A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Synthesis and characterization of Carbon Nano Fiber/LiFePO4 composites for Li-ion batteries

Carbon Nano Fibers (CNFs) coated with LiFePO₄ particles have been prepared by a non-aqueous sol–gel technique. The functionalization of the CNFs by HNO₃ acid treatment has been confirmed by Raman and XPS analyses. The samples pure LiFePO₄ and LiFePO₄–CNF have been characterized by XRD, SEM, RAMAN, XPS and electrochemical analysis. The LiFePO₄–CNF sample shows better electrochemical performance compared to as-prepared LiFePO₄. LiFePO₄–CNF (10 wt.%) delivers a higher specific capacity (∼140 mAh g⁻¹) than LiFePO₄ with carbon black (25 wt.%) added after synthesis (∼120 mAh g⁻¹) at 0.1C.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

Novel polymer electrolytes based on triblock poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) with ionically active SiO2

A novel polymer electrolyte based on triblock copolymer of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) with ionically active SiO₂ inclusions has been designed. The electrolyte shows favorable features for ion migration such as low glass transition temperature and high concentration of amorphous phase. Combined with the effect of active SiO₂, its ionic conductivity is about 8.0 × 10⁻⁵ S cm⁻¹ at 30 °C, which exceeds that for the PEO-based systems. As applying them to cells with LiFePO₄-type cathodes, a capacity of about 147.0 mAh g⁻¹ is obtained at 60 °C, which is retained by more than 90% after 40 charge/discharge cycles. Moreover, about 100 mAh g⁻¹ could still be delivered as temperature decreases to 30 °C.     

Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

Improved high-rate charge/discharge performances of LiFePO4/C via V-doping

V-doped LiFePO₄/C cathode materials were prepared through a carbothermal reduction route. The microstructure was characterized by X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. The electrochemical Li⁺ intercalation performances of V-doped LiFePO₄/C were compared with those of undoped one through galvanostatic intermittent titration technique, cyclic voltamperometry, and electrochemical impedance spectrum. V-doped LiFePO₄/C showed a high discharge capacity of ∼70 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. The significantly improved high-rate charge/discharge capacity is attributed to the increase of Li⁺ ion “effective” diffusion capability.     

Cathode performance of olivine-type LiFePO4 synthesized by chemical lithiation

Chemical lithiation with LiI in acetonitrile was performed for amorphous FePO₄ synthesized from an equimolar aqueous suspension of iron powder and an aqueous solution of P₂O₅. An orthorhombic LiFePO₄ olivine structure was obtained by annealing a chemically lithiated sample at 550 °C for 5 h in Ar atmosphere. The average particle size remained at approximately 250 nm even after annealing. The lithium content in the sample was quantitatively confirmed by Li atomic absorption analysis and ⁵⁷Fe Mössbauer spectroscopy. While an amorphous FePO₄/carbon composite cathode has a monotonously decreasing charge–discharge profile with a reversible capacity of more than 140 mAh g⁻¹, the crystallized LiFePO₄/carbon composite shows a 3.4 V plateau corresponding to a two-phase reaction. This means that the lithium in the chemically lithiated sample is electrochemically active. Both amorphous FePO₄ and the chemically lithiated and annealed crystalline LiFePO₄ cathode materials showed good cyclability (more than 140 mAh g⁻¹ at the 40th cycle) and good discharge rate capability (more than 100 mAh g⁻¹ at 5.0 mA cm⁻²). In addition, the fast-charge performance was found to be comparable to that with LiCoO₂.     

Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.     

Hydrothermal preparation of LiFePO4 nanocrystals mediated by organic acid

Well-crystallized LiFePO₄ nanoparticles have been directly synthesized in a short time via hydrothermal process in the presence of organic acid, e.g. citric acid or ascorbic acid. These acid-mediated LiFePO₄ products exhibit a phase-pure and nanocrystal nature with size about 50-100 nm. Two critical roles that the organic acid mediator plays in hydrothermal process are recognized and a rational mechanism is explored. After a post carbon-coating treatment at 600 °C for 1 h, these mediated LiFePO₄ materials show a high electrochemical activity in terms of reversible capacity, cycling stability and rate capability. Particularly, LiFePO₄ mediated by ascorbic acid can deliver a capacity of 162 mAh g⁻¹ at 0.1 C, 154 mAh g⁻¹ at 1 C, and 122 mAh g⁻¹ at 5 C. The crystalline structure, particle morphology, and surface microstructure were characterized by high-energy synchrotron X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), and Raman spectroscopy, respectively. And the electrochemical properties were thoroughly investigated by galvanostatic test and electrochemical impedance spectroscopy (EIS).     

