Improved electrochemical performance of modified natural graphite anode for lithium secondary batteries

Modified natural graphite is synthesized by surface coating and graphitizing process on the base of spherical natural graphite. The modified natural graphite is examined discharge capacity and coulombic efficiency for the initial charge–discharge cycle. Modification process results in marked improvement in electrochemical performance for a larger discharge capacity and better coulombic efficiency. The mechanism of the enhancement are investigated by means of X-ray powder diffraction, scan electron microscopy, and physical parameters examination. The proportion of rhombohedral crystal structure was reduced by the heat treatment process. The modified natural graphite exhibits 40 mAh g⁻¹ reduction in the first irreversible capacity while the reversible capacity increased by 16 mAh g⁻¹ in comparison with pristine graphite electrode. Also, it has an excellent capacity retention of ∼94% after 100 cycles and ∼87% after 300 cycles.     

Preparation and electrochemical properties of TiO2 hollow spheres as an anode material for lithium-ion batteries

TiO₂ hollow spheres are fabricated by a sol-gel process using carbon spheres as template. The diameter and the shell thickness of the TiO₂ hollow spheres are about 400-600 nm and 60-80 nm, respectively. The electrochemical properties of the hollow spheres are investigated by galvanostatic cycling and cyclic voltammetry (CV) measurements. The initial discharge capacity reaches 291.2 mAh g⁻¹ at a current density of 60 mA g⁻¹. The average discharge capacity loss is about 1.72 mAh g⁻¹ per cycle from the 2nd to the 40th cycles and the coulombic efficiency is approximately 98% after 40 cycles, indicating excellent cycling stability and reversibility.     

Electrochemical lithium storage of TiO2 hollow microspheres assembled by nanotubes

TiO₂ hollow microspheres with the shell consisting of nanotubes have been successfully synthesized via a template-free hydrothermal process and subsequent treatments. The electrochemical properties of the anatase sample have been investigated by cyclic voltammetry and galvanostatic method. The initial Li insertion/extraction capacity at a current density of 0.2 C reach 290 and 232 mAh g⁻¹ respectively. Moreover, as-prepared TiO₂ delivers a reversible capacity of ca. 150 mAh g⁻¹ after 500 cycles at 1 C, and it also shows superior high rate performance (e.g., 90 mAh g⁻¹ at 8 C) without any modification.     

Boron doped lithium trivanadate as a cathode material for an enhanced rechargeable lithium ion batteries

Boron was doped into lithium trivanadate through an aqueous reaction process followed by heating at 100 °C. The B-LiV₃O₈ materials as a cathode in lithium batteries exhibits a specific discharge capacity of 269.4 mAh g⁻¹ at first cycle and remains 232.5 mAh g⁻¹ at cycle 100, at a current density of 150 mAh g⁻¹ in the voltage range of 1.8–4.0 V. The B-LiV₃O₈ materials show excellent stability, with the retention of 86.30% after 100 cycles. These result values are higher than those previous reports indicating B-LiV₃O₈ prepared by our synthesis method is a promising candidate as cathode material for rechargeable lithium batteries. The enhanced discharge capacities and their stabilities indicate that boron atoms promote lithium transferring and intercalating/deintercalating during the electrochemical processes and improve the electrochemical performance of LiV₃O₈ cathode.     

Surface-modified maghemite as the cathode material for lithium batteries

The inorganic–organic hybrid maghemite (γ-Fe₂O₃)/polypyrrole (PPy) was synthesized and evaluated as cathode-active material for room temperature lithium batteries. The nanometer-sized core–shell structure of the hybrid consisting of the maghemite core with surface modified by PPy was evidenced from the morphological examination. The cathode fabricated with the as-prepared hybrid material delivered an initial discharge capacity of 233 mAh g⁻¹ and a reversible capacity of ∼62 mAh g⁻¹ after 50 charge–discharge cycles. A much higher performance with an initial discharge capacity of 378 mAh g⁻¹ and a reversible capacity of ∼100 mAh g⁻¹ was achieved with the cathode based on the segregated active material, which was obtained by subjecting the as-prepared hybrid material to an additional ball-milling process. The study demonstrates the promising lithium insertion characteristics of the nanometer-sized core–shell maghemite/PPy particles prepared under optimized conditions for application in secondary batteries.     

