Crosslinked SPEEK/AMPS blend membranes with high proton conductivity and low methanol diffusion coefficient for DMFC applications

The crosslinked sulfonated poly (ether ether ketone)/2-acrylamido-2-methyl-1-propanesulfonic acid (SPEEK/AMPS) blend membranres were prepared and evaluated as proton exchange membranes for direct methanol fuel cell (DMFC) applications. The structure and morphology of SPEEK/AMPS membranes were characterized by FTIR and SEM, respectively. The effects of crosslinking and AMPS content on the performance of membranes were studied and discussed in detail. The proton conductivity and methanol diffusion coefficient of SPEEK/AMPS membranes increased gradually with the increase of AMPS content. Most SPEEK/AMPS membranes exhibited higher proton conductivity than Nafion^® 117 (0.05 S cm⁻¹ at 25 °C). However, all the membranes possessed much lower methanol diffusion coefficient compared with Nafion^® 117 (2.38 × 10⁻⁶ cm² s⁻¹) under the same measuring conditions. Even the methanol diffusion coefficient (8.89 × 10⁻⁷ cm² s⁻¹) of SPEEK/AMPS 30 sample with the highest proton conductivity (0.084 S cm⁻¹ at 25 °C) was only about one third of that of Nafion^® 117. The selectivity of all the SPEEK/AMPS membranes was much higher in comparison with Nafion^® 117 (2.8 × 10⁴ S s cm⁻³). In addition, the SPEEK/AMPS membranes possessed relatively good thermal and hydrolytic stability. These results suggested that the SPEEK/AMPS membranes were particularly promising to be used as proton exchange membranes in DMFCs, and the high proton conductivity, low methanol diffusion coefficient and high selectivity were their primary advantages for DMFC applications.     

Sulfonated poly(ether ether ketone) membranes with sulfonated graphene oxide fillers for direct methanol fuel cells

Sulfonated organosilane functionalized graphene oxides (SSi-GO) synthesized through the grafting of graphene oxide (GO) with 3-mercaptopropyl trimethoxysilane and subsequent oxidation have been used as a filler in sulfonated poly(ether ether ketone) (SPEEK) membranes. The incorporation of SSi-GOs greatly increases the ion-exchange capacity (IEC), water uptake, and proton conductivity of the membrane. With well-controlled contents of SSi-GOs, the composite membranes exhibit higher proton conductivity and lower methanol permeability than Nafion^® 112 and Nafion^® 115, making them particularly attractive as proton exchange membranes (PEMs) for direct methanol fuel cells (DMFC). The composite membrane with optimal SSi-GOs content exhibit over 38 and 17% higher power densities, respectively, than Nafion^® 112 and Nafion^® 115 membranes in DMFCs, offering the possibilities to reduce the DMFC membrane cost significantly while keeping high-performance.     

Nafion/nitrated sulfonated poly(ether ether ketone) membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone)s (SPEEKs) are substituted on the main chain of the polymer by nitro groups and blended with Nafion^® to attain composite membranes. The sulfonation, nitration and blending are achieved with a simple, inexpensive process, and the blended membranes containing the nitrated SPEEKs reveal a liquid-liquid phase separation. The blended membranes have a lower water uptake compared to recast Nafion^®, and the methanol permeability is reduced significantly to 4.29 × 10⁻⁷-5.34 × 10⁻⁷ cm² s⁻¹ for various contents of nitrated SPEEK for S63N17, and 4.72 × 10⁻⁷-7.11 × 10⁻⁷ cm² s⁻¹ for S63N38, with a maximum proton conductivity of ∼0.085 S cm⁻¹. This study examines the single-cell performance at 80 °C of Nafion^®/nitrated SPEEK membranes with various contents of nitrated SPEEK and a degree of nitration of 23-25 mW cm⁻² for S63N17 and 24-29 mW cm⁻² for S63N38. Both the power density and open circuit voltage are higher than those of Nafion^® 115 and recast Nafion^®.     

