Charge–discharge characteristics of all-solid-state thin-filmed lithium-ion batteries using amorphous Nb2O5 negative electrodes

All-solid-state thin-filmed lithium-ion rechargeable batteries composed of amorphous Nb₂O₅ negative electrode with the thickness of 50–300 nm and amorphous Li₂Mn₂O₄ positive electrode with a constant thickness of 200 nm, and amorphous Li₃PO_4−xN_x electrolyte (100 nm thickness), have been fabricated on glass substrates with a 50 mm × 50 mm size by a sputtering method, and their electrochemical characteristics were investigated. The charge–discharge capacity based on the volume of positive electrode increased with increasing thickness of negative electrode, reaching about 600 mAh cm⁻³ for the battery with the negative electrode thickness of 200 nm. But the capacity based on the volume of both the positive and negative electrodes was the maximum value of about 310 mAh cm⁻³ for the battery with the negative electrode thickness of 100 nm. The shape of charge–discharge curve consisted of a two-step for the batteries with the negative electrode thickness more than 200 nm, but that with the thickness of 100 nm was a smooth S-shape curve during 500 cycles.     

Synthesis of single crystalline Li0.44MnO2 nanowires with large specific capacity and good high current density property for a positive electrode of Li ion battery

The fabrication of single crystalline Li_0.44MnO₂ nanowires for the positive electrode of lithium ion battery is reported. The single crystalline Li_0.44MnO₂ nanowires are obtained by lithium exchange reaction of Na_0.44MnO₂ nanowires with high aspect ratio. The Li_0.44MnO₂ nanowires indicate both the large specific capacity of around 250 mAh g⁻¹ (1.5-4.5 V vs. Li/Li⁺) and the good high current density property for the positive electrode of lithium ion battery.     

Basic molten salt process—A new route for synthesis of nanocrystalline Li4Ti5O12-TiO2 anode material for Li-ion batteries using eutectic mixture of LiNO3-LiOH-Li2O2

A nanocrystalline Li₄Ti₅O₁₂-TiO₂ duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO₃-LiOH-Li₂O₂ at 400-500 °C. The microstructure and morphology of the Li₄Ti₅O₁₂-TiO₂ product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li₄Ti₅O₁₂; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li₄Ti₅O₁₂-TiO₂; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g⁻¹ at 0.2 C, 168 mAh g⁻¹ at 0.5 C, 146 mAh g⁻¹ at 1 C, 135 mAh g⁻¹ at 2 C, and 117 mAh g⁻¹ at 5 C. After 100 cycles, the discharge capacity is 138 mAh g⁻¹ at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li₄Ti₅O₁₂ and the anatase TiO₂.     

High power and high capacity cathode material LiNi0.5Mn0.5O2 for advanced lithium-ion batteries

Single-phase lithium nickel manganese oxide, LiNi_0.5Mn_0.5O₂, was successfully synthesized from a solid solution of Ni_1.5Mn_1.5O₄ that was prepared by means of the solid reaction between Mn(CH₃COO)₂·4H₂O and Ni(CH₃COO)₂·4H₂O. XRD pattern shows that the product is well crystallized with a high degree of Li–M (Ni, Mn) order in their respective layers, and no diffraction peak of Li₂MnO₃ can be detected. Electrochemical performance of as-prepared LiNi_0.5Mn_0.5O₂ was examined in the test battery by charge–discharge cycling with different rate, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The cycling behavior between 2.5 and 4.4 V at a current rate of 21.7 mA g⁻¹ shows a reversible capacity of about 190 mAh g⁻¹ with little capacity loss after 100 cycles. High-rate capability test shows that even at a rate of 6C, stable capacity about 120 mAh g⁻¹ is retained. Cyclic voltammetry (CV) profile shows that the cathode material has better electrochemical reversibility. EIS analysis indicates that the resistance of charge transfer (R_ct) is small in fully charged state at 4.4 V and fully discharged state at 2.5 V versus Li⁺/Li. The favorable electrochemical performance was primarily attributed to regular and stable crystal structure with little intra-layer disordering.     

