La1−xSrxCoO3 (x = 0.1-0.5) as the cathode catalyst for a direct borohydride fuel cell

Direct borohydride fuel cells (DBFCs), with a series of perovskite-type oxides La_1−xSr_xCoO₃ (x = 0.1-0.5) as the cathode catalysts and a hydrogen storage alloy as the anode catalyst, are studied in this paper. The structures of the perovskite-type catalysts are mainly La_1−xSr_xCoO₃ (_x = 0.1-0.5) oxides phases. However, with the increase of strontium content, the intensities of the X-ray diffraction peaks of the impure phases La₂Sr₂O₅ and SrLaCoO₄ are gradually enhanced. Without using any precious metals or expensive ion exchange membranes, a maximum current density of 275 mA cm⁻² and a power density of 109 mW cm⁻² are obtained with the Sr content of x = 0.2 at 60 °C for this novel type of fuel cell.     

Preparation and electrochemical properties of a Sm2−xSrxNiO4 cathode for an IT-SOFC

Cathodic materials Sm_2−xSr_xNiO₄ (0.5 ≤ x ≤ 1.0) for an IT-SOFC (intermediate temperature solid oxide fuel cell) were prepared by the glycine-nitrate process and characterized by XRD, SEM, ac impedance spectroscopy and dc polarization measurements. The results showed that no reaction occurred between the Sm_2−xSr_xNiO₄ electrode and the Ce_0.9Gd_0.1O_1.9 (CGO) electrolyte at 1100 °C, and the electrode formed good contact with the electrolyte after sintering at 1000 °C for 2 h. The electrochemical properties of these cathode materials were studied using impedance spectroscopy at various temperatures and oxygen partial pressures. Sm_1.0Sr_1.0NiO₄ exhibited the lowest cathodic overpotential. The area specific resistance (ASR) was 3.06 Ω cm² at 700 °C in air.     

Electrocatalytic activity of perovskite La1−xSrxMnO3 towards hydrogen peroxide reduction in alkaline medium

Perovskite-type series of compounds La_1−xSr_xMnO₃ are synthesized by a sol-gel method using Chitosan as the gelling agent. Their catalytic activity for hydrogen peroxide electroreduction in 3.0 mol dm⁻³ KOH at room temperature is evaluated by means of cyclic voltammetry and chronoamperometry. Effects of annealing temperature and the ratio of La to Sr of La_1−xSr_xMnO₃ on their catalytic performance are investigated. Among this series of compounds, La_0.4Sr_0.6MnO₃ calcined at 650 °C exhibits the highest activity, which is comparable with Co₃O₄. An aluminum-hydrogen peroxide semi-fuel cell using La_0.4Sr_0.6MnO₃ as cathode catalyst achieves a peak power density of 170 mW cm⁻² at 170 mA cm⁻² and 1.0 V running on 0.6 mol dm⁻³ H₂O₂.     

Preparation and characterization of Pr1−xSrxFeO3 cathode material for intermediate temperature solid oxide fuel cells

A kind of cathode material of Pr_1−xSr_x FeO₃ (x = 0–0.5) for intermediate temperature solid oxide fuel cells (IT-SOFCs) was prepared by the coprecipitation method. Crystal structure, thermal expansion, electrical conductivity and electrochemical performance of the Pr_1−xSr_xFeO₃ perovskite oxide cathodes were studied by different methods. The results revealed that Pr_l−xSr_xFeO₃ exhibited similar orthorhombic structure from x = 0.1 to 0.3 and took cubic structure when x = 0.4–0.5. The unit cell volume decreased and the thermal expansion coefficient (TEC) of the materials increased as the strontium content increased. When 0 < x ≤ 0.3, the samples exhibited good thermal expansion compatibility with YSZ electrolyte. The electrical conductivity increased with the increasing of doped strontium content. When x = 0.3–0.5, the electrical conductivities were higher than 100 S cm⁻¹. The conductivity of Pr_0.8Sr_0.2FeO₃ was 78 S cm⁻¹ at 800 °C. Compared with the La_0.8Sr_0.2MnO₃ cathode, Pr_0.8Sr_0.2FeO₃ showed higher polarization current density and lower polarization resistance (0.2038 Ω cm²). The value of I₀ for Pr_0.8Sr_0.2FeO₃ at 800 °C is 123.6 mA cm⁻². It is higher than that of La_0.8Sr_0.2MnO₃. Therefore, Pr_1−xSr_xFeO₃ can be considered as a candidate cathode material for IT-SOFCs.     