Semi-interpenetrating polymer network electrolyte membranes composed of sulfonated poly(ether ether ketone) and organosiloxane-based hybrid network

A semi-interpenetrating polymer network (semi-IPN) proton exchange membrane is prepared from the sulfonated poly(ether ether ketone) (sPEEK) and organosiloxane-based organic/inorganic hybrid network (organosiloxane network). The organosiloxane network is synthesized from 3-glycidyloxypropyltrimethoxysiane and 1-hydroxyethane-1,1-diphosphonic acid. The semi-IPN membranes prepared were stable up to 300 °C without any degradation. The methanol permeability is much lower than Nafion^® 117 under addition of the organosiloxane network. The proton conductivity of semi-IPN membranes increases with an increase the organosiloxane network content; the membrane containing the 20-24 wt% organosiloxane network shows higher conductivity than Nafion^® 117. The power density of the MEA fabricated with the semi-IPN membrane with 24 wt% organosiloxane network is 135 mW cm⁻², much better than that of the pristine sPEEK membrane, 85 mW cm⁻². Chemical synthesis of the semi-IPN membranes is identified using FTIR, and its ion cluster dimension examined using SAXS. The dimensional stability associated with water swelling and dissolution is investigated at different temperatures, and the semi IPN membranes dimensionally stable in water at elevated temperature.     

Preparation and properties of crosslinked sulphonated poly(arylene ether sulphone) blend s for direct methanol fuel cell applications

HMS-based sulphonated poly(arylene ether sulphone) (HMSSH) is synthesised using 4,4′-dihydroxy-α-methylstilbene (HMS) monomer to introduce an interesting stilbene core as crosslinkable group. Crosslinked blend membranes are obtained by blending the BPA-based sulphonated poly(arylene ether sulphone) (BPASH) with crosslinkable HMS-based sulphonated poly(arylene ether sulphone) by UV irradiation of the blend membrane. Compared to the native BPASH with crosslinked BPASH/HMSSH blend membranes, the crosslinked blend membranes greatly reduce the water uptake and methanol permeability with only a slight reduction in proton conductivity. The crosslinked blend membrane, which has a 6% HMSSH content, has a water uptake of 59%, methanol permeability of 0.75 × 10⁻⁶ cm² s⁻¹, and proton conductivity of 0.08 S cm⁻¹. A membrane-electrode assembly is used to investigate single-cell performance and durability test for DMFC applications. Both the power density and open circuit voltage are higher than those of Nafion^® 117. A maximum power density of 32 mW cm⁻² at 0.2 V is obtained at 80 °C, which is higher than that of Nafion^® 117 (25 mW cm⁻²).     

A study on fabrication of sulfonated poly(ether ether ketone)-based membrane-electrode assemblies for polymer electrolyte membrane fuel cells

The porosity effect of catalyst electrodes in membrane-electrode assemblies (MEAs) using a hydrocarbon-based polymer as electrolyte and ionomer was investigated on physical and electrochemical properties by varying the content of ionomer binder (dry condition) in the catalyst electrodes. The MEAs were compared with the Nafion^®-based MEA using Nafion^® 112 and 5 wt.% ionomer solution (EW = 1100) in terms of porosity values, scanning electron microscopic images, Nyquist plots, dielectric spectra and I–V polarization curves. In this study, sulfonated poly(ether ether ketone) (SPEEK) membranes with 25 ± 5 μm of thickness and 5 wt.% ionomer solutions have been prepared. The prepared membranes were characterized in terms of FT-IR, DSC and proton conductivity. Proton conductivity of the SPEEK membranes was compared with one of the Nafion^® membranes with relative humidity. The porosity of the catalyst electrodes was calculated using the properties of catalyst, ionomer solution and solvent. As a result, the performance of the new type polymer (i.e., SPEEK in this study)-based MEA with the similar membrane conductivity and porosity of the catalyst electrode in the Nafion^® MEA was similar to that of the Nafion^® MEA.     

