Porosity-graded micro-porous layers for polymer electrolyte membrane fuel cells

In this paper, the effect of porosity-graded micro-porous layer (GMPL) on the performance of polymer electrolyte membrane fuel cells (PEMFCs) was studied in detail. The GMPL was prepared by printing micro-porous layers (MPL) with different content of NH₄Cl pore-former and the porosity of the GMPL decreased from the inner layer of the MPLs at the membrane/MPL interface to the outer layer of the MPLs at the gas diffusion electrode/MPL interface. The morphology and porosity of the GMPLs were characterized and the performance of the cell with GMPLs was compared with those having conventional homogeneous MPLs. The result demonstrates that the fuel cells consisting of GMPL have better performance than those consisting of conventional homogeneous MPLs, especially at high current densities. Micro-porous layer with graded porosity is beneficial for the electrode process of fuel cell reaction probably by facilitating the liquid water transportation through large pores and gas diffusion via small pores in the GMPLs.     

A study of water transport as a function of the micro-porous layer arrangement in PEMFCs

Electrochemical losses as a function of the micro-porous layer (MPL) arrangement in Proton Exchange Membrane Fuel Cells (PEMFCs) are investigated by electrochemical impedance spectroscopy (EIS). Net water flux across the polymer membrane in PEMFCs is investigated for various arrangements of the MPL, namely with MPL on the cathode side alone, with MPL on both the cathode and the anode sides and without MPL. EIS and water transport are recorded for various operating conditions, such as the relative humidity of the hydrogen inlet and current density, in a PEMFC fed by fully-saturated air. The cell with an MPL on the cathode side alone has better performance than two other types of cells. Furthermore, the cell with an MPL on only the cathode increases the water flux from cathode to anode as compared to the cells with MPLs on both electrodes and cells without MPL. Oxygen-mass-transport resistances of cells in the presence of an MPL on the cathode are lower than the values for the other two cells, which indicates that the molar concentration of oxygen at the reaction surface of the catalyst layer is higher. This suggests that the MPL forces the liquid water from the cathode side to the anode side and decreases the liquid saturation in GDL at high current densities. Consequently, the MPL helps in maintaining the water content in the polymer membrane and decreases the cathode charge transfer and oxygen-mass transport resistances in PEMFCs, even when the hydrogen inlet has a low relative humidity.     

Water-transport in outer micro-porous layers for direct methanol fuel cells

The outer micro-porous layer (MPL) between the gas diffusion layer and channel of the bipolar plate was studied for both sides of the electrodes in DMFC, with particular attention to the effects of the hydrophobicity of the MPL on mass transport as well as cell performance. Water-transport behavior from the electrodes to the channel was observed through the transparent window of the single cell with membrane-electrode assemblies (MEAs) including three combinations of outer MPLs. The crossover amount of methanol as well as water through the membrane was measured, and the mass balance, based on the measured flux, was established to understand the mass transport in MEAs. The design of outer MPLs is discussed for the best cell performance.     

Facilitating mass transport in gas diffusion layer of PEMFC by fabricating micro-porous layer with dry layer preparation

For a proton exchange membrane fuel cell (PEMFC), dry layer preparation was optimized and applied to fabricate a micro-porous layer (MPL) for a gas diffusion layer (GDL). The MPLs fabricated by dry layer preparation and the conventional wet layer preparation were compared by physical and electrochemical methods. The PEMFC using dry layer MPLs showed better performance than that using wet layer MPLs, especially when the cells were operated under conditions of high oxygen utilization rate and high humidification temperature of air. The mass transport properties of the GDLs with the dry layer MPLs were also better than with the wet layer MPLs, and were found to be related to the pore size distribution in GDLs. The differences in surface morphology and pore size distribution for the GDLs with the dry layer and wet layer MPLs were investigated and analyzed. The dry layer preparation for MPLs was found to be more beneficial for forming meso-pores (pore size in the range of 0.5–15 μm), which are important and advantageous for facilitating gas transport in the GDLs. Moreover, the GDLs with the dry layer MPLs exhibited better electronic conductivity and more stable hydrophobicity than those with the wet layer MPLs. The reproducibility of the dry layer preparation for MPLs was also satisfying.     