Effect of Cr doping on the structural,electrochemical properties of Li[Li0.2Ni0.2−x/2Mn0.6−x/2Crx]O2 (x = 0, 0.02, 0.04, 0.06, 0.08) as cathode materials for lithium secondary batteries

Prospective positive-electrode (cathode) materials for a lithium secondary battery, viz., Li[Li_0.2Ni_0.2−x/2Mn_0.6−x/2Cr_x]O₂ (x = 0, 0.02, 0.04, 0.06, 0.08), were synthesized using a solid-state pyrolysis method. The structural and electrochemical properties were examined by means of X-ray diffraction, cyclic voltammetry, SEM and charge–discharge tests. The results demonstrated that the powders maintain the α-NaFeO₂-type layered structure regardless of the chromium content in the range x ≤ 0.08. The Cr doping of x = 0.04 showed improved capacity and rate capability comparing to undoped Li[Li_0.2Ni_0.2Mn_0.6]O₂. ac impedance measurement showed that Cr-doped electrode has the lower impedance value during cycling. It is considered that the higher capacity and superior rate capability of Cr-doping samples would be ascribed to the reduced resistance of the electrode during cycling.     

Characterization of electrolytic Co3O4 thin films as anodes for lithium-ion batteries

The electrolytic deposition of Co₃O₄ thin films on stainless steel was conducted in Co(NO₃)₂ aqueous solution for anodes in lithium-ion thin film batteries. Three major electrochemical reactions during the deposition were discussed. The coated specimens and the coating films carried out at −1.0 V (saturated KCl Ag/AgCl) were subjected to annealing treatments and further characterized by XRD, TGA/DTA, FE-SEM, Raman spectroscopy, cyclic voltammetry (CV) and discharge/charge cyclic tests. The as-coated film was β-Co(OH)₂, condensed into CoO and subsequently oxidized into nano-sized Co₃O₄ particles. The nano-sized Co₃O₄, CoO, Li₂O and Co particles revealed their own characteristics different from micro-sized ones, such as more interfacial effects on chemical bonding and crystallinity. The initial maximum capacity of Co₃O₄ coated specimen was 1930 mAh g⁻¹ which much more than its theoretical value 890 mAh g⁻¹, since the nano-sized particles offered more interfacial bondings for extra sites of Li⁺ insertion. However, a large ratio of them was trapped, resulting in a great part of irreversible capacity during the first charging. Still, it revealed a capacity 500 mAh g⁻¹ after 50 discharged-charged cycles.     

Mitigation of the irreversible capacity and electrolyte decomposition in a LiNi0.5Mn1.5O4/nano-TiO2 Li-ion battery

Nanosized titanium oxides can achieve large reversible specific capacity (above 200 mAh g⁻¹) and good rate capabilities, but suffer irreversible capacity losses in the first cycle. Moreover, due to the intrinsic safe operating potential (1.5 V), the use of titanium oxide requires to couple it with high-potential cathodes, such as lithium nickel manganese spinel (LNMO) in order to increase the energy density of the final cell. However the use of the 4.7 V vs. Li⁺/Li⁰ LNMO cathode material requires to tackle the continuous electrolyte decomposition upon cycling. Coupling these two electrodes to make a lithium ion battery is thus highly appealing but also highly difficult because the cell balancing must account not only for the charge reversibly exchanged by each electrode but also for the irreversible charge losses. In this paper a LNMO-nano TiO₂ Li-ion cell with liquid electrolyte is presented: two innovative approaches on both the cathode and the anode sides were developed in order to mitigate the electrolyte decomposition upon cycling. In particular the LNMO surface was coated with ZnO in order to minimize the surface reactivity, and the TiO₂ nanoparticles where activated by incorporating nano-lithium in the electrode formulation to compensate for the irreversible capacity loss in the first cycle. With these strategies we were able to assemble balanced Li-ion coin cells thus avoiding the use of electrolyte additives and more hazardous and expensive ex-situ SEI preforming chemical or electrochemical procedures.     