Low-temperature solid oxide fuel cells with La1−xSrxMnO3 as the cathodes

La_1−xSr_xMnO₃ (LSM) has been widely developed as the cathode material for high-temperature solid oxide fuel cells (SOFCs) due to its chemical and mechanical compatibilities with the electrolyte materials. However, its application to low-temperature SOFCs is limited since its electrochemical activity decreases substantially when the temperature is reduced. In this work, low-temperature SOFCs based on LSM cathodes are developed by coating nanoscale samaria-doped ceria (SDC) onto the porous electrodes to significantly increase the electrode activity of both cathodes and anodes. A peak power density of 0.46 W cm⁻² and area specific interfacial polarization resistance of 0.36 Ω cm² are achieved at 600 °C for single cells consisting of Ni-SDC anodes, LSM cathodes, and SDC electrolytes. The cell performances are comparable with those obtained with cobalt-based cathodes such as Sm_0.5Sr_0.5CoO₃, and therefore encouraging in the development of low-temperature SOFCs with high reliability and durability.     

Characterization of La2−xSrxCoTiO6 (0.6 ≤ x ≤ 1.0) series as new cathodes of solid oxide fuel cells

La_2−xSr_xCoTiO₆ (0.6 ≤ x ≤ 1.0) compound series is prepared by Sr-substitution in the A-site of the perovskite by a modified Pechini procedure under air. Charge compensation as Sr²⁺ content increase occurs by Co²⁺ oxidation to Co³⁺. Reduced samples are obtained by further treatment under 5%H₂/Ar and characterized by Neutron Powder Diffraction. Upon redution, Co³⁺ to Co²⁺ reduction and oxygen vacancies creation are detected. Dependence of total conductivity with temperature and pO₂ exhibits a typical p-type semiconducting behaviour. Results show that the higher the Sr content, the higher holes (Co³⁺) concentration and consequently, La_2−xSr_xCoTiO₆ (x = 1.0) shows the highest conductivity (13.23 S/cm at 1073 K in air). The negligible reactivity with YSZ, used as the electrolyte, of symmetrical cells under oxidant conditions and the moderate thermal expansion found by XRD point to their possible use as SOFC cathodes. Thus, La_1.2Sr_0.8CoTiO₆-based cathodes display polarization resistance of 0.9 Ω cm² at 1073 K in oxygen, only slightly above than the current state-of-the-art.     

Structural and electrochemical characterization of xLi[Li1/3Mn2/3]O2·(1 − x)Li[Ni1/3Mn1/3Co1/3]O2 (0 ≤ x ≤ 0.9) as cathode materials for lithium ion batteries

A series of cathode materials with molecular notation of xLi[Li_1/3Mn_2/3]O₂·(1 − x)Li[Ni_1/3Mn_1/3Co_1/3]O₂ (0 ≤ x ≤ 0.9) were synthesized by combination of co-precipitation and solid state calcination method. The prepared materials were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques, and their electrochemical performances were investigated. The results showed that sample 0.6Li[Li_1/3Mn_2/3]O₂·0.4Li[Ni_1/3Mn_1/3Co_1/3]O₂ (x = 0.6) delivers the highest capacity and shows good capacity-retention, which delivers a capacity ∼250 mAh g⁻¹ between 2.0 and 4.8 V at 18 mA g⁻¹.     