Electrochemical characterizations of multi-layer and composite silicon-germanium anodes for Li-ion batteries using magnetron sputtering

To improve the electrochemical performance of Si film, we investigate the addition of two film forms of Ge. Si/Ge multi-layered and Si-Ge composite electrodes that are fabricated by magnetron sputtering onto Cu current collector substrates are investigated. X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and extended X-ray absorption fine structure (EXAFS) are employed to analyze the structures of the Si-Ge electrodes. When used as an anode electrode for a lithium ion battery, the first discharge capacity of a Si/Ge 150 multi-layer cell with a ratio of Si 15 nm/Ge 3 nm is 2099 mAh g⁻¹ between 1.1 and 0.01 V. A stable reversible capacity of 1559 mAh g⁻¹ is maintained after 100 cycles with a capacity retention rate of 74.25%. Additionally, the Si_0.84Ge_0.16 composite has an initial discharge capacity of 1915 mAh g⁻¹ and a capacity retention of 74.25%. In full cell tests of Si-Ge electrodes, the Si_0.84Ge_0.16/LiCoO₂ cell delivers a specific capacity of approximatly 160 mAh g⁻¹ and a capacity retention of 52.4% after 100 cycles. The results reveal that these two systems of sputtered Si-Ge electrodes can be used as anodes in lithium ion batteries with higher energy densities.     

One-dimensional nanostructures as electrode materials for lithium-ion batteries with improved electrochemical performance

One-dimensional (1D) nanosize electrode materials of lithium iron phosphate (LiFePO₄) nanowires and Co₃O₄–carbon nanotube composites were synthesized by the hydrothermal method. The as-prepared 1D nanostructures were structurally characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. We tested the electrochemical properties of LiFePO₄ nanowires as cathode and Co₃O₄–carbon nanotubes as anode in lithium-ion cells, via cyclic voltammetry and galvanostatic charge/discharge cycling. LiFePO₄ nanorod cathode demonstrated a stable performance over 70 cycles, with a remained specific capacity of 140 mAh g⁻¹. Nanocrystalline Co₃O₄–carbon nanotube composite anode exhibited a reversible lithium storage capacity of 510 mAh g⁻¹ over 50 cycles. 1D nanostructured electrode materials showed strong potential for lithium-ion batteries due to their good electrochemical performance.     

Electrochemical performance of VOMoO4 as negative electrode material for Li ion batteries

Polycrystalline samples of VOMoO₄ are prepared by a solid-state reaction method and their electrochemical properties are examined in the voltage window 0.005–3 V versus lithium. The reaction mechanism of a VOMoO₄ electrode for Li insertion/extraction is followed by ex situ X-ray diffraction analysis. During initial discharge, a large capacity (1280 mAh g⁻¹) is observed and corresponds to the reaction of ∼10.3 Li. The ex situ XRD patterns indicate the formation of the crystalline phase Li₄MoO₅ during the initial stages of discharge, which transforms irreversibly to amorphous phases on further discharge to 0.005 V. On cycling, the reversible capacity is due to the extraction/insertion of lithium from the amorphous phases. A discharge capacity of 320 mAh g⁻¹ is obtained after 80 cycles when cycling is performed at a current density of 120 mA g⁻¹.     

Synthesis and electrochemical performance of doped LiCoO2 materials

Layered intercalation compounds LiM_0.02Co_0.98O₂ (M = Mo⁶⁺, V⁵⁺, Zr⁴⁺) have been prepared using a simple solid-state method. Morphological and structural characterization of the synthesized powders is reported along with their electrochemical performance when used as the active material in a lithium half-cell. Synchrotron X-ray diffraction patterns suggest a single phase HT-LiCoO₂ that is isostructural to α-NaFeO₂ cannot be formed by aliovalent doping with Mo, V, and Zr. Scanning electron images show that particles are well-crystallized with a size distribution in the range of 1–5 μm. Charge–discharge cycling of the cells indicated first cycle irreversible capacity loss in order of increasing magnitude was Zr (15 mAh g⁻¹), Mo (22 mAh g⁻¹), and V (45 mAh g⁻¹). Prolonged cycling the Mo-doped cell produced the best performance of all dopants with a stable reversible capacity of 120 mAh g⁻¹ after 30 cycles, but was inferior to that of pure LiCoO₂.     

(NH4)0.5V2O5 nanobelt with good cycling stability as cathode material for Li-ion battery

(NH₄)_0.5V₂O₅ nanobelt is synthesized by sodium dodecyl benzene sulfonate (SDBS) assisted hydrothermal reaction as a cathode material for Li-ion battery. The as-prepared (NH₄)_0.5V₂O₅ nanobelts are 50-200 nm in diameter and several micrometers in length. The reversible lithium intercalation behavior of the nanobelts has been evaluated by cyclic voltammetry, galvanostatic discharge-charge cycling, and electrochemical impedance spectroscopy. The (NH₄)_0.5V₂O₅ delivers an initial specific discharge capacity of 225.2 mAh g⁻¹ between 1.8 and 4.0 V at 15 mA g⁻¹, and still maintains a high discharge capacity of 197.5 mAh g⁻¹ after 11 cycles. It shows good rate capability with a discharge capacity of about 180 mAh g⁻¹ remaining after 40 cycles at various rates and excellent cycling stability with the capacity retention of 81.9% after 100 cycles at 150 mA g⁻¹. Interestingly, the excess 120 mAh g⁻¹ capacity in the first charge process is observed, most of which could be attributed to the extraction of NH₄⁺ group, verified by Fourier transform Infrared (FT-IR) and X-ray diffraction (XRD) results.     