Blended Nafion/SPEEK direct methanol fuel cell membranes for reduced methanol permeability

Sulfonated poly(ether ether ketone)s (SPEEKs) were substituted on a polymer main chain that had previously been prepared by sulfonation of poly(ether ether ketone)s in concentrated sulfuric acid for a specified time. The product was then blended with Nafion^® to create composite membranes. The blended SPEEK-containing membranes featured flaky domains dispersed in the Nafion^® matrix. These blends possessed a high thermal decomposition temperature. Additionally, owing to the more crystalline, the blended membranes had a lower water uptake compared to recast Nafion^®, the methanol permeability was reduced to 1.70 × 10⁻⁶ to 9.09 × 10⁻⁷ cm² s⁻¹ for various SPEEK concentrations, and a maximum proton conductivity of ∼0.050 S cm⁻¹ was observed at 30 °C. The single-cell performances of the Nafion^®/SPEEK membranes, with various SPEEK concentrations and a certain degree of sulfonation, were 15–25 mW cm⁻² for SPEEK53 and 19–27 mW cm⁻² for SPEEK63, at 80 °C. The power density and open circuit voltage were higher than those of Nafion^® 115 (power density = 22 mW cm⁻²). The blended membranes satisfy the requirements of proton exchange membranes for direct methanol fuel cell (DMFC) applications.     

Novel modification method to prepare crosslinked sulfonated poly(ether ether ketone)/silica hybrid membranes for fuel cells

Crosslinked organic-inorganic hybrid membranes are prepared from hydroxyl-functionalized sulfonated poly(ether ether ketone) (SPEEK) and various amounts of silica with the aims to improve dimensional stability and methanol resistance. The partially hydroxyl-functionalized SPEEK is prepared by the reduction of some benzophenone moieties of SPEEK into the corresponding benzhydrol moieties which is then reacted with (3-isocyanatopropyl)triethoxysilane (ICPTES) to get a side chained polymer bearing triethoxysilyl groups. These groups are subsequently co-hydrolyzed with tetraethoxysilane (TEOS) and allow the membrane to form a crosslinked network via a sol-gel process. The obtained hybrid membranes with covalent bonds between organic and inorganic phases exhibit much lower methanol swelling ratio and water uptake. With the increase of silica content, the methanol permeability coefficient of the hybrid membranes decreases at first and then increased. At silica content of about 6 wt.%, the methanol permeability coefficient reaches a minimum of 7.15 × 10⁻⁷ cm² s⁻¹, a 5-fold decrease compared with that of the pristine SPEEK. Despite the fact that the proton conductivity is decreased to some extent as a result of introduction of the silica, the hybrid membranes with silica content of 4-8 wt.% shows higher selectivity than Nafion117.     

Investigation of the effects of AMPS-modified nanoclay on fuel cell performance of sulfonated aromatic proton exchange membranes

Here we describe preparation and characterization of a series of nanocomposite polyelectrolytes based on partially sulfonated poly (ether ether ketone) (SPEEK) and organically modified montmorillonite (MMT). Optimum degree of sulfonation for SPEEK is selected based on its transport properties. MMT is modified via ion exchange reaction using a 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as a functional modifier. AMPS-MMT at different loadings is introduced into the SPEEK matrices via the solution intercalation technique. Also, the nanocomposite membranes are fabricated using SPEEK and commercially available nanoclays like Cloisite Na (Na-MMT) and Cloisite 15A. Transport properties, proton conductivity and methanol permeability of the fabricated composite membranes are evaluated. Presence of AMPS-MMT significantly decreases the activation energy needed for proton conductivity. A membrane based on SPEEK/AMPS-MMT-3 wt% is selected as an optimum formulation which exhibits a high selectivity and power density at the elevated methanol concentrations. Moreover, it is found that the optimum nanocomposite membrane not only provides higher power output compared to the neat SPEEK and Nafion^®117 membranes, but also exhibits a higher open circuit voltage (OCV) in comparison with pristine SPEEK and commercial Nafion^® 117 membranes. Owing to the desirable transport and electrochemical properties SPEEK/AMPS-MMT nanocomposite can be considered as an alternative membrane for direct methanol fuel cell applications.     