Optimized performances of core-shell structured LiFePO4/C nanocomposite

A nanosized LiFePO₄/C composite with a complete and thin carbon-shell is synthesized via a ball-milling route followed by solid-state reaction using poly(vinvl alcohol) as carbon source. The LiFePO₄/C nanocomposite delivers discharge capacities of 159, 141, 124 and 112 mAh g⁻¹ at 1 C, 5 C, 15 C and 20 C, respectively. Even at a charge-discharge rate of 30 C, there is still a high discharge capacity of 107 mAh g⁻¹ and almost no capacity fading after 1000 cycles. Based on the analysis of cyclic voltammograms, the apparent diffusion coefficients of Li ions in the composite are in the region of 2.42 × 10⁻¹¹ cm² s⁻¹ and 2.80 × 10⁻¹¹ cm² s⁻¹. Electrochemical impedance spectroscopy and galvanostatic intermittent titration technique are also used to calculate the diffusion coefficients of Li ions in the LiFePO₄/C electrode, they are in the range of 10⁻¹¹-10⁻¹⁴ cm² s⁻¹. In addition, at −20 °C, it can still deliver a discharge capacity of 122 mAh g⁻¹, 90 mAh g⁻¹ and 80 mAh g⁻¹ at the charge-discharge rates of 0.1 C, 0.5 C and 1 C, respectively.     

High reversible capacities of graphite and SiO/graphite with solvent-free solid polymer electrolyte for lithium-ion batteries

The combination of graphite or silicon monoxide (SiO)/graphite = 1/1 mixture with a solvent-free solid polymer electrolyte (SPE) was fabricated using a new preparation process, involving precoating the electrode with vapor-grown carbon fiber (VGCF) and binders (polyvinyl difluoride: PVdF or polyimide: PI), followed by the overcoating of the SPE. The reversible capacity of [graphite | SPE | Li] and [SiO/graphite | SPE | Li] cells were >360 and >1000 mAh g⁻¹ with 78% and 77% for the 1st Coulombic efficiency, respectively. The reversible capacities were 75% at the 250th cycle for [graphite | SPE | Li] and 72% at the 100th cycle for [SiO/graphite | SPE | Li]. The electrode used was compatible with that of the conventional liquid electrolyte system, and the SPE film could be formed on the electrode by the continuous overcoating process, which will lead to a low-cost electrodes and low-cost battery production. The solid-state lithium-ion polymer battery (SSLiPB) developed in this study, which consisted of [LiFePO₄ | SPE | graphite], showed the reversible capacity of 128 mAh g⁻¹ (based on the LiFePO₄ capacity) with favorable cycle performance.     

New freeze-drying method for LiFePO4 synthesis

The freeze-drying method is proposed as an effective synthesis process for the obtaining of LiFePO₄/C composites. The citric acid is used as a complexing agent and carbon source. After the low temperature annealing, the freeze-dried solution leads to a homogeneous carbon covered LiFePO₄ sample. The chemical characterization of the material included ICP and elemental analysis, infrared spectroscopy, X-ray diffraction, magnetic measurements and thermal analysis. SEM and TEM microscopies indicate an aggregate morphology with tiny particles of lithium iron phosphate inside a carbon matrix. Impedance spectroscopy showed a 8.0 × 10⁻⁷ S cm⁻¹ conductivity value. Cyclic voltammetry graphics displayed the two peaks corresponding to the Fe(II)/Fe(III) reaction and demonstrated the good reversibility of the material. The specific capacity value obtained at C/40 rate was 164 mAh g⁻¹, with a slight decrease on greater C-rates reaching 146 mAh g⁻¹ at C/1. The capacity retention study has evidenced good properties, with retention over 97% of the maximum values in the first 50 cycles, which allows an effective performance of the freeze-dried sample as cathodic material in lithium-ion batteries.     