Effects of roasting temperature and modification on properties of Li2FeSiO4/C cathode

Li₂FeSiO₄/C cathodes were synthesized by combination of wet-process method and solid-state reaction at high temperature, and effects of roasting temperature and modification on properties of the Li₂FeSiO₄/C cathode were investigated. The XRD patterns of the Li₂FeSiO₄/C samples indicate that all the samples are of good crystallinity, and a little Fe₃O₄ impurity was observed in them. The primary particle size rises as the roasting temperature increases from 600 to 750 °C. The Li₂FeSiO₄/C sample synthesized at 650 °C has good electrochemical performances with an initial discharge capacity of 144.9 mAh g⁻¹ and the discharge capacity remains 136.5 mAh g⁻¹ after 10 cycles. The performance of Li₂FeSiO₄/C cathode is further improved by modification of Ni substitution. The Li₂Fe_0.9Ni_0.1SiO₄/C composite cathode has an initial discharge capacity of 160.1 mAh g⁻¹, and the discharge capacity remains 153.9 mAh g⁻¹ after 10 cycles. The diffusion coefficient of lithium in Li₂FeSiO₄/C is 1.38 × 10⁻¹² cm² s⁻¹ while that in Li₂Fe_0.9Ni_0.1SiO₄/C reaches 3.34 × 10⁻¹² cm² s⁻¹.     

Electrochemical activity of Li2FeTiO4 and Li2MnTiO4 as potential active materials for Li ion batteries: A comparison with Li2NiTiO4

We demonstrate, for the first time, a considerable electrochemical activity of two members of lithium transition element titanates: Li₂FeTiO₄ and Li₂MnTiO₄. Both materials consist of 10–20 nm particles embedded in a conductive carbon coating. We show that not the coating but the small particle size is decisive for materials’ activity. Li₂FeTiO₄ shows a stable reversible capacity of up to 123 mA hg⁻¹ at C/20 and 60 °C which is 83% of the theoretical value for exchange of 1 electron (148 mA hg⁻¹). Li₂MnTiO₄ could only be prepared in a nanosized form that contained about 30% of impurities. The capacity of the whole material (including impurities) is comparable to that of Li₂FeTiO₄ but the cycling stability is much poorer. In contrast to the Fe and Mn analogues, the third member of the titanate family, Li₂NiTiO₄, shows a good electrochemistry even when the particle size is much larger (about 100 nm). During initial cycles at C/10 and 60 °C, exchange of more than 1 electron per compound formula has been observed. The cycling stability at high temperatures, however, is poor.     

Electrochemical deposition of porous Co3O4 nanostructured thin film for lithium-ion battery

Porous Co₃O₄ nanostructured thin films are electrodeposited by controlling the concentration of Co(NO₃)₂ aqueous solution on nickel sheets, and then sintered at 300 °C for 3 h. The as-prepared thin films are characterized by thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The electrochemical measurements show that the highly porous Co₃O₄ thin film with the highest electrochemically active specific surface area (68.64 m² g⁻¹) yields the best electrochemical performance compared with another, less-porous film and with a non-porous film. The highest specific capacity (513 mAh g⁻¹ after 50 cycles) is obtained from the thinnest film with Co₃O₄ loaded at rate of 0.05 mg cm⁻². The present research demonstrates that electrode morphology is one of the crucial factors that affect the electrochemical properties of electrodes.     

High-rate performance of all-solid-state lithium secondary batteries using Li4Ti5O12 electrode

The all-solid-state Li–In/Li₄Ti₅O₁₂ cell using the 80Li₂S·20P₂S₅ (mol%) solid electrolyte was assembled to investigate rate performances. It was difficult to obtain the stable performance at the charge current density of 3.8 mA cm⁻² in the all-solid-state cell. In order to improve the rate performance, the pulverized Li₄Ti₅O₁₂ particles were applied to the all-solid-state cell, which retained the reversible capacity of about 90 mAh g⁻¹ at 3.8 mA cm⁻². The 70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic, which exhibits the higher lithium ion conductivity than the 80Li₂S·20P₂S₅ solid electrolyte, was also used. The Li–In/70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic/pulverized Li₄Ti₅O₁₂ cell was charged at a current density higher than 3.8 mA cm⁻² and showed the reversible capacity of about 30 mAh g⁻¹ even at 10 mA cm⁻² at room temperature.     