Use of in situ polymerized phenol-formaldehyde resin to modify a Nafion membrane for the direct methanol fuel cell

Commercial Nafion^®-115 (trademark registered to DuPont) membranes were modified by in situ polymerized phenol formaldehyde resin (PFR) to suppress methanol crossover, and SO₃⁻ groups were introduced to PFR by post-sulfonatation. A series of membranes with different sulfonated phenol formaldehyde resin (sPFR) loadings have been fabricated and investigated. SEM-EDX characterization shows that the PFR was well dispersed throughout the Nafion^® membrane. The composite membranes have a similar or slightly lower proton conductivity compared with a native Nafion^® membrane, but show a significant reduction in methanol crossover (the methanol permeability of sPFR/Nafion^® composite membrane with 2.3 wt.% sPFR loading was 1.5 × 10⁻⁶ cm² s⁻¹, compared with the 2.5 × 10⁻⁶ cm² s⁻¹ for the native Nafion^® membrane). In direct methanol fuel cell (DMFC) evaluation, the membrane electrode assembly (MEA) using a composite membrane with a 2.3 wt.% sPFR loading shows a higher performance than that of a native Nafion^® membrane with 1 M methanol feed, and at higher methanol concentrations (5 M), the composite membrane achieved a 114 mW cm⁻² maximum power density, while the maximum power density of the native Nafion^® was only 78 mW cm⁻².     

Novel sulfonated poly(ether ether ketone)s containing nitrile groups and their composite membranes for fuel cells

A series of novel sulfonated poly(ether ether ketone)s containing a cyanophenyl group (SPEEKCNxx) are prepared based on (4-cyano)phenylhydroquinone via nucleophilic substitution polycondensation reactions. To further improve their properties, novel composite membranes composed of sulfonated poly(ether ether ketone)s containing cyanophenyl group as an acidic component and aminated poly(aryl ether ketone) as a basic component are successfully prepared. Most of the membranes exhibit excellent thermal, oxidative and dimensional stability, low-swelling ratio, high proton conductivity, low methanol permeability and high selectivity. The proton conductivities of the membranes are close to Nafion 117 at room temperature. And especially, the values of SPEEKCN40 and its composite membranes are higher than Nafion 117 at 80 °C (0.17 S cm⁻¹ of Nafion, 0.26 S cm⁻¹ of SPEEKCN40, 0.20 S cm⁻¹ of SPEEKCN40-1, and 0.18 S cm⁻¹ of SPEEKCN40-2). Moreover, the methanol permeability is one order magnitude lower than that of Nafion 117. All the data prove that both copolymers and their composite membranes may be potential proton exchange membrane for fuel cells applications.     

Proton exchange membranes based on semi-interpenetrating polymer networks of fluorine-containing polyimide and Nafion

A series of reinforced composite membranes as proton exchange membranes were prepared from Nafion^®212 and crosslinkable fluorine-containing polyimides (FPI). FPI was prepared from the polymerization of 4,4′-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), 2,2′-bis(trifluoromethyl)-4,4′-diaminobiphenyl (TFMB), and 3,5-diaminobenzoic acid (DABA). Then FPI was thermally crosslinked during the membrane preparation and formed the semi-interpenetrating polymer networks (semi-IPN) structure in the composite membranes. The thermal properties of the composite membranes were characterized by thermogravimetric analysis. The crosslinking density of FPI in the composite membranes was evaluated by the gel fraction. These membranes showed excellent thermal stabilities and good oxidative stabilities. Compared with Nafion^®212, the obtained composite membranes displayed much improved mechanical properties and dimensional stabilities. The tensile strength of the composite membranes was more than twice that of Nafion^®212. The composite membranes exhibited high proton conductivity, which ranged from 2.3 × 10⁻² S cm⁻¹ to 9.1 × 10⁻² S cm⁻¹. All membranes showed an increase in proton conductivity with temperature elevation.     