Numerical modeling and analysis of micro-porous layer effects in polymer electrolyte fuel cells

It is well known that a micro-porous layer (MPL) plays a crucial role in the water management of polymer electrolyte fuel cells (PEFCs), and thereby, significantly stabilizes and improves cell performance. To ascertain the exact roles of MPLs, a numerical MPL model is developed in this study and incorporated with comprehensive, multi-dimensional, multi-phase fuel-cell models that have been devised earlier. The effects of different porous properties and liquid-entry pressures between an MPL and a gas diffusion layer (GDL) are examined via fully three-dimensional numerical simulations. First, when the differences in pore properties and wettability between the MPL and GDL are taken into account but the difference in the entry pressures is ignored, the numerical MPL model captures a discontinuity in liquid saturation at the GDL|MPL interface. The simulation does not, however, capture the beneficial effects of an MPL on cell performance, predicting even lower performance than in the case of no MPL. On the other hand, when a high liquid-entry pressure in an MPL is additionally considered, the numerical MPL model predicts a liquid-free MPL and successfully demonstrates the phenomenon that the high liquid-entry pressure of the MPL prevents any liquid water from entering the MPL. Consequently, it is found from the simulation results that a liquid-free MPL significantly enhances the back-flow of water across the membrane into the anode, which, in turn, helps to avoid membrane dehydration and alleviate the level of GDL flooding. As a result, the model successfully reports the beneficial effects of MPLs on PEFC performance and predicts higher performance in the presence of MPLs (e.g., an increase of 67 mV at 1.5 A cm⁻²). This study provides a fundamental explanation of the function of MPLs and quantifies the influence of their porous properties and the liquid-entry pressure on water transport and cell performance.     

Determination of the pore size distribution of micro porous layer in PEMFC using pore forming agents under various drying conditions

In this paper, the effect of the pore size distribution of a micro-porous layer (MPL) on the performance of polymer electrolyte membrane fuel cells (PEMFC) was investigated using self-made gas diffusion layers (GDLs) with different MPLs for which the pore size distribution was modified using pore forming agents under different drying conditions. When MPL dried at high temperature, more macro pores, approximately 1,000–20,000 nm in diameter, and less micro pores, below 100 nm, were observed relative to when MPL was dried at low temperature. Self-made GDLs were characterized by a field-emission scanning electron microscope (FE-SEM), mercury porosimetry and self-made gas permeability measurement equipment. The performance of the single cells was measured under two different humidification conditions. The results demonstrate that the optimum pore size distribution of MPL depended on the cell operating humidification condition. The MPL dried at high temperature performed better than the MPL dried at low temperature under a low humidification condition; however, MPL dried at low temperature performed better under a high humidification condition.     

Measurement of water transport rates across the gas diffusion layer in a proton exchange membrane fuel cell,and the influence of polytetrafluoroethylene content and micro-porous layer

Water management in a proton exchange membrane (PEM) fuel cell is one of the critical issues for improving fuel cell performance and durability, and water transport across the gas diffusion layer plays a key role in PEM fuel cell water management. In this work, we investigated the effects of polytetrafluoroethylene (PTFE) content and the application of a micro-porous layer (MPL) in the gas diffusion layer (GDL) on the water transport rate across the GDL. The results show that both PTFE and the MPL play a similar role of restraining water transport. The effects of different carbon loadings in the MPL on water transport were also investigated. The results demonstrate that the higher the carbon loading in the MPL, the more it reduces the water transport rate. Using the given cell hardware and components, the optimized operation conditions can be obtained based on a water balance analysis.     

An impedance study for the anode micro-porous layer in an operating direct methanol fuel cell

This study presents the benefit to an operating direct methanol fuel cell (DMFC) by coating a micro-porous layer (MPL) on the surface of anode gas diffusion layer (GDL). Taking the membrane electrode assembly (MEA) with and without the anodic MPL structure into account, the performances of the two types of MEA are evaluated by measuring the polarization curves together with the specific power density at a constant current density. Regarding the cell performances, the comparisons between the average power performances of the two different MEAs at low and high current density, various methanol concentrations and air flow rates are carried out by using the electrochemical impedance spectroscopy (EIS) technique. In contrast to conventional half cell EIS measurements, both the anode and cathode impedance spectra are measured in real-time during the discharge regime of the DMFC. As comparing each anode and cathode EIS between the two different MEAs, the influences of the anodic MPL on the anode and cathode reactions are systematically discussed and analyzed. Furthermore, the results are used to infer complete and reasonable interpretations of the combined effects caused by the anodic MPL on the full cell impedance, which correspond with the practical cell performance.     

