric constant ?′ and dielectric loss ?″ of polycarbonate sheet have been studied in the frequency range 1.5 × 10²–5 × 10⁶ Hz and temperature range 294–473 K. A.c. conductivity σ_a.c(ω) results show that it depends strongly on the frequency and slightly on the temperature, with activation energy between 0.0003 and 0.085 e.V. The a.c. conductivity σ_a.c(ω) as a function of frequency is well described by a power law Aω^S where S is the frequency exponent. The obtained values of S < 1 in the first region over the frequency range 1.5 × 10²–4 × 10³ Hz, the temperature dependence of both a.c. conductivity σ_a.c(ω) and the parameter S are reasonably well interpreted by the correlated barrier hopping (CBH) model. The second region, where S > 1 over the frequency range 4 × 10³–5 × 10⁶ Hz, has a strong dependence on the frequency but near independence of the temperature, suggesting that the conductivity may be interpreted by the Maxwell–Wagner (M–W) dispersion. In the first region, the optical band gap of the material, E_g, and the maximum barrier height, W_m, are calculated, suggesting that there is agreement with that proposed by the theory of hopping of charge carriers over potential barrier as suggested. Spatial inhomogeneity may affect the conduction mechanisms in polycarbonate. The experimental values of dielectric constant, ?′ and dielectric loss, ?″, show their dependence on temperature and frequency.     

Electrical Properties of Triethylene Glycol Stabilized MnxCo1-xFe2O4 Nanoparticles

We reported on the synthesis and analysis of the composition, micro-structure, ac–dc conductivity performance and dielectric permittivity of triethylene glycol (TEG) stabilized Mn_xCo_1-xFe₂O₄ nanoparticles obtained by polyol method. Crystallite size from XRD and particle size from TEM micrographs are consistent with each other. Conductivity measurements were performed to investigate the influence of the coating with TEG on the conduction characteristics of Mn_xCo_1-xFe₂O₄ NP’s. The frequency-dependency of the ac conductivity shows electrode polarization effect. The dc conductivity is strongly temperature dependent and shows maximum conductivity of about 5 × 10^?5 S cm^?1 for x = 1.0 at 120 °C. Analysis of dielectric permittivity functions suggests that ionic and polymer segmental motions are strongly coupled.     

Synthesis and characterization of some new aromatic polytriazoles as proton conductive membranes

A series of new poly(1,2,4-triazole)s (PTAs) containing pyridine heterocyclic ring, bearing bulky aromatic pendent groups, were synthesized from the reaction of the corresponding polyhydrazides with aniline or 4-aminobenzenesulfonic acid in polyphosphoric acid (PPA) at 175 °C. The non-sulfonated PTAs showed glass transition temperatures (T _gs) of 220–250 °C and inherent viscosities (η _inh) equal to 0.48–0.78 dL/g, and the sulfonated poly(1,2,4-triazole)s (S-PTAs) exhibited T _gs of 235–265 °C and inherent viscosities equal to 0.50–0.83 dL/g. The former polymers were soluble in conc. H₂SO₄ and partially soluble in hot N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), dimethylacetamide (DMAc), and 1-methyl-2-pyrrolidone (NMP), and the latter were soluble in DMF, NMP, DMSO and DMAc at room temperature. All polymers had useful levels of thermal stability and were stable up to 450 °C in nitrogen. The proton conductivities of undoped sulfonated polytriazole membranes and the acid-doped sulfonated polytriazole membranes lie in the range of 5 × 10^?4–8.1 × 10^?3 and 5 × 10^?3–2.3 × 10^?2 S/cm, respectively, at 90 °C and 100 % relative humidity.     

Synthesis and characterization of gallic acid derivatives and their utilized as organic photo-stabilizers for poly (vinyl chloride)

The photo-stabilization of poly (vinyl chloride) containing 1,3,4-thiadiazole derivatives derived from Gallic acid as additives were studied. The four different substituents of 1,3,4-thiadiazole-gallic derivatives, 2-(4-substituted-phenyl)-5-(3,4,5-trimethoxyphenyl)-1,3,4-thiadiazole, (R1-R4) were prepared starting from Gallic acid and characterized by FTIR, ¹HNMR and elemental analysis. The 5% concentration by weight of these derivatives (R1-R4) in PVC polymer was used to study the photo-stabilization of PVC. The photo-stabilization of PVC films were studied at room temperature under irradiation of U.V light with λ = 385 nm and an intensity of 7.75 × 10^?7 Einstein dm^?3 s^?1. The photo-stabilization activity of these compounds was determined by monitoring the carbonyl (I_CO), polyene (I_po) and hydroxyl (I_OH) indices and weight loss method with irradiation time. It was found that the (I_CO), (I_po) and (I_OH) index values increased with the irradiation time increase, this increase found to depend on the type of additives, also it was found that the PVC films in the presence of additives (R1-R4) were arranged as the following trend: PVC + R1 > PVC + R2 > PVC + R3 > PVC + R4.     