Preparation and characterization of self-crosslinked organic/inorganic proton exchange membranes

A series of silicon-containing sulfonated polystyrene/acrylate (Si-sPS/A) nanoparticles are successfully synthesized via simple emulsion polymerization method. The Si-sPS/A latexes show good film-forming capability and the self-crosslinked organic/inorganic proton exchange membranes are prepared by pouring the Si-sPS/A nanoparticle latexes into glass plates and drying at 60 °C for 10 h and 120 °C for 2 h. The potential of the membranes in direct methanol fuel cells (DMFCs) is characterized preliminarily by studying their thermal stability, ion-exchange capacity, water uptake, methanol diffusion coefficient, proton conductivity and selectivity (proton conductivity/methanol diffusion coefficient). The results indicate that these membranes possess excellent thermal stability and methanol barrier due to the existence of self-crosslinked silica network. In addition, the proton conductivity of the membranes is in the range of 10⁻³-10⁻² S cm⁻¹ and all the membranes show much higher selectivity in comparison with Nafion^® 117. These results suggest that the self-crosslinked organic/inorganic proton exchange membranes are particularly promising in DMFC applications.     

Effect of cesium salt of tungstophosphoric acid (Cs-TPA) on the properties of sulfonated polyether ether ketone (SPEEK) composite membranes for fuel cell applications

We have prepared composite membranes for fuel cell applications. Cesium salt of tungstophosphoric acid (Cs-TPA) particles was synthesized by aqueous solutions of tungstophosphoric acid and cesium hydroxide and, Cs-TPA particles and sulfonated (polyether ether ketone) (SPEEK) with two sulfonation degrees (DS), 60 and 70%have been used. We examined both the effects of Cs-TPA in SPEEK membranes as functions of sulfonation degrees of SPEEK and the content of Cs-TPA. The performance of the composite membranes was evaluated in terms of water uptake, ion exchange capacity, proton conductivity, chemical stability, hydrolytic stability, thermal stability and methanol permeability. The morphology of the membranes was investigated with SEM micrographs. Increasing sulfonation degree of SPEEK from 60 to 70 caused agglomeration of the Cs-TPA particles. The methanol permeability was reduced to 4.7 × 10⁻⁷ cm²/s for SPEEK (DS: 60%)/Cs-TPA membrane with 10 wt.% Cs-TPA concentration, and acceptable proton conductivity of 1.3 × 10⁻¹ S/cm was achieved at 80 °C under 100% RH. The weight loss at 900 °C increased with the addition of inorganic particles, as expected. The hydrolytic stability of the SPEEK/Cs-TPA based composite membranes was improved with the incorporation of the Cs-TPA particles into the matrix. We also noted that SPEEK60/Cs-TPA composite membranes were hydrolytically more stable than SPEEK70/Cs-TPA composite membranes. On the other hand, Methanol, water vapor, and hydrogen permeability values of SPEEK60 composite membranes were found to be lower than that of Nafion^®.     

Sulfonated titania submicrospheres-doped sulfonated poly(ether ether ketone) hybrid membranes with enhanced proton conductivity and reduced methanol permeability

Sulfonated titania submicrospheres (TiO₂-SO₃H) prepared through a facile chelation method are incorporated into sulfonated poly(ether ether ketone) (SPEEK) to fabricate organic-inorganic hybrid membranes with enhanced proton conductivity and reduced methanol permeability for potential use in direct methanol fuel cells (DMFCs). The pristine titania submicrospheres (TiO₂) with a uniform particle size are synthesized through a modified sol-gel method and sulfonated using 4,5-dihydroxy-1,3-benzenedisulfonic acid disodium salt as the sulfonation reagent. The sulfonation process is confirmed by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectra (XPS). The hybrid membranes are systematically characterized in terms of thermal property, mechanical property, ionic exchange capacity (IEC), swelling behavior, and microstructural features. The methanol barrier property and the proton conductivity of the SPEEK/TiO₂-SO₃H hybrid membranes are evaluated. The presence of the fillers reduces methanol crossover through the membrane. Compared with the unsulfonated TiO₂-doped membranes, the TiO₂-SO₃H-doped ones exhibit higher proton conductivity due to the additional sulfonic acid groups on the surface of TiO₂. The hybrid membrane doped with 15 wt.% TiO₂-SO₃H submicrospheres exhibits an acceptable proton conductivity of 0.053 S cm⁻¹ and a reduced methanol permeability of 4.19 × 10⁻⁷ cm² s⁻¹.     

Proton conducting CS/P(AA-AMPS) membrane with reduced methanol permeability for DMFCs

A novel polyelectrolyte complex (PEC) membrane for direct methanol fuel cells (DMFCs) was prepared by blending a cationic polyelectrolyte, chitosan (CS), with an anionic polyelectrolyte, acrylic acid-2-acrylamido-2-methylpropane sulfonic acid copolymer (P(AA-AMPS)). The presence of –NH₃⁺ species detected by X-ray photoelectron spectroscopy (XPS) revealed that an ionic cross-linked interpenetrating polymer network (IPN) was formed between the two polyelectrolyte polymers. Methanol permeability and proton conductivity were measured and compared with the Nafion^®117 membrane. The dual function of P(AA-AMPS) as both an ionic crosslinker and a proton conductor led to not only a notable reduction in methanol permeability but also an increase in proton conductivity. The CS/P(AA-AMPS) membrane with a P(AA-AMPS) content of 41 wt.% exhibited a methanol permeability (P) of 2.41 × 10⁻⁷ cm² s⁻¹ which was fifteen times lower than that of the Nafion^®117 membrane, whereas its proton conductivity (σ) was comparatively high (3.59 × 10⁻² S cm⁻¹). In terms of the overall selectivity index (β = σ/P), the PEC membrane showed a remarkably higher selectivity than the Nafion^®117 membrane, and, furthermore, the overall selectivity index increased with the increase of P(AA-AMPS) content. The mechanism of proton transfer was tentatively discussed based on the activation energy of conductivity.     

Electrochemical investigation of sulfonated poly(ether ether ketone)/clay nanocomposite membranes for moderate temperature fuel cell applications

In the present study, polyelectrolyte membranes based on partially sulfonated poly(ether ether ketone) (sPEEK) with various degrees of sulfonation are prepared. The optimum degree of sulfonation is determined according to the transport properties and hydrolytic stability of the membranes. Subsequently, various amounts of the organically modified montmorillonite (MMT) are introduced into the sPEEK matrices via the solution intercalation technique. The proton conductivity and methanol permeability measurements of the fabricated composite membranes reveal a high proton to methanol selectivity, even at elevated temperatures. Membrane based on sPEEK and 1 wt% of MMT, as the optimum nanoclay composition, exhibits a high selectivity and power density at the concentrated methanol feed. Moreover, it is found that the optimum nanocomposite membrane not only provides higher performance compared to the neat sPEEK and Nafion^®117 membranes, but also exhibits a high open circuit voltage (OCV) at the elevated methanol concentration. Owing to the high proton conductivity, reduced methanol permeability, high power density, convenient processability and low cost, sPEEK/MMT nanocomposite membranes could be considered as the alternative membranes for moderate temperature direct methanol fuel cell applications.     

Proton conducting membranes prepared by incorporation of organophosphorus acids into alcohol barrier polymers for direct methanol fuel cells

A novel type of DMFC membrane was developed via incorporation of organophosphorus acids (OPAs) into alcohol barrier materials (polyvinyl alcohol/chitosan, PVA/CS) to simultaneously acquire high proton conductivity and low methanol permeability. Three kinds of OPAs including amino trimethylene phosphonic acid (ATMP), ethylene diamine tetra(methylene phosphonic acid) (EDTMP) and hexamethylene diamine tetra(methylene phosphonic acid) (HDTMP), with different molecular structure and phosphonic acid groups content were added into PVA/CS blends and served the dual functions as proton conductor as well as crosslinker. The as-prepared OPA-doped PVA/CS membranes exhibited remarkably enhanced proton conducting ability, 2–4 times higher than that of the pristine PVA/CS membrane, comparable with that for Nafion^®117 membrane (5.04 × 10⁻² S cm⁻¹). The highest proton conductivities 3.58 × 10⁻², 3.51 × 10⁻² and 2.61 × 10⁻² S cm⁻¹ for ATMP-, EDTMP- and HDTMP-doped membranes, respectively were all achieved at highest initial OPA doping content (23.1 wt.%) at room temperature. The EDTMP-doped PVA/CS membrane with an acid content of 13.9 wt.% showed the lowest methanol permeability of 2.32 × 10⁻⁷ cm² s⁻¹ which was 16 times lower than that of Nafion^®117 membrane. In addition, the thermal stability and oxidative durability were both significantly improved by the incorporation of OPAs in comparison with pristine PVA/CS membranes.     

Effects and properties of various molecular weights of poly(propylene oxide) oligomers/Nafion acid–base blend membranes for direct methanol fuel cells

Various molecular weights of poly(propylene oxide) diamines oligomers/Nafion^® acid–base blend membranes were prepared to improve the performance of Nafion^® membranes in direct methanol fuel cells (DMFCs). The acid–base interactions were studied by Fourier transform infrared spectroscopy (FT-IR) and differential scanning calorimetry (DSC). The performance of the blend membranes was evaluated in terms of methanol permeability, proton conductivity and cell performance. The proton conductivity was slightly reduced by acid–base interaction. The methanol permeability of the blend D2000/Nafion^® was 8.61 × 10⁻⁷ cm² S⁻¹, which was reduced 60% compared to that of pristine Nafion^®. The cell performance of D2000/Nafion^® blend membranes was enhanced significantly compared to pristine Nafion^®. The current densities that were measured with Nafion^® and 3.5 wt% D2000/Nafion^® blend membranes were 62.5 and 103.5 mA cm⁻², respectively, at a potential of 0.2 V. Consequently, the blend poly(propylene oxide) diamines oligomers/Nafion^® membranes critically improved the single-cell performance of DMFC.     

Sulfonated poly(ether ether ketone)/polybenzimidazole oligomer/epoxy resin composite membranes in situ polymerization for direct methanol fuel cell usages

A diamine-terminated polybenzimidazole oligomer (o-PBI) has been synthesized for introducing the benzimidazole groups (BI) into sulfonated poly(ether ether ketone) (SPEEK) membranes. SPEEK/o-PBI/4,4′-diglycidyl(3,3′,5,5′-tetramethylbiphenyl) epoxy resin (TMBP) composite membranes in situ polymerization has been prepared for the purpose of improving the performance of SPEEK with high ion-exchange capacities (IEC) for the usage in the direct methanol fuel cells (DMFCs). The composite membranes with three-dimensional network structure are obtained through a cross-linking reaction between PBI oligomer and TMBP and the acid-base interaction between sulfonic acid groups and benzimidazole groups. Resulting membranes show a significantly increasing of all of the properties, such as high proton conductivity (0.14 S cm⁻¹ at 80 °C), low methanol permeability (2.38 × 10⁻⁸ cm² s⁻¹), low water uptake (25.66% at 80 °C) and swelling ratio (4.11% at 80 °C), strong thermal and oxidative stability, and mechanical properties. Higher selectivity has been found for the composite membranes in comparison with SPEEK. Therefore, the SPEEK/o-PBI/TMBP composite membranes show a good potential in DMFCs usages.