Electrochemical properties of cross-linked polymer electrolyte by electron beam irradiation and application to lithium ion batteries

A polymer electrolyte was successfully fabricated for a room temperature operation lithium battery by cross-linking the mixture of oligomeric poly (ethylene glycol) dimethylether (PEGDME) and poly (ethylene glycol) diacrylate (PEGDA) with Li(CF₃SO₂)₂N using electron beam irradiation. The maximum ionic conductivity achieved for the cross-linked solid polymer electrolyte (c-SPE) at room temperature was 2.1 × 10⁻⁴ S cm⁻¹ and the lithium transport number of the electrolyte was around 0.2. The c-SPE showed no reaction heat with lithium metal up to 300 °C. The interface resistance of Li/c-SPE/Li at room temperature was about 45 Ω cm², which is considerable lower than that of 210 Ω cm² for Li/PEO₁₀Li(CF₃SO₂)₂N/Li. The electrochemical window of the polymer electrolyte was above 4 V (versus Li⁺/Li). The initial discharge capacity for the Li/SPE/LiFePO₄-C cell was approximately 90 mAh g⁻¹ for LiFePO₄-C at 1/10 °C rate at room temperature and showed a good cyclability and a high coulombic efficiency of 99.2%.     

Effects of roasting temperature and modification on properties of Li2FeSiO4/C cathode

Li₂FeSiO₄/C cathodes were synthesized by combination of wet-process method and solid-state reaction at high temperature, and effects of roasting temperature and modification on properties of the Li₂FeSiO₄/C cathode were investigated. The XRD patterns of the Li₂FeSiO₄/C samples indicate that all the samples are of good crystallinity, and a little Fe₃O₄ impurity was observed in them. The primary particle size rises as the roasting temperature increases from 600 to 750 °C. The Li₂FeSiO₄/C sample synthesized at 650 °C has good electrochemical performances with an initial discharge capacity of 144.9 mAh g⁻¹ and the discharge capacity remains 136.5 mAh g⁻¹ after 10 cycles. The performance of Li₂FeSiO₄/C cathode is further improved by modification of Ni substitution. The Li₂Fe_0.9Ni_0.1SiO₄/C composite cathode has an initial discharge capacity of 160.1 mAh g⁻¹, and the discharge capacity remains 153.9 mAh g⁻¹ after 10 cycles. The diffusion coefficient of lithium in Li₂FeSiO₄/C is 1.38 × 10⁻¹² cm² s⁻¹ while that in Li₂Fe_0.9Ni_0.1SiO₄/C reaches 3.34 × 10⁻¹² cm² s⁻¹.     

Porous micro-spherical aggregates of LiFePO4/C nanocomposites: A novel and simple template-free concept and synthesis via sol-gel-spray drying method

Porous micro-spherical aggregates of LiFePO₄/C nanocomposites were prepared with a process of spray drying at 200 °C and subsequent heat treatment at 700 °C for 12 h by a novel and simple template-free sol-gel-SD method independent of surfactants or templates. The results indicate that the as-obtained LiFePO₄ porous microspheres have the mean diameter of 19.8 μm, average pore size of 45 nm, and large specific surface area (20.2 m² g⁻¹) with evenly distributed carbon (4.5 wt.%). The particles can be easily brought into contact with electrolyte, facilitating electric and lithium ion diffusion. They present large reversible discharge capacity of 137.5 mAh g⁻¹ at the current density of 0.1 C, good rate capacity of 53.8 mAh g⁻¹ at 10 C, and excellent capacity retention rate closed to 100% after various current densities in the region of 2.0-4.3 V.     

Electrochemical properties of LiFe0.9Mn0.1PO4/Fe2P cathode material by mechanical alloying

LiFePO₄, olivine-type LiFe_0.9Mn_0.1PO₄/Fe₂P composite was synthesized by mechanical alloying of carbon (acetylene back), M₂O₃ (M = Fe, Mn) and LiOH·H₂O for 2 h followed by a short-time firing at 900 °C for only 30 min. By varying the carbon excess different amounts of Fe₂P second phase was achieved. The short firing time prevented grain growth, improving the high-rate charge/discharge capacity. The electrochemical performance was tested at various C/x-rate. The discharge capacity at 1C rate was increased up to 120 mAh g⁻¹ for the LiFe_0.9Mn_0.1PO₄/Fe₂P composite, while that of the unsubstituted LiFePO₄/Fe₂P and LiFePO₄ showed only 110 and 60 mAh g⁻¹, respectively. Electronic conductivity and ionic diffusion constant were measured. The LiFe_0.9Mn_0.1PO₄/Fe₂P composite showed higher conductivity and the highest diffusion coefficient (3.90 × 10⁻¹⁴ cm² s⁻¹). Thus the improvement of the electrochemical performance can be attributed to (1) higher electronic conductivity by the formation of conductive Fe₂P together with (2) an increase of Li⁺ ion mobility obtained by the substitution of Mn²⁺ for Fe²⁺.     