Effects of the carbon black properties in gas diffusion layer on the performance of proton exchange membrane fuel cells

The microporous layer (MPL) as a part of diffusion medium has an important impact on mass transfer of proton exchange membrane fuel cell (PEMFC). In this study, MPLs of gas diffusion layers (GDLs) are prepared with different carbon blacks, and the properties of carbon blacks and their effects as MPLs on cell performance are systematically investigated. The results show that the GDL prepared by Acetylene Black (ACET) exhibits the best performance with a maximum power density up to 2.05 W cm⁻². Moreover, it still maintains extremely high performance with increasing current density even at humidity condition of 100% relative humidity, which means its excellent water/gas transportation capacity. This study contributes to deeply understanding the correlations between the properties of MPL material itself and their corresponding performance exhibited in cell. It also provides an important reference for enhancing cell performance and further advancing the practical applications of MPLs in PEMFC field.     

New anodic diffusive layer for passive micro-direct methanol fuel cell

The addition of carbon nanotubes (CNTs) into anodic micro-porous layer (MPL) of the membrane electrode assembly significantly improves the performance of the passive micro-direct methanol fuel cells (DMFCs). The maximum power density of ca. 32.2 mW cm⁻² at a temperature of ca. 25 °C and under air-breathing mode is achieved with pure CNTs as anode MPL material. Impedance analysis and cyclic voltammetric measurements of the anodes indicate that the increased performance of the passive DMFC with the addition of CNTs into anodic MPLs could be attributed to the decrease in charge transfer resistance of the anode reaction and to the improvement in catalyst utilization. Scanning electron microscopy measurements show the network formation within the MPL due to the one-dimensional structure of CNTs, which could be beneficial to the methanol mass transfer and to the improvement in catalyst utilization. Furthermore, the durability test of a passive DMFC after 300 h operation demonstrates that the passive DMFC with CNTs as anode MPL materials exhibits very good stability.     

Effects of the microstructure and powder compositions of a micro-porous layer for the anode on the performance of high concentration methanol fuel cell

To investigate the effects of the microstructure and powder compositions for the micro-porous layer (MPL) of an anode on the cell performance of a direct methanol fuel cell (DMFC) using a highly concentrated methanol solution up to 7 M, various powders and their compositions were applied as a filler of the MPL in the membrane electrode assembly (MEA). Several nano- and microstructured carbons such as commercial carbon black (CB), spherical activated carbon (AC), multi-walled carbon nanotube (MWCNT), and platelet carbon nanofiber (PCNF) were selected with different morphology and surface properties, and a meso-porous silica (one of SBA series) was also included for its porous and hydrophilic properties. The coating morphology and physical properties such as porosity and gas permeability were measured, and electrochemical properties of MEA with the MPL were examined by using current–voltage polarization, electrochemical impedance spectroscopy, and voltammetric analyses. A mixture of different carbons was found to be effective for lowering methanol crossover with sustaining electrical conductivity and gas permeability. A MEA with modified-anode MPLs made of CB (50 vol%) and PCNF (50 vol%) powders showed a maximum power density of 67.7 mW cm⁻² under operation with a 7 M concentration of methanol.     

Effect of cathode gas diffusion layer on water transport and cell performance in direct methanol fuel cells

The optimal design of the cathode gas diffusion layer (GDL) for direct methanol fuel cells (DMFCs) is not only to attain better cell performance, but also to achieve better water management for the DMFC system. In this work, the effects of both the PTFE loading in the cathode backing layer (BL) as well as in the micro-porous layer (MPL) and the carbon loading in the MPL on both water transport and cell performance were investigated experimentally. The experimental data showed that with the presence of a hydrophobic MPL in the GDL, the water-crossover flux through the membrane decreased slightly with increasing the PTFE loading in the BL. However, a higher PTFE loading in the BL not only lowered cell performance, but also resulted in an unstable discharging process. It was also found that the PTFE loading in the MPL had little effect on the water-crossover flux, but its effect on cell performance was substantial: the 40-wt% PTFE loading in the MPL was found to be the optimal value to achieve the best performance. The experimental results further showed that increasing the carbon loading in the MPL significantly lowered the water-crossover flux, but a too high carbon loading would decrease the cell performance as the result of the increased oxygen transport resistance; the 2.0-mg C cm⁻² carbon loading was found to exhibit the best performance.     