Hybrid supercapacitor based on MnO2 and columned FeOOH using Li2SO4 electrolyte solution

The nano-sized columned β-FeOOH was prepared by the hydrolysis process and its electrochemical capacitance performance was evaluated for the first time in Li₂SO₄ solution. A hybrid supercapacitor based on MnO₂ positive electrode and FeOOH negative electrode in Li₂SO₄ electrolyte solution was designed. The electrochemical tests demonstrated that the hybrid supercapacitor has a energy density of 12 Wh kg⁻¹ and a power density of 3700 W kg⁻¹ based on the total weight of the electrode active materials with a voltage range 0–1.85 V. This hybrid supercapacitor also exhibits a good cycling performance and keeps 85% of initial capacity over 2000 cycles.     

High-density spherical Li4Ti5O12/C anode material with good rate capability for lithium ion batteries

Li₄Ti₅O₁₂ is a very promising anode material for lithium secondary batteries. To improve the material's rate capability and pile density is considered as the important researching direction. One effective way is to prepare powders composed of spherical particles containing carbon black. A novel technique has been developed to prepare spherical Li₄Ti₅O₁₂/C composite. The spherical precursor containing carbon black is prepared via an “outer gel” method, using TiOCl₂, C and NH₃ as the raw material. Spherical Li₄Ti₅O₁₂/C powders are synthesized by sintering the mixture of spherical precursor and Li₂CO₃ in N₂. The investigation of TG/DSC, SEM, XRD, Brunauer–Emmett–Teller (BET) testing, laser particle size analysis, tap-density testing and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂/C composite prepared by this method are spherical, has high tap-density and excellent rate capability. It is observed that the tap-density of spherical Li₄Ti₅O₁₂/C powders (the mass content of C is 4.8%) is as high as 1.71 g cm⁻³, which is remarkably higher than the non-spherical Li₄Ti₅O₁₂. Between 1.0 and 3.0 V versus Li, the initial discharge specific capacity of the sample is as high as 144.2 mAh g⁻¹, which is still 128.8 mAh g⁻¹ after 50 cycles at a current density of 1.6 mA cm⁻².     

Mesoporous nano-Co3O4: A potential negative electrode material for alkaline secondary battery

A potential negative electrode material (mesoporous nano-Co₃O₄) is synthesized via a simple thermal decomposition of precursor Co(OH)₂ hexagonal nanosheets in the air. The structure and morphology of the samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It is found that the nano-Co₃O₄ is present in mesoporous hexagonal nanoparticles. The average size of holes is about 5-15 nm. The electrochemical performances of mesoporous nano-Co₃O₄ as the active starting negative electrode material for alkaline secondary battery are investigated by galvanostatic charge-discharge and cyclic voltammetry (CV) technique. The results demonstrate that the prepared mesoporous nano-Co₃O₄ electrode displays excellent electrochemical performance. The discharge capacity of the mesoporous nano-Co₃O₄ electrode can reach 436.5 mAh g⁻¹ and retain about 351.5 mAh g⁻¹ after 100 cycles at discharge current of 100 mA g⁻¹. A properly electrochemical reaction mechanism of mesoporous nano-Co₃O₄ electrode is also constructed in detail.     

A porous spherical aggregation of Li4Mn5O12 nanorods and its electrochemical performance

A porous spherical aggregation of Li₄Mn₅O₁₂ nanorods with the particle size of 3 μm is prepared by oxidizing LiMn₂O₄ powder with (NH₄)₂S₂O₈ under hydrothermal conditions. The result displays that concentration of (NH₄)₂S₂O₈ plays a key role in forming the porous spherical aggregation and the optimal concentration of oxidant is found to be 1.5 mol L⁻¹. The mechanism for the formation of the porous spherical aggregation is proposed. The electrochemical capacitance performance is tested by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge/discharge. The porous spherical aggregation exhibits a good electrochemical performance. It could deliver 375 F g⁻¹ within potential range 0-1.4 V at a scan rate of 5 mV s⁻¹ in 1 mol L⁻¹ Li₂SO₄ and the value is cut down to less than 0.024 F g⁻¹ per cycling period in 1000 cycles.     