Sensitive molecular determination of polycyclic aromatic hydrocarbons based on thiolated Calix[4]arene and CdSe quantum dots (QDs)

A novel and sensitive electrochemical sensor based on the cone conformation of the supramolecule 25, 27-(3-thiopropoxy)-p-tert-butyl calix[4]arene has been developed for quantitative determination of polycyclic aromatic hydrocarbons (PAHs). The method works effectively by immobilizing calix[4]arenes on Fe₃O₄ magnetic nanoparticles. CdSe quantum dots were used as electrochemical labels. CdSe quantum dots (QDs) modified PAHs in competition with the sample PAHs were intercalated into calix[4]arenes supramolecules via a host–guest interaction through individual bowl-shaped calix[4]arenes. The stripping analysis of the cadmium dissolved from CdSe nanoparticles provided a sensitive method for the detection of PAHs in the samples. The signal decrease of the QDs was proportional to the increase in the concentration of the PAHs. Under optimal conditions, among the five PAHs, the square wave voltammetry (SWV) response of QDs decreased linearly for anthracene and naphthalene in the range of 2.1 × 10^?7–1.4 × 10^?5 and 1.5 × 10^?6–2.5 × 10^?5 M, respectively. The calculated detection limits (3δ) were 20.1 ng mL^?1 for anthracene and 105.5 ng mL^?1 for naphthalene.     

Graft copolymerization onto starch. II. Grafting of acrylonitrile to granular native potato starch by manganic pyrophosphate initiation. Effect of reaction conditions on grafting parameters

The effect of reaction conditions on the composition of native potato starch–polyacrylonitrile graft copolymers initiated by manganic pyrophosphate onto starch slurries at 30°C has been examined. In general, when the Mn³⁺ ion concentration was increased from 0.15 × 10^?3M to 3.0 × 10^?3M (other conditions kept constant), an increase in conversion of monomer to polymer and % add-on was observed, whereas frequency of grafts (anhydroglucose units, AGU, per grafted chain) decreased. Also, the average molecular weights of grafts showed a decrease from 2.2 × 10⁵ to 1.5 × 10⁵. Increasing the concentration ratio of starch to monomer during polymerization by a factor of 3 produced an increase in the conversion of monomer to polymer, whereas an increase in frequency of grafts (AGU/chain) was obtained. Values of % add-on and average molecular weights of the grafts showed, however, a decreasing tendency. It was observed that grafting onto starch took place readily even at acid additions as low as 10 × 10^?3M H₂SO₄ (pH ?1.8). Selective solvent extraction of homopolymer and extremely low conversions of monomer to polymer (0.1%–1.5%) in duplicate runs without addition of starch indicated that grafting efficiencies were high in all cases. An attempt has been made to interpret the results in terms of variations in factors such as initial ratio of (Mn³⁺)/(AGU), termination rate of acrylonitrile chain radicals by oxidation by Mn³⁺ ions, oxidation rate of radicals formed on anhydroglucose units by Mn³⁺ ions, and physical factors such as diffusion rate of Mn³⁺ ions through the polyacrylonitrile-grafted starch granules for terminating the radicals.     

A Strategy for Preparing Star Polymers Containing Metal–Metal Bonds Along the Polymeric Arms Using Click Chemistry

The [(η⁵-C₅H₄(CH₂)₃N₃)Mo(CO)₃]₂ dimer (3) was prepared and used to determine if the Huisgen cycloaddition reaction could be used to synthesize high molecular weight star polymers with metal–metal bonds in the arms. Several different click catalysts were examined. Cp*Ru(PPh₃)₂Cl (Cp* = η⁵-C₅(CH₃)₅) was previously shown to catalyze the formation of metal–metal bond-containing polymers using click chemistry; however, this catalyst underwent a Staudinger reaction with dimer 3 when a model coupling reaction was attempted with phenylacetylene. In order to avoid the Staudinger reaction, Cp*Ru(COD)Cl was used as the catalyst in the reaction of 3 with phenylacetylene, and coupling was observed after 14 h. Synthesis of a star polymer was attempted with 3 and 1,3,5-triethynylbenzene. Instead of coupling, Cp*Ru(COD)Cl reacted with the 1,3,5-triethynylbenzene. A third catalyst, Cu(IMes)Cl (IMes = 1,3-dimesityl-imidazol-2-ylidene) was used to couple 3 with 1,3,5-triethynylbenzene in 48 h. Both a high molecular weight polymer (M _n  = 77,000 g mol^?1) and a tripodal star core (M _n  = 1,800 g mol^?1) were successfully prepared with this catalyst.     

