Determination of the pore size distribution of micro porous layer in PEMFC using pore forming agents under various drying conditions

In this paper, the effect of the pore size distribution of a micro-porous layer (MPL) on the performance of polymer electrolyte membrane fuel cells (PEMFC) was investigated using self-made gas diffusion layers (GDLs) with different MPLs for which the pore size distribution was modified using pore forming agents under different drying conditions. When MPL dried at high temperature, more macro pores, approximately 1,000–20,000 nm in diameter, and less micro pores, below 100 nm, were observed relative to when MPL was dried at low temperature. Self-made GDLs were characterized by a field-emission scanning electron microscope (FE-SEM), mercury porosimetry and self-made gas permeability measurement equipment. The performance of the single cells was measured under two different humidification conditions. The results demonstrate that the optimum pore size distribution of MPL depended on the cell operating humidification condition. The MPL dried at high temperature performed better than the MPL dried at low temperature under a low humidification condition; however, MPL dried at low temperature performed better under a high humidification condition.     

Preparation of microporous layer for proton exchange membrane fuel cell by using polyvinylpyrrolidone aqueous solution

A new method of preparing microporous layer (MPL) for proton exchange membrane fuel cell (PEMFC) was presented in this paper. Considering the bad dispersion of PTFE aqueous suspension in the carbon slurry based on ethanol, polyvinylpyrrolidone (PVP) aqueous solution was used to prepare carbon slurry for microporous layer. The prepared gas diffusion layers (GDLs) were characterized by scanning electron microscopy, contact angle system and pore size distribution analyzer. It was found that the GDL prepared with PVP aqueous solution had higher gas permeability, as well as more homogeneous hydrophobicity. Moreover, the prepared GDLs were used in the cathode of fuel cell and evaluated with fuel cell performance and EIS analysis, and the GDL prepared with PVP aqueous solution indicated better fuel cell performance and lower ohmic resistance and mass transfer resistance.     

Effects of the carbon black properties in gas diffusion layer on the performance of proton exchange membrane fuel cells

The microporous layer (MPL) as a part of diffusion medium has an important impact on mass transfer of proton exchange membrane fuel cell (PEMFC). In this study, MPLs of gas diffusion layers (GDLs) are prepared with different carbon blacks, and the properties of carbon blacks and their effects as MPLs on cell performance are systematically investigated. The results show that the GDL prepared by Acetylene Black (ACET) exhibits the best performance with a maximum power density up to 2.05 W cm⁻². Moreover, it still maintains extremely high performance with increasing current density even at humidity condition of 100% relative humidity, which means its excellent water/gas transportation capacity. This study contributes to deeply understanding the correlations between the properties of MPL material itself and their corresponding performance exhibited in cell. It also provides an important reference for enhancing cell performance and further advancing the practical applications of MPLs in PEMFC field.     

Interfacial transport characteristics between heterogeneous porous composite media for effective mass transfer in fuel cells

In this study, a comprehensive computational model based on a full statistical approach was developed to investigate the heterogeneous mass transport properties in the metal foam channels, gas diffusion layers (GDLs), and microporous layers (MPLs) of polymer electrolyte fuel cells (PEFCs) at the 95% confidence level. A series of channels, GDLs, and MPLs were, respectively, generated to reflect the random heterogeneous structures and transport characteristics. The critical hydrophobic pore radius in the mixed wettability GDLs was computed by applying a modified Leverett function. Furthermore, the gas transport phenomenon through a sufficient number of porous transport media was simulated using a D3Q19 (ie, three‐dimensional, 19 velocities) lattice Boltzmann method, and the corresponding mass transport characteristics were mathematically presented as a function of the porosity. The permeabilities in the channels, GDLs, and MPLs were derived from the pressure gradient and the simulated velocity distribution. It was found that the effective mass diffusion coefficient in the GDLs is mainly influenced by molecular diffusion. Nevertheless, Knudsen diffusion is the dominant mass transfer mechanism in the MPLs, because of small pore diameters. In addition, critical hydrophobic pore radius was derived using a modified Leverett function, which enables to estimate the fraction of pores larger than the critical pore radius in GDLs for effective water transport. Moreover, the interfacial areal contact ratio between two adjacent porous media (ie, channel/GDL and GDL/MPL) was calculated. The calculations indicated that the variation in the local porosity of the porous media has a significant influence on the interfacial connections. The proposed model is expected to improve the prediction performance of porous heterogeneous transport media in electrochemical energy systems and the optimization of porous media structures.     