The influence of compositional change of 0.3Li2MnO3·0.7LiMn1−xNiyCo0.1O2 (0.2 ≤ x ≤ 0.5, y = x − 0.1) cathode materials prepared by co-precipitation

Cathode materials prepared by a co-precipitation are 0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (0.2 ≤ x ≤ 0.4) cathode materials with a layered-spinel structure. In the voltage range of 2.0-4.6 V, the cathodes show more than one redox reaction peak during its cyclic voltammogram. The Li/0.3Li₂MnO₃·0.7LiMn_1−xNi_yCo_0.1O₂ (x = 0.3, y = 0.2) cell shows the initial discharge capacity of about 200 mAh g⁻¹. However, when x = 0.2 and y = 0.1, the cell exhibits a rapid decrease in discharge capacity and poor cycle life.     

Preparation and electrochemical properties of Sr-doped Nd2NiO4 cathode materials for intermediate-temperature solid oxide fuel cells

Cathode materials Nd_2 − xSr_xNiO₄ were prepared by the glycine-nitrate process and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), AC impendence spectroscopy and DC polarization method, respectively. The results show that no reaction occurred between the electrode and the CGO electrolyte at 1100 °C and the electrode formed good contact with the electrolyte after being sintered at 1000 °C for 4 h. The rate-limiting step for oxygen reduction reaction on Nd_1.6Sr_0.4NiO₄ electrode changed with oxygen partial pressure and measurement temperature. The Nd_1.6Sr_0.4NiO₄ electrode gave a polarization resistance of 0.93 Ω cm² at 700 °C in air, which indicates that Nd_2 − xSr_xNiO₄ electrode is a promising cathode material for intermediate-temperature solid oxide fuel cell (IT-SOFC).     

Sm0.2(Ce1−xTix)0.8O1.9 modified Ni-yttria-stabilized zirconia anode for direct methane fuel cell

Sm_0.2(Ce_1−xTi_x)_0.8O_1.9 (SCTx, x = 0-0.29) modified Ni-yttria-stabilized zirconia (YSZ) has been fabricated and evaluated as anode in solid oxide fuel cells for direct utilization of methane fuel. It has been found that both the amount of Ti-doping and the SCTx loading level in the anode have substantial effect on the electrochemical activity for methane oxidation. Optimal anode performance for methane oxidation has been obtained for Sm_0.2(Ce_0.83Ti_0.17)_0.8O_1.9 (SCT0.17) modified Ni-YSZ anode with SCT0.17 loading of about 241 mg cm⁻² resulted from four repeated impregnation cycles. When operating on humidified methane as fuel and ambient air as oxidant at 700 °C, single cells with the configuration of SCT0.17 modified Ni-YSZ anode, YSZ electrolyte and La_0.6Sr_0.4Co_0.2Fe_0.8O₃-Sm_0.2Ce_0.8O_1.9 (LSCF-SDC) composite cathode show the polarization cell resistance of 0.63 Ω cm² under open circuit conditions and produce a peak power density of 383 mW cm⁻². It has been revealed that the coated Ti-doped SDC on Ni-YSZ anode not only effectively prevents the methane fuel from directly impacting on the Ni particles, but also enhances the kinetics of methane oxidation due to an improved oxygen storage capacity (OSC) and redox equilibrium of the anode surface, resulting in significant enhancement of the SCTx modified Ni-YSZ anode for direct methane oxidation.     

Synthesis and performance of Sr1.5LaxMnO4 as cathode materials for intermediate temperature solid oxide fuel cell

A-site non-stoichiometric materials Sr_1.5La_xMnO₄ (x = 0.35, 0.40, 0.45) are prepared via solid state reaction. The structure of these materials is determined to be tetragonal. Both the lattice volume and the thermal expansion coefficient reduce with the decrease of lanthanum content. On the contrary, the conductivity increases and the maximum value of 13.9 S cm⁻¹ is found for Sr_1.5La_0.35MnO₄ at 750 °C in air. AC impedance spectroscopy and DC polarization measurements are used to study the electrode performance. The optimum composition of Sr_1.5La_0.35MnO₄ results in 0.25 Ω cm² area specific resistance (ASR) at 750 °C in air. The oxygen partial pressure measurement indicates that the charge transfer process is the rate-limiting step of the electrode reactions.     