Effects of roasting temperature and modification on properties of Li2FeSiO4/C cathode

Li₂FeSiO₄/C cathodes were synthesized by combination of wet-process method and solid-state reaction at high temperature, and effects of roasting temperature and modification on properties of the Li₂FeSiO₄/C cathode were investigated. The XRD patterns of the Li₂FeSiO₄/C samples indicate that all the samples are of good crystallinity, and a little Fe₃O₄ impurity was observed in them. The primary particle size rises as the roasting temperature increases from 600 to 750 °C. The Li₂FeSiO₄/C sample synthesized at 650 °C has good electrochemical performances with an initial discharge capacity of 144.9 mAh g⁻¹ and the discharge capacity remains 136.5 mAh g⁻¹ after 10 cycles. The performance of Li₂FeSiO₄/C cathode is further improved by modification of Ni substitution. The Li₂Fe_0.9Ni_0.1SiO₄/C composite cathode has an initial discharge capacity of 160.1 mAh g⁻¹, and the discharge capacity remains 153.9 mAh g⁻¹ after 10 cycles. The diffusion coefficient of lithium in Li₂FeSiO₄/C is 1.38 × 10⁻¹² cm² s⁻¹ while that in Li₂Fe_0.9Ni_0.1SiO₄/C reaches 3.34 × 10⁻¹² cm² s⁻¹.     

Electrochemical insertion/deinsertion of sodium on NaV6O15 nanorods as cathode material of rechargeable sodium-based batteries

A well defined nano-structured material, NaV₆O₁₅ nanorods, was synthesized by a facile low temperature hydrothermal method. It can perform well as the cathode material of rechargeable sodium batteries. It was found that the NaV₆O₁₅ nanorods exhibited stable sodium-ion insertion/deinsertion reversibility and delivered 142 mAh g⁻¹ sodium ions when worked at a current density of 0.02 A g⁻¹. In galvanostatic cycling test, a specific discharge capacity of around 75 mAh g⁻¹ could be obtained after 30 cycles under 0.05 A g⁻¹ current density. Concerned to its good electrochemical performance for reversible delivery of sodium ions, it is thus expected that NaV₆O₁₅ may be used as cathode material for rechargeable sodium batteries with highly environmental friendship and low cost.     

Synthesis and electrochemical performance of Li2CoSiO4 as cathode material for lithium ion batteries

Li₂CoSiO₄ has been prepared successfully by a solution route or hydrothermal reaction for the first time, and its electrochemical performance has been investigated primarily. Reversible extraction and insertion of lithium from and into Li₂CoSiO₄ at 4.1 V versus lithium have shown that this material is a potential candidate for the cathode in lithium ion batteries. At this stage reversible electrochemical extraction was limited to 0.46 lithium per formula unit for the Li₂CoSiO₄/C composite materials, with a charge capacity of 234 mAh g⁻¹ and a discharge capacity of 75 mAh g⁻¹.     

Morphology effect on the electrochemical performance of NiO films as anodes for lithium ion batteries

NiO films were prepared by chemical bath deposition and electrodeposition method, respectively, using nickel foam as the substrate. The films were characterized by scanning electron microscopy (SEM) and the images showed that their morphologies were distinct. The NiO film prepared by chemical bath deposition was highly porous, while the film prepared by electrodeposition was dense, and both of their thickness was about 1 μm. As anode materials for lithium ion batteries, the porous NiO film prepared by chemical bath deposition exhibited higher coulombic efficiency and weaker polarization and its specific capacity after 50 cycles was 490 mAh g⁻¹ at the discharge–charge current density of 0.5 A g⁻¹, and 350 mAh g⁻¹ at 1.5 A g⁻¹, higher than the electrodeposited film (230 mAh g⁻¹ at 0.5 A g⁻¹, and 170 mAh g⁻¹ at 1.5 A g⁻¹). The better electrochemical performances of the film prepared by chemical bath deposition are attributed to its highly porous morphology, which shorted diffusion length of lithium ions, and relaxed the volume change caused by the reaction between NiO and Li⁺.     