Reticulated polyaniline nanowires as a cathode microporous layer for high-temperature PEMFCs

Traditional dense microporous layers (MPLs) are suitable for low-temperature proton exchange membrane fuel cells (PEMFCs), but they greatly hinder mass transport in high-temperature PEMFCs. Here, we report a novel cathode MPL based on reticulated polyaniline nanowires that were grown on carbon paper via in-situ electropolymerization. The maximum power density of the high-temperature PEMFC based on the new MPL was 476 mW/cm², which was 36% higher than that based on a conventional MPL. Oxygen gain tests and electrochemical impedance spectroscopy showed that the new MPL accelerated oxygen transfer due to its unique pore size distribution, which ultimately improved the performance of the HT-PEMFC.     

Pore network modeling of fibrous gas diffusion layers for polymer electrolyte membrane fuel cells

A pore network model of the gas diffusion layer (GDL) in a polymer electrolyte membrane fuel cell is developed and validated. The model idealizes the GDL as a regular cubic network of pore bodies and pore throats following respective size distributions. Geometric parameters of the pore network model are calibrated with respect to porosimetry and gas permeability measurements for two common GDL materials and the model is subsequently used to compute the pore-scale distribution of water and gas under drainage conditions using an invasion percolation algorithm. From this information, the relative permeability of water and gas and the effective gas diffusivity are computed as functions of water saturation using resistor-network theory. Comparison of the model predictions with those obtained from constitutive relationships commonly used in current PEMFC models indicates that the latter may significantly overestimate the gas phase transport properties. Alternative relationships are suggested that better match the pore network model results. The pore network model is also used to calculate the limiting current in a PEMFC under operating conditions for which transport through the GDL dominates mass transfer resistance. The results suggest that a dry GDL does not limit the performance of a PEMFC, but it may become a significant source of concentration polarization as the GDL becomes increasingly saturated with water.     

Effect of the porous carbon layer in the cathode gas diffusion media on direct methanol fuel cell performances

The effect of cathode gas diffusion media with microporous layers (MPLs) on direct methanol fuel cell (DMFC) performances is studied by combining electrochemical analysis and physicochemical investigation. The membrane electrode assemblies (MEAs) using MPL-modified cathode gas diffusion layers (GDLs, GDL-1) showed slightly better performances (117 mW cm⁻²) at 0.4 V and 70 °C than commercial GDL (SIGRACET^® product version: GDL-35BC, SGL Co.) DMFC MEAs (110 mW cm⁻²). This might be due to high gas permeability, uniform pore distributions, and low water transport coefficient including methanol crossover. For GDL-1, the air permeability was 31.0 cm³ cm⁻² s⁻¹, while the one for SGL 35BC GDLs was 21.7 cm³ cm⁻² s⁻¹. Also, the GDL-1 in the pore-size distribution diagrams had distinct peaks due to more uniform distributions of macropores and micropores with smaller holes between aggregates of carbon particles compared to GDL-35 BC as confirmed by SEM images. Furthermore, the MEA using GDL-1 for the cathode had a lower water transfer coefficient compared to an MEA with a commercial 35 BC GDL.     

A pore network study on water distribution in bi-layer gas diffusion media: Effects of inlet boundary condition and micro-porous layer properties

Water flooding in gas diffusion material (GDM) is an important limit in performance of proton exchange membrane fuel cell (PEFMC). Some efforts, such as modifying the pore structures in the GDM, have been made in order to facilitate water transport and to reduce flooding in PEMFC. Recent experimental studies have demonstrated that using a bi-layer GDM, consisting of a fine micro-porous layer (MPL) and a coarse gas diffusion layer (GDL), can be advantageous for water management in PEMFC. In this work, a pore network model with an invasion percolation algorithm is developed and used to investigate the effects of MPL properties, including thickness, wettability and connectivity, on water distribution in the bi-layer GDM from the viewpoint at the pore level. Furthermore, a reasonable inlet boundary condition is proposed to describe the actual phenomenon that the CL surface is covered with many independent water droplets which are much larger than pore sizes in MPL. Influences of water droplet size and coverage fraction are also clarified in the present study.     