Understanding the role of cathode structure and property on water management and electrochemical performance of a PEM fuel cell

Water management is vital for the successful development of PEM fuel cells. Water should be carefully balanced within a PEM fuel cell to meet the conflicting requirements of membrane hydration and cathode anti-flooding. In order to understand the key factors that can improve water management and fuel cell performance, the cathodes with different structures and properties are prepared and tested in this study. The experimental results show that even though no micro-porous layer (MPL) is placed between the cathode catalyst layer (CCL) and macro-porous substrate (MaPS), a hydrophobic CCL is effective to prevent cathode flooding and keep membrane hydrated. The impedance study and the analysis of the polarization curves indicate that the optimized hydrophobic micro-porous structure in the MPL or the hydrophobic CCL could be mainly responsible for the improved water management in PEM fuel cells, which functions as a watershed to provide wicking of liquid water to the MaPS and increase the membrane hydration by enhancing the back-diffusion of water from the cathode side to the anode side through the membrane.     

Facilitation of water management in low Pt loaded PEM fuel cell by creating hydrophobic microporous layer with PTFE,FEP and PDMS polymers: Effect of polymer and carbon amounts

Microporous layers (MPLs) were prepared with different hydrophobic polymers to establish water management in polymer electrolyte membrane (PEM) fuel cells. Besides conventionally used polymers polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP), two different molecular weights (MW) of polydimethylsiloxane (PDMS) polymer were used as hydrophobic materials in MPL. Membrane electrode assemblies (MEAs) having MPLs with low MW PDMS polymer exhibited the best fuel cell performance compared to the PTFE and FEP based ones. Thus it is concluded that PDMS polymer has a great potential to be used as hydrophobic material for MPL to reduce flooding phenomena in PEM fuel cell.     

Effect of polytetrafluoroethylene-treatment and microporous layer-coating on the in-plane permeability of gas diffusion layers used in proton exchange membrane fuel cells

The in-plane permeability has been experimentally estimated for a number of carbon substrates and microporous layer (MPL)-coated gas diffusion layers (GDLs) as used in proton exchange membrane (PEM) fuel cells. The results show that the in-plane permeability of the tested carbon substrates decreases with increasing polytetrafluoroethylene (PTFE) loading and, in contrast, the greater is the PTFE loading in the MPL, the greater is the permeability. It has been shown that the in-plane permeability of the carbon substrates is reduced by an order of magnitude if they are coated with MPLs. Further, the permeability is different from one in-plane principal direction to another by a factor of about two. Finally, ignoring the inertial terms (for the reported flow rates) and the compressibility of the flowing air results in significant errors in the obtained values of the permeability.     

Ultra-low catalyst loading cathode electrode for anion-exchange membrane fuel cells

A new cathode architecture for anion-exchange membrane fuel cells (AEMFCs) is proposed and fabricated by direct deposition of palladium (Pd) particles onto the surface of the micro-porous layer (MPL) that is interfaced with a backing layer. The MPL is composed of carbon nanotubes while the backing layer is made of a carbon paper. The sputter-deposited electrode with a worm-like shape not only extends the electrochemical active surface area, but also facilitates the oxygen transport. This new cathode, albeit with a Pd loading as low as 0.035 mg cm⁻², enables the peak power density of an AEM direct ethanol fuel cell to be as high as 88 mW cm⁻² (at 60 °C), which is even higher than that using a conventional cathode with a 15-times higher Pd loading. The significance of the present work lies in the fact that the new sputter-deposited electrode is more suitable for fuel-electrolyte-fed fuel cells than the conventional electrode designed for proton-exchange membrane fuel cells (PEMFCs).     