Electrochemical performances of nanostructured Ni3P–Ni films electrodeposited on nickel foam substrate

Ni₃P–Ni films were deposited on nickel foam substrates by electrodeposition in an aqueous solution. The structure and morphology of the electrodeposited films were characterized using X-ray diffraction (XRD) and scanning electron microscope (SEM). The annealed electrodeposited films consisted of tetragonal structured Ni₃P and cubic metal Ni. As anode for lithium ion batteries, the electrochemical properties of the Ni₃P–Ni films were investigated by cyclic voltammetry (CV), electrochemical impedance spectrum (EIS) and galvanostatic charge–discharge tests. The electrodeposition time had a significant effect on the electrochemical performances of the films. The Ni₃P–Ni film electrodeposited for 20 min delivered the initial discharge capacity of 890 mAh g⁻¹. Although the irreversible capacity at the first cycle was relative large, the Ni₃P–Ni film exhibited good cycling stability and its discharging capacity still maintained 340 mAh g⁻¹ after 40 cycles.     

Cerium and zinc: Dual-doped LiMn2O4 spinels as cathode material for use in lithium rechargeable batteries

Pristine spinel lithium manganese oxide (LiMn₂O₄) and zinc- and cerium-doped lithium manganese oxide [LiZn_xCe_yMn_2−x−yO₄ (x = 0.01–0.10; y = 0.10–0.01)] are synthesized for the first time via the sol–gel route using p-amino benzoic acid as a chelating agent to obtain micron-sized particles and enhanced electrochemical performance. The sol–gel route offers shorter heating time, better homogeneity and control over stoichiometry. The resulting spinel product is characterized through various methods such as thermogravimetic and differential thermal analysis (TG/DTA), Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX) and electrochemical galvanostatic cycling studies. Charge–discharge studies of LiMn₂O₄ samples heated at 850 °C exhibit a discharge capacity of 122 mAh g⁻¹ and a corresponding 99% coulombic efficiency in the 1st cycle. The discharge capacity and cycling performance of LiZn_0.01Ce_0.01Mn_1.98O₄ is found to be superior (124 mAh g⁻¹), with a low capacity fade (0.1 mAh g⁻¹ cycle⁻¹) over the investigated 10 cycles.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

A novel sol-gel synthesis route to NaVPO4F as cathode material for hybrid lithium ion batteries

Sodium vanadium fluorophosphate, NaVPO₄F, a cathode material for hybrid lithium ion batteries has been synthesized via a modified sol-gel method followed by heat treatment. The vanadium (Ш) gel precursor as the reaction intermediate phase can be facilely prepared in ethanol under ambient conditions, and this synthesis considerably simplifies the conventional high-temperature fabrication of VPO₄. X-ray diffraction (XRD) results indicate a phase transition of NaVPO₄F from the monoclinic crystal to the tetragonal symmetry structure. Meanwhile, the scanning electron microscope (SEM) images show the obvious spatial rearrangements on the morphology of samples. The hybrid lithium ion batteries based on the tetragonal NaVPO₄F exhibit an even discharge plateau at 3.6 V vs. Li in the limited voltage range of 3.0-4.2 V, and the discharge capacity retention is up to 98.7% after 100 cycles at C/4 rate. With voltage excursion to 3.0-4.5 V, the initial charge and discharge deliver the reversible storage capacity of 117.3 and 106.8 mAh g⁻¹, respectively. Furthermore, the prepared NaVPO₄F has a capacity retention of 83% after 100th cycle at 2 C rate. The electrochemical properties reveal the reversible mixed alkali ion (Li⁺, Na⁺) insertion reactions for this fluorophosphate material.     

C-rate performance of silicon oxycarbide anodes for Li+ batteries enhanced by carbon nanotubes

We show that employing single wall carbon nanotubes (CNTs) as the conducting agent significantly increases the capacity of silicon oxycarbide anodes at high C-rates. In these anodes 515 mAh g⁻¹ can be extracted in just over 3 min. The capacity decreases to 300 mAh g⁻¹ at the same extraction rate when carbon black is used as the conducting agent. The CNT anodes have good cyclic stability, retaining 89.2% of initial capacity after 40 cycles. The coulombic efficiency ranges from 95% to 100%.     

All-solid-state lithium secondary batteries with high capacity using black phosphorus negative electrode

Black phosphorus was prepared from red phosphorus by using mixer mill and planetary ball-mill apparatuses. The composites with black phosphorus and acetylene black (AB) were also prepared by using the mixer mill apparatus. The mechanical milling of black phosphorus and AB brought about a decrease in size of secondary particles of the composites. The all-solid-state lithium cells with the composite and the Li₂S-P₂S₅ glass-ceramic electrolyte exhibited the first discharge capacity of 1962 mAh g⁻¹ and the coulombic efficiency of 89% at the current density of 0.064 mA cm⁻² (24 mA g⁻¹). The all-solid-state cells worked at 3.8 mA cm⁻² (1.47 A g⁻¹) at 25 °C and showed the excellent cycle performance with a high capacity of over 500 mAh g⁻¹ for 150 cycles. Black phosphorus is one of the most attractive negative electrodes with both high capacity and high-rate performance in all-solid-state lithium rechargeable batteries with sulfide electrolytes.