Gas diffusion layer for proton exchange membrane fuel cells—A review

Gas diffusion layer (GDL) is one of the critical components acting both as the functional as well as the support structure for membrane-electrode assembly in the proton exchange membrane fuel cell (PEMFC). The role of the GDL is very significant in the H₂/air PEM fuel cell to make it commercially viable. A bibliometric analysis of the publications on the GDLs since 1992 shows a total of 400+ publications (>140 papers in the Journal of Power Sources alone) and reveals an exponential growth due to reasons that PEMFC promises a lot of potential as the future energy source for varied applications and hence its vital component GDL requires due innovative analysis and research. This paper is an attempt to pool together the published work on the GDLs and also to review the essential properties of the GDLs, the method of achieving each one of them, their characterization and the current status and future directions. The optimization of the functional properties of the GDLs is possible only by understanding the role of its key parameters such as structure, porosity, hydrophobicity, hydrophilicity, gas permeability, transport properties, water management and the surface morphology. This paper discusses them in detail to provide an insight into the structural parts that make the GDLs and also the processes that occur in the GDLs under service conditions and the characteristic properties. The required balance in the properties of the GDLs to facilitate the counter current flow of the gas and water is highlighted through its characteristics.     

The influence of anode gas diffusion layer on the performance of low-temperature DMFC

The influence of the anode gas diffusion layers (GDLs) on the performances of low-temperature DMFCs, and the properties of mass transport and CO₂ removal on these anode GDLs were investigated. The membrane electrode assembly (MEA) based on the hydrophilic anode GDL, which consisted of the untreated carbon paper and hydrophilic anode micro-porous layer (comprised carbon black and 10 wt.% Nafion), showed the highest power density of 13.4 mW cm⁻² at 30 °C and ambient pressure. The performances of the MEAs tended to decline with the increase of the PTFE content in the anode GDLs due to the difficulty of methanol transport. The contact angle measurements revealed that the wettabilities of the anode GDLs decreased as the increase of PTFE content. The wettabilities of the GDLs were improved by addition of hydrophilic Nafion ionomer to the GDLs. From the visualizations of CO₂ gas bubbles dynamics on the anodes using a transparent cell, it was observed that uniform CO₂ gas bubbles with smaller size formed on hydrophilic anode GDLs. And bubbles with larger size were not uniform over the hydrophobic anode GDLs. It was believed that adding PTFE to the anode GDL was not helpful for improving the CO₂ gas transport in the anode GDL of the low-temperature DMFC.     

Through-plane gas permeability of gas diffusion layers and microporous layer: Effects of carbon loading and sintering

Knowledge of the absolute permeability for the various porous layers is necessary to obtain accurate profiles for water saturation within the membrane electrode assembly (MEA) in a two-phase model of a polymer electrolyte membrane fuel cell (PEMFC). In this paper, the gas permeability of gas diffusion layers (GDLs) coated with microporous layers (MPLs) of various carbon loadings for two different carbon blacks have been experimentally measured. The permeability of the GDL was found to decrease by at least one order of magnitude after the MPL-coating. Also, the permeability of the MPLs was shown to be lower than that of the carbon substrate by 2–3 orders of magnitude. Further, it was found that the gas permeability of the MPLs changes significantly from one carbon loading to another despite the use of a single weight composition for all the MPLs coated, namely 20% PTFE and 80% carbon black. This signifies the possible inaccuracy in estimating the MPL permeability through employing the cross-section SEM images as they do not resolve the MPL penetration into the carbon substrate. Finally, the MPL sintering was found to slightly decrease the permeability of the GDL.     

Numerical modeling and experimental study of the influence of GDL properties on performance in a PEMFC