Pseudocapacitive properties of electrochemically prepared nickel oxides on 3-dimensional carbon nanotube film substrates

Nickel oxides on carbon nanotube electrodes (NiO_x/CNT electrodes) are prepared by depositing Ni(OH)₂ electrochemically onto carbon nanotube (CNT) film substrates with subsequent heating to 300 °C. Compared with the as deposited Ni(OH)₂ on CNT film substrates (Ni(OH)₂/CNT electrodes), the 300 °C heat treated electrode shows much high rate capability, which makes it suitable as an electrode in supercapacitor applications. X-ray photoelectron spectroscopy shows that the pseudocapacitance of the NiO_x/CNT electrodes in a 1 M KOH solution originates from redox reactions of NiO_x/NiO_xOH and Ni(OH)₂/NiOOH. The 8.9 wt.% NiO_x in the NiO_x/CNT electrode shows a NiO_x-normalized specific capacitance of 1701 F g⁻¹ with excellent high rate capability due to the 3-dimensional nanoporous network structure with an extremely thin NiO_x layer on the CNT film substrate. On the other hand, the 36.6 wt.% NiO_x/CNT electrode has a maximum geometric and volumetric capacitance of 127 mF cm⁻² and 254 F cc⁻¹, respectively, with a specific capacitance of 671 F g⁻¹, which is much lower than that of the 8.9% NiO_x electrode. This decrease in specific capacitance of the high wt.% NiO_x/CNT electrodes can be attributed to the dead volume of the oxides, high equivalent series resistance for a heavier deposit, and the ineffective ionic transportation caused by the destruction of the 3-dimensional network structure. Deconvolution analysis of the cyclic voltammograms reveals that the rate capability of the NiO_x/CNT electrodes is adversely affected by the redox reaction of Ni(OH)₂, while the adverse effects from the reaction of NiO_x is insignificant.     

Electrochemical behavior of Li3−xM′xV2−yM″y(PO4)3 (M′ = K, M″ = Sc, Mg + Ti)/C composite cathode material for lithium-ion batteries

Composites of monoclinic Li_3−xM′_xV_2−yM″_2y(PO₄)₃ (M′ = K, M″ = Sc, Mg + Ti) with carbon were synthesized by solid-state reaction using oxalic acid or 6% H₂/Ar gas mixture as reducing agents at sintering temperature of 850 °C. The samples were characterized by X-ray diffraction (XRD), voltammetry and electrochemical galvanostatic cycling. The capacity of Li₃V₂(PO₄)₃ synthesized using hydrogen as the reducing agent was 127 mA h g⁻¹ and decreased to 120 mA h g⁻¹ after 20 charge-discharge cycles. The substitution of lithium and vanadium for other ions did not result in the improvement of the electrochemical characteristics of the samples.     

Double-perovskites YBaCo2−xFexO5+δ cathodes for intermediate-temperature solid oxide fuel cells

Double-perovskites YBaCo_2−xFe_xO_5+δ (YBCF, x = 0.0, 0.2, 0.4 and 0.6) are synthesized with a solid-state reaction and are assessed as potential cathode materials for utilization in intermediate-temperature solid oxide fuel cells (IT-SOFCs) on the La_0.9Sr_0.1Ga_0.8Mg_0.115Co_0.085O_2.85 (LSGMC) electrolyte. The YBCF materials exhibit chemical compatibility with the LSGMC electrolyte up to a temperature of 950 °C. The conductivity of the YBCF samples decreases with increasing Fe content, and the maximum conductivity of YBCF is 315 S cm⁻¹ at 325 °C for the x = 0.0 sample. A semiconductor-metal transition is observed at about 300-400 °C. The thermal expansion coefficient of the YBCF samples increases from 16.3 to 18.0 × 10⁻⁶ K⁻¹ in air at temperatures between 30 and 900 °C with increase in Fe content. The area-specific resistances of YBCF cathodes at x = 0.0, 0.2 and 0.4 on the LSGMC electrolyte are 0.11, 0.13 and 0.15 Ω cm² at a temperature of 700 °C, respectively. The maximum power densities of the single cells fabricated with the LSGMC electrolyte, Ce_0.8Sm_0.2O_1.9 (SDC) interlayer, NiO/SDC anode and YBCF cathodes at x = 0.0, 0.2 and 0.4 reach 873, 768 and 706 mW cm⁻², respectively. This study suggests that the double-perovskites YBCF (0 ≤ x ≤ 0.4) can be potential candidates for utilization as IT-SOFC cathodes.     