Effects of dopant on the electrochemical performance of Li4Ti5O12 as electrode material for lithium ion batteries

The effects of dopant on the electrochemical properties of spinel-type Li_3.95M_0.15Ti_4.9O₁₂ (M = Al, Ga, Co) and Li_3.9Mg_0.1Al_0.15Ti_4.85O₁₂ were systematically investigated. Charge–discharge cycling were performed at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.3 and 0.5 V, the experimental results showed that Al³⁺ dopant greatly improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Ga³⁺ slightly increased the capacity of the Li₄Ti₅O₁₂, but did not essentially alleviate the degradation of cycling stability. Dopants such as Co³⁺ and Mg²⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

Li3V2(PO4)3 cathode material synthesized by chemical reduction and lithiation method

The monoclinic-type Li₃V₂(PO₄)₃ cathode material was synthesized via calcining amorphous Li₃V₂(PO₄)₃ obtained by chemical reduction and lithiation of V₂O₅ using oxalic acid as reducer and lithium carbonate as lithium source in alcohol solution. The amorphous Li₃V₂(PO₄)₃ precursor was characterized by using TG–DSC and XPS. The results showed that the V⁵⁺ was reduced to V³⁺ by oxalic acid at ambient temperature and pressure. The prepared Li₃V₂(PO₄)₃ was characterized by XRD and SEM. The results indicated the Li₃V₂(PO₄)₃ powder had good crystallinity and mesoporous morphology with an average diameter of about 30 nm. The pure Li₃V₂(PO₄)₃ exhibits a stable discharge capacity of 130.08 mAh g⁻¹ at 0.1 C (14 mA g⁻¹).     

Structural and electrochemical characterization of xLi[Li1/3Mn2/3]O2·(1 − x)Li[Ni1/3Mn1/3Co1/3]O2 (0 ≤ x ≤ 0.9) as cathode materials for lithium ion batteries

A series of cathode materials with molecular notation of xLi[Li_1/3Mn_2/3]O₂·(1 − x)Li[Ni_1/3Mn_1/3Co_1/3]O₂ (0 ≤ x ≤ 0.9) were synthesized by combination of co-precipitation and solid state calcination method. The prepared materials were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques, and their electrochemical performances were investigated. The results showed that sample 0.6Li[Li_1/3Mn_2/3]O₂·0.4Li[Ni_1/3Mn_1/3Co_1/3]O₂ (x = 0.6) delivers the highest capacity and shows good capacity-retention, which delivers a capacity ∼250 mAh g⁻¹ between 2.0 and 4.8 V at 18 mA g⁻¹.     

Synthesis and electrochemical properties of Li1−xFe0.8Ni0.2O2–LixMnO2 (Mn/(Fe + Ni + Mn) = 0.8) material

A new type of Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ (Mn/(Fe + Ni + Mn) = 0.8) material was synthesized at 350 °C in air atmosphere using a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−xFeO₂–Li_xMnO₂ (Mn/(Fe + Mn) = 0.8) with much reduced impurity peaks. The Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell showed a high initial discharge capacity above 192 mAh g⁻¹, which was higher than that of the parent Li/Li_1−xFeO₂–Li_xMnO₂ (186 mAh g⁻¹). We expected that the increase of initial discharge capacity and the change of shape of discharge curve for the Li/Li_1−xFe_0.8Ni_0.2O₂–Li_xMnO₂ cell is the result from the redox reaction from Ni²⁺ to Ni³⁺ during charge/discharge process. This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles.     

Preparation of manganese oxide with high density by decomposition of MnCO3 and its application to synthesis of LiMn2O4

Manganese oxide with high tap density was prepared by decomposition of spherical manganese carbonate, and then LiMn₂O₄ cathode materials were synthesized by solid-state reaction between the manganese oxide and lithium carbonate. Structure and properties of the samples were determined by X-ray diffraction, Brunauer–Emmer–Teller surface area analysis, scanning electron microscope and electrochemical measurements. With increase of the decomposition temperature from 350 °C to 900 °C, the tap density of the manganese oxide rises from 0.91 g cm⁻³ to 2.06 g cm⁻³. Compared with the LiMn₂O₄ cathode made from chemical manganese dioxide or electrolytic manganese dioxide, the LiMn₂O₄ made from manganese oxide of this work has a larger tap density (2.53 g cm⁻³), and better electrochemical performances with an initial discharge capacity of 117 mAh g⁻¹, a capacity retention of 93.5% at the 15th cycle and an irreversible capacity loss of 2.24% after storage at room temperature for 28 days.