This work is to study the effect of properties of gas diffusion layer (GDL) on performance in a polymer electrolyte membrane fuel cell (PEMFC) by both numerical simulation and experiments. The 1-dimension numerical simulation using the mixture-phase model is developed to calculate polarization curve. We are able to estimate optimum GDL properties for cell performance from numerical simulation results. Various GDLs which have different properties are prepared to verify accuracy of the simulation results. The contact angle and gas permeability of GDLs are controlled by polytetrafluoroethylene (PTFE) content in micro-porous layers (MPLs). MPL slurry is prepared by homogeneous blending of carbon powder, PTFE suspension, isopropyl alcohol and glycerol. Then the slurry is coated on gas diffusion mediums (GDMs) surface with controlled thickness by blade coating method. Non-woven carbon papers which have different thicknesses of 200 μm and 380 μm are used as GDMs. The prepared GDLs are measured by surface morphology, contact angle, gas permeability and through-plane electrical resistance. Moreover, the GDLs are tested in a 25 cm² single cell at 70 °C in humidified H₂/air condition. The contact angle of GDL increases with increasing PTFE content in MPL. However, the gas permeability and through-plane electrical conductivity decrease with increasing PTFE content and thickness of GDM. These changes in properties of GDL greatly influence the cell performance. As a result, the best performance is obtained by GDL consists of 200 μm thick non-woven carbon paper as GDM and MPL contained 20 wt.% PTFE content.     

Effect of fiber orientation on Liquid–Gas flow in the gas diffusion layer of a polymer electrolyte membrane fuel cell

In this study, the lattice Boltzmann method was used to simulate the three-dimensional intrusion process of liquid water in the gas diffusion layer (GDL) of a polymer electrolyte membrane fuel cell (PEMFC). The GDL was reconstructed by the stochastic method and used to investigate fiber orientation's influence on liquid water transport in the GDL of a PEMFC. The fiber orientation can be described by the angle between a single fiber and the in-plane direction; three different samples were simulated for three different fiber orientation ranges. The simulated permeability correlated well with the anisotropic characteristics of reconstructed carbon papers. It was concluded that the fiber orientation had a significant effect on the liquid invasion pattern in the GDL by changing the pore shape and distribution of the GDL. The results indicated that the stochastically reconstructed GDL, taking into account the fiber orientation, better demonstrates the mass transport properties of the GDL.     

A pore network study on the role of micro-porous layer in control of liquid water distribution in gas diffusion layer

In proton exchange membrane fuel cell (PEMFC), a hydrophobic micro-porous layer (MPL) is usually placed between catalyst layer (CL) and gas diffusion layer (GDL) to reduce flooding. Recent experimental studies have demonstrated that liquid water saturation in GDL is drastically decreased in the presence of MPL. However, theoretical studies based on traditional continuum two-phase flow models suggest that MPL has no effect on liquid water distribution in GDL. In the present study, a pore network model with invasion percolation algorithm is developed and used to investigate the impacts of the presence of MPL on liquid water distribution in GDL from the viewpoint at the pore level. A uniform pressure and uniform flux boundary conditions are considered for liquid water entering the porous layer in PEMFC. The simulation results reveal that liquid water saturation in GDL is reduced in the presence of MPL, but the reduction depends on the condition of liquid water entering the porous layer in PEMFC.     

Enhancement of proton exchange membrane fuel cell performance by titanium-coated anode gas diffusion layer

Titanium was coated onto an anode gas diffusion layer (GDL) by direct current sputtering to improve the performance and durability of a proton exchange membrane fuel cell (PEMFC). Scanning electron microscopy (SEM) images showed that the GDLs were thoroughly coated with titanium, which showed angular protrusion. Single-cell performance of the PEMFCs with titanium-coated GDLs as anodes was investigated at operating temperatures of 25 °C, 45 °C, and 65 °C. Cell performances of all membrane electrode assemblies (MEAs) with titanium-coated GDLs were superior to that of the MEA without titanium coating. The MEA with titanium-coated GDL, with 10 min sputtering time, demonstrated the best performance at 25 °C, 45 °C, and 65 °C with corresponding power densities 58.26%, 32.10%, and 37.45% higher than that of MEA without titanium coating.     

Evaluating breakthrough pressure in gas diffusion layers of proton exchange membrane fuel cells

This paper studied the breakthrough pressure for liquid water to penetrate the gas diffusion layer （GDL） of a pro- ton exchange membrane fuel cell （PEMFC）. An ex-situ testing was conducted on a transparent test cell to visu- alize the water droplet formation and detachment on the surface of different types of GDLs through a CCD cam- era. The breakthrough pressure, at which the liquid water penetrates the GDL and starts to form a droplet, was measured. The breakthrough pressure was found to be different for the GDLs with different porosities and thick- nesses. The equilibrium pressure, which is defined as the minimum pressure required maintaining a constant flow through the GDL, was also recorded. The equilibrium pressure was found to be much lower than the breakthrough pressure for the same type of GDL. A pore network model was modified to further study the relationship between the breakthrough pressure and the GDL properties and thicknesses. The breakthrough pressure increases for the thick GDL with smaller micro-pore size.     