Fabrication of a carbon nanofiber sheet as a micro-porous layer for proton exchange membrane fuel cells

A carbon nanofiber sheet (CNFS) has been prepared by electrospinning, stabilisation and subsequent carbonisation processes. Imaging with scanning electron microscope (SEM) indicates that the CNFS is formed by nonwoven nanofibers with diameters between 400 and 700 nm. The CNFS, with its three-dimensional pores, shows excellent electrical conductivity and hydrophobicity. In addition, it is found that the CNFS can be successfully applied as a micro-porous layer (MPL) in the cathode gas diffusion layer (GDL) of a proton exchange membrane fuel cell (PEMFC). The GDL with the CNFS as a MPL has higher gas permeability than a conventional GDL. Moreover, the resultant cathode GDL exhibits excellent fuel cell performance with a higher peak power density than that of a cathode GDL fabricated with a conventional MPL under the same test condition.     

Novel superhydrophobic microporous layers for enhanced performance and efficient water management in PEM fuel cells

Microporous layers (MPLs) obtained from inks containing three fluorinated polymers (perfluoroalcoxy, fluorinated ethylene propylene and a fluorinated polyurethane based on perfluoropolyether blocks) replacing conventional PTFE were prepared. Inks composition and rheological behaviour were fixed in order to apply the blade coating technique for MPL deposition. Superhydrophobic layers were obtained since contact angles higher than 150° were measured. The samples, tested in a single fuel cell at lab scale, at 60 °C and different relative humidity (RH 80/100 and 80/60, hydrogen/air) evidenced that new polymers are able to improve electrical performances reaching maximum power density values higher than those showed by conventional MPLs based fuel cells. Electrochemical impedance spectroscopy (EIS) was also carried out on the running cell using a Frequency Response Analyzer to assess the different dissipation phenomena and related losses.     

Effect of variation of hydrophobicity of anode diffusion media along the through-plane direction in direct methanol fuel cells

Reducing methanol crossover from the anode to cathode in direct methanol fuel cells (DMFCs) is critical for attaining high cell performance and fuel utilization, particularly when highly concentrated methanol fuel is fed into DMFCs. In this study, we present a novel design of anode diffusion media (DM) wherein spatial variation of hydrophobicity along the through-plane direction is realized by special polytetrafluoroethylene (PTFE) coating procedure. According to the capillary transport theory for porous media, the anode DM design can significantly affect both methanol and water transport processes in DMFCs. To examine its influence, three different membrane-electrode assemblies are fabricated and tested for various methanol feed concentrations. Polarization curves show that cell performance at high methanol feed concentration conditions is greatly improved with the anode DM design with increasing hydrophobicity toward the anode catalyst layer. In addition, we investigate the influence of the wettability of the anode microporous layer (MPL) on cell performance and show that for DMFC operation at high methanol feed concentration, the hydrophilic anode MPL fabricated with an ionomer binder is more beneficial than conventional hydrophobic MPLs fabricated with PTFE. This paper highlights that controlling wetting characteristics of the anode DM and MPL is of paramount importance for mitigating methanol crossover in DMFCs.     

Numerical modeling and experimental study of the influence of GDL properties on performance in a PEMFC

This work is to study the effect of properties of gas diffusion layer (GDL) on performance in a polymer electrolyte membrane fuel cell (PEMFC) by both numerical simulation and experiments. The 1-dimension numerical simulation using the mixture-phase model is developed to calculate polarization curve. We are able to estimate optimum GDL properties for cell performance from numerical simulation results. Various GDLs which have different properties are prepared to verify accuracy of the simulation results. The contact angle and gas permeability of GDLs are controlled by polytetrafluoroethylene (PTFE) content in micro-porous layers (MPLs). MPL slurry is prepared by homogeneous blending of carbon powder, PTFE suspension, isopropyl alcohol and glycerol. Then the slurry is coated on gas diffusion mediums (GDMs) surface with controlled thickness by blade coating method. Non-woven carbon papers which have different thicknesses of 200 μm and 380 μm are used as GDMs. The prepared GDLs are measured by surface morphology, contact angle, gas permeability and through-plane electrical resistance. Moreover, the GDLs are tested in a 25 cm² single cell at 70 °C in humidified H₂/air condition. The contact angle of GDL increases with increasing PTFE content in MPL. However, the gas permeability and through-plane electrical conductivity decrease with increasing PTFE content and thickness of GDM. These changes in properties of GDL greatly influence the cell performance. As a result, the best performance is obtained by GDL consists of 200 μm thick non-woven carbon paper as GDM and MPL contained 20 wt.% PTFE content.