Comparative study of oxygen reduction reaction on RuxMySez (M = Cr, Mo, W) electrocatalysts for polymer exchange membrane fuel cell

Electrochemical evaluation of the Ru_xM_ySe_z (M = Cr, Mo, W) type electrocatalysts towards the oxygen reduction reaction (ORR) is presented. The electrocatalysts were synthesized by reacting the corresponding transition metal carbonyl compounds and elemental selenium in 1,6-hexanediol under refluxing conditions for 3 h. The powder electrocatalysts were characterized by scanning electron microscopy (SEM), and X-ray diffraction (XRD). Results indicate the formation of agglomerates of crystalline particles with nanometric size embedded in an amorphous phase. The particle size decreased according to the following trend: Ru_xCr_ySe_z > Ru_xW_ySe_z > Ru_xMo_ySe_z. Electrochemical studies were performed by rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) techniques. Kinetic parameters exhibited Tafel slopes of 120 mV dec⁻¹; exchange current density of around 1 × 10⁻⁵ mA cm⁻² and apparent activation energies between 40 and 55 kJ mol⁻¹. A four-electron reduction was found in all three cases. The catalytic activity towards the ORR decreases according to the following trend: Ru_xMo_ySe_z > Ru_xW_ySe_z > Ru_xCr_ySe_z. However this trend was not maintained when the materials were tested as cathode electrodes in a single polymer exchange membrane fuel cell, PEMFC. The Ru_xW_ySe_z electrocatalyst showed poor activity compared to Ru_xMo_ySe_z and Ru_xCr_ySe_z which were considered suitable candidates to be used as cathode in PEMFCs.     

La substituted Sr2MnO4 as a possible cathode material in SOFC

Sr_2−xLa_xMnO_4+δ (x = 0.4, 0.5, 0.6) oxides were studied as the cathode material for solid oxide fuel cells (SOFC). The reactivity tests indicated that no reaction occurred between Sr_2−xLa_xMnO_4+δ and CGO at annealing temperature of 1000 °C, and the electrode formed good contact with the electrolyte after being sintered at 1000 °C for 4 h. The total electrical conductivity, which has strong effect on the electrode properties, was determined in a temperature range from 100 to 800 °C. The maximum value of 5.7 S cm⁻¹ was found for the x = 0.6 phase at 800 °C in air. The cathode polarization and AC impedance results showed that Sr_1.4La_0.6MnO_4+δ exhibited the lowest cathode overpotential. The area specific resistance (ASR) was 0.39 Ω cm² at 800 °C in air. The charge transfer process is the rate-limiting step for oxygen reduction reaction on Sr_1.4La_0.6MnO_4+δ electrode.     

Structural and electrochemical characterization of La2−xSrxNiTiO6−δ

Materials of the series La_2−xSr_xNiTiO_6−δ (0 ≤ x ≤ 0.5) have been characterized by both structural and electrochemical methods in order to assess their possible use as electrodes for SOFCs. Neutron and X-ray powder diffraction experiments have shown that they are stable under both oxidizing and reducing conditions while chemically compatible with YSZ at SOFC operating temperatures. Moreover, the thermal expansion has been determined to be isotropic with α_L = 10.0(3) × 10⁻⁶ K⁻¹. This value is similar to that found for other perovskite materials used in SOFCs. However, polarization resistances reveal modest values of electrochemical response under oxygen (1.5 Ω cm² at 900 °C) and are quite poor in 5%H₂/N₂ mixtures (15 Ω cm²) at the same temperature. Nevertheless, microstructure has not been optimized fully enough to discard the material as a potential SOFC cathode.     