Electrochemical determination of malachite green at graphene quantum dots–gold nanoparticles multilayers–modified glassy carbon electrode

A graphene quantum dots–gold nanoparticles–modified glassy carbon electrode was used to investigate the electrochemical behaviors of malachite green (MG). Cyclic voltammetry curves of MG at the modified electrode exhibited a pair of quasi-reversible adsorption-controlled redox peaks at 0.502 V (E _pa) and 0.446 V (E _pc) in a 0.05 mol L^?1 H₂SO₄ solution. Under the optimal conditions, by using differential pulse voltammetry as the detection method, a linear relationship was obtained between the oxidation peak current and the MG concentration in the range of 4.0 × 10^?7 to 1.0 × 10^?5 mol L^?1 with the detection limit as 1.0 × 10^?7 mol L^?1 (signal-to-noise ratio of 3). The modified electrode was applied in the determination of MG in fish samples, and the results were satisfactory with recoveries from 96.25 to 98.00 %. Furthermore, the modified electrode showed very good reproducibility and stability.     

Effect of Metal-Support Interactions in Ni/ZSM-5 + Al2O3 Catalysts on the Transformation of n-Paraffins

NiO(8 %)/Ni,H-ZSM-5 + Al₂O₃ (1:1) catalysts differing in metal-support interactions, which influenced the metal-to-acid ratios, were examined. The interactions were changed by modifying the method of zeolite and aluminium hydroxide combining and the method of Ni incorporation. The catalysts were characterised by ICP, XRD, N₂ sorption, SEM, TEM, NH₃-TPD, Py-IR, TPR, H₂ chemisorption and XPS. The effect of metal-support interactions was determined during n-C₆ conversion in a continuous system at H₂:CH = 7:1 Nm³/m³, 0.1 MPa and LHSV = 1 h^?1. It was found that over the catalysts with weaker Ni–alumina interactions (n _{Ni_a}/n, 3.2 × 10^?2 and 4.8 × 10^?2), selectivity to isomerisation products was by 10–35 % higher, and selectivity to high boiling hydrocarbons by 10–30 % lower than over the catalysts with stronger Ni-support interactions (n _{Ni_a}/n, 1.2 × 10^?2 and 1.8 × 10^?2).     

Dielectric Properties of Sol–Gel‐Derived Bi12SiO20 Thin Films

In this paper the dielectric properties of crack‐free, Bi₁₂SiO₂₀ thin films were investigated. The films were prepared on Pt/TiO₂/SiO₂/Si and corundum substrates using the sol–gel method. The formation of a pure Bi₁₂SiO₂₀ phase was observed at a temperature of 700°C. The Bi₁₂SiO₂₀ thin films, heat treated at 700°C for 1 h, had a dense microstructure with an average roughness (R_a) of 50 nm. The dielectric properties of the film were characterized by using both low‐ and microwave‐frequency measurement techniques. The low‐frequency measurements were conducted with a parallel capacitor configuration. The dielectric constant and dielectric losses were 44 and 7.5 × 10^?3, respectively. The thin‐film dielectric properties at the microwave frequency were measured using the split‐post, dielectric resonator method (15 GHz) and the planar capacitor configuration (1–5 GHz). The dielectric constant and the dielectric losses measured at 15 GHz were 40 and 17 × 10^?3, respectively, while the dielectric constant and the dielectric losses measured with the planar capacitor configuration were 39 and 65 × 10^?3, respectively.     

Synthesis and two-photon absorption properties of 2,5-bis[4-(2-arylvinyl)phenyl]-1,3,4-oxadiazoles

Two symmetrical 2,5-bis[4-(2-arylvinyl)phenyl]-1,3,4-oxadiazoles that exhibit strong two-photon absorption and enhanced two-photon excited fluorescence were designed and synthesized based on “push-core-pull-core-push” molecules built from embedding electron-transporting 1,3,4-oxadiazole in aromatic conjugated system through Wittig–Horner reaction. Pumped by nanosecond laser at 800 nm, strong up-conversion emissions with the central wavelength at 507 nm (green) of 2,5-bis[4-(2-N,N-diphenylaminostyryl)phenyl]-1,3,4-oxadiazole and 475 nm (blue) of 2,5-bis[4-{2-(3-N-ethylcarbazolyl)vinyl}phenyl]-1,3,4-oxadiazole in the solution of CHCl₃ have been observed. Their two-photon absorption cross-sections obtained by nonlinear transmission method are 107 × 10⁻⁴⁸ cm⁴ s photon⁻¹ and 66 × 10⁻⁴⁸ cm⁴ s photon⁻¹. A very effective energy transfer from the excited terminal units to the π-conjugated bridging units of the 2,5-bis[4-(2-arylvinyl)phenyl]-1,3,4-oxadiazoles is the dominant contribution to the two-photon absorption.