A Pt content and pore structure gradient distributed catalyst layer to improve the PEMFC performance

The catalyst layer is a key component in the proton exchange membrane fuel cell (PEMFC) for it is where the conversion of fuel into electricity takes place. Traditionally, electrocatalyst is uniformly distributed in the catalyst layers of the membrane electrode assembly (MEA) and the high Pt consumption in catalyst layers blocks the widely use of PEMFC. Here we proposed a Pt content and pore structure gradient distributed, two-layer catalyst layer for PEMFC to improve the MEA performance. Energy-dispersive X-ray (EDX) spectroscopy results show Pt nanoparticles gradient distributed on the vertical direction of catalyst layer. The pore size in the Pt poor layer is larger than that in the Pt rich layer, and this structure can improve the Pt utilization and enhance the mass transfer in the catalyst layer. The single cell test result shows this new MEA has a better performance (11%) than the traditional MEA.     

Degradation of gas diffusion layers through repetitive freezing

This work investigates the degradation of an individual gas diffusion layer (GDL) by repeated freezing cycles. The pore size distribution, gas permeability, surface structure, and contact angle on the surface of the GDL were measured in four different types of GDL: SGL paper with a microporous layer (MPL); SGL paper with 5 wt% of polytetrafluoroethylene (PTFE) loading; Toray paper without PTFE loading; and Toray paper with 20 wt% of PTFE loading. After repeated freezing cycles, the porosity of the GDL without PTFE was reduced by 27.2% due to the volumetric expansion of the GDL. The peak of the log differential intrusion moved toward a smaller pore diameter slightly because of the repeated freezing process. The crack of the MPL increased in its width and length after repeated freezing cycles. The through-plane gas permeability of the GDL with the MPL doubled after repeated freezing cycles due to the growth of the crack in the MPL, but was very small for the GDLs with Toray paper. Besides, the GDLs with PTFE loading showed a relatively larger decrease in the contact angle on the surface than the GDL without PTFE loading due to the separation of PTFE from the carbon fiber during the repeated freezing process.     

Steady saturation distribution in hydrophobic gas-diffusion layers of polymer electrolyte membrane fuel cells: A pore-network study

A pore-network model is developed to simulate liquid water transport in a hydrophobic gas-diffusion layer (GDL) during the operation of polymer electrolyte membrane fuel cells (PEMFCs). The steady saturation distribution in GDLs is determined through a numerical procedure using a pore-network model combined with invasion-percolation path-finding and subsequent viscous two-phase flow calculation. The simulation results indicate that liquid water transport in hydrophobic GDLs is a strongly capillary-driven process that almost reaches the pure invasion-percolation limit with zero capillary number. A uniform flux condition is found to better reflect the actual phenomenon occurring at the inlet boundary for liquid water entering a GDL than a uniform pressure condition. The simulation further clarifies the effect of the invaded pore fraction at a uniform-flux inlet boundary in modifying water transport in GDLs. Finally, the effect of the GDL thickness on the steady saturation distribution is investigated.     

Gas diffusion layer deformation and its effect on the transport characteristics and performance of proton exchange membrane fuel cell

Cell/stack assembly force can strongly affect the transport characteristics and performance of a proton exchange membrane fuel cell (PEMFC) through causing the structural deformation. In this study, a mathematical model has been developed to investigate the effect of the assembly force for different gas diffusion layers (GDL) and membranes. The results indicate that the predominant deformation of the cell structure occurs in the porous GDL due to its weak mechanical strength. Thicker GDLs result into lower water content in the GDL structure, and can sustain a larger assembly force without the risk of “electrode flooding”; while thinner GDLs have higher water content, can maintain the hydration required for the membrane, and yield a better cell performance with less sensitivity to the variations in the assembly force. Thinner membranes yield better cell performance, but the cell performance is more sensitive to the changes in the assembly force. A combination of thin GDL and membrane is beneficial for better cell performance with reasonable sensitivity to the assembly force. For thinner GDLs, an optimal assembly force exists beyond which the cell performance is reduced; and practical cell assembly force will limit the GDL thickness.