Improved electrolytes for Li-ion batteries: Mixtures of ionic liquid and organic electrolyte with enhanced safety and electrochemical performance

Physical and electrochemical characteristics of Li-ion battery systems based on LiFePO₄ cathodes and graphite anodes with mixture electrolytes were investigated. The mixed electrolytes are based on an ionic liquid (IL), and organic solvents used in commercial batteries. We investigated a range of compositions to determine an optimum conductivity and non-flammability of the mixed electrolyte. This led us to examine mixtures of ILs with the organic electrolyte usually employed in commercial Li-ion batteries, i.e., ethylene carbonate (EC) and diethylene carbonate (DEC). The IL electrolyte consisted of (trifluoromethyl sulfonylimide) (TFSI) as anion and 1-ethyl-3-methyleimidazolium (EMI) as the cation. The physical and electrochemical properties of some of these mixtures showed an improvement characteristics compared to the constituents alone. The safety was improved with electrolyte mixtures; when IL content in the mixture is ≥40%, no flammability is observed. A stable SEI layer was obtained on the MCMB graphite anode in these mixed electrolytes, which is not obtained with IL containing the TFSI-anion. The high-rate capability of LiFePO₄ is similar in the organic electrolyte and the mixture with a composition of 1:1. The interface resistance of the LiFePO₄ cathode is stabilized when the IL is added to the electrolyte. A reversible capacity of 155 mAh g⁻¹ at C/12 is obtained with cells having at least some organic electrolyte compared to only 124 mAh g⁻¹ with pure IL. With increasing discharge rate, the capacity is maintained close to that in the organic solvent up to 2 C rate. At higher rates, the results with mixture electrolytes start to deviate from the pure organic electrolyte cell. The evaluation of the Li-ion cells; LiFePO₄//Li₄Ti₅O₁₂ with organic and, 40% mixture electrolytes showed good 1st CE at 98.7 and 93.0%, respectively. The power performance of both cell configurations is comparable up to 2 C rate. This study indicates that safety and electrochemical performance of the Li-ion battery can be improved by using mixed IL and organic solvents.     

Synthesis of LiFePO4/C composite with high-rate performance by starch sol assisted rheological phase method

LiFePO₄/C composite was synthesized at 600 °C in an Ar atmosphere by a soluble starch sol assisted rheological phase method using home-made amorphous nano-FePO₄ as the iron source. XRD, SEM and TEM observations show that the LiFePO₄/C composite has good crystallinity, ultrafine sphere-like particles of 100-200 nm size and in situ carbon. The synthesized LiFePO₄ could inherit the morphology of FePO₄ precursor. The electrochemical performance of the LiFePO₄ by galvanostatic cycling studies demonstrates excellent high-rate cycle stability. The Li/LiFePO₄ cell displays a high initial discharge capacity of more than 157 mAh g⁻¹ at 0.2C and a little discharge capacity decreases from the first to the 80th cycle (>98.3%). Remarkably, even at a high current density of 30C, the cell still presents good cycle retention.     

Morphological characterization of LiFePO4/C composite cathode materials synthesized via a carboxylic acid route

A new type of LiFePO₄/C composite surrounded by a web containing both amorphous and crystalline carbon phases was synthesized by incorporating malonic acid as a carbon source using a high temperature solid-state method. SEM, TEM/SAED/EDS and HRTEM were used to analyze surface morphology and confirmed for the first time that crystalline carbon was present in LiFePO₄/C composites. The composite was effective in enhancing the electrochemical properties such as capacity and rate capability, because its active component consists of nanometer-sized particles containing pores with a wide range of sizes. An EDS elemental map showed that carbon was uniformly distributed on the surface of the composite crystalline particles. TEM/EDS results clearly show a dark region that is LiFePO₄ with a trace of carbon and a gray region that is carbon only. To evaluate the materials’ electrochemical properties, galvanostatic cycling and conductivity measurements were performed. The best cell performance was delivered by the material coated with 60 wt.% malonic acid, which delivered first cycle discharge capacity of 149 mAh g⁻¹ at a C/5 rate and sustained 222 cycles at 80% of capacity retention. When carboxylic acid was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁵ to 10⁻⁴ S cm⁻¹, since particle growth was prevented during the final sintering process.