2LiH + M (M = Mg, Ti): New concept of negative electrode for rechargeable lithium-ion batteries

xLiH + M composites, where M = Mg or Ti, are suggested as new candidates for negative electrode for Li-ion batteries. For this purpose, the xLiH + M electrode is prepared using the mechanochemical reaction: MH_x + xLi → xLiH + M or by simply grinding a xLiH + M mixture. The most promising electrochemical behaviour is obtained with the (2LiH + Mg) composite prepared via a mechanochemical reaction between MgH₂ and metallic Li leading to a very divided composite in which Mg crystallites of 20 nm size are embedded in a LiH matrix. Reversible capacities of 1064 mAh g⁻¹ (three times as much as the one of graphite) and 600 mAh g⁻¹ are reached for these phase mixtures after 1 and 28 h of grinding in vertical and planetary mill, respectively. The (2LiH + Ti) mixture prepared via the mechanochemical reaction between TiH₂ and Li exhibits a reversible capacity of 428 mAh g⁻¹. From X-ray diffraction measurements, the performances of the electrodes are attributed to the electrochemical conversion reaction: M + xLiH ↔ MH_x + xLi⁺ + xe⁻ (M = Mg, Ti) followed for M = Mg by an alloying process where M reacts with lithium ions to form Mg_1−xLi_x alloys.     

Bulk conduction and relaxation in [(ZrO2)1−x(CeO2)x]0.92(Y2O3)0.08 (0 ≤ x ≤ 1) solid solutions at intermediate temperatures

Bulk conduction and relaxation of the [(ZrO₂)_1−x(CeO₂)_x]_0.92(Y₂O₃)_0.08 (0 ≤ x ≤ 1) solid solutions were studied using impedance spectroscopy at intermediate temperatures (200-500 °C). The bulk conductivity as a function of x shows a “V-shape” variation which is a competitive effect of the defect associates and the lattice parameter. In the ZrO₂-rich region (x < 0.5) CeO₂ doping increases the concentration of defect associates which limits the mobility of the oxygen vacancies; in the CeO₂-rich region (x > 0.5) the increase of x increases the lattice parameter which enlarges the free channel for oxygen vacancy migration. Further analysis indicates the ionic radius of the tetravalent dopant determines the composition dependence of the ionic conductivity of the solid solutions. When doping YSZ with other tetravalent dopant with similar ionic radius with Zr⁴⁺, e.g., Hf⁴⁺, such “V-shape” composition dependence of the bulk conductivity cannot be observed.     

Assessment of perovskite-type La0.8Sr0.2ScxMn1−xO3-δ oxides as anodes for intermediate-temperature solid oxide fuel cells using hydrocarbon fuels

Composites formed by the infiltration of 40 wt% La_0.8Sr_0.2Sc_xMn_1−xO_3-δ (LSSM) oxides (x = 0.1, 0.2, 0.3) into 65% porous yttria-stabilized zirconia (YSZ) are investigated as anode materials for intermediate-temperature solid oxide fuel cells for hydrocarbon oxidation. The oxygen non-stoichiometry and electrical conductivity of each LSSM-YSZ composite are determined by coulometric titration. As the concentration of Sc increases, the composites show higher phase stability and the electrical conductivity of LSSM is significantly affected by the Sc doping, the non-stoichiometric oxygen content, and oxygen partial pressure (p(O₂)). To achieve better electrochemical performance, it is necessary to add ceria-supported palladium catalyst for operation with humidified CH₄. Anode polarization resistance increases with Sc doping due to a decrease in electrical conductivity. An electrolyte-supported cell with a LSSM-YSZ composite anode delivers peak power densities of 395 and 340 mW cm⁻² at 923 K in humidified (3% H₂O) H₂ and CH₄, respectively, at a flow rate of 20 mL